Phosphorescent PdII-PdII Emitter-Based Red OLEDs with an EQEmax of 20.52.

Three dinuclear Pd(II) complexes (1, 2, and 3) with intense red phosphorescence at room temperature are here synthesized using strong ligand field strength compounds. All three complexes are characterized by nuclear magnetic resonance, high-resolution mass spectrometry, and elemental analyses. Complexes 2 and 3 are characterized by single-crystal X-ray diffraction. The crystalline data of 2 and 3 reveal complex double-layer structures, with Pd-Pd distances of 2.8690(9) Å and 2.8584(17) Å, respectively. Furthermore, complexes 1, 2, and 3 show phosphorescence at room temperature in their solid states at the wavelengths of 678, 601, and 672 nm, respectively. In addition, they show phosphorescence at 634, 635, and 582 nm, respectively, in the 2 wt.% (PMMA) films, and phosphorescence at 670, 675, and 589 nm, respectively, in the deoxygenated CH2Cl2 solutions. Among three complexes, complex 1 shows red emission at 634 nm with phosphorescent quantum yield Ф = 67% in the 2 wt.% PMMA film. Furthermore, complex 1-based organic light-emitting diode is fabricated using a vapor-phase deposition process, and their maximum external quantum efficiency reaches 20.52%, which is the highest percentage obtained by using the dinuclear Pd(II) complex triplet emitters with the CIE coordinates of (0.62, 0.38).

Developing a Multi-Spectral NIR LED-Based Instrument for the Detection of Pesticide Residues Containing Chlorpyrifos-Methyl in Rough, Brown, and Milled Rice.

A recent study showed the potential of the DA Perten 7200 NIR Spectrometer in detecting chlorpyrifos-methyl pesticide residue in rough, brown, and milled rice. However, this instrument is still lab-based and generally suited for point-of-sale testing. To provide a field-deployable version of this technique, an existing light emitting diode (LED)-based instrument that provides discrete NIR wavelength illumination and reflectance spectra over the range of 850-1550 nm was tested. Spectra were collected from rough, brown, and milled rice at different pesticide concentrations and analyzed for quantitative and qualitative measurement using partial least squares regression (PLS) and discriminant analysis (DA). Simulations for two LED-based instruments were also evaluated using corresponding segments of spectra from the DA7200 to represent LED illumination. For the simulation of the existing LED-based instrument (LEDPrototype1) fitted with 850, 910, 940, 970, 1070, 1200, 1300, 1450, and 1550 nm LED wavelengths, resulting R2 ranged from 0.52 to 0.71, and the correct classification was 70.4% to 100%. The simulation of a second LED instrument (LEDPrototype2) fitted with 980, 1050, 1200, 1300, 1450, 1550, 1600, and 1650 nm LED wavelengths showed R2 of 0.59 to 0.82 and correct classifications of 66% to 100%. These LED wavelengths were selected based on the significant wavelength regions from the PLS regression coefficients of DA7200 and the commercial availability of LED wavelengths. Results showed that it is possible to use a multi-spectral LED-based instrument to detect varying levels of chlorpyrifos-methyl pesticide residue in rough, brown, and milled rice.

Synthesis and Performance of Deep-Red Phosphorescent Iridium Complexes with Pyrone as an Auxiliary Ligand.

Two bis-cyclometalated heteroleptic iridium complexes incorporating 1-phenylisoquinoline (piq) as the main cyclometalating ligand and 3-hydroxy-2-methyl-4-pyrone (ma) or 2-ethyl-3-hydroxy-4H-pyran-4-one (ema) as the auxiliary ligand, namely Ir(piq)2(ma) (Ir-1) and Ir(piq)2(ema) (Ir-2), were developed and applied as deep-red phosphors in organic light-emitting diodes (OLEDs). The two auxiliary ligands had similar influences on the photophysical, electrochemical, and electroluminescent properties of the iridium complexes. Ir(piq)2(ma) (Ir-1) showed better luminescence performance in a simple phosphorescent OLED compared to the traditional red iridium complex Ir(piq)2(acac) and exhibited a current efficiency of 9.39 cd A-1 (EQE of 12.09%). In contrast, Ir(piq)2(ema) exhibited an efficiency of 8.6 cd A-1 (EQE of 10.19%).

Organic-Inorganic Hybrid Cuprous-Based Metal Halides with Unique Two-Dimensional Crystal Structure for White Light-Emitting Diodes.

Ternary cuprous (Cu+)-based metal halides, represented by cesium copper iodide (e.g., CsCu2I3 and Cs3Cu2I5), are garnering increasing interest for light-emitting applications owing to their intrinsically high photoluminescence quantum yield and direct bandgap. Toward electrically driven light-emitting diodes (LEDs), it is highly desirable for the light emitters to have a high structural dimensionality as it may favor efficient electrical injection. However, unlike lead-based halide perovskites whose light-emitting units can be facilely arranged in three-dimensional (3D) ways, to date, nearly all ternary Cu+-based metal halides crystallize into 0D or 1D networks of Cu-X (X = Cl, Br, I) polyhedra, whereas 3D and even 2D structures remain mostly uncharted. Here, by employing a fluorinated organic cation, we report a new kind of ternary Cu+-based metal halides, (DFPD)CuX2 (DFPD+ = 4,4-difluoropiperidinium), which exhibits unique 2D layered crystal structure. Theoretical calculations reveal a highly dispersive conduction band of (DFPD)CuBr2, which is beneficial for charge carrier injection. It is also of particular significance to find that the 2D (DFPD)CuBr2 crystals show appealing properties, including improved ambient stability and an efficient warm white-light emission, making it a promising candidate for single-component lighting and display applications.

Self-Assembled Chiral Polymers Exhibiting Amplified Circularly Polarized Electroluminescence.

Circularly polarized electroluminescence (CPEL) is highly promising in realm of 3D display and optical data storage. However, designing a groundbreaking chiral material with high comprehensive CPEL performance remains a formidable challenge. In this work, a pair of chiral polymers with self-assembled behavior is designed by integrating a chiral BN-moiety into polyfluorene backbone, named R-PBN and S-PBN, respectively. The chiral polymers show narrowband emission centered at 490 nm with full-width half maximum (FWHM) of 29 nm and high photoluminescence quantum yield (PLQY) of 79%. After thermal annealing treatment, the chiral polymers undergo self-assembly, exhibiting amplified circularly polarized luminescence (CPL) with asymmetry factor (|glum|) of up to 0.11. Moreover, the solution-processed nondoped CP-OLEDs based on the chiral polymers as emitting layers exhibit maximum external quantum efficiency (EQEmax) of 9.8%, intense CPEL activities with |gEL| of up to 0.07, and small FWHM of 36 nm, simultaneously. This represents the first case of self-assembled chiral polymers that combines high EQE, large gEL value and narrowband emission.

Short-Wave Infrared Light-Emitting Diodes Using Colloidal CuInS2 Quantum Dots with ZnI2 Dual-Passivation.

Short-wave infrared (SWIR) light-emitting diodes (LEDs) have emerged as promising technologies for diverse applications such as optical communication, biomedical imaging, surveillance, and machine vision. Colloidal quantum dots (QDs) are particularly attractive for SWIR LEDs due to their solution processability, compatibility with flexible substrates, and tunable absorption and luminescence. However, the presence of toxic elements or precious metals in most SWIR-emitting QDs poses health, environmental, and cost challenges. In this context, CuInS2 (CIS) QDs are known for low toxicity, cost-effective fabrication, and SWIR-light emitting capability. However, CIS QDs have not yet been directly utilized to fabricate SWIR LEDs to date, which is due to low particle stability, inefficient charge carrier recombination, and significantly blue-shifted luminescence after integrating into LED devices. To address challenges, we propose a dual-passivation strategy using ZnI2 as a chemical additive to enhance both the optical property of plain CIS QDs and charge carrier recombination upon LED device implementation. The resulting CIS-QD-based LEDs exhibit a stable SWIR electroluminescence (EL) peak (over 1000 nm) with a high EL radiance and a record external quantum efficiency in the SWIR region. Our study represents a significant step forward in SWIR-QLED technology, offering a pathway for the development of high-performance, low-cost, and nontoxic SWIR light sources.

Single-Molecule White Circularly Polarized Photoluminescence and Electroluminescence from Dual-Emission Enantiomers.

The strategy of integrating conformational isomerization donors and chiral acceptor in single molecule was proposed to construct white circularly polarized luminescence (WCPL) materials in this work. Consequently, a pair of dual-emission enantiomers, namely (R/S)-DO-PTZ, were designed and synthesized, which displayed white emission with blue and yellow dual-emission bands in solution and solid films at Commission Internationale de l'Eclairage (CIE) coordinates of (0.30, 0.33) and (0.33, 0.35), respectively. Meanwhile, (R/S)-DO-PTZ exhibited high PLQY of up to 67% in doped films and obvious mirror-image WCPL signals with |glum| value of 3.0 × 10-3. Moreover, white circularly polarized electroluminescence (WCPEL) based on organic light-emitting diodes (OLEDs) with (R/S)-DO-PTZ as emitters were also achieved with CIE coordinates of (0.32, 0.37) and EQEmax of 4.7%, representing the state-of-the-art level of white OLEDs based on single-molecule purely organic emitters. By optimizing the device structure, warm WCPEL devices were further obtained with |gEL| value of 2.8 × 10-3, CIE coordinates of (0.37, 0.48) and EQEmax of up to 15.6%. To our knowledge, this is the first report of CP-WOLEDs based on single-molecule purely organic emitters.

Buried interface modification and light outcoupling strategy for efficient blue perovskite light-emitting diodes.

Perovskite light-emitting diodes (PeLEDs) exhibit remarkable potential in the field of displays and solid-state lighting. However, blue PeLEDs, a key element for practical applications, still lag behind their green and red counterparts, due to a combination of strong nonradiative recombination losses and unoptimized device structures. In this report, we propose a buried interface modification strategy to address these challenges by focusing on the bottom-hole transport layer (HTL) of the PeLEDs. On the one hand, a multifunctional molecule, aminoacetic acid hydrochloride (AACl), is introduced to modify the HTL/perovskite interface to regulate the perovskite crystallization. Experimental investigations and theoretical calculations demonstrate that AACl can effectively reduce the nonradiative recombination losses in bulk perovskites by suppressing the growth of low-n perovskite phases and also the losses at the bottom interface by passivating interfacial defects. On the other hand, a self-assembly nanomesh structure is ingeniously developed within the HTLs. This nanomesh structure is meticulously crafted through the blending of poly-(9,9-dioctyl-fluorene-co-N-(4-butyl phenyl) diphenylamine) and poly (n-vinyl carbazole), significantly enhancing the light outcoupling efficiency in PeLEDs. As a result, our blue PeLEDs achieve remarkable external quantum efficiencies, 20.4% at 487 nm and 12.5% at 470 nm, which are among the highest reported values. Our results offer valuable insights and effective methods for achieving high-performance blue PeLEDs.

Optimizing charge transport in hybrid GaN-PEDOT:PSS/PMMADevice for advanced application.

Organic-inorganic hybrid light-emitting devices have garnered significant attention in the last few years due to their potential. These devices integrate the superior electron mobility of inorganic semiconductors with the remarkable optoelectronic characteristics of organic semiconductors. The inquiry focused on analyzing the optical and electrical properties of a light-emitting heterojunction that combines p-type GaN with organic materials (PEDOT, PSS, and PMMA). This heterojunction is an organic-inorganic hybrid. The procedure entailed utilizing a spin-coating technique to apply a layer of either poly(methyl methacrylate) (PMMA) or a mixture of PMMA and poly(3,4ethylenedioxythiophene)-poly(styrene sulfonate) (PEDOT: PSS) onto an indium tin oxide (ITO) substrate. Subsequently, different Nd:YAG laser pulses (200, 250, and 300 pulses) were used to administer a GaN inorganic layer onto the prepared organic layer using a pulsed laser deposition approach. Subsequently, the thermal evaporation technique was employed to deposit an aluminum electrode on the top of the organic and inorganic layers, while laser pulses were fine-tuned for optimal performance. The Hall effect investigation verifies the p-type conductivity of the GaN material. The electroluminescence studies confirmed the production of blue light by the GaN-based devices throughout a range of voltage situations, spanning from 45 to 72 V.

Defects in Nitrogen-Doped ZnO Nanoparticles and Their Effect on Light-Emitting Diodes.

In this study, the effect of defects on the acceptor properties of nitrogen-doped ZnO nanoparticles (NPs) was investigated through the fabrication of light-emitting diodes (LEDs). Nitrogen-doped ZnO NPs were synthesized by an arc discharge in-gas evaporation method and post-annealed at 800 °C in an oxygen and nitrogen atmosphere. The annealed ZnO NPs were characterized by X-ray diffraction, scanning electron microscopy, Raman spectroscopy, and photoluminescence spectroscopy. It was found that the annealing of nitrogen-doped ZnO NPs in a nitrogen environment increased the number of zinc vacancies, while annealing in an oxygen environment increased the number of oxygen vacancies due to nitrogen desorption. The output characteristics of LEDs fabricated with oxygen-annealed NPs were degraded, while those with nitrogen-annealed NPs were significantly improved. From these results, the contribution of zinc vacancies to acceptor formation in ZnO NPs was confirmed for the first time in actual pn junction devices.

Effects of carbazolyl and diphenylamino substituents bearing methoxy groups on the performance of hole-transporting materials in OLEDs.

Newly designed and synthesized derivatives of pentaphenylbenzene with methoxy-substituted carbazolyl or diphenylamino moieties were investigated to estimate their applicability as hole transport materials. Both the compounds exhibit high thermal stability. The intramolecular charge transfer is blocked for the film of the compound containing diphenylamino groups. The intermolecular charge transfer is induced in the film of carbazolyl-containing compound. The derivative of pentaphenylbenzene and diphenylamine exhibits higher hole drift mobility (2.4·10-3 cm2/V·s at the electric field of 5.5·105 V/cm) and by 0.1 eV lower ionization potential than the carbazolyl-containing compound. Both the compounds were utilized as hole-transporting materials in a series of organic light emitting diodes (OLEDs) based on of thermally activated delayed fluorescence. With the maximum values of external quantum efficiency of 25.9 % and power efficiency of 43.4 lm/W, OLEDs containing the layers of the synthesized compounds outperformed the device based on TCTA by 4 %, without the change in spectral properties. Variable angle spectroscopic ellipsometry revealed the moderate average roughness of the films of the compound deposited by the thermal vacuum evaporation technique with an arithmetic mean deviation of not more than 0.8 nm. The prominent hole transport characteristics of the compounds make them good candidates for utilization in optoelectronic devices.

Depth of cure, water absorption, and solubility of indirect composites polymerized by light-emitting diode laboratory units.

This study investigated the usefulness of a dental laboratory polymerization unit with light-emitting diode (LED) as a light source. The depth of cure (n=15), water absorption and solubility (n=9) of two indirect composite materials (Cesead N and Solidex Hardura) were evaluated by five dental laboratory polymerization units (LED Cure Master, Twinkle LED, α-Light V, α-Light II, and Hyper LII). Statistical analysis was performed by one-way ANOVA and Tukey test or non-parametric tests. Comparison of light sources for curing depth showed that metal halide had the highest value, followed by the LED group with similar values, and halogen lamps with the lowest value. The water absorption and solubility of the composite specimens polymerized with the three LED laboratory polymerization units were within the ISO recommended limit.

Effectiveness of laser pulsed irradiation for antimicrobial photodynamic therapy.

The aim of this study was to compare two types of light irradiation devices for antimicrobial photodynamic therapy (aPDT). A 660-nm light-emitting diode (LED) and a 665-nm laser diode (LD) were used for light irradiation, and 0.1 mg/L TONS 504, a cationic chlorin derivative, was used as the photosensitizer. We evaluated the light attenuation along the vertical and horizontal directions, temperature rise following light irradiation, and aPDT efficacy against Staphylococcus aureus under different conditions: TONS 504 only, light irradiation only, and TONS 504 with either LED (30 J/cm2) or LD light irradiation (continuous: 30 J/cm2; pulsed: 20 J/cm2 at 2/3 duty cycle, 10 J/cm2 at 1/3 duty cycle). Both LED and LD light intensities were inversely proportional to the square of the vertical distance from the irradiated area. Along the horizontal distance from the nadir of the light source, the LED light intensity attenuated according to the cosine quadrature law, while the LD light intensity did not attenuate within the measurable range. Following light irradiation, the temperature rise increased as the TONS 504 concentration increased in the order of pulsed LD < continuous LD < LED irradiation. aPDT with light irradiation only or TONS 504 only had no antimicrobial effect, while aPDT with TONS 504 under continuous or pulsed LD light irradiation provided approximately 3 log reduction at 30 J/cm2 and 20 J/cm2 and approximately 2 log reduction at 10 J/cm2. TONS 504-aPDT under pulsed LD light irradiation provided anti-microbial effect without significant temperature rise.

How long does the biological effect of a red light-emitting diode last on adipose-derived mesenchymal stem cells?

This research investigated the duration of the influence of red light-emitting diodes (LED, 630 nm; output power: 2452.5 mW; laser beam: 163.5 cm2; irradiance: 15 mW/cm2; radiant exposure: 4 J/cm2) on different periods after irradiation (6, 12, 24, 48, and 72 h) on adipose-derived mesenchymal stem cells' (AdMSCs) metabolism and paracrine factors. AdMSCs were irradiated three times every 48 h. Twenty-four hours after the last irradiation, there was a higher MTT absorbance, followed by a decrease after 48 h. The cells' secretome showed increased levels of IL-6 and VEGF after 12 and 24 h, but this was reversed after 48 h. Additionally, LED irradiation resulted in higher levels of nitrite and did not affect oxidative stress markers. LED irradiation had significant effects on AdMSCs after 24 h compared to other groups and its control group.

Protective Effect of Red Light-Emitting Diode against UV-B Radiation-Induced Skin Damage in SKH:HR-2 Hairless Mice.

In this in vivo study on hairless mice, we examined the effects of light-emitting diode (LED) treatment applied prior to ultraviolet B (UVB) irradiation. We found that pre-treating with LED improved skin morphological and histopathological conditions compared to those only exposed to UVB irradiation. In our study, histological evaluation of collagen and elastic fibers after LED treatment prior to UVB irradiation showed that this pretreatment significantly enhanced the quality of fibers, which were otherwise poor in density and irregularly arranged due to UV exposure alone. This suggests that LED treatment promotes collagen and elastin production, leading to improved skin properties. Additionally, we observed an increase in Claudin-1 expression and a reduction in nuclear factor-erythroid 2-related factor 2 (Nrf-2) and heme-oxygenase 1 (HO-1) expression within the LED-treated skin tissues, suggesting that LED therapy may modulate key skin barrier proteins and oxidative stress markers. These results demonstrate that pretreatment with LED light can enhance the skin's resistance to UVB-induced damage by modulating gene regulation associated with skin protection. Further investigations are needed to explore the broader biological effects of LED therapy on other tissues such as blood vessels. This study underscores the potential of LED therapy as a non-invasive approach to enhance skin repair and counteract the effects of photoaging caused by UV exposure.

Effects of red-light irradiation and melatonininjection on the antioxidant capacity and occurrence of apoptosis in abalones (Haliotis discus hannai) subjected to thermal stress.

High ocean temperatures caused by global warming induce oxidative stress in aquatic organisms. Melatonin treatment and irradiation using red light-emitting diodes (LEDs) have been reported to reduce oxidative stress in a few aquatic organisms. However, the effects of red LED irradiation and melatonin injection on the antioxidant capacity and degree of apoptosis in abalones, which are nocturnal organisms, have not yet been reported. In this study, we compared the expression levels of antioxidant enzymes, total antioxidant capacity, and the degree of apoptosis in abalones subjected to red LED irradiation and melatonin treatment. The results revealed that at high water temperatures (25 °C), the mRNA expression levels of the superoxide dismutase (SOD) and glutathione peroxidase (GPx) genes and the antioxidant activity of SOD decreased in abalones in the red-LED irradiated and melatonin-treated groups compared with those in abalones in the control group. Although high water temperatures induced DNA damage in the abalone samples, the degree of apoptosis was lower in the red-LED irradiated and melatonin-treated groups than in the control group. Overall, the abalones in the melatonin-treated and red-LED irradiated groups showed reduced oxidative stress and increased antioxidant enzyme levels under thermal stress compared with those in the control group. Therefore, red LED irradiation is a promising alternative to melatonin treatment, which is difficult to administer continuously for a long time, for protecting abalones from oxidative stress.

Inactivation of Escherichia coli, Salmonella enterica, and Listeria monocytogenes using the Contamination Sanitization Inspection and Disinfection (CSI-D) device.

The Contamination Sanitization Inspection and Disinfection (CSI-D) device is a handheld fluorescence-based imaging system designed to disinfect food contact surfaces using ultraviolet-C (UVC) illumination. This study aimed to determine the optimal CSI-D parameters (i.e., UVC exposure time and intensity) for the inactivation of the following foodborne bacteria plated on non-selective media: generic Escherichia coli (indicator organism) and the pathogens enterohemorrhagic E. coli, enterotoxigenic E. coli, Salmonella enterica, and Listeria monocytogenes. Each bacterial strain was spread-plated on non-selective agar and exposed to high-intensity (10 mW/cm2) or low-intensity (5 mW/cm2) UVC for 1-5 s. Control plates were not exposed to UVC. The plates were incubated overnight at 37 °C and then enumerated. Three trials for each bacterial strain were conducted. Statistical analysis was carried out to determine if there were significant differences in bacterial growth between UVC intensities and exposure times. Overall, exposure to low or high intensity for 3-5 s resulted in consistent inhibition of bacterial growth, with reductions of 99.9-100 % for E. coli, 96.8-100 % for S. enterica, and 99.2-100 % for L. monocytogenes. The 1 s exposure time showed inconsistent results, with a 66.0-100 % reduction in growth depending on the intensity and bacterial strain. When the results for all strains within each species were combined, the 3-5 s exposure times showed significantly greater (p < 0.05) growth inhibition than the 1 s exposure time. However, there were no significant differences (p > 0.05) in growth inhibition between the high and low UVC intensities. The results of this study show that, in pure culture conditions, exposure to UVC with the CSI-D device for ≥3 s is required to achieve consistent reduction of E. coli, S. enterica, and L. monocytogenes.

Evaluation of bond strength in customizing fiber post using translucent resins photoactivated by different light-emitting diodes.

Aims: The objective of the study was to evaluate two translucent resin composite systems for customizing light-polymerized fiber posts with light-emitting diode (LED) curing units regarding adhesion using conventional cement at 24 h and 6 months. Settings and Design: This was an experimental in vitro study. Methods: Forty roots were prepared and divided into four groups (n = 10): ZV-Z350 resin and LED Valo; ZR-Z350 resin and LED Radii-Cal; OV-Opallis resin and LED Valo; and OR-Opallis resin and LED Radii-Cal. The fiber post was customized and cemented with conventional resin cement and was photoactivated by two different sources. Statistical Analysis Used: The data were subjected to two-way ANOVA and Tukey's post hoc tests (P = 0.05). The data regarding the pattern of adhesive failures were described in terms of the frequency of occurrence in each third of the postspace. Results: Both at 24 h and 6 months, bond strength among groups was similar, regardless of the analyzed postspace 3rd (P > 0.05). Adhesive failure Type 4 was the most frequent in all thirds. Conclusions: Customizing the fiber post with Z350 and Opallis has the same effect on bond strength and adhesive failure pattern, regardless of the LED curing units used for photopolymerization.

Thermally Induced Phase Separation of the PEDOT:PSS Layer for Highly Efficient Laminated Polymer Light-Emitting Diodes.

Among various conductive polymers, the poly(3,4-ethylenedioxythiophene):poly(4-styrenesulfonate) (PEDOT:PSS) film has been studied as a promising material for use as a transparent electrode and a hole-injecting layer in organic optoelectronic devices. Due to the increasing demand for the low-cost fabrication of organic light-emitting diodes (OLEDs), PEDOT:PSS has been employed as the top electrode by using the coating or lamination method. Herein, a facile method is reported for the fabrication of highly efficient polymer light-emitting diodes (PLEDs) based on a laminated transparent electrode (LTE) consisting of successive PEDOT:PSS and silver-nanowire (AgNW) layers. In particular, thermally induced phase separation (TIPS) of the PEDOT:PSS film is found to depend on the annealing temperature (Tanneal) during preparation of the LTE. At Tanneal close to the glass transition temperature of the PSS chains, a PSS-rich phase with a large number of PSS- molecules enhances the work function of the PEDOT:PSS on the glass-side surface relative to the air side. By using the optimized LTEs, bidirectional laminated PLEDs are obtained with a total external quantum efficiency of 2.9% and a turn-on voltage of 2.6 V, giving a comparable performance to that of the reference bottom-emitting PLED based on a costly evaporated metal electrode. In addition, an analysis of the angular characteristics, including the variation in the electroluminescence spectra and the change in luminance according to the emission angle, indicates that the laminated PLED with the LTE provides a more uniform angular distribution regardless of the direction of emission. Detailed optical and electrical analyses are also performed to evaluate the suitability of LTEs for the low-cost fabrication of efficient PLEDs.

InGaN blue resonant cavity micro-LED with RGY quantum dot layer for broad gamut, efficient displays.

The technology of RGBY micro resonant cavity light emitting diodes (micro-RCLEDs) based on quantum dots (QDs) is considered one of the most promising approaches for full-color displays. In this work, we propose a novel structure combining a high color conversion efficiency (CCE) QD photoresist (QDPR) color conversion layer (CCL) with blue light micro RCLEDs, incorporating an ultra-thin yellow color filter. The additional TiO2 particles inside the QDPR CCL can scatter light and disperse QDs, thus reducing the self-aggregation phenomenon and enhancing the eventual illumination uniformity. Considering the blue light leakage, the influences of adding different color filters are investigated by illumination design software. Finally, the introduction of low-temperature atomic layer deposition (ALD) passivation protection technology at the top of the CCL can enhance the device's reliability. The introduction of RGBY four-color subpixels provides a viable path for developing low-energy consumption, high uniformity, and efficient color conversion displays.