Production of Mayenite Nanoparticles from the Toxic Cement Dust.

To overcome the key challenges associated with cement dust, such as inhalable size, toxic ions, and the existence of large quantities of useless materials, researchers investigated an innovative and unusual conversion of toxic cement dust into Mayenite nanoparticles. Mayenite is a natural structure that can be used as a filler in a variety of industrial applications. The formation of Mayenite nanoparticles was achieved through a thermal reaction at 1000°C for 2 h between cement dust and aluminum oxide. Different techniques were used to characterize the synthesized Mayenite nanoparticles, revealing the formation of the target phase as well as the reduction of toxic ions present in cement dust. According to Scherrer's equation, the crystallite size of bypass and synthesized Mayenite nanoparticles is 45 and 30 nm, respectively. Also, with the aid of TEM analysis, the particle size distribution of the produced Mayenite nanoparticles was found to be 27±7 nm. The toxic ions, especially chlorides and sulphates, were reduced by 86% and 50%, respectively, according to X-ray fluorescence results. These findings are important for the future use of Mayenite, 12CaO.7Al2O3 (C12A7), nanoparticles formed from toxic cement dust recycling.

Design of γ-AlOOH, γ-MnOOH, and α-Mn2O3 nanorods as advanced antibacterial active agents.

In the current study, γ-AlOOH, γ-MnOOH, and α-Mn2O3 nanorods (NRs) were easily synthesized and applied as advanced antibacterial materials. γ-AlOOH NRs with 20 nm width, [100] crystal plane, and 200 nm length were fabricated through a surfactant-directed solvothermal method. γ-MnOOH NRs with 20 nm width, [101] crystal direction and 500 nm length were fabricated through a hydrothermal method. The prepared γ-MnOOH NRs were calcinated (for 5 h) at 700 °C to produce α-Mn2O3 NRs with 20 nm average width and increased surface area. The NRs' structures were confirmed through FT-IR, XRD, XPS, FESEM, and FETEM. The antibacterial activity of the NRs was studied against different Gram-negative and Gram-positive bacterial strains and yeast. The three NRs exhibited antibacterial activity against all of the used strains. Biological studies indicated that the NRs' antimicrobial activity increased in the order of γ-MnOOH < γ-AlOOH < α-Mn2O3 NRs. The α-Mn2O3 NRs exhibited the lowest MIC value (39 µg mL-1) against B. subtilis, B. pertussis, and P. aeruginosa. The prepared NRs exhibited a higher antimicrobial potential toward Gram-positive bacteria than Gram-negative bacteria. The higher antimicrobial activity of the α-Mn2O3 NRs is highlighted based on their larger surface area and smaller diameter. Consequently, uniform NR architectures, single crystallinity, small nanoscale diameters, and more highly exposed [110] Mn-polar surfaces outwards are promising structures for α-Mn2O3 antibacterial agents. These NRs adhered firmly to the bacterial cells causing cell wrapping and morphology disruption, and microbial death. The designed NRs provide a great platform for microbial growth inhibition.

Enzyme induced molecularly imprinted polymer on SERS substrate for ultrasensitive detection of patulin.

We designed a new type of MIP-SERS substrate for specific and label-free detection of patulin (PAT), by combining molecular imprinting polymer (MIP) selectivity and SERS technology sensitivity. Initially, the solid substrate of PDMS/AAO was prepared using poly dimethylsiloxane (PDMS) concreted anodized aluminum oxide (AAO) template. Then moderate Au was sputtered on the surface of PDMS/AAO to obtain Au/PDMS/AAO SERS substrate. Based on the HRP enzyme initiated in situ polymerization on the Au/PDMS/AAO, the MIP-SERS substrate was successfully synthesized with selective polymer and high tense of SERS "hot spots". The new MIP-SERS substrate showed strong SERS enhancement effect and good selectivity for PAT. Besides, the results showed that the method owned a linear range from 5 × 10-10 to 10-6 M with the limit of detection (LOD) of 8.5 × 10-11 M (S/N = 3) for PAT. The proposed method also exhibited acceptable reproducibility (relative standard deviation, RSD = 4.7%)，good stability (Raman intensity is above 80% after two weeks) and recoveries from 96.43% to 112.83% with the average RSD of 6.3%. The substrate is easy to use without complex sample pretreatment, which makes it a potential candidate as a rapid and sensitive detection method in food samples.

Mechanochemically synthesized mesoporous alumina: An advanced sorbent for post-processing concentration of 131I for cancer therapy.

High radioactive concentration of 131I in the form of 131I[NaI] solution is essential for preparation of large-dose therapeutic capsules used in the management of thyroid cancer. In this communication, we report the synthesis of mesoporous alumina sorbent (surface area = 292 ±â€¯28 m2/g, mean pore diameter = 6.8 ±â€¯0.7 nm) by a novel solid state mechanochemical approach and its utilization in post-processing concentration of 131I. The overall yield of 131I after the concentration procedure was >90% and 131I[NaI] solution could be obtained with appreciably high (1.7 TBq/mL) radioactive concentration, suitable for use in nuclear medicine. The promising results obtained in this study would stimulate greater utilization of this new class of sorbents in sample preparations by solid phase extraction procedures for societal benefits.

Formation of Mo5Si3/Mo3Si-MgAl2O4 Composites via Self-Propagating High-Temperature Synthesis.

In situ formation of intermetallic/ceramic composites composed of molybdenum silicides (Mo5Si3 and Mo3Si) and magnesium aluminate spinel (MgAl2O4) was conducted by combustion synthesis with reducing stages in the mode of self-propagating high-temperature synthesis (SHS). The SHS process combined intermetallic combustion between Mo and Si with metallothermic reduction of MoO3 by Al in the presence of MgO. Experimental evidence showed that combustion velocity and temperature decreased with increasing molar content of Mo5Si3 and Mo3Si, and therefore, the flammability limit determined for the reaction at Mo5Si3 or Mo3Si/MgAl2O4 = 2.0. Based upon combustion wave kinetics, the activation energies, Ea = 68.8 and 63.8 kJ/mol, were deduced for the solid-state SHS reactions producing Mo5Si3- and Mo3Si-MgAl2O4 composites, respectively. Phase conversion was almost complete after combustion, with the exception of trivial unreacted Mo existing in both composites and a minor amount of Mo3Si in the Mo5Si3-MgAl2O4 composite. Both composites display a dense morphology formed by connecting MgAl2O4 crystals, within which micro-sized molybdenum silicide grains were embedded. For equimolar Mo5Si3- and Mo3Si-MgAl2O4 composites, the hardness and fracture toughness are 14.6 GPa and 6.28 MPa m1/2, and 13.9 GPa and 5.98 MPa m1/2, respectively.

Facile synthesis of mesoporous alumina using hexadecyltrimethylammonium bromide (HTAB) as template: simplified sol-gel approach.

Herein the authors present the synthesis of surface functionalised mesoporous alumina (MeAl) for textural characterisation by a simplified sol-gel method obtained by using hexadecyltrimethylammonium bromide as a template. Etoricoxib (ETOX) was used as a model drug for the study. Alumina supported mesoporous material containing drug was characterised using instrumental technique namely Brunauer-Emmett-Teller surface area, Fourier transform-infrared, differential scanning calorimetry, transmission electron microscopy, X-ray diffraction, and field emission scanning electron microscopy. Diffusion study using a dialysis bag method used to check the release pattern of ETOX-loaded-MeAl. Results of characterisation study revealed the successful surface functionalisation of the drug on nanocomposite. The IC50 value obtained from cell viability study demonstrated the non-toxic behaviour of synthesised drug-loaded mesoporous alumina up to the tested concentration range. The present work has demonstrated that synthesised MeAl showed excellent stability with an expanded surface area suitable for carrier material for drug delivery system.

Mechanochemical Synthesis of CuO/MgAl2O4 and MgFe2O4 Spinels for Vanillin Production from Isoeugenol and Vanillyl Alcohol.

CuO/MgAl2O4 and CuO/MgFe2O4 catalysts were successfully synthesized with the use of spinel supports by a very simple and low-cost mechanochemical method. High-speed ball-milling was used to synthesize these catalyst supports for the first time. Materials were subsequently characterized by using XRD, FESEM, TEM, EDS-Dot mapping, XPS, BET-BJH, and Magnetic Susceptibility to investigate the physical-chemical characteristics of the catalysts. Acidity evaluation results indicated that the catalyst with the Mg-Al spinel support had more acid sites. XRD results showed a successful synthesis of the catalysts with large crystal sizes. Both catalysts were used in isoeugenol oxidation and vanillyl alcohol to vanillin reactions, with the CuO/MgAl2O4 showing optimum results. This catalyst provided 67% conversion (74% selectivity) after 2 h and this value improved to 81% (selectivity 100%) with the second reaction after 8 h. The CuO/MgFe2O4 catalyst in the first reaction after five hours revealed 53% conversion (47% selectivity) and after eight hours with the second reaction, the conversion value improved to 64% (100% selectivity). In terms of reusability, CuO/MgAl2O4 showed better results than the CuO/MgFe2O4 catalyst, for both reactions.

Gd(III)-Doped Boehmite Nanoparticle: An Emergent Material for the Fluorescent Sensing of Cr(VI) in Wastewater and Live Cells.

This article reports the effect of Gd(III) doping on the structure, microstructure, and optical properties of boehmite nanoparticles. The bright-blue fluorescence along with a long lifetime makes our material an efficient candidate for optical applications. Our material particularly targets and eliminates hexavalent chromium ions (Cr(VI)) from aqueous media, which turns it into a multifunctional fluorescent nanosensor (MFNS). The development of an efficient hexavalent chromium ion (Cr(VI)) sensor to detect and quantify Cr(VI) ions is still a serious issue worldwide. Thus, this work will be very beneficial for various environmental applications. No such work has been reported so far which includes cost-effective and biocompatible boehmite nanoparticles in this field. Detailed synthesis and characterization procedures for the MFNS have been incorporated here. The biocompatibility of the MFNS has also been studied rigorously by performing cell survivability assay (MTT) and cellular morphology assessments. Our extensive research confirmed that the "turn-off" sensing mechanism of this sensor material is based on a collisional quenching model which initiates the photoinduced electron transfer (PET) process. High selectivity and sensitivity (∼1.05 × 10-5 M) of the MFNS toward hexavalent chromium ions even in real life wastewater samples have been confirmed, which makes this fluorescent probe a potential candidate for new age imaging and sensing technologies.

Sol-gel derived boehmite nanostructures is a versatile nanoplatform for biomedical applications.

Alumina is one of the most promising carriers for drug delivery due to the long history of its usage as a vaccine adjuvant. Sol-gel synthesis provides excellent conditions for entrapment of biomolecules within an inorganic cage providing stabilization of proteins under the extremal conditions. In this paper, we show in vitro investigation of monodisperse alumina xerogel nanocontainers (AXNCs) using bovine serum albumin as a model protein entrapped in sol-gel alumina building blocks. Particularly, dose and cell-type dependent cytotoxicity in HeLa and A549 cancer cell lines were employed as well as investigation of antibacterial effect and stability of AXNCs in different biological media. It was shown, that the release of entrapped protein could be provided only in low pH buffer (as in cancer cell cytoplasm). This property could be applied for anticancer drug development. We also discovered boehmite nanoparticles effect on horizontal gene transfer and observed the appearance of antibiotic resistance by means of exchanging of the corresponding plasmid between two different E. coli strains. The present work may help to understand better the influence of AXNCs on various biological systems, such as prokaryotic and eukaryotic cells, and the activity of AXNCs in different biological media.

Antibacterial, antibiofilm, and photocatalytic activities of metals-substituted spinel cobalt ferrite nanoparticles.

This study reports the photocatalytic degradation of Methylene Blue (MB) dye (a class of dyestuffs that are resistant to biodegradation) under the influence of UV-light irradiation. Antibacterial and antibiofilm activities of ferrite nanoparticles (FO NPs) were examined against some pathogenic bacteria isolated from the medical operating room surfaces. In the same context, metals-substituted spinel cobalt ferrite nanoparticles with nominal composition [MxCo1-xFe2O4 NPs; (M = Zn, Cu, Mn; x = 0.0, 0.25, 0.5 and 0.75)] were synthesized by citrate sol-gel method. Also, the structures of the synthesized FO NPs were characterized by X-ray diffraction, and Williamson-Hall (WH) method was used to determine the crystallite size. The estimated specific surface area is found in the range from 37.99 to 107.05 m2/g, between the synthesized ferrites, Zn0.5Co0.5Fe2O4 NPs have average pore radius 1.84 nm and the pore volume was 0.136 ml/g. SEM images revealed that, the synthesized FO NPs have an unique pores and uniformly distribution, while EDX spectra shows the elemental composition for the synthesized FO NPs. The elastic properties of FO NPs have been estimated using FTIR data, whereas (M - H) hysteresis loops revealed that, by replacing cobalt ions with Zn, Cu, and Mn ions the magnetic behaviour changed from ferromagnetic to paramagnetic. Results obtained from the photocatalysis indicated that Mn0.75Co0.25Fe2O4 NPs (30.0 mg) were a promising photocatalyst achieving 96.0% removal of MB after 100 min of UV-light exposure in the alkaline solution. Antibacterial results showed that the most effective combination was Zn0.75Co0.25Fe2O4 NPs (20.0 ppm) displaying activity against Staphylococcus aureus, Enterococcus columbae, and Aerococcus viridians by 15.0, 13.0, and 12.0 mm ZOI, respectively. Additionally, Zn0.75Co0.25Fe2O4 NPs were active as antibiofilm factors producing activity by 63.7, 57.9, and 45.5% towards S. aureus, A. viridians, and E. columbae, respectively. Accordingly, Zn0.75Co0.25Fe2O4 and Mn0.75Co0.25Fe2O4 NPs can be utilized in industrial, biological and medical applications.

Fe3-xCuxO4 as highly active heterogeneous Fenton-like catalysts toward elemental mercury removal.

A series of novel spinel Fe3-xCuxO4 (0

Simultaneous adsorption of SO2 and NO from flue gas over mesoporous alumina.

Mesoporous alumina (MA) with a higher ability to simultaneously remove SO2 and NO was prepared by the evaporation-induced self-assembly process. The adsorption capacities of MA are 1.79 and 0.702 mmol/g for SO2 and NO, respectively. The Brunauer-Emmett-Teller method was used to characterize the adsorbent. Simultaneous adsorption of SO2 and NO from flue gas over MA in different operating conditions had been studied in a fixed bed reactor. The effects of temperature, oxygen concentration and water vapour were investigated. The experimental results showed that the optimum temperature for MA to simultaneously remove SO2 and NO was 90°C. The simultaneous adsorption capacities of SO2 and NO could be enhanced by increasing O2 when its concentration was below 5%. The changes of simultaneous adsorption capacities were not obvious when O2 concentration was above 5%. The increase in relative humidity results in an increase after dropping of SO2 adsorption capacity, whereas the adsorption capacity of NO showed an opposite trend. The results suggest that MA is a great adsorbent for simultaneous removal of SO2 and NO from flue gas.

Green synthesis of Al2O3 nanoparticles and their bactericidal potential against clinical isolates of multi-drug resistant Pseudomonas aeruginosa.

The high prevalence of extended-spectrum ß-lactamases (76.3 %) and metallo-ß-lactamases (7.3 %) amongst the bacteria Pseudomonas aeruginosa is a critical problem that has set forth an enormous therapeutic challenge. The suggested role of nanoparticles as next generation antibiotics, and inadequate information on antibacterial activity of aluminium oxide nanoparticles has led us to investigate the green synthesis of aluminium oxide nanoparticles (Al2O3 NPs) using leaf extracts of lemongrass and its antibacterial activity against extended-spectrum ß-lactamases and metallo-ß-lactamases clinical isolates of P. aeruginosa. The synthesized Al2O3-NPs were characterized by scanning electron microcopy, high resolution-transmission electron microscopy, atomic force microscopy, X-ray diffraction, Zeta potential, and differential light scattering techniques. The X-ray diffraction data revealed the average size of the spherical Al2O3-NPs as 34.5 nm. The hydrodynamic size in Milli Q water and Zeta potential were determined to be 254 nm and +52.2 mV, respectively. The minimal inhibitory concentration of Al2O3-NPs was found to be in the range of 1,600-3,200 µg/ml. Treatment at concentrations >2,000 µg/ml, resulted in complete growth inhibition of extended-spectrum ß-lactamases and metallo-ß-lactamases isolates. Scanning electron microcopy analysis revealed the clusters of nanoparticles attached to the bacterial cell surface, causing structural deformities in treated cells. High resolution-transmission electron microscopy analysis confirmed that nanoparticles crossed the cell membrane to become intracellular. The interaction of nanoparticles with the cell membrane eventually triggered the loss of membrane integrity, most likely due to intracellular oxidative stress. The data explicitly suggested that the synthesized Al2O3-NPs can be exploited as an effective bactericidal agent against extended-spectrum ß-lactamases, non-extended-spectrum ß-lactamases and metallo-ß-lactamases strains of P. aeruginosa, regardless of their drug resistance patterns and mechanisms. The results elucidated the clinical significance of Al2O3-NPs in developing an effective antibacterial therapeutic regimen against the multi-drug resistant bacterial infections. The use of leaf extract of lemongrass for the synthesis of Al2O3-NPs appears to be cost effective, nontoxic, eco-friendly and its strong antibacterial activity against multi-drug resistant strains of P. aeruginosa offers compatibility for pharmaceutical and other biomedical applications.

One-nanometer-precision control of Al(2)O(3) nanoshells through a solution-based synthesis route.

Forming uniform metal oxide nanocoatings is a well-known challenge in the construction of core-shell type nanomaterials. Herein, by using buffer solution as a specific reaction medium, we demonstrate the possibility to grow thin nanoshells of metal oxides, typically Al2 O3 , on different kinds of core materials, forming a uniform surface-coating layer with thicknesses achieving one nanometer precision. The application of this methodology for the surface modification of LiCoO2 shows that a thin nanoshell of Al2 O3 can be readily tuned on the surface for an optimized battery performance.

Monoacryloyl esters of carbohydrates: synthesis, polymerization and application in ceramic technology.

The article presents the interdisciplinary research among organic synthesis, chemistry of polymers and ceramic technology. It presents the synthesis of monoacryloyl esters of fructose and glucose that is 1-O-acryloyl-D-fructose and 3-O-acryloyl-D-glucose, conditions of their polymerization and application in shaping of advanced ceramic powders by the so called gelcasting method. The paper presents the influence of carbohydrate esters on the viscosity of Al2O3 suspensions and microstructure of final ceramic samples. The results showed that synthesized esters of saccharides can play the role of organic monomers able to polymerize in situ and self-cross-linking compounds in gelcasting. The paper presents the proposed structure of polymeric network which is formed from acryloyl ester of glucose during gelcasting process. The paper describes rheological behaviour of slurries composed of synthesized substances and A2O3 powders, wetting angles of alumina substrate by synthesized compounds, differences in glass transition temperatures of polymers and the microstructure of obtained final ceramic samples.

Issues in nanocomposite ceramic engineering: focus on processing and properties of alumina-based composites.

Ceramic nanocomposites, containing at least one phase in the nanometric dimension, have received special interest in recent years. They have, in fact, demonstrated increased performance, reliability and lifetime with respect to monolithic ceramics. However, a successful approach to the production of tailored composite nanostructures requires the development of innovative concepts at each step of manufacturing, from the synthesis of composite nanopowders, to their processing and sintering.This review aims to deepen understanding of some of the critical issues associated with the manufacturing of nanocomposite ceramics, focusing on alumina-based composite systems. Two case studies are presented and briefly discussed. The former illustrates the benefits, in terms of sintered microstructure and related mechanical properties, resulting from the application of an engineering approach to a laboratory-scale protocol for the elaboration of nanocomposites in the system alumina-ZrO2-YAG (yttrium aluminium garnet). The latter illustrates the manufacturing of alumina-based composites for large-scale applications such as cutting tools, carried out by an injection molding process. The need for an engineering approach to be applied in all processing steps is demonstrated also in this second case study, where a tailored manufacturing process is required to obtain the desired results.

Chemical synthesis, characterisation, and biocompatibility of nanometre scale porous anodic aluminium oxide membranes for use as a cell culture substrate for the vero cell line: a preliminary study.

In this preliminary study we investigate for the first time the biomedical potential of using porous anodic aluminium oxide (AAO) membranes as a cell substrate for culturing the Cercopithecus aethiops (African green monkey) Kidney (Vero) epithelial cell line. One advantage of using the inorganic AAO membrane is the presence of nanometre scale pore channels that allow the exchange of molecules and nutrients across the membrane. The size of the pore channels can be preselected by adjusting the controlling parameters of a temperature controlled two-step anodization process. The cellular interaction and response of the Vero cell line with an in-house synthesised AAO membrane, a commercially available membrane, and a glass control were assessed by investigating cell adhesion, morphology, and proliferation over a 72 h period. The number of viable cells proliferating over the respective membrane surfaces revealed that the locally produced in-house AAO membrane had cells numbers similar to the glass control. The study revealed evidence of focal adhesion sites over the surface of the nanoporous membranes and the penetration of cellular extensions into the pore structure as well. The outcome of the study has revealed that nanometre scale porous AAO membranes have the potential to become practical cell culture scaffold substrates with the capability to enhance adhesion and proliferation of Vero cells.

The application of thermal solar energy to high temperature processes: case study of the synthesis of alumina from boehmite.

The aim of this paper is to evaluate the feasibility of obtaining alumina from boehmite using a free, clean, and unlimited power source as the solar energy. Boehmite was obtained by hydrothermal treatment of a hazardous waste coming from aluminum slag milling. The waste is considered as a hazardous substance because of it releasing toxic gases (hydrogen, ammonia, methane, and hydrogen sulfide) in the presence of water. The as-obtained boehmite was transformed into alumina, in air atmosphere, using a solar energy concentrator (Fresnel lens). The solar installation provides a power density of 260 W · cm(-2) which allows reaching temperatures upper than 1000 °C at few minutes of exposure. Tests were performed at different periods of time that ranged between 5 and 90 min. The percentage of transformation of boehmite into alumina was followed by the water content of samples after solar radiation exposure. Samples were characterized by X-ray diffraction, infrared spectroscopy, and thermogravimetry. Metastable aluminas started to appear at 5 min and the crystalline and stable phase corundum at 10 min of solar radiation exposure.

Advances in zirconia toughened alumina biomaterials for total joint replacement.

The objective of this article is to provide an up-to-date overview of zirconia-toughened alumina (ZTA) components used in total hip arthroplasties. The structure, mechanical properties, and available data regarding the clinical performance of ZTA are summarized. The advancements that have been made in understanding the in vivo performance of ZTA are investigated. This article concludes with a discussion of gaps in the literature related to ceramic biomaterials and avenues for future research.

Synthesis, characterization, and evaluation of simple aluminum-based adsorbents for fluoride removal from drinking water.

Simple aluminum (hydr)oxides and layered double hydroxides were synthesized using common chemicals and equipment by varying synthesis temperature, concentrations of extra sulfate and citrate, and metal oxide amendments. Aluminum (hydr)oxide samples were aged at either 25 or 200°C during synthesis and, in some cases, calcined at 600 °C. Despite yielding increased crystallinity and mineral phase changes, higher temperatures had a generally negative effect on fluoride adsorption. Addition of extra sulfate during synthesis of aluminum (hydr)oxides led to significantly higher fluoride adsorption capacity compared to aluminum (hydr)oxides prepared with extra citrate or no extra ligands. X-ray diffraction results suggest that extra sulfate led to the formation of both pseudoboehmite (γ-AlOOH) and basaluminite (Al4SO4(OH)10⋅4H2O) at 200 °C; energy dispersive X-ray spectroscopy confirmed the presence of sulfur in this solid. Treatment of aluminum (hydr)oxides with magnesium, manganese, and iron oxides did not significantly impact fluoride adsorption. While layered double hydroxides exhibited high maximum fluoride adsorption capacities, their adsorption capacities at dissolved fluoride concentrations close to the World Health Organization drinking water guideline of 1.5 mg L(-1) were much lower than those for the aluminum (hydr)oxides.