Experimental study of the two-phase flow distribution in helical-structured vertical headers.

A vertical header is a crucial component of a microchannel heat exchanger that facilitates the distribution of the two phases of the refrigerant into horizontally aligned channels. Ensuring an even distribution of the refrigerant into the channels is imperative for achieving the designed optimal performance. Previous studies have indicated that the distribution characteristics of the vertical header are contingent upon the mass flow rate and geometric properties of the header. This study aims to investigate the distribution characteristics of two-phase flow resulting from structural modifications in the header, specifically by implementing a vertical header with a helical structure. Hence, an experimental device simulating a microchannel heat exchanger found in a commercial air conditioning system was employed. The distribution characteristics of the vertically oriented header with a helical structure were measured by varying the inlet conditions (mass flow rate: 50-100 kg h-1; vapor quality: 0.1-0.2). The measured distribution characteristics were compared with those obtained from a conventional straight vertical header possessing the same cross-sectional properties. The experimental findings demonstrated that the helical structure induced a distinctive flow pattern and facilitated the mixing of the two phases. Furthermore, this helical structure exhibited reduced inertial forces compared to the simple vertical header, leading to improved distribution performance.

Fabrication of Ceramic Microchannels with Periodic Corrugated Microstructures as Catalyst Support for Hydrogen Production via Diamond Wire Sawing.

Hydrogen energy is the clean energy with the most potential in the 21st century. The microchannel reactor for methanol steam reforming (MSR) is one of the effective ways to obtain hydrogen. Ceramic materials have the advantages of high temperature resistance, corrosion resistance, and high mechanical strength, and are ideal materials for preparing the catalyst support in microchannel reactors. However, the structure of ceramic materials is hard and brittle, and the feature size of microchannel is generally not more than 1 mm, which is difficult to process using traditional processing methods. Diamond wire saw processing technology is mainly used in the slicing of hard and brittle materials such as sapphire and silicon. In this paper, a microchannel with a periodic corrugated microstructure was fabricated on a ceramic plate using diamond wire sawing, and then as a catalyst support when used in a microreactor for MSR hydrogen production. The effects of wire speed and feed speed on the amplitude and period size of the periodic corrugated microstructure were studied using a single-factor experiment. The microchannel surface morphology was observed via SEM and a 3D confocal laser microscope under different processing parameters. The microchannel samples obtained under different processing parameters were supported by a multiple impregnation method. The loading strength of the catalyst was tested via a strong wind purge experiment. The experimental results show that the periodic corrugated microstructure can significantly enhance the load strength of the catalyst. The microchannel catalyst support with the periodic corrugated microstructure was put into the microreactor for a hydrogen production experiment, and a good hydrogen production effect was obtained. The experimental results have a positive guiding effect on promoting ceramic materials as the microchannel catalyst support for the development of hydrogen energy.

Computer-Vision- and Deep-Learning-Based Determination of Flow Regimes, Void Fraction, and Resistance Sensor Data in Microchannel Flow Boiling.

The aim of this article is to introduce a novel approach to identifying flow regimes and void fractions in microchannel flow boiling, which is based on binary image segmentation using digital image processing and deep learning. The proposed image processing pipeline uses adaptive thresholding, blurring, gamma correction, contour detection, and histogram comparison to separate vapor from liquid areas, while the deep learning method uses a customized version of a convolutional neural network (CNN) called U-net to extract meaningful features from video frames. Both approaches enabled the automatic detection of flow boiling conditions, such as bubbly, slug, and annular flow, as well as automatic void fraction calculation. Especially CNN demonstrated its ability to deliver fast and dependable results, presenting an appealing substitute to manual feature extraction. The U-net-based CNN was able to segment flow boiling images with a Dice score of 99.1% and classify the above flow regimes with an overall classification accuracy of 91%. In addition, the neural network was able to predict resistance sensor readings from image data and assign them to a flow state with a mean squared error (MSE) < 10-6.

Continuous Sampling of Aerosolized Particles Using Stratified Two-Phase Microfluidics.

Health and security concerns have made it essential to develop integrated, continuous collection and sensing platforms that are compact and capable of real-time detection. In this study, we numerically investigate the flow physics associated with the single-step collection and enrichment of aerosolized polystyrene microparticles into a flowing liquid using a stratified air-water flow in a U-shaped microchannel. We validate our simulation results by comparing them to experimental data from the literature. Additionally, we fabricate an identical microfluidic device using PDMS-based soft lithography and test it to corroborate the previously published experimental data. Diversion and entrapment efficiencies are used as evaluation metrics, both of which increase with increasing particle diameter and superficial air inlet velocity. Overall, our ANSYS Fluent two-dimensional (2D) and three-dimensional (3D) multiphase flow simulations exhibit a good agreement with our experimental data and data in the literature (average deviation of ∼11%) in terms of diversion efficiency. Simulations also found the entrapment efficiency to be lower than the diversion efficiency, indicating discrepancies in the literature in terms of captured particles. The effect of the Dean force on the flow physics was also investigated using 3D simulations. We found that the effect of the Dean flow was more dominant relative to the centrifugal force on the smaller particles (e.g., 0.65 µm) compared to the larger particles (e.g., 2.1 µm). Increasing the superficial air inlet velocity also increases the effect of the centrifugal forces relative to the Dean forces. Overall, this experimentally validated multiphase model decouples and investigates the multiple and simultaneous forces on aerosolized particles flowing through a curved microchannel, which is crucial for designing more efficient capture devices. Once integrated with a microfluidic-based biosensor, this stratified flow-based microfluidic biothreat capture platform should deliver continuous sensor-ready enriched biosamples for real-time sensing.

Influence of triangular obstacles on droplet breakup dynamics in microfluidic systems.

Microfluidic devices with complex geometries and obstacles have attracted considerable interest in biomedical engineering and chemical analysis. Understanding droplet breakup behavior within these systems is crucial for optimizing their design and performance. This study investigates the influence of triangular obstacles on droplet breakup processes in microchannels. Two distinct types of triangular obstructions, positioned at the bifurcation (case I) and aligned with the flow (case II), are analyzed to evaluate their impact on droplet behavior. The investigation considers various parameters, including the Capillary number (Ca), non-dimensional droplet length (L*), non-dimensional height (A*), and non-dimensional base length (B*) of the triangle. Utilizing numerical simulations with COMSOL software, the study reveals that the presence of triangular obstacles significantly alters droplet breakup dynamics. Importantly, the shape and location of the obstacle emerge as key factors governing breakup characteristics. Results indicate faster breakup of the initial droplet when the obstacle is positioned in the center of the microchannel for case I. For case II, the study aims to identify conditions under which droplets either break up into unequal-sized entities or remain intact, depending on various flow conditions. The findings identify five distinct regimes: no breakup, breakup without a tunnel, breakup with a tunnel, droplet fragmentation into unequal-sized parts, and sorting. These regimes depend on the presence or absence of triangular obstacles and the specific flow conditions. This investigation enhances our understanding of droplet behavior within intricate microfluidic systems and provides valuable insights for optimizing the design and functionality of droplet manipulation and separation devices. Notably, the results emphasize the significant role played by triangular obstacles in droplet breakup dynamics, with the obstacle's shape and position being critical determinants of breakup characteristics.

[Direct Positron Emission Imaging Using Ultrafast Timing Performance Detectors].

This is an explanatory paper on Sun Il Kwon et al., Nat. Photon. 15: 914-918, 2021 and some parts of this manuscript are translated from the paper. Medical imaging modalities such as X-ray computed tomography, Magnetic resonance imaging, positron emission tomography (PET), and single photon emission computed tomography, require image reconstruction processes, consequently constraining them to form cylindrical shapes. However, among them, only PET can use additional information, so called time of flight, on an event-by-event basis. If coincidence time resolution (CTR) of PET detectors improved to 30 ps, which corresponds to spatial resolution of 4.5 mm, directly localizing electron-positron annihilation point is possible, allowing us to circumvent image reconstruction processes and free us from the geometric constraint. We call this concept direct positron emission imaging (dPEI). We have developed ultrafast radiation detectors by focusing on Cherenkov photon detection. Furthermore, the CTR of 32 ps being equivalent to 4.8 mm spatial resolution is achieved by combining deep learning-based signal processing with the detectors. In this article, we explain how we developed the detectors and demonstrated the first dPEI using different types of phantoms, how we will tackle limitations to be addressed to make the dPEI more practical, and how dPEI will emerge as an imaging modality in nuclear medicine.

Catalytic biodiesel production from Jatropha curcas oil: A comparative analysis of microchannel, fixed bed, and microwave reactor systems with recycled ZSM-5 catalyst.

In this study, we studied the conversion of Jatropha curcas oil to biodiesel by using three distinct reactor systems: microchannel, fixed bed, and microwave reactors. ZSM-5 was used as the catalyst for this conversion and was thoroughly characterized. X-ray diffraction was used to identify the crystalline structure, Brunauer-Emmett-Teller analysis to determine surface area, and temperature-programmed desorption to evaluate thermal stability and acidic properties. These characterizations provided crucial insights into the catalyst's structural integrity and performance under reaction conditions. The microchannel reactor exhibited superior biodiesel yield compared to the fixed bed and microwave reactors, and achieved peak efficiency at 60 °C, delivering high FAEE yield (99.7%) and conversion rates (99.92%). Ethanol catalyst volume at 1% was optimal, while varying flow rates exhibited trade-offs, emphasizing the need for nuanced control. Comparative studies against microwave and fixed-bed reactors consistently favored the microchannel reactor, emphasizing its remarkable FAME percentages, high conversion rates, and adaptability to diverse operating conditions. The zig-zag configuration enhances its efficiency, making it the optimal choice for biodiesel production and showcasing promising prospects for advancing sustainable biofuel synthesis technologies.

Kelvin-Helmholtz instability as one of the key features for fast and efficient emulsification by hydrodynamic cavitation.

The paper investigates the oil-water emulsification process inside a micro-venturi channel. More specifically, the possible influence of Kelvin-Helmholtz instability on the emulsification process. High-speed visualizations were conducted inside a square venturi constriction with throat dimensions of 450 µm by 450 µm, both under visible light and X-Rays. We show that cavity shedding caused by the instability results in the formation of several cavity vortices. Their rotation causes the deformation of the oil stream into a distinct wave-like shape, combined with fragmentation into larger drops due to cavitation bubble collapse. Later on, the cavity collapse further disperses the larger drops into a finer emulsion. Thus, it turns out that the Kelvin-Helmholtz instability is similarly characteristic for hydrodynamic cavitation emulsification inside a microchannel as is the Rayleigh-Taylor instability for acoustically driven emulsion formation.

Oxygen Vacancy-Laden Confinement Impact on Degradation of Metal Complexes.

Oxygen vacancies (Vo) have been recognized as the superior active site for PS-mediated environmental remediation; however, the formation and activation of Vo associated with the effects of chemical and spatial environments remain ambiguous. Herein, attributing to the low defect-formation energy of Vo in the presence of sulfonate groups, an in situ nucleating Vo-laden CuO nanosheet was deliberately fabricated inside the phase of a sulfonated mesoporous polystyrene substrate (Vo-CuO@SPM). The as-prepared nanocomposite demonstrated an excellent treatment efficiency toward metal complexes [Cu-EDTA as a case] with ignorable Cu(II) leaching, and it can be repeatedly employed for 25 recycles (not limited). Mechanistically, the electron transfer and the mass transport for PDS nonradical activation were proved to be substantially enhanced by the delocalized electrons and with the assistance of the microchannel environment. This work not only establishes insight into the formation of oxygen vacancies but also reveals the PS activation mechanism in the spatially confined sites.

An Experimental Investigation of R600a Condensation in a Multiport Microchannel.

This study aims to provide condensation heat transfer coefficients of R600a (isobutane) refrigerant under mass fluxes between 50 and 98 kg/m2·s at saturation temperatures of 35 °C, 40 °C and 45 °C. Additionally, experiments are conducted with varying inlet vapour quality to understand its effect on the condensation heat transfer measurement. An aluminium multiport microchannel with a hydraulic diameter (Dh) of 0.399 mm is used, where a plexiglass cover is mounted on the top of the microchannels to observe the flow conditions. A 1D heat transfer through the aluminium block is assumed, and heat flux through the refrigerant to the coolant is measured to obtain condensation heat transfer coefficients of R600a. The results showed that decreasing saturation temperature and increasing vapour quality increase the condensation heat transfer coefficient. Increasing refrigerant mass flux increases the heat transfer coefficient up to a specific mass flux. It is observed that the effect of inlet vapour quality becomes significant as introduced quality decreases due to increasing fluctuation.

Electromagnetohydrodynamic (EMHD) flow of Jeffrey fluid through a rough circular microchannel with surface charge-dependent slip.

This research examines the electromagnetohydrodynamic (EMHD) flow of Jeffrey fluid in a rough circular microchannel while considering the effect of surface charge on slip. The channel wall corrugations are described as periodic sinusoidal waves with small amplitudes. The perturbation method is employed to derive solutions for velocity and volumetric flow rate, and a combination of three-dimensional (3D) and two-dimensional (2D) graphical representations is utilized to effectively illustrate the impacts of relevant parameters on them. The significance of the Reynolds number R e $Re$ in investigations of EMHD flow is particularly emphasized. Furthermore, the effect of wall roughness ε $\varepsilon $ and wave number k $k$ on velocity and the influence of wall roughness ε $\varepsilon $ and surface charge density σ s ${\sigma }_s$ on volumetric flow rate are primarily focused on, respectively, at various Reynolds numbers. The results suggest that increasing the wall roughness leads to a reduction in velocity at low Reynolds numbers ( R e = 1 $Re = 1$ ) and an increment at high Reynolds numbers ( R e = 10 $Re = 10$ ). For any Reynolds number, a roughness with an odd multiple of wave number ( k = 6 , 10 $k = 6,10$ ) will result in a more stable velocity profile compared to one with an even multiple of wave number ( k = 4 , 8 $k = 4,8$ ). Decreasing the relaxation time λ ¯ 1 ${\bar{\lambda }}_1$ while increasing the retardation time λ ¯ 2 ${\bar{\lambda }}_2$ and Hartmann number H a $Ha$ can diminish the impact of wall roughness ε $\varepsilon $ and surface charge density σ s ${\sigma }_s$ on volumetric flow rate, independent of the Reynolds number. Interestingly, in the existence of wall roughness, further consideration of the effect of surface charge on slip leads to a 15% drop in volumetric flow rate at R e = 1 $Re = 1$ and a 32% slippage at R e = 10 $Re = 10$ . However, in the condition where the effect of surface charge on slip is considered, further examination of the presence of wall roughness only results in a 1.4% decline in volumetric flow rate at R e = 1 $Re = 1$ and a 1.6% rise at R e = 10 $Re = 10$ . These findings are crucial for optimizing the EMHD flow models in microchannels.

A channel-homogenized micro gas chromatography column for light alkane separation with uniform HKUST-1 stationary phase.

BACKGROUND: The micro gas chromatography column (µGCC) is one of the key components of the miniaturized gas chromatography system. However, light alkanes are difficult to be separated by a micro gas chromatography column, especially for methane and ethane, because the length of µGCC is limited by the area of a silicon substrate. More importantly, the heterogeneous microchannel surface formed by silicon glass bonding causes uneven stationary phase coating and the forces between the untreated microchannel surfaces and the stationary phase materials are weak, which will prevent the improvement of separation performance. RESULTS: In this paper, a micro gas chromatography column (µGCC) with uniform HKUST-1 stationary phase is reported. Significantly, an alumina film prepared by the atomic layer deposition (ALD) technique is used to homogenize the heterogeneous microchannels. The alumina is a hydrophilic material and the alumina made by the ALD technique is uniform. The forces between hydrophilic alumina film and HKUST-1 are strong, which can greatly improve the coating uniformity of the hydrophilic stationary phase HKUST-1. The test results show that the µGCC could baseline separate the light alkane mixtures (CH4, C2H6, C3H8, and C4H10) at the high testing temperature of 120 °C. The maximum resolution of the difficult-separated methane and ethane reached 19.2, which is 108 % higher than the µGCC using the same stationary phase without homogenizing the microchannel inner surface. SIGNIFICANCE: The µGCC uses ALD alumina film to homogenize the microchannel inner surface; meanwhile, hydrophilic ALD alumina has a strong electrostatic attraction with the hydrophilic stationary phase HKUST-1. Homogeneous microchannel surface and strong electrostatic attraction are favorable to obtain uniform stationary phase which greatly improves the separation performance, resulting in a large resolution for methane and ethane. The µGCC has broad application prospects in light alkane separation.

Electrochemical coalescence of oil-in-water droplets in microchannels of TiO2-x/Ti anode via polarization eliminating electrostatic repulsion and ·OH oxidation destroying oil-water interface film.

Electrochemistry is a sustainable technology for oil-water separation. In the common flat electrode scheme, due to a few centimeters away from the anode, oil droplets have to undergo electromigration to and electrical neutralization at the anodic surface before they coalesce into large oil droplets and rise to water surface, resulting in slow demulsification and easy anode fouling. Herein, a novel strategy is proposed on basis of a TiO2-x/Ti anode with microchannels to overcome these problems. When oil droplets with several microns in diameter flow through channels with tens of microns in diameter, the electromigration distance is shortened by three orders of magnitude, electrical neutralization is replaced by polarization coupling ·OH oxidation. The new strategy was supported by experimental results and theoretical analysis. Taking the suspension containing emulsified oil as targets, COD value dropped from initial 500 mg/L to 117 mg/L after flowing through anodic microchannels in only 58 s of running time, and the COD removal was 21 times higher than that for a plate anode. At similar COD removal, the residence time was 48 times shorter than that of reported flat electrodes. Coalescences of oil droplets in microchannels were observed by a confocal laser scanning microscopy. This new strategy opens a door for using microchannel electrodes to accelerate electrochemical coalescence of oil-in-water droplets.

Influence of the internal structure of straight microchannels on inertial transport behavior of particles.

The rapid advancement of Micro-Electro-Mechanical Systems (MEMS) technology has established microfluidics as a pivotal field. This technology marks the onset of a new era in various applications, including drug testing, cell culture, and disease monitoring, underscoring its extensive practicality and potential for future exploration. This research delves into the intricate behavior of particle inertial migration within microchannels, particularly focusing on the impact of different channel structures and Reynolds numbers (Re). Our studies reveal that particles in microchannels with one-sided sharp-cornered microstructures migrate towards the sharp corner at a relative position of 0.4 under low flow rates, and towards the straight wall side at a relative position of 0.8 under high flow rates. The migration pattern of equilibrium positions varies with different arrangements of sharp-corner structures, achieving stability at the channel's center only when the sharp corners are symmetrically arranged on both sides. Our investigation into the shape of microstructures indicates that sharp-cornered structures generate a more stable secondary flow compared to rectangular and semi-circular structures, preventing particle aggregation at the outlet. To address the challenges associated with handling variable cross-section geometries and solid-wall boundaries in dissipative particle dynamics methods effectively, we have developed a dissipative particle dynamics model specifically for analyzing such microchannels. Building upon our previous research, this model introduces a conservative force coefficient for particles within the microstructured region and an interaction zone that only involves repulsive forces, aligning well with experimental outcomes. Through the study of microstructures' geometric shapes, this paper offers guidance for designing microchannels for particle enrichment. Furthermore, the dissipative particle dynamics model established for the particle flow and solid structure interaction within microstructured channels provides insights into the mesoscale dynamics of liquid-solid two-phase flow and particle motion. In conclusion, this paper aims to enhance particle motion sample preparation techniques, thereby broadening the scope of microfluidic applications in the biomedical field.

[Application of microchannel technique in minimally invasive resection of cervical intraspinal tumors].

OBJECTIVE: To explore the application and key points of microchannel approaches in resection of cervical intraspinal tumors. METHODS: A retrospective analysis was performed on 51 cases of cervical spinal canal tumors from February 2017 to March 2020. Among them, 5 cases were located epidural space, 6 cases were located epidural and subdural space, and 40 cases were located under the subdural extramedullary space(6 cases were located on the ventral side of the spinal cord). The maximum diameter ranged from 0.5 to 3.0 cm. The clinical manifestations included neck, shoulder or upper limb pain 43 cases, sensory disturbance (numbness) in 22 cases, and limb weakness in 8 cases. The microchannel keyhole technique was used to expose the tumor, and the tumor was resected microscopically. RESULTS: In this study, 35 patients underwent hemilaminectomy, 12 patients underwent interlaminar fenestration, 2 patients underwent medial 1/4 facetectomy on the basis of hemilaminectomy or interlaminar fenestration. Two tumors were resected through anatomy space (no bone was resected). The degree of tumor resection included total resection in 50 cases and subtotal resection in 1 case. The type of the tumor included 36 schwannomas, 12 meningiomas, 2 enterogenic cysts and 1 dermoid cyst. There was no infection and cerebrospinal fluid leakage postoperatively. Limb numbness occurred in 7 patients. The average follow-up time was 15 months (3 to 36 months). No deformity such as cervical instability or kyphosis was found. The tumor had no recurrence. CONCLUSION: The cervical spinal canal is relatively wide, cervical tumors with no more than three segments can be fully exposed by means of microchannel technology. Besides intramedullary or malignant tumors, they can be microsurgically removed. Preservation of the skeletal muscle structure of cervical spine is beneficial to recover the anatomy and function of cervical spine. The electrophysiological monitoring helps to avoid spinal cord or nerve root injury.

Experimental and Theoretical Investigation on Heat Transfer Enhancement in Micro Scale Using Helical Connectors.

Microscale electronics have become increasingly more powerful, requiring more efficient cooling systems to manage the higher thermal loads. To meet this need, current research has been focused on overcoming the inefficiencies present in typical thermal management systems due to low Reynolds numbers within microchannels and poor physical properties of the working fluids. For the first time, this research investigated the effects of a connector with helical geometry on the heat transfer coefficient at low Reynolds numbers. The introduction of a helical connector at the inlet of a microchannel has been experimentally tested and results have shown that this approach to flow augmentation has a great potential to increase the heat transfer capabilities of the working fluid, even at low Reynolds numbers. In general, a helical connector can act as a stabilizer or a mixer, based on the characteristics of the connector for the given conditions. When the helical connector acts as a mixer, secondary flows develop that increase the random motion of molecules and possible nanoparticles, leading to an enhancement in the heat transfer coefficient in the microchannel. Otherwise, the heat transfer coefficient decreases. It is widely known that introducing nanoparticles into the working fluids has the potential to increase the thermal conductivity of the base fluid, positively impacting the heat transfer coefficient; however, viscosity also tends to increase, reducing the random motion of molecules and ultimately reducing the heat transfer capabilities of the working fluid. Therefore, optimizing the effects of nanoparticles characteristics while reducing viscous effects is essential. In this study, deionized water and deionized water-diamond nanofluid at 0.1 wt% were tested in a two-microchannel system fitted with a helical connector in between. It was found that the helical connector can make a great heat transfer coefficient enhancement in low Reynolds numbers when characteristics of geometry are optimized for given conditions.

Highly efficient semiconductor modules making controllable parallel microchannels for non-compressible hemorrhages.

Nature makes the most beautiful solution to involuted problems. Among them, the parallel tubular structures are capable of transporting fluid quickly in plant trunks and leaf stems, which demonstrate an ingenious evolutionary design. This study develops a mini-thermoelectric semiconductor P-N module to create gradient and parallel channeled hydrogels. The modules decrease quickly the temperature of polymer solution from 20 °C to -20 °C within 5 min. In addition to the exceptional liquid absorption rate, the foams exhibited shape memory mechanics. Our mini device universally makes the inspired structure in such as chitosan, gelatin, alginate and polyvinyl alcohol. Non-compressible hemorrhages are the primary cause of death in emergency. The rapid liquid absorption leads to fast activation of coagulation, which provides an efficient strategy for hemostasis management. We demonstrated this by using our semiconductor modules on collagen-kaolin parallel channel foams with their high porosity (96.43%) and rapid expansion rate (2934%). They absorb liquid with 37.25 times of the own weight, show 46.5-fold liquid absorption speed and 24-fold of blood compared with random porous foams. These superior properties lead to strong hemostatic performance in vitro and in vivo.

Optimization of Newtonian fluid pressure in microcantilever integrated flexible microfluidic channel for healthcare application.

The demand for microfluidic pressure sensors is ever-increasing in various industries due to their crucial role in controlling fluid pressure within microchannels. While syringe pump setups have been traditionally used to regulate fluid pressure in microfluidic devices, they often result in larger setups that increase the cost of the device. To address this challenge and miniaturize the syringe pump setup, the researcher introduced integrated T-microcantilever-based microfluidic devices. In these devices, microcantilevers are incorporated, and their deflections correlate with the microchannel's pressure. When the relative pressure of fluid (plasma) changes, the T-microcantilever deflects, and the extent of this deflection provides information on fluid pressure within the microchannel. In this work, finite element method (FEM) based simulation was carried out to investigate the role of material, and geometric parameters of the cantilever, and the fluid viscosity on the pressure sensing capability of the T-microcantilever integrated microfluidic channel. The T-microcantilever achieves a maximum deflection of 127µm at a 5000µm/s velocity for Young's modulus(E) of 360 kPa of PDMS by employing a hinged structure. On the other hand, a minimum deflection of 4.05 × 10-5µm was attained at 5000µm/s for Young's modulus of 1 TPa for silicon. The maximum deflected angle of the T-cantilever is 20.46° for a 360 kPa Young's modulus while the minimum deflection angle of the T-cantilever is measured at 13.77° for 900 KPa at a fluid velocity of 5000µm s-1. The T-cantilever functions as a built-in microchannel that gauges the fluid pressure within the microchannel. The peak pressure, set at 8.86 Pa on the surface of the cantilever leads to a maximum deflection of 0.096µm (approximately 1µm) in the T-cantilever at a 1:1 velocity ratio. An optimized microfluidic device embedded with microchannels can optimize fluid pressure in a microchannel support cell separation.

Development of an Open Droplet Microchannel-Based Magnetosensor for Immunofluorometric Assay of Trimethoprim in Chicken and Pork Samples with a Wide Linear Range.

Trimethoprim (TMP), functioning as a synergistic antibacterial agent, is utilized in diagnosing and treating diseases affecting livestock and poultry. Human consumption of the medication indirectly may lead to its drug accumulation in the body and increase drug resistance due to its prolonged metabolic duration in livestock and poultry, presenting significant health hazards. Most reported immunoassay techniques, such as ELISA and immunochromatographic assay (ICA), find it challenging to achieve the dual advantages of high sensitivity, simplicity of operation, and a wide detection range. Consequently, an open droplet microchannel-based magnetosensor for immunofluorometric assay (OMM-IFA) of trimethoprim was created, featuring a gel imager to provide a signal output derived from the highly specific antibody (Ab) targeting trimethoprim. The method exhibited high sensitivity in chicken and pork samples, with LODs of 0.300 and 0.017 ng/mL, respectively, and a wide linear range, covering trimethoprim's total maximum residue limits (MRLs). Additionally, the spiked recoveries in chicken and pork specimens varied between 81.6% and 107.9%, maintaining an acceptable variation coefficient below 15%, aligning well with the findings from the ultraperformance liquid chromatography-tandem mass spectrometry (UPLC-MS/MS) technique. The developed method achieved a much wider linear range of about 5 orders of magnitude of 10-2-103 levels with grayscale signals as the output signal, which exhibited high sensitivity, excellent applicability and simple operability based on magnetic automation.

Ultrasonic detection method based on flexible capillary water column arrays coupling.

Conventional water immersion ultrasonic testing faces limitations due to factors such as environmental conditions, workpiece dimensions, corrosion, and resource wastage. Contact-based coupling methods, which employ coupling media or specific coupling structures, offer a convenient approach to coupling acoustic waves and reduce signal attenuation. However, these methods are time-sensitive and lack adaptability to uneven surfaces, particularly when dealing with workpieces featuring subtle undulations, resulting in significant signal decay. This paper presents an ultrasonic coupling method based on a flexible capillary water column array. By employing a stable and flexible water column array within the micro-channels as the coupling medium, stable contact-based transmission of ultrasonic signals is achieved. The influence of water column array unit dimensions and array structures is explored through theoretical analysis and experimentation, demonstrating lower energy attenuation compared to reductions in water column area. Notably, the tests revealed the method's adaptability at oblique angles below 20°, which surpasses the performance of submerged detection at similar angles. This research presents an innovative and stable approach for contact-based ultrasonic coupling testing, particularly in scenarios involving dynamic contact scanning between ultrasonic waves and workpieces.