Your browser doesn't support javascript.
loading
Show: 20 | 50 | 100
Results 1 - 20 de 2.412
Filter
1.
Water Sci Technol ; 89(10): 2812-2822, 2024 May.
Article in English | MEDLINE | ID: mdl-38822616

ABSTRACT

The sequential extraction routes of biogenic materials from sewage sludge (SS) were investigated. Physical methods (ultrasound, heating) and chemical methods (sodium hydroxide, sodium carbonate) were used to extract extracellular polymeric substances (EPS) and alginate-like extracellular polymers (ALEs) from SS. The residues after extraction were further subjected to physical methods (heating) and chemical methods (sulfuric acid, sodium hydroxide) for protein extraction. A comparison was made between sequential extraction routes and direct extraction of biomaterials from sludge in terms of extraction quantity, material properties, and applicability. The results showed that sequential extraction of biomaterials is feasible. The highest extraction quantities were obtained when using sodium carbonate for EPS and ALE extraction and sodium hydroxide for protein, reaching 449.80 mg/gVSS, 109.78 mg/gVSS, and 5447.08 mg/L, respectively. Sequential extraction procedures facilitate the extraction of biomaterials. Finally, suitable extraction methods for different application scenarios were analyzed.


Subject(s)
Sewage , Sewage/chemistry , Sodium Hydroxide/chemistry , Chemical Fractionation/methods , Carbonates/chemistry , Feasibility Studies
2.
PLoS One ; 19(6): e0302944, 2024.
Article in English | MEDLINE | ID: mdl-38857272

ABSTRACT

The uniaxial compressive strength (UCS) and elasticity modulus (E) of intact rock are two fundamental requirements in engineering applications. These parameters can be measured either directly from the uniaxial compressive strength test or indirectly by using soft computing predictive models. In the present research, the UCS and E of intact carbonate rocks have been predicted by introducing two stacking ensemble learning models from non-destructive simple laboratory test results. For this purpose, dry unit weight, porosity, P-wave velocity, Brinell surface harnesses, UCS, and static E were measured for 70 carbonate rock samples. Then, two stacking ensemble learning models were developed for estimating the UCS and E of the rocks. The applied stacking ensemble learning method integrates the advantages of two base models in the first level, where base models are multi-layer perceptron (MLP) and random forest (RF) for predicting UCS, and support vector regressor (SVR) and extreme gradient boosting (XGBoost) for predicting E. Grid search integrating k-fold cross validation is applied to tune the parameters of both base models and meta-learner. The results demonstrate the generalization ability of the stacking ensemble method in the comparison of base models in the terms of common performance measures. The values of coefficient of determination (R2) obtained from the stacking ensemble are 0.909 and 0.831 for predicting UCS and E, respectively. Similarly, the stacking ensemble yielded Root Mean Squared Error (RMSE) values of 1.967 and 0.621 for the prediction of UCS and E, respectively. Accordingly, the proposed models have superiority in the comparison of SVR and MLP as single models and RF and XGBoost as two representative ensemble models. Furthermore, sensitivity analysis is carried out to investigate the impact of input parameters.


Subject(s)
Carbonates , Compressive Strength , Elastic Modulus , Carbonates/chemistry , Carbonates/analysis , Porosity , Models, Theoretical
3.
Glob Chang Biol ; 30(6): e17371, 2024 Jun.
Article in English | MEDLINE | ID: mdl-38863267

ABSTRACT

As the balance between erosional and constructive processes on coral reefs tilts in favor of framework loss under human-induced local and global change, many reef habitats worldwide degrade and flatten. The resultant generation of coral rubble and the beds they form can have lasting effects on reef communities and structural complexity, threatening the continuity of reef ecological functions and the services they provide. To comprehensively capture changing framework processes and predict their evolution in the context of climate change, heavily colonized rubble fragments were exposed to ocean acidification (OA) conditions for 55 days. Controlled diurnal pH oscillations were incorporated in the treatments to account for the known impact of diel carbonate chemistry fluctuations on calcification and dissolution response to OA. Scenarios included contemporary pH (8.05 ± 0.025 diel fluctuation), elevated OA (7.90 ± 0.025), and high OA (7.70 ± 0.025). We used a multifaceted approach, combining chemical flux analyses, mass alteration measurements, and computed tomography scanning images to measure total and chemical bioerosion, as well as chemically driven secondary calcification. Rates of net carbonate loss measured in the contemporary conditions (1.36 kg m-2 year-1) were high compared to literature and increased in OA scenarios (elevated: 1.84 kg m-2 year-1 and high: 1.59 kg m-2 year-1). The acceleration of these rates was driven by enhanced chemical dissolution and reduced secondary calcification. Further analysis revealed that the extent of these changes was contingent on the density of the coral skeleton, in which the micro- and macroborer communities reside. Findings indicated that increased mechanical bioerosion rates occurred in rubble with lower skeletal density, which is of note considering that corals form lower-density skeletons under OA. These direct and indirect effects of OA on chemical and mechanical framework-altering processes will influence the permanence of this crucial habitat, carrying implications for biodiversity and reef ecosystem function.


Subject(s)
Anthozoa , Climate Change , Coral Reefs , Seawater , Anthozoa/physiology , Anthozoa/chemistry , Animals , Seawater/chemistry , Hydrogen-Ion Concentration , Calcification, Physiologic , Carbonates/chemistry , Carbonates/analysis , Oceans and Seas , Ocean Acidification
4.
Microb Ecol ; 87(1): 69, 2024 May 10.
Article in English | MEDLINE | ID: mdl-38730059

ABSTRACT

Biocrust inoculation and microbially induced carbonate precipitation (MICP) are tools used in restoring degraded arid lands. It remains unclear whether the ecological functions of the two tools persist when these methods are combined and subjected to freeze-thaw (FT) cycles. We hypothesized a synergetic interaction between MICP treatment and biocrust under FT cycles, which would allow both components to retain their ecological functions. We grew cyanobacterial (Nostoc commune) biocrusts on bare soil and on MICP (Sporosarcina pasteurii)-treated soil, subjecting them to repeated FT cycles simulating the Mongolian climate. Generalized linear modeling revealed that FT cycling did not affect physical structure or related functions but could increase the productivity and reduce the nutrient condition of the crust. The results confirm the high tolerance of MICP-treated soil and biocrust to FT cycling. MICP treatment + biocrust maintained higher total carbohydrate content under FT stress. Our study indicates that biocrust on biomineralized soil has a robust enough structure to endure FT cycling during spring and autumn and to promote restoration of degraded lands.


Subject(s)
Cyanobacteria , Freezing , Soil Microbiology , Soil , Soil/chemistry , Cyanobacteria/metabolism , Cyanobacteria/chemistry , Carbonates/chemistry , Carbonates/metabolism , Ecosystem , Sporosarcina/metabolism , Sporosarcina/growth & development
5.
Environ Sci Pollut Res Int ; 31(23): 34726-34737, 2024 May.
Article in English | MEDLINE | ID: mdl-38714615

ABSTRACT

Activated carbon was prepared from distilled spent grains (DSG) using K2CO3 activation and chitosan modification. The effects of activator dosage, activation temperature, and the incorporation of chitosan as a nitrogen source on the adsorption performance were studied in this paper. The activated carbons were characterised by scanning electron microscopy, X-ray photoelectron spectroscopy, and nitrogen and carbon dioxide gas adsorption. Under the optimal conditions, the BET-specific surface area, total pore volume, and microporous volume of the activated carbon were as high as 1142 m2/g, 0.62 cm3/g, and 0.40 cm3/g, respectively. Chitosan was used as the nitrogen source, and surface modification was carried out concurrently with the K2CO3 activation process. The results revealed a carbon dioxide adsorption capacity of 5.2 mmol/g at 273.15 K and 1 bar without a nitrogen source, which increased to 5.76 mmol/g after chitosan modification. The isosteric heat of adsorption of CO2 all exceed 20 kJ/mol, hinting at the coexistence of both physisorption and chemisorption. The adsorption behaviour of the DSG-based activated carbon can be well-described by the Freundlich model.


Subject(s)
Carbon Dioxide , Charcoal , Adsorption , Carbon Dioxide/chemistry , Charcoal/chemistry , Carbonates/chemistry , Chitosan/chemistry , Nitrogen/chemistry , Potassium/chemistry
6.
Environ Res ; 252(Pt 4): 119058, 2024 Jul 01.
Article in English | MEDLINE | ID: mdl-38704015

ABSTRACT

For metal-based phosphate adsorbents, the dispersity and utilization of surface metal active sites are crucial factors in their adsorption performance and synthesis cost. In this study, a biochar material modified with amorphous Zr-Ce (carbonate) oxides (BZCCO-13) was synthesized for the phosphate uptake, and the adsorption process was enhanced by magnetic field. The beside-magnetic field was shown to have a better influence than under-magnetic field on adsorption, with maximum adsorption capacities (123.67 mg P/g) 1.14-fold greater than that without magnetic field. The beside-magnetic field could also accelerate the adsorption rate, and the time to reach 90% maximum adsorption capacity decreased by 83%. BZCCO-13 has a wide range of application pHs from 5.0 to 10.0, with great selectivity and reusability. The results of XPS and ELNES showed that the "magnetophoresis" of Ce3+ under the magnetic field was the main reason for the enhanced adsorption performance. In addition, increased surface roughness, pore size and oxygen vacancies, enhanced mass transfer by Lorentz force under a magnetic field, all beneficially influenced the adsorption process. The mechanism of phosphate adsorption by BZCCO-13 could be attributed to electrostatic attraction and CO32-dominated ligand exchange. This study not only provided an effective strategy for designing highly effective phosphate adsorbents, but also provides a new light on the application of rare earth metal-based adsorbent in magnetic field.


Subject(s)
Charcoal , Phosphates , Zirconium , Adsorption , Charcoal/chemistry , Zirconium/chemistry , Phosphates/chemistry , Magnetic Fields , Oxides/chemistry , Carbonates/chemistry
7.
Waste Manag ; 184: 10-19, 2024 Jul 15.
Article in English | MEDLINE | ID: mdl-38788498

ABSTRACT

Solid waste challenges in both the tungsten and photovoltaic industries present significant barriers to achieving carbon neutrality. This study introduces an innovative strategy for the efficient extraction of valuable metals from hazardous tungsten leaching residue (W-residue) by leveraging photovoltaic silicon kerf waste (SKW) as a silicothermic reducing agent. W-residue contains 26.2% valuable metal oxides (WO3, CoO, Nb2O5, and Ta2O5) and other refractory oxides (SiO2, TiO2, etc.), while micron-sized SKW contains 91.9% Si with a surface oxide layer. The impact of SKW addition on the silicothermic reduction process for valuable metal oxides in W-residue was investigated. Incorporating SKW and Na2CO3 flux enables valuable metal oxides from W-residue to be effectively reduced and enriched as a valuable alloy phase, with unreduced refractory oxides forming a harmless slag phase during the Na2O-SiO2-TiO2 slag refining process. This process achieved an overall recovery yield of valuable metals of 91.7%, with individual recovery yields of W, Co, and Nb exceeding 90% with the addition of 8 wt.% SKW. This innovative approach not only achieves high-value recovery from W-residue and utilization of SKW but also minimizes environmental impact through an efficient and eco-friendly recycling pathway. The strategy contributes significantly to the establishment of a resource-efficient circular economy, wherein the recovered high-value alloy phase return to the tungsten supply chain, and the harmless slag phase become raw materials for microcrystalline glass production.


Subject(s)
Industrial Waste , Recycling , Tungsten , Tungsten/chemistry , Industrial Waste/analysis , Recycling/methods , Oxides/chemistry , Solid Waste/analysis , Waste Management/methods , Metals/chemistry , Carbonates/chemistry
8.
Ecotoxicol Environ Saf ; 279: 116496, 2024 Jul 01.
Article in English | MEDLINE | ID: mdl-38816322

ABSTRACT

Microbially induced carbonate precipitation (MICP), as an eco-friendly and promising technology that can transform free metal ions into stable precipitation, has been extensively used in remediation of heavy metal contamination. However, its depressed efficiency of heavy metal elimination remains in question due to the inhibition effect of heavy metal toxicity on bacterial activity. In this work, an efficient, low-cost manganese (Mn) elimination strategy by coupling MICP with chitosan biopolymer as an additive with reduced treatment time was suggested, optimized, and implemented. The influences of chitosan at different concentrations (0.01, 0.05, 0.10, 0.15 and 0.30 %, w/v) on bacterial growth, enzyme activity, Mn removal efficiency and microstructure properties of the resulting precipitation were investigated. Results showed that Mn content was reduced by 94.5 % within 12 h with 0.15 % chitosan addition through adsorption and biomineralization as MnCO3 (at an initial Mn concentration of 3 mM), demonstrating a two-thirds decrease in remediation time compared to the chitosan-absent system, whereas maximum urease activity increased by ∼50 %. Microstructure analyses indicated that the mineralized precipitates were spherical-shaped MnCO3, and a smaller size and more uniform distribution of MnCO3 is obtained by the regulation of abundant amino and hydroxyl groups in chitosan. These results demonstrate that chitosan accelerates nucleation and tunes the growth of MnCO3 by providing nucleation sites for mineral formation and alleviating the toxicity of metal ions, which has the potential to upgrade MICP process in a sustainable and effective manner. This work provides a reference for further understanding of the biomineralization regulation mechanism, and gives a new perspective into the application of biopolymer-intensified strategies of MICP technology in heavy metal contamination.


Subject(s)
Carbonates , Chitosan , Manganese , Chitosan/chemistry , Manganese/chemistry , Manganese/toxicity , Carbonates/chemistry , Adsorption , Biopolymers/chemistry , Chemical Precipitation , Water Pollutants, Chemical/toxicity , Water Pollutants, Chemical/chemistry , Urease , Environmental Restoration and Remediation/methods , Biomineralization/drug effects , Biodegradation, Environmental
9.
Bioresour Technol ; 403: 130851, 2024 Jul.
Article in English | MEDLINE | ID: mdl-38782189

ABSTRACT

A new method for green synthesis of activated carbon using chitosan-based hydrogel precursors is reported. Chitosan-based hydrogel materials are designed to absorb trace amounts of non-toxic and non-corrosive activating agent K2CO3 from dilute aqueous solution. The K2CO3 impregnated hydrogels are further freeze-dried and converted to activated carbons with tuneable pore structure by a single-step pyrolysis. Activated carbon with highest pore volume of 0.76 cm3/g and surface area of 2026 m2/g is obtained by using K2CO3 as low as 0.23 g per gram of chitosan hydrogel. It can adsorb maximum CO2 of 4.2 mmol/g at 25 °C and 1 bar. This study demonstrates that biopolymer hydrogels impregnated with trace amounts of K2CO3 are excellent precursor materials to design high surface area carbons for CO2 capture.


Subject(s)
Carbon Dioxide , Carbonates , Chitosan , Potassium , Carbon Dioxide/chemistry , Carbonates/chemistry , Adsorption , Chitosan/chemistry , Potassium/chemistry , Hydrogels/chemistry , Porosity , Charcoal/chemistry , Carbon/chemistry , Water/chemistry , Cross-Linking Reagents/chemistry , Hydrogel, Polyethylene Glycol Dimethacrylate/chemistry
10.
J Hazard Mater ; 470: 134210, 2024 May 15.
Article in English | MEDLINE | ID: mdl-38581876

ABSTRACT

Modern metallurgical and smelting activities discharge the lead-containing wastewater, causing serious threats to human health. Bacteria and urease applied to microbial-induced carbonate precipitation (MICP) and enzyme-induced carbonate precipitation (EICP) are denatured under high Pb2+ concentration. The nano-hydroxyapatite (nHAP)-assisted biomineralization technology was applied in this study for Pb immobilization. Results showed that the extracellular polymers and cell membranes failed to secure the urease activity when subjected to 60 mM Pb2+. The immobilization efficiency dropped to below 50% under MICP, whereas it due to a lack of extracellular polymers and cell membranes dropped to below 30% under EICP. nHAP prevented the attachment of Pb2+ either through competing with bacteria and urease or promoting Ca2+/Pb2+ ion exchange. Furthermore, CO32- from ureolysis replaced the hydroxyl (-OH) in hydroxylpyromorphite to encourage the formation of carbonate-bearing hydroxylpyromorphite of higher stability (Pb10(PO4)6CO3). Moreover, nHAP application overcame an inability to provide nucleation sites by urease. As a result, the immobilization efficiency, when subjected to 60 mM Pb2+, elevated to above 80% under MICP-nHAP and to some 70% under EICP-nHAP. The findings highlight the potential of applying the nHAP-assisted biomineralization technology to Pb-containing water bodies remediation.


Subject(s)
Biomineralization , Durapatite , Lead , Urease , Water Pollutants, Chemical , Durapatite/chemistry , Lead/chemistry , Urease/metabolism , Urease/chemistry , Water Pollutants, Chemical/chemistry , Water Purification/methods , Carbonates/chemistry , Environmental Restoration and Remediation/methods
11.
Chemosphere ; 357: 141985, 2024 Jun.
Article in English | MEDLINE | ID: mdl-38614404

ABSTRACT

Carbonate radical (CO3•-) has been proved to be an important secondary radical in advanced oxidation processes due to various radical reactions involved HCO3-/CO32-. However, the roles and contributions of CO3•- in organic micropollutant degradation have not been explored systematically. Here, we quantified the impact of CO3•- on the degradation kinetics of propranolol, a representative pollutant in the UV/peroxymonosulfate (PMS) system, by constructing a steady-state radical model. Substantially, the measured values were coincident with the predictive values, and the contributions of CO3•- on propranolol degradation were the water matrix-dependent. Propranolol degradation increased by 130% in UV/PMS system containing 10 mM HCO3-, and the contribution of CO3•- was as high as 58%. Relatively high pH values are beneficial for propranolol degradation in pure water containing HCO3-, and the contributions of CO3•- also enhanced, while an inverse phenomenon was shown for the effects of propranolol concentrations. Dissolved organic matter exhibited significant scavenging effects on HO•, SO4•-, and CO3•-, substantially retarding the elimination process. The developed model successfully predicted oxidation degradation kinetics of propranolol in actual sewage, and CO3•- contribution was up to 93%, which in indicative of the important role of CO3•- in organic micropollutant removal via AOPs treatment.


Subject(s)
Carbonates , Oxidation-Reduction , Peroxides , Propranolol , Ultraviolet Rays , Water Pollutants, Chemical , Propranolol/chemistry , Water Pollutants, Chemical/chemistry , Carbonates/chemistry , Kinetics , Peroxides/chemistry , Hydrogen-Ion Concentration
12.
J Mater Chem B ; 12(20): 4945-4961, 2024 May 22.
Article in English | MEDLINE | ID: mdl-38685886

ABSTRACT

Self-activated luminescent calcium phosphate (CaP) nanoparticles, including hydroxyapatite (HA) and amorphous calcium phosphate (ACP), are promising for bioimaging and theragnostic applications in nanomedicine, eliminating the need for activator ions or fluorophores. In this study, we developed luminescent and stable citrate-functionalized carbonated ACP nanoparticles for bioimaging purposes. Our findings revealed that both the CO32- content and the posterior heating step at 400 °C significantly influenced the composition and the structural ordering of the chemically precipitated ACP nanoparticles, impacting the intensity, broadness, and position of the defect-related photoluminescence (PL) emission band. The heat-treated samples also exhibited excitation-dependent PL under excitation wavelengths typically used in bioimaging (λexc = 405, 488, 561, and 640 nm). Citrate functionalization improved the PL intensity of the nanoparticles by inhibiting non-radiative deactivation mechanisms in solution. Additionally, it resulted in an increased colloidal stability and reduced aggregation, high stability of the metastable amorphous phase and the PL emission for at least 96 h in water and supplemented culture medium. MTT assay of HepaRG cells, incubated for 24 and 48 h with the nanoparticles in concentrations ranging from 10 to 320 µg mL-1, evidenced their high biocompatibility. Internalization studies using the nanoparticles self-activated luminescence showed that cellular uptake of the nanoparticles is both time (4-24 h) and concentration (160-320 µg mL-1) dependent. Experiments using confocal laser scanning microscopy allowed the successful imaging of the nanoparticles inside cells via their intrinsic PL after 4 h of incubation. Our results highlight the potential use of citrate-functionalized carbonated ACP nanoparticles for use in internalization assays and bioimaging procedures.


Subject(s)
Calcium Phosphates , Nanoparticles , Calcium Phosphates/chemistry , Nanoparticles/chemistry , Humans , Particle Size , Luminescence , Optical Imaging , Cell Survival/drug effects , Carbonates/chemistry
13.
J Mater Chem B ; 12(18): 4509-4520, 2024 May 08.
Article in English | MEDLINE | ID: mdl-38647022

ABSTRACT

One of the key challenges in diagnosing thyroid cancer lies in the substantial percentage of indeterminate diagnoses of thyroid nodules that have undergone ultrasound-guided fine-needle aspiration (FNA) biopsy for cytological evaluation. This delays the definitive diagnosis and treatment plans. We recently demonstrated that hydroxyapatite microcalcifications (MCs) aspirated from thyroid nodules may aid nodule diagnosis based on their composition. In particular, Zn-enriched MCs have emerged as potential cancer biomarkers. However, a pertinent question remains: is the elevated Zn content within MCs a consequence of cancer, or do the Zn-enriched MCs encourage tumorigenesis? To address this, we treated the human thyroid cancer cell line MDA-T32 with synthetic MC analogs comprising hydroxyapatite crystals with varied pathologically relevant Zn fractions and assessed the cellular response. The MC analogs exhibited an irregular surface morphology similar to FNA MCs observed in cancerous thyroid nodules. These MC analogs displayed an inverse relationship between Zn fraction and crystallinity, as shown by X-ray diffractometry. The zeta potential of the non-Zn-bearing hydroxyapatite crystals was negative, which decreased once Zn was incorporated into the crystal. The MC analogs were not cytotoxic. The cellular response to exposure to these crystals was evaluated in terms of cell migration, proliferation, the tendency of the cells to form multicellular spheroids, and the expression of cancer markers. Our findings suggest that, if thyroid MCs play a role in promoting cancerous behavior in vivo, it is likely a result of the interplay of crystallinity with Zn and carbonate fractions in MCs.


Subject(s)
Calcinosis , Thyroid Neoplasms , Zinc , Humans , Thyroid Neoplasms/pathology , Thyroid Neoplasms/metabolism , Zinc/chemistry , Calcinosis/pathology , Calcinosis/metabolism , Carbonates/chemistry , Crystallization , Cell Proliferation/drug effects , Cell Line, Tumor , Durapatite/chemistry
14.
Article in English | MEDLINE | ID: mdl-38655590

ABSTRACT

The effect of temperature on the solubility of lead-bearing solid phases in water distribution systems for different water chemistry conditions remains unclear although lead concentrations are known to vary seasonally. The study objective is to explore the effect of temperature on the solubility of the lead(II) carbonate hydrocerussite under varying pH and DIC conditions. This is achieved through batch dissolution experiments conducted at multiple pHs (6-10) and DIC concentrations (20-200 mg CL-1) at temperatures ranging from 5 to 40 °C. A thermodynamic model was also applied to evaluate the model's ability to predict temperature effects on lead(II) carbonate solubility including solid phase transformations. In general, increasing temperature increased total dissolved lead at high pHs and the effect of temperature was greater for high DIC conditions, particularly for pH > 8. Temperature also influenced the pH at which the dominant lead(II) solid phase switched from hydrocerussite to cerussite (occurred between pH 7.25 to 10). Finally, the model was able to capture the overall trends observed despite thermodynamic data limitations. While this study focuses on a simple lead solid-aqueous system, findings provide important insights regarding the way in which temperature and water chemistry interact to affect lead concentrations.


Subject(s)
Carbonates , Lead , Solubility , Temperature , Lead/chemistry , Hydrogen-Ion Concentration , Carbonates/chemistry , Thermodynamics , Carbon/chemistry , Water Pollutants, Chemical/chemistry , Models, Chemical
15.
J Mater Chem B ; 12(17): 4232-4247, 2024 May 01.
Article in English | MEDLINE | ID: mdl-38601990

ABSTRACT

The design and synthesis of nano- and microcarriers for preclinical and clinical imaging are highly attractive due to their unique features, for example, multimodal properties. However, broad translation of these carriers into clinical practice is postponed due to the unknown biological reactivity of the new components used for their synthesis. Here, we have developed microcarriers (∼2-3 µm) and  nanocarriers (<200 nm) made of barium carbonate (BaCO3) for multiple imaging applications in vivo. In general, barium in the developed carriers can be used for X-ray computed tomography, and the introduction of a diagnostic isotope (99mTc) into the BaCO3 structure enables in vivo visualization using single-photon emission computed tomography. The bioimaging has shown that the radiolabeled BaCO3 nano- and microcarriers had different biodistribution profiles and tumor accumulation efficiencies after intratumoral and intravenous injections. In particular, in the case of intratumoral injection, all the types of used carriers mostly remained in the tumors (>97%). For intravenous injection, BaCO3 microcarriers were mainly localized in the lung tissues. However, BaCO3 NPs were mainly accumulated in the liver. These results were supported by ex vivo fluorescence imaging, direct radiometry, and histological analysis. The BaCO3-based micro- and nanocarriers showed negligible in vivo toxicity towards major organs such as the heart, lungs, liver, kidneys, and spleen. This study provides a simple strategy for the design and fabrication of the BaCO3-based carriers for the development of dual bioimaging.


Subject(s)
Barium , Carbonates , Tomography, Emission-Computed, Single-Photon , Animals , Mice , Carbonates/chemistry , Barium/chemistry , Tomography, X-Ray Computed , Particle Size , Nanoparticles/chemistry , Humans , Tissue Distribution
16.
Spectrochim Acta A Mol Biomol Spectrosc ; 315: 124233, 2024 Jul 05.
Article in English | MEDLINE | ID: mdl-38583394

ABSTRACT

A new phenolate-thiazole derivative (L) has been synthesized and structurally characterized.The chemo-sensing activity of L is detected by the naked eye for the aqueous carbonate anion in the pH range of 4 to 8. The selective 'turn-on' fluorescence occurs through the formation of a stable intermediate L∙CO32-(1) following the PET mechanism. The limit of detection (LOD) is found 0.18 µM based on the absorbance-based assay.The quinonoid form of bromophenol unit binds strongly with CO32- through thiazole nitrogen and hydrazinic nitrogen. Further, the selective holding of CO32- anion over other planar tetranuclear anions (e.g., SO32-, NO3-) happens with several intra and intermolecular hydrogen bonds as envisaged by the DFT/TDFT study. The formation mechanism of L∙CO32- is proposed based on experimental and theoretical studies. The biological experiments (MTT and cell imaging)reveal the non-cytotoxicity nature of L and the biocompatible uptake of L mostly in the cytoplasm at physiological pH.


Subject(s)
Anions , Carbonates , Density Functional Theory , Thiazoles , Crystallography, X-Ray , Thiazoles/chemistry , Anions/analysis , Carbonates/chemistry , Humans , Models, Molecular , Spectrometry, Fluorescence , Hydrogen-Ion Concentration , Limit of Detection , Phenols/chemistry , Phenols/analysis , Fluorescent Dyes/chemistry , Fluorescent Dyes/chemical synthesis
17.
Chemosphere ; 356: 141840, 2024 May.
Article in English | MEDLINE | ID: mdl-38582167

ABSTRACT

The extensive use of tetracyclines (TCs) has led to their widespread distribution in the environment, causing serious harm to ecosystems because of their toxicity and resistance to decomposition. Adsorption is presently the principal approach to dispose of TCs, and the development of excellent adsorbents is crucial to TC removal. Herein, a novel amorphous cobalt carbonate hydroxide (ACCH) was successfully prepared by a one-step solvothermal method, which was identified as Co(CO3)0·63(OH)0.74·0.07H2O. The ultimate adsorption capacity of ACCH for TC reaches 2746 mg g-1, and the excellent adsorption performance can be maintained over a wide pH (3.0-11.0) and temperature (10-70 °C) range. Moreover, ACCH also exhibits a wonderful adsorption performance for other organic contaminants, such as ciprofloxacin and Rhodamine B. The TC adsorption process can be reasonably described by the pseudo-second-order kinetic model, intraparticle model and Langmuir isothermal model. The experimental results in this work suggest that the excellent adsorption performance of ACCH is ascribed to the large specific surface area, alkaline characteristics and numerous functional groups of ACCH. Accordingly, this work provides a promising strategy for the development of highly-efficient adsorbents and demonstrates their application prospects in environmental remediation.


Subject(s)
Carbonates , Cobalt , Tetracycline , Cobalt/chemistry , Adsorption , Tetracycline/chemistry , Carbonates/chemistry , Kinetics , Water Pollutants, Chemical/chemistry , Nanostructures/chemistry , Hydrogen-Ion Concentration , Temperature , Anti-Bacterial Agents/chemistry
18.
Chemosphere ; 356: 141856, 2024 May.
Article in English | MEDLINE | ID: mdl-38582171

ABSTRACT

Mechanistic investigations of an environmentally friendly and easy-to-implement oxidation method in the remediation of contaminated anoxic waters, i.e. groundwater, through the sole use of oxygen for the oxygen-induced oxidation of pollutants were the focus of this work. This was achieved by the addition of O2 under anoxic conditions in the presence of ferrous iron which initiated the ferrous oxidation and the simultaneous formation of reactive •OH radicals. The involvement of inorganic ligands such as carbonates in the activation of oxygen as part of the oxidation of Fe2+ in water was investigated, too. The formation of •OH radicals, was confirmed in two different, indirect approaches by a fluorescence-based method involving coumarin as •OH scavenger and by the determination of the oxidation products of different aromatic VOCs. In the latter case, the oxidation products of several typical aromatic groundwater contaminants such as BTEX (benzene, toluene, ethylbenzene, xylenes), indane and ibuprofen, were determined. The influence of other ligands in the absence of bicarbonate and the effect of pH were also addressed. The possibility of activation of O2 in carbonate-rich water i.e. groundwater, may also potentially contribute to oxidation of groundwater contaminants and support other primary remediation techniques.


Subject(s)
Carbonates , Environmental Restoration and Remediation , Groundwater , Iron , Oxidation-Reduction , Oxygen , Water Pollutants, Chemical , Oxygen/chemistry , Water Pollutants, Chemical/chemistry , Water Pollutants, Chemical/analysis , Iron/chemistry , Groundwater/chemistry , Environmental Restoration and Remediation/methods , Carbonates/chemistry , Volatile Organic Compounds/chemistry , Hydroxyl Radical/chemistry
19.
J Hazard Mater ; 470: 134286, 2024 May 15.
Article in English | MEDLINE | ID: mdl-38615649

ABSTRACT

Microplastic hetero-aggregates are stable forms of microplastics in the aqueous environment. However, when disinfecting water containing microplastic hetero-aggregates, the response of them in water to different oxidizing agents and the effect on water quality have not been reported. Our results showed that Ca(ClO)2, K2S2O8, and sodium percarbonate (SPC) treatment could lead to the disaggregation of microplastic hetero-aggregates as well as a rise in cell membrane permeability, which caused a large amount of organic matter to be released. When the amount of oxidant dosing is insufficient, the oxidant cannot completely degrade the released organic matter, resulting in DOC, DTN, DTP and other indicators being higher than before oxidation, thus causing secondary pollution of the water body. In comparison, K2FeO4 can purify the water body stably without destroying the microplastic hetero-aggregates, but it only weakly inhibits the toxic cyanobacteria Microcystis and Pseudanabaena, which may cause cyanobacterial bloom as well as algal toxin and odorant contamination in practical application. Compared with the other oxidizers, K2S2O8 provides better inhibition of toxic cyanobacteria and has better ecological safety. Therefore, when treating microplastic-containing water bodies, we should consider both water purification and ecological safety, and select appropriate oxidant types and dosages to optimize the water treatment.


Subject(s)
Microplastics , Oxidants , Water Pollutants, Chemical , Oxidants/chemistry , Microplastics/toxicity , Microplastics/chemistry , Water Pollutants, Chemical/chemistry , Water Pollutants, Chemical/toxicity , Carbonates/chemistry , Water Purification/methods
20.
Mar Drugs ; 22(4)2024 Mar 30.
Article in English | MEDLINE | ID: mdl-38667777

ABSTRACT

Desirable characteristics of electrospun chitosan membranes (ESCM) for guided bone regeneration are their nanofiber structure that mimics the extracellular fiber matrix and porosity for the exchange of signals between bone and soft tissue compartments. However, ESCM are susceptible to swelling and loss of nanofiber and porous structure in physiological environments. A novel post-electrospinning method using di-tert-butyl dicarbonate (tBOC) prevents swelling and loss of nanofibrous structure better than sodium carbonate treatments. This study aimed to evaluate the hypothesis that retention of nanofiber morphology and high porosity of tBOC-modified ESCM (tBOC-ESCM) would support more bone mineralization in osteoblast-fibroblast co-cultures compared to Na2CO3 treated membranes (Na2CO3-ESCM) and solution-cast chitosan solid films (CM-film). The results showed that only the tBOC-ESCM retained the nanofibrous structure and had approximately 14 times more pore volume than Na2CO3-ESCM and thousands of times more pore volume than CM-films, respectively. In co-cultures, the tBOC-ESCM resulted in a significantly greater calcium-phosphate deposition by osteoblasts than either the Na2CO3-ESCM or CM-film (p < 0.05). This work supports the study hypothesis that tBOC-ESCM with nanofiber structure and high porosity promotes the exchange of signals between osteoblasts and fibroblasts, leading to improved mineralization in vitro and thus potentially improved bone healing and regeneration in guided bone regeneration applications.


Subject(s)
Calcium Phosphates , Chitosan , Coculture Techniques , Fibroblasts , Nanofibers , Osteoblasts , Osteoblasts/drug effects , Chitosan/chemistry , Fibroblasts/drug effects , Porosity , Nanofibers/chemistry , Calcium Phosphates/chemistry , Animals , Bone Regeneration/drug effects , Mice , Tissue Scaffolds/chemistry , Carbonates/chemistry , Calcification, Physiologic/drug effects
SELECTION OF CITATIONS
SEARCH DETAIL
...