Rice husk reuse as a sustainable energy alternative in Tolima, Colombia.

Colombia has great potential to produce clean energy through the use of residual biomass from the agricultural sector, such as residues obtained from the life cycle of rice production. This document presents a mixed approach methodology study to examine the combustion of rice husks as a possible energy alternative in the Tolima department of Colombia. First, the physicochemical characteristics of the rice husk were analyzed to characterize the raw material. Next, System Advisor Model (SAM) software was used to model a bioenergy plant to obtain biochar, bio-oil, and biogas from the combustion of rice husks and generate performance matrices, such as thermal efficiency, heat rate, and capacity factor. Then, the project was evaluated for financial feasibility using a mathematical model of net present value (NPV) with a planning horizon of 5 years. Finally, a subset of the local population was surveyed to assess perspectives on the project in the region. The results of the rice husk physicochemical analysis were the following: nitrogen content (0.74%), organic carbon (38.04%), silica (18.39%), humidity determination (7.68%), ash (19.4%), presence of carbonates (< 0.01%), and pH (6.41). These properties are adequate for the combustion process. The SAM simulation showed that the heat transferred in the boiler was 3180 kW, maintaining an efficiency between 50 and 52% throughout the 12 months of the year, meaning that the rice husk can generate electricity and thermal energy. The financial analysis showed that the internal rate of return (IRR) was 6% higher than the opportunity interest rate (OIR), demonstrating economic feasibility of the project. The design and creation of a rice husk processing plant is socially and environmentally viable and has the potential to contribute to the economic development of the Tolima community and reduce greenhouse gases. Likewise, this activity has the potential to promote energy security for consumers and environmental sustainability while at the same time being economically competitive.

Insights into hydrothermal treatment of biomass blends: Assessing energy yield and ash content for biofuel enhancement.

This study explores the Hydrothermal Carbonization (HTC) treatment of lignocellulosic biomass blends, delving into the influence of several key parameters: temperature, additive nature and dosage, residence time, and biomass composition. Rapeseeds, Pinus radiata sawdust, oat husks, and pressed olive served as the studied biomasses. One hundred twenty-eight experiments were conducted to assess the effects on mass yield (MY), energy yield (EY), higher heating value (HHV), and final ash content (ASH) by a Factorial Experimental Design. The derived model equations demonstrated a robust fit to the experimental data, averaging an R2 exceeding 0.94, affirming their predictive accuracy. The observed energy yield ranged between 65% and 80%, notably with sawdust and olive blends securing EY levels surpassing 70%, while rapeseed blends exhibited the highest HHV at 25 MJ/kg. Temperature emerged as the most influential factor, resulting in an 11% decrease in MY and a substantial 2.20 MJ/kg increase in HHV. Contrastingly, blend composition and additive presence significantly impacted ASH and EY, with all blends exhibiting increased ASH in the presence of additives. Higher initial hemicellulose and aqueous extractive content in raw biomass correlated proportionally with heightened HHV.

Magnetic iron oxide nanoparticle enhanced microwave pretreatment for anaerobic digestion of meat industry sludge.

Our study investigates the effects of iron oxide (Fe3O4) nanoparticles combined microwave pretreatment on the anaerobic digestibility and soluble chemical oxygen demand (SCOD) of meat industry sludge. One of our main objectives was to see whether the different microwave-based pretreatment procedures can enhance biogas production by improving the biological availability of organic compounds. Results demonstrated that combining microwave irradiation with magnetic iron oxide nanoparticles considerably increased SCOD (enhancement ratio was above 1.5), the rate of specific biogas production, and the total cumulative specific biogas volume (more than a threefold increment), while having no negative effect on the biomethane content. Furthermore, the assessment of the sludge samples' dielectric properties (dielectric constant and loss factor measured at the frequency of 500 MHz) showed a strong correlation with SCOD changes (r = 0.9942, R2 = 0.99), offering a novel method to evaluate pretreatment efficiency.

Hydrothermal pretreatment of press mud: Characterization and potential application of hydrochar and process water.

In the present study, press mud (PM), a major waste by-product from sugar industries, was subjected to hydrothermal pretreatment (HTP) to create resource recovery opportunities. The HTP process was performed with the PM samples in a laboratory scale high pressure batch reactor (capacity = 0.7 L) at 160 °C and 200 °C temperatures (solids content = 5 % and 30 %). The pretreatment resulted in separation of solid and liquid phases which are termed as solid hydrochar (HC) and process water (PW), respectively. High heating value (HHV) of HC was âˆ¼14-18 MJ kg-1, slightly higher than that of PM (14 MJ kg-1). The thermogravimetric analysis showed about 1.5-1.7 times higher heat release from HC burning compared to that observed from combustion of PM. Apart from this, the HC and PM showed no phytotoxicity during germination of mung bean (Vigna radiata). Moreover, the biochemical methane potential test on the PW showed a generation of 167-245 mL biogas per gram of chemical oxygen demand added. Hence, the HTP offers several resource recovery opportunities from PM which may also reduce the risks of environmental degradation.

Dynamic release of siloxanes in the form of biogas from simulated municipal-solid-waste landfill and the corresponding driving mechanism.

Simulated landfill bioreactors were established and operated for 635 days to investigate the dynamic release of seven siloxanes in landfill biogas (denoted by octamethyltrisiloxane (L3), decamethyltetrasiloxane (L4), dodecamethylpentasiloxane (L5), hexamethylcyclotrisiloxane (D3), octamethylcyclotetrasiloxane (D4) and decamethylcyclopentasiloxane (D5) and dodecamethylcyclohexasiloxane (D6)). In total, 259.45, 252.73, 233.30, 80.40, 4.35, 1.67 and 1.10 mg of D5, D3, D4, D6, L4, L5 and L3 were discharged from 57 kg of municipal solid waste (MSW). More than 70 % of the siloxanes were released before day 119, indicating that the peak period of siloxane discharge occurred during the hydrolysis and acid production stage. The cyclosiloxanes (D3, D4, D5 and D6) were the dominant siloxane species in the biogas. The mass load of discharged cyclosiloxanes was more than 98 % of that of the total siloxanes. In addition to the variation in the concentration distribution profiles of the different siloxane species in the MSW, transformations among species may have an important effect on the release of siloxanes. The main transformation products were D3 and D4 with high release rates (>20 %) and high measured contents of trimethylsilanol (TMSOH) and functional microorganisms (Pseudomonas) were observed during landfilling. These results suggested that MSW degradation and transformation of siloxanes both drive the dynamic release of siloxanes during long-term landfilling.

A potential slow-release fertilizer based on biogas residue biochar: Nutrient release patterns and synergistic mechanism for improving soil fertility.

The large yield of anaerobic digestates and the suboptimal efficacy of nutrient slow-release severely limit its practical application. To address these issues, a new biochar based fertilizer (MAP@BRC) was developed using biogas residue biochar (BRC) to recover nitrogen and phosphorus from biogas slurry. The nutrient release patterns of MAP@BRC and mechanisms for enhancing soil fertility were studied, and it demonstrated excellent performance, with 59% total nitrogen and 50% total phosphorus nutrient release rates within 28 days. This was attributed to the coupling of the mechanism involving the dissolution of struvite skeletons and the release of biochar pores. Pot experiments showed that crop yield and water productivity were doubled in the MAP@BRC group compared with unfertilized planting. The application of MAP@BRC also improved soil nutrient levels, reduced soil acidification, increased microbial populations, and decreased soil heavy metal pollution risk. The key factors that contributed to the improvement in soil fertility by MAP@BRC were an increase in available nitrogen and the optimization of pH levels in the soil. Overall, MAP@BRC is a safe, slow-release fertilizer that exhibits biochar-fertilizer interactions and synergistic effects. This slow-release fertilizer was prepared by treating a phosphorus-rich biogas slurry with a nitrogen-rich biogas slurry, and it simultaneously addresses problems associated with livestock waste treatment and provides a promising strategy to promote zero-waste agriculture.

Preparation of mesoporous biogas residue biochar via a self-template strategy for efficient removal of ciprofloxacin: Effect of pyrolysis temperature.

Biochar preparation and application is an anticipated pathway for the resource utilization of biogas residue. In this study, biochars were prepared by the pyrolysis of biogas residue from food waste anaerobic digestion (named as BRBCs) under various pyrolysis temperatures (300, 500, 700, and 900 °C), and the effect of pyrolysis temperatures on the physicochemical characteristics of BRBCs was examined. The adsorption performance toward ciprofloxacin (CIP), a typical antibiotic in waterbodies, was also investigated. The results showed that pyrolysis temperature significantly changed the physicochemical properties of BRBCs. In addition, the minerals in the biogas residue, especially SiO2, were rearranged to form a mesoporous structure in biochar through a self-template strategy (without activator). BRBC prepared at 900 °C exhibited a high specific surface area and pore volume, well-developed mesopore structure, and more carbon structure defects, and exhibited the largest CIP adsorption capacity with 70.29 mg g-1, which was ascribed to the combined interaction of pore diffusion, π-π interactions, hydrogen bonding, complexation, and electrostatic forces. Furthermore, the adsorption of CIP by BRBC900 was well described by two-compartment kinetic and Langmuir isotherm models. BRBC900 showed good adsorption performance toward CIP at pH 7-9. The adsorption of CIP by BRBC is a spontaneous, exothermic, entropy-increasing process. Moreover, BRBC also presented a good recycling potential. Therefore, the preparation of mesoporous biochar based on a self-template strategy not only provides an option for the resource utilization of biogas residue but also offers a new option for the treatment of antibiotic wastewater.

Nutrients recovery from dairy wastewater by Chlorella vulgaris and comparison of the lipid's composition with various chlorella strains for biodiesel production.

Microalgae biomass is regarded as a promising feedstock for biodiesel production. The biomass lipid content and fatty acids composition are among the main selective criteria when screening microalgae strains for biodiesel production. In this study, three strains of Chlorella microalgae (C. kessleri, C. sorokiniana, C. vulgaris) were cultivated nutrient media with different nitrogen contents, and on a medium with the addition of dairy wastewater. Moreover, microalgae grown on dairy wastewater allowed the removal of azote and phosphorous. The removal efficiency of 90%, 53% and 95% of ammonium nitrogen, total nitrogen and phosphate ions, respectively, were reached. The efficiency of wastewater treatment from inorganic carbon was 55%, while the maximum growth of biomass was achieved. All four samples of microalgae had a similar fatty acid profile. Palmitic acid (C16:0) was the most abundant saturated fatty acid (SFA), and is suitable for the production of biodiesel. The main unsaturated fatty acids (UFA) present in the samples were oleic acid (C18:1 n9); linoleic acid (C18:2 n6) and alpha-linolenic acid (C18:3 n3), which belong to omega-9, omega-6, omega-3, respectively.

Greenhouse gas emissions from on-site sanitation systems: A systematic review and meta-analysis of emission rates, formation pathways and influencing factors.

Onsite sanitation systems (OSS) are significant sources of greenhouse gases (GHG) including carbon dioxide (CO2), methane (CH4) and nitrous oxide (N2O). While a handful of studies have been conducted on GHG emissions from OSS, systematic evaluation of literature on this subject is limited. Our systematic review and meta-analysis provides state-of-the- art information on GHG emissions from OSS and identifies novel areas for investigation. The paper analyzes GHG emission rates from different OSS, the influence of various design, operational, and environmental factors on emission rates and proffers mitigation measures. Following the Preferred Reporting Items for Systematic reviews and Meta-analysis (PRISMA) guidelines, we identified 16 articles which quantified GHG emissions from OSS. Septic tanks emit substantial amounts of CO2 and CH4 ranging from 1.74 to 398.30 g CO2/cap/day and 0.06-110.13 g CH4/cap/day, respectively, but have low N2O emissions (0.01-0.06 g N2O/cap/day). CH4 emissions from pit latrines range from 0.77 to 20.30 g CH4/cap/day N2O emissions range from 0.76 to 1.20 gN2O/cap/day. We observed statistically significant correlations (p < 0.05) between temperature, biochemical oxygen demand, chemical oxygen demand, dissolved oxygen, storage period, and GHG emissions from OSS. However, no significant correlation (p > 0.05) was observed between soil volumetric water content and CO2 emissions. CH4 emissions (expressed as CO2 equivalents) from OSS estimated following Intergovernmental Panel for Climate Change (IPCC) guidelines were found to be seven times lower (90.99 g CO2e/cap/day) than in-situ field emission measurements (704.7 g CO2e/cap/day), implying that relying solely on IPCC guidelines may lead to underestimation of GHG emission from OSS. Our findings underscore the importance of considering local contexts and environmental factors when estimating GHG emissions from OSS. Plausible mitigation measures for GHG emissions from OSS include converting waste to biogas in anaerobic systems (e.g. biogas), applying biochar, and implementing mitigation policies that equally address inequalities in sanitation service access. Future research on GHG from OSS should focus on in-situ measurements of GHGs from pit latrines and other common OSS in developing countries, understanding the fate and transport of dissolved organics like CH4 in OSS effluents and impacts of microbial communities in OSS on GHG emissions. Addressing these gaps will enable more holistic and effective management of GHG emissions from OSS.

Design expert based optimization of the pyrolysis process for the production of cattle dung bio-oil and properties characterization.

This study aimed to optimize pyrolysis conditions to maximize bio-oil yield from cattle dung, a waste product of livestock practices. Pyrolysis of cattle dung was carried out in batch type reactor. The pyrolysis process was optimized using a central composite design in response surface methodology, with conversion parameters such as pyrolysis temperature, vapor cooling temperature, residence time, and gas flow rate taken into account. The cattle dung bio-oil was analyzed using gas chromatography/mass spectroscopy (GC/MS), an elemental analyzer, a pH probe, and a bomb calorimeter. Furthermore, the ASTM standard procedures were used to determine the bio-fuel characteristics. The optimized conditions were found to be a pyrolysis temperature of 402 °C, a vapor cooling temperature of 2.25 °C, a residence time of 30.72 min, and a gas flow rate of 1.81 l min-1, resulting in a maximum bio-oil yield of 18.9%. According to the findings, the yield of bio-oil was predominantly affected by pyrolysis temperature and vapor cooling temperature. Moreover, the bio-oil that was retrieved was discovered to be similar to conventional liquid fuels in numerous ways.

Deep eutectic solvent pretreatment of cork dust - Effects on biomass composition, phenolic extraction and anaerobic degradability.

In this study, phenolic compounds using deep eutectic solvents (DES) were extracted from cork dust, and the biogas production potential of DES-treated cork dust samples was determined. The DES treatment was carried out using choline chloride and formic acid (1:2 M ratio) at various temperatures (90, 110 and 130 °C) and treatment times (20, 40 and 60 min) at a solid-to-solvent ratio of 1:10 g mL-1. The highest total phenolic content (137 mg gallic acid equivalent (GAE) g-1 dry cork dust) was achieved at 110 °C/20 min. The extracts exhibited an antioxidant capacity of up to 56.3 ± 3.1 % 1,1-diphenyl-2-picrylhydazyl (DPPH) inhibition at a dilution rate of 100. DES treatment resulted in minimal sugar solubilization at low temperatures, while approximately 42 % of the xylan fraction in the biomass degraded under severe conditions (e.g., 130 °C/60 min). Catechin, 4-hydroxybenzoic acid and gallic acid were the major phenolics in DES extracts. The biogas yield of DES-treated cork dust increased with treatment severity. The highest biogas yield (115.1mLN gVS-1) was observed at 130 °C/60 min, representing an increase of 125 % compared to the untreated sample. SEM images revealed that the surface structure of the samples became smoother after mild pretreatment and rougher after harsh pretreatment. Compositional and FTIR analyses indicated that a higher biogas formation potential was associated with increased cellulose content in the substrate, which could be attributed to hemicellulose solubilization in the hydrolysate. Overall, DES pretreatment effectively enhanced phenol extraction and anaerobic degradability.

From grass to gas and beyond: Anaerobic digestion as a key enabling technology for a residual grass biorefinery.

Roadside grass clippings hold potential as a sustainable source of bioenergy as they do not compete with crops for land use, and are only partially utilized for low-value applications. In this study, we proposed using roadside grass as a sole feedstock for anaerobic digestion (AD) in three different settings, and assessed the potential of producing biomaterials and fertilizers from grass-based digestate. Wet continuous digestion at pilot scale and dry batch digestion at pilot and large scales resulted in biogas yields up to 700 Nm3.t-1 DOM with a methane content of 49-55 %. Despite promising results, wet AD had operational problems such as clogging and poor mixing; once upscaled, the dry digestion initially also presented an operational problem with acidification, which was overcome by the second trial. Digested grass fibers from the pilot dry AD were processed into biomaterials and performed similarly or better than the undigested fibers, while around 20 % performance reduction was observed when compared to reference wood fibers. A mass balance indicated reduced fiber recovery when higher biogas production was obtained. The liquid fraction from the pilot dry AD was characterized for its nutrient content and used as a biofertilizer in another study. In contrast, the leachate collected from the large-scale dry AD had a low nitrogen content and high chloride content that could hinder its further use. Finally, a regional market analysis was conducted showing that the biocomposites produced with the available grass fibers could substitute at least half of the current European market based on our results.

Early detection of deep-seated smouldering fires in wood waste storage using ERT.

Incidents of waste and biofuel fires are common at all stages of the waste recycling chain and have grave implications for business, employees, firefighters, society, and environment. An early detection of waste and biofuel fires in the smouldering stage could save precious lives, resources, and our environment. Existing fire detection methodologies e.g. handheld temperature sensors, IR cameras, gas sensors, and video and satellite-based monitoring techniques have inherent limitations to efficiently detect smouldering fires. An attempt was made to explore the potential of electrical resistivity tomography (ERT) as an alternate tool to address the problem. In the experiments an externally powered resistive wire was employed to initiate the smouldering fire inside the test material (wood pellets, wood shavings, wood fines). Time series of ERT that followed the initiation and development of smouldering were recorded using an automated monitoring instrument setup. The actual geometry of the experimental sample container and electrode setup was integrated in the 3D finite element method (FEM) model grid to perform inverse numerical modelling (inversion) and to develop resistivity tomographic images. The study shows a sharp increase in ratio of resistivity (R/Ro ≥ 50 %) in the test material in the region of smouldering hotspot and demonstrates the potential use of ERT technique for the detection of smouldering hotspots in silos and pile storage of organic material such as wood-based fuels, wood waste, coal, municipal solid waste (MSW), recyclables etc. More research is however required for enabling the use of this technique at the practical scale for different storage conditions.

The flow pattern effects of hydrodynamic cavitation on waste activated sludge digestibility.

The disintegration of raw sludge is of importance for enhancing biogas production and facilitates the degradation of substrates for microorganisms so that the efficiency of digestion can be increased. In this study, the effect of hydrodynamic cavitation (HC) as a pretreatment approach for waste activated sludge (WAS) was investigated at two upstream pressures (0.83 and 1.72 MPa) by using a milli-scale apparatus which makes sludge pass through an orifice with a restriction at the cross section of the flow. The HC probe made of polyether ether ketone (PEEK) material was tested using potassium iodide solution and it was made sure that cavitation occurred at the selected pressures. The analysis on chemical effects of HC bubbles collapse suggested that not only cavitation occurred at low upstream pressure, i.e., 0.83 MPa, but it also had high intensity at this pressure. The pretreatment results of HC implementation on WAS were also in agreement with the chemical characterization of HC collapse. Release of soluble organics and ammonium was observed in the treated samples, which proved the efficiency of the HC pretreatment. The methane production was improved during the digestion of the treated samples compared to the control one. The digestion of treated WAS sample at lower upstream pressure (0.83 MPa) resulted in higher methane production (128.4 mL CH4/g VS) compared to the treated sample at higher upstream pressure (119.1 mL CH4/g VS) and control sample (98.3 mL CH4/g VS). Thus, these results showed that the HC pretreatment for WAS led to a significant increase in methane production (up to 30.6%), which reveals the potential of HC in full-scale applications.

Optimizing alkali-pretreatment dosage for waste-activated sludge disintegration and enhanced biogas production yield.

The rapid transition towards modernization and industrialization led to an increase in urban population, resulting in paramount challenge to municipal sewage sludge management. Anaerobic digestion (AD) serves as a promising venue for energy recovery from waste-activated sludge (WAS). Addressing the challenge of breaking down floc structures and microbial cells is crucial for releasing extracellular polymeric substances and cytoplasmic macromolecules to facilitate hydrolysis and fermentation process. The present study aims to introduce a combined process of alkaline/acid pre-treatments and AD to enhance sludge digestion and biogas production. The study investigates the influence of alkali pretreatment at ambient temperature using four alkali reagents (NaOH, Ca(OH)2, Mg(OH)2, and KOH). The primary goal is to provide insights into the intricate interplay of alkali dosages (0.04-0.12 g/gTS) on key physic-chemical parameters crucial for optimizing the pre-treatment dosage. Under the optimized alkaline/acid pre-treatment condition, the TSS reduction of 18%-30% was achieved. An increase in sCOD concentration (24%-50%) signifies the enhanced hydrolysis and solubilization rate of organic substrate in WAS. Finally, the biomethane potential test (BMPT) was performed for pre-treated WAS samples. The maximum methane (CH4) yield was observed in combination A1 (244 mL/g) and D1 (253 mL/g), demonstrating the pivotal role of alkali optimization in enhancing AD efficiency. This study serves as a valuable resource to policymakers, researchers, and technocrats in addressing challenges associated to sludge management.

Biohydrogen from waste feedstocks: An energy opportunity for decarbonization in developing countries.

In developing economies, the decarbonization of energy sector has become a global priority for sustainable and cleaner energy system. Biohydrogen production from renewable sources of waste biomass is a good source of energy incentive that reduces the pollution. Biohydrogen has a high calorific value and emits no emissions, producing both energy security and environmental sustainability. Biohydrogen production technologies have become one of the main renewable sources of energy. The present paper entails the role of biohydrogen recovered from waste biomasses like agricultural waste (AW), organic fraction of municipal solid waste (OFMSW), food processing industrial waste (FPIW), and sewage sludge (SS) as a promising solution. The main sources of increasing yield percentage of biohydrogen generation from waste feedstock using different technologies, and process parameters are also emphasized in this review. The production paths for biohydrogen are presented in this review article, and because of advancements in R and D, biohydrogen has gained viability as a biofuel for the future and discusses potential applications in power generation, transportation, and industrial processes, emphasizing the versatility and potential for integration into existing energy infrastructure. The investigation of different biochemical technologies and methods for producing biohydrogen, including anaerobic digestion (AD), dark fermentation (DF), photo fermentation (PF), and integrated dark-photo fermentation (IDPF), has been overviewed. This analysis also discusses future research, investment, and sustainable energy options transitioning towards a low-carbon future, as well as potential problems, economic impediments, and policy-related issues with the deployment of biohydrogen in emerging nations.

Stabilization of microbial network by co-digestion of swine manure and organic wastes.

The production of biogas from organic waste has attracted considerable interest as a solution to current energy and waste management challenges. This study explored the methane (CH4) production potential of swine manure (SM), food waste (FW), and tomato waste (TW) and the changes in the microbial community involved in the anaerobic digestion process. The results revealed that the CH4 production potentials of the four kinds of SM samples were influenced by the characteristics of SM (e.g., age and storage period). Among the four kinds of SM samples, the CH4 yield from the manure directly sampled from primiparous sows (SM3) was the highest. The CH4 yield was significantly improved when SM3 was co-digested with FW, but not with TW. The addition of SM fostered a stable CH4 production community by enhancing the interaction between methanogens and syntrophic bacteria. Furthermore, the addition of FW as a co-substrate may improve the functional redundancy structure of the methanogenesis-associated network. Overall, the characteristics of SM must be considered to achieve consistent CH4 yield efficiency from anaerobic digestion since CH4 production potentials of SM can be different. Also, the contribution of co-substrate to the synergistic relationship between methanogens and syntrophic bacteria can be considered when a co-substrate is selected in order to enhace CH4 yield from SM.

Environmental impacts of valorisation of crude glycerol from biodiesel production - A life cycle perspective.

Biodiesel production produces significant quantities of impure crude glycerol as a by-product. Recent increases in the global biodiesel production have led to a surplus of crude glycerol, rendering it a waste. As a result, different methods for its valorisation are currently being investigated. This paper assesses the life cycle environmental impacts of an emerging technology for purification of crude glycerol - a multi-step physico-chemical treatment - in comparison to incineration with energy recovery commonly used for its disposal. For the former, three different acids (H3PO4, H2SO4 and HCl) are considered for the acidification step in the purification process. The results suggest that the H2SO4-based treatment is the best option with 17 net-negative impacts out of the 18 categories considered; this is due to system credits for the production of purified glycerol, heat and potassium salts. In comparison to incineration with energy recovery, the H2SO4-based process has lower savings for the climate change impact (-311 versus -504 kg CO2 eq./t crude glycerol) but it performs better in ten other categories. Sensitivity analyses suggest that that the impacts of the physico-chemical treatment are highly dependent on crude glycerol composition, allocation of burdens to crude glycerol and credits for glycerol production. For example, treating crude glycerol with lower glycerol content would increase all impacts except climate change and fossil depletion due to the higher consumption of chemicals and lower production of purified glycerol. Considering crude glycerol as a useful product rather than waste and allocating to it burdens from biodiesel production would increase most impacts significantly, including climate change (22-40 %), while fossil depletion, freshwater and marine eutrophication would become net-positive. The findings of this research will be of interest to the biodiesel industry and other industrial sectors that generate crude glycerol as a by-product.

Mechanism of improving anaerobic fermentation performance of kitchen waste pretreated by ionizing irradiation-part 1: rice.

Ionizing irradiation, as a new pretreatment method for the anaerobic fermentation of organic pollutants, is featured with fast reaction speed, good treatment effect, no need to add any chemical reagents, and no secondary pollution. This study explores the mechanism of improving anaerobic fermentation performance of rice samples pretreated by cobalt-60 gamma irradiation through the influence on fermentation substrate, acidogenic phase and methanogenic phase. The results reveal that the soluble chemical oxygen demand of the irradiated rice sample at an absorbed dose of 9.6 kGy increases by 12.4 times due to the dissolution of small molecules of fat-soluble organic matter. The yield of biogas in the acidogenic phase increases by 22.2% with a slight increase in hydrogen gas content. The yield of biogas and methane gas content in the methanogenic phase increases by 27.3% and 15%, respectively. Microbial genome analysis, performed with MiSeq high-throughput sequencing and metagenomic methods, suggests the microbial abundance and metabolic functions in the anaerobic fermentation process change significantly as a result of the pretreatment by gamma irradiation.