The determination of underivatized chlormequat, fosetyl-aluminium and phosphonic acid residues in maize and soybean by LC-MS/MS.

In this study, a simple, rapid and sensitive method was developed for the simultaneous determination of chlormequat, fosetyl-aluminium and phosphonic acid residues in maize and soybean using liquid chromatography-triple quadrupole mass spectrometry (LC-MS/MS). Analytes were extracted with acetic acid solution, purified on an HLB column, and then filtered through a 0.2 µm hydrophilic microporous filter membrane. They were then separated on an IC column using a separation phase consisting of polyvinyl alcohol particles with quaternary ammonium groups. The mobile phase optimised with water was denoted as mobile phase A and that optimised with 200 mmol L-1 ammonium bicarbonate solution containing 0.05% ammonium hydroxide was denoted as mobile phase B. The residues were detected by tandem mass spectrometry with negative electrospray ionization in a multi-reaction monitoring mode. The correlation coefficient (R ≥ 0.997) showed good linear regressions for all analytes in water as well as in maize and soybean matrices with a wide dynamic range of 0.001 to 0.5 mg L-1 for calibration. The mean recoveries (RSDs) of the analytes were in the range 85.0-106.4% (5.5-14.9%), 81.7-109.5% (2.7-11.0%) and 74.7-104.4% (2.9-6.1%) at three concentration levels (0.05, 0.1 and 1 mg kg-1) for the interday test (n = 15). The limit of quantification (LOQ) and detection (LOD) of the method for different matrices were 0.01 and 0.003 mg kg-1, respectively. In conclusion, the established analytical approach has high sensitivity and good accuracy and precision and is suitable for monitoring chlormequat, fosetyl-aluminium and phosphonic acid residues in maize and soybean.

Development of a QuEChERS-LCMS/MS method for simultaneous estimation of tebuconazole and chlormequat chloride in wheat crop.

Tebuconazole (TBZ) and Chlormequat chloride (CCC) combination has been established as highly effective in reducing plant height of lodging prone wheat varieties. In this work, a novel analytical method employing the quick, easy, cheap, effective, rugged and safe (QuEChERS) cleanup technique and LC-MS/MS (liquid chromatography-tandem mass spectroscopy) was developed for simultaneous estimation of TBZ and CCC in wheat grains and harvest stage plant leaves. A total of 10 mL of acetonitrile and 50 mg of primary secondary amine (PSA) sorbent was consumed in the optimized QuEChERS process for leaves and grain samples. The LC-MS/MS analysis was performed using a C-18 column operating under electrospray ionization in positive mode. The QuEChERS approach achieved extraction recoveries in the acceptable range of 70%-120%, for both the compounds and was validated in terms of accuracy, precision, sensitivity and linearity. Persistence study was conducted using Lihocin (CCC 50% SL), Folicur (TBZ 25.9% EC) and their combination tank mix (Lihocin + Folicur-50% SL + 25.9% EC) applied as foliar spray twice in wheat crop (tester tall variety C-306). The results demonstrated that the developed QuEChERS-LCMS/MS is rapid and confirmatory for simultaneous quantification of both the test analytes in wheat crop.

Occurrence of the Plant Growth Regulator Chlormequat in Food May Be Due to Natural Formation: A Preliminary Mechanistic Study.

The study reports the role of choline and compounds thereof in the formation of chlormequat under thermal conditions, with emphasis on the molecular mechanism involved in the transformation. The data show the decomposition of choline to chlormequat at 200 °C in presence of chloride ions, likely by nucleophilic substitution. Furthermore, the results suggest that phosphatidylcholine, glycerophosphocholine, and phosphocholine are the effective precursors of chlormequat under sufficient thermal conditions due to their capability to degrade to choline and/or the ability of the phosphate moiety to behave as a good leaving group with respect to nucleophilic attacks. Thermal treatments (120 and 200 °C) applied to egg powder, rich in phosphatidylcholine, and wheat flour, with choline at a substantial level, suggest that less energy is required for obtaining chlormequat from phosphatidylcholine than from choline. This observation is consistent with the postulated mechanism of a nucleophilic substitution with phosphate moieties acting as better leaving groups than the hydroxyl group.

[Determination of chlormequat chloride residues in animal derived foods by high performance liquid chromatography-tandem mass spectrometry].

A method for the determination of chlormequat chloride (CCC) residues in animal derived foods by high performance liquid chromatography-tandem mass spectrometry (HPLC-MS/MS) was developed. The samples were extracted with acetonitrile containing 1% (v/v) acetic acid and defatted with n-hexane, followed by clean-up on a cationic solid phase extraction column. The analytes were separated on a Venusil MP C18(2) column (150 mm×2.1 mm, 3 µm) under a gradient elution program using acetonitrile and 0.1% (v/v) formic acid aqueous solution as the mobile phases. Then, the analytes were detected by tandem mass spectrometry using a positive electrospray ionization (ESI+) source in the multiple reaction monitoring (MRM) mode. Matrix-matched internal standard calibration curves were used for quantitative analysis. The calibration curves showed good linearity in the range of 0.200-500 µg/L for CCC, with correlation coefficients (r2) no less than 0.9993. The limit of quantification (LOQ) of the method was 0.500 µg/kg. The average recoveries of CCC in pork, beef, mutton, chicken, egg, pig kidney, beef liver, sheep kidney, chicken liver and milk matrices at spiked levels of 0.500-500 µg/kg were 93.4%-101%, and the relative standard deviations were 2.3%-8.0%. The method has less matrix interference, with high sensitivity, accuracy and reliability, and it is suitable for the quantitative detection of CCC residues in animal derived foods.

Effects of plant growth regulator application on the malting quality of barley.

BACKGROUND: Lodging can negatively affect yield and quality of barley grain. Synthetic plant growth regulators (PGRs) reduce lodging by producing shorter, thicker, and stronger stems. However, the impact of applying PGRs on malting performance of barley is not known. The objective of this work was to assess the effect of application of three PGRs (ethephon, chlormequat chloride, and trinexapac-ethyl) in combination with different seeding rates on the malting quality of barley grown in several locations and years in western Canada. RESULTS: The kernel weight in PGR-treated barley was reduced by 1.7% to 6.5% compared with the nontreated grain. Application of PGRs had no effect on the concentration of proteins and germination energy. Seeding rates significantly affected kernel weight, protein content, and germination index (GI), but no interactions between PGRs and seeding rates were observed. The smaller kernels of ethephon- and trinexapac-treated barley showed good hydration and grain modification during malting, as indicated by high levels of starch-converting enzymes, high Kolbach indices, and low levels of wort ß-glucans. Overall, the fine extract of malt from PGR-treated barley was slightly lower than that of the control malt; however, the extract reduction was statistically significant only for chlormequat- and trinexapac-treated barley. CONCLUSIONS: The application of PGRs had significant effects on kernel plumpness and kernel weight, but the effects of PGR application on the malting quality were generally small and insignificant. The decision of PGRs application on malting barley needs to be considered in combination with potential benefits of PGRs in mitigating lodging and their effects on the agronomic performance of barley. © Her Majesty the Queen in Right of Canada 2019.

Simultaneous determination of the quaternary ammonium pesticides paraquat, diquat, chlormequat, and mepiquat in barley and wheat using a modified quick polar pesticides method, diluted standard addition calibration and hydrophilic interaction liquid chromatography coupled to tandem mass spectrometry.

In this study, a modified Quick Polar Pesticides (QuPPe) method, optimized by a central composite design, was developed to determine quaternary ammonium pesticides (QUATs) residues in barley and wheat by ultra-high-performance liquid chromatographic tandem mass spectrometry (UHPLC-MS/MS) using a hydrophilic interaction chromatography (HILIC) column. Considering the high polarity of these compounds, special conditions of sample preparation and analysis are required. Different mobile phases, extraction procedure and clean-up were evaluated. An isocratic elution with aqueous solution of ammonium formate 60 mmol L-1 (pH 3.7) and acetonitrile, 40:60 (v/v), was selected. Water and acidified methanol as extraction solvent, without heating, and a clean-up with dichloromethane, chitosan and acetonitrile presented good results. The validated method presented satisfactory selectivity, linearity, matrix effect, trueness and precision, providing recoveries from 93 to 110% with RSD < 13% for barley, and 70 to 115% with RSD < 18% for wheat. The complexity of these matrices requires the calibration in matrix and the diluted standard addition calibration (DSAC) procedure has been shown to be an excellent option to compensate for the matrix effect and the losses of the analytes in the extraction. Real samples of barley and wheat were analyzed and 60% presented concentrations of paraquat above the maximum limits allowed by the European Union. The modified QuPPe method combined with DSAC and HILIC-UHPLC-MS/MS demonstrated to be an effective approach to determine QUATs in barley and wheat, and is a good alternative for routine analysis. The use of the biosorbent chitosan is effective, low cost and more ecological when compared to others conventional sorbents.

Simultaneous determination of pesticides, mycotoxins, tropane alkaloids, growth regulators, and pyrrolizidine alkaloids in oats and whole wheat grains after online clean-up via two-dimensional liquid chromatography tandem mass spectrometry.

In this study, a two-dimensional liquid chromatography tandem mass spectrometry method was developed and validated for the determination of pesticide residues and contaminants in whole wheat grains and oats. The samples were extracted with a mixture of acetonitrile and water and were injected into the two-dimensional LC-MS/MS system without any further clean-up or sample preparation. Samples were analyzed with four different matrix matched calibrations. Matrix effects were evaluated by comparing analyte signals in the respective matrix matched standard with the neat solvent standards. The final method was validated according to the current Eurachem validation guide and SANTE document. The number of successfully validated analytes throughout all three validation levels in oats and wheat, respectively, were as follows: 330 and 316 out of 370 pesticides, 6 and 13 out of 18 pyrrolizidine alkaloids and 7 out of 9 regulated mycotoxins. Moreover, both plant growth regulators mepiquat and chlormequat as well as the tropane alkaloids atropine and scopolamine met the validation criteria. The majority of pesticides showed limits of detection below 1 µg kg-1, pyrrolizidine alkaloids below 0.7 µg kg-1, tropane alkaloids below 0.2 µg kg-1, growth regulators below 0.7 µg kg-1 and mycotoxins below 8 µg kg-1 in both matrices.

Application of a molecular networking approach for clinical and forensic toxicology exemplified in three cases involving 3-MeO-PCP, doxylamine, and chlormequat.

Untargeted toxicological screening is an analytical challenge, given the high number of molecules and metabolites to be detected and the constant appearance of new psychoactive substances (NPS). The combination of liquid chromatography with high-resolution tandem mass spectrometry (HRMS/MS) in a data-dependent acquisition mode generates a large volume of high quality spectral data. Commercial software for processing MS data acquired during untargeted screening experiments usually compare measured features (mass, retention time, and fragmentation spectra) against a predefined list of analytes. However, there is a lack of tools for visualizing and organizing MS data of unknown compounds. Here, we applied molecular networking to untargeted toxicological screening. This bioinformatic tool allows the exploration and organization of MS/MS data without prior knowledge of the sample's chemical composition. The organization of spectral data is based on spectral similarity. Hence, important information can be obtained even before the annotation step. The link established between molecules enables the propagation of structural information. We applied this approach to three clinical and forensic cases with various matrices: (a) blood and a syringe content in a forensic case of death by self-injection, (b) hair segments in a case of drug-facilitated assault, and (c) urine and blood samples in a case of 3-methoxyphencyclidine intoxication. Data preprocessing with MZmine allows sample-to-sample comparison and generation of multisample molecular networks. Our present study shows that molecular networking can be a useful complement to conventional approaches for untargeted screening interpretation, for example for xenobiotics identification or NPS metabolism elucidation.

Determination of chlormequat and mepiquat residues and their dissipation rates in tomato cultivation matrices by ultra-performance liquid chromatography-tandem mass spectrometry.

This study described the development and validation of a simple, rapid, specific and sensitive method for detecting chlormequat chloride (CQ) and mepiquat chloride (MQ) residues in tomato cultivation matrices covering soil, water, seedling samples. The dissipation rates of CQ and MQ in tomato cultivation matrices were also determined in this study. A Hydrophilic Interaction Liquid Chromatography (HILIC) column was used for chromatographic separation. A triple quadrupole mass spectrometer equipped with an electrospray ionisation source in positive ion mode by multiple reaction monitoring was used for detection. Soil samples were extracted with accelerated solvent extraction (ASE) and cleaned up with WCX phase extraction column; water samples were extracted with WCX phase extraction column; seedling samples were extracted with methanol-ammonium acetate solution. LODs and LOQs of CQ and MQ were 0.02µg/kg and 0.1µg/kg in soil samples, 0.005ng/mL and 0.02ng/mL in water samples, and 0.05µg/kg and 1.0µg/kg in seedling samples, respectively. The mean recovery rate of CQ in soil, water and seedling samples ranged from 76.98% to 111.60%. While the mean recovery rate of MQ in soil, water and seedling samples ranged from 96.90% to 105.40%. The fastest to the slowest metabolising rates of CQ and MQ were as follows: soil samples>seedling samples>water samples. In conclusion, this study provided a new potential method for detecting CQ and MQ in tomato cultivation matrices using ultra-performance liquid chromatography-tandem mass spectrometry.

Suicide by self-injection of chlormequat trademark C5SUN(®).

Chlormequat is a quaternary ammonium used as plant growth regulating agent. We report here the first suicide case involving a 45 year-old farmer man who intentionally self-injected C5SUN(®), containing chlormequat and choline. An original liquid chromatography high resolution mass spectrometry method (LC-HR-MS), using a hybrid quadrupole-orbitrap mass spectrometer, was developed for qualitative and quantitative analysis of chlormequat in different biological matrices. Toxicological analyses of post-mortem samples highlighted the presence of chlormequat in the blood (2.25mg/L) and the urine (4.45mg/L), in addition to ethanol impregnation blood (1.15g/L). The route of administration (subcutaneous injection) was confirmed by the detection of chlormequat in the abdominal fat sample (chlormequat: 10.04mg/g) taken from the traumatic injury location, as well as in the syringe found at the death scene, close to the victim's body. Based on the results of these post-mortem investigations, the cause of death was determined to be consecutive to cardiac dysrhythmia and cardiac arrest following chlormequat self-injection.

Comparisons of metabolic and physiological changes in rats following short term oral dosing with pesticides commonly found in food.

¹H Nuclear Magnetic Resonance spectroscopy has been used to profile urinary metabolites in male Fischer F344 rats in order to assess the metabolic changes induced by oral exposure to two benzimidazole fungicides (carbendazim and thiabendazole) and two bipyridyllium herbicides (chlormequat and mepiquat). Exposure levels were selected to be lower than those expected to cause overt signs of toxicity. We then compared the sensitivity of the metabolomics approach to more traditional methods of toxicity assessment such as the measurement of growth and organ weights. Separate, acute exposure experiments were conducted for each pesticide to identify potential metabolic markers of exposure across four doses (and a control). Growth, organ weights and feeding/drinking rates were not significantly affected by any compounds at any dose levels tested. In contrast, metabolic responses were detected within 8 and 24h for chlormequat and mepiquat, and after 24h for carbendazim and thiabendazole. These results demonstrate the potential for the use of metabolomics in food toxicity testing.

Rapid determination of chlormequat in meat by dispersive solid-phase extraction and hydrophilic interaction liquid chromatography (HILIC)-electrospray tandem mass spectrometry.

A rapid method for analyzing trace levels of chlormequat (CQ) in meat samples by hydrophilic interaction liquid chromatography (HILIC)-electrospray tandem mass spectrometry was developed. The samples were extracted with acetonitrile, followed by a rapid cleanup through a dispersive solid-phase extraction (DSPE) technique with octadecyl (C18) DSPE sorbents. The chromatographic separation was achieved within 6 min using a HILIC column with 10 mM ammonium acetate and 0.1% (v/v) formic acid in water/acetonitrile (v/v, 40:60) as the mobile phase. Quantification was performed using a matrix-matched calibration curve, which was linear in the range of the 0.05-100 µg/L. The limit of detection (LOD) was estimated at 0.03 µg/kg for CQ on the basis of a peak to peak signal noise (S/N = 3). The limit of quantification (LOQ) was 0.1 µg/kg on the basis of the lowest spiked concentration with suitable precision and accuracy. The average recovery of CQ in spiked meat samples was 86.4-94.7% at 2, 20, and 200 µg/kg. Finally, this method was applied to determine CQ in the livestock and poultry meats purchased from markets in Beijing in 2011. CQ was detected in all 12 samples, and the concentration was 0.4-636.0 µg/kg. Concentrations in a chicken sample (636.0 µg/kg) and a goat meat sample (486.0 µg/kg) were found to be 15.9 and 2.43 times the corresponding Codex maximum residue limits, respectively.

[Simultaneous determination of chlormequat chloride and mepiquat chloride in plants by mobile phase ion chromatography].

Ion-pair reagent was used as mobile phase for the simultaneous separation of chlormequat chloride and mepiquat chloride in plants. The rapid separation was performed on a Dionex IonPac NG1 guard column and a Dionex IonPac NS1 analytical column using 1.0 mL/min of the eluent mixture of 1.00 mmol/L nonafluoropentanoic acid (as ion-pair reagent) and 7% acetonitrile, and the detection was achieved by a suppressed conductivity detector. The method provided good resolution of the analyte peaks without any interference. The detection limits of chlormequat chloride and mepiquat chloride were 0.154 6 mg/L and 0.171 4 mg/L, respectively. The linear calibration curves were obtained in the range of 1 - 100 mg/L. The mean recoveries in the ranges of 96.06% - 104.6% for chlormequat chloride and 98.53% - 103.7% for mepiquat chloride were obtained in real samples. The method requires only simple sample preparation and the technique is suitable for routine quality control analysis.

An improved method for analyzing chlormequat and mepiquat in source waters by solid-phase extraction and liquid chromatography-mass spectrometry.

A liquid chromatography-mass spectrometry (LC-MS) method for the identification and quantification of chlormequat (CQ) and mepiquat (MQ) in source waters with high sensitivity and specificity was established using WCX cartridges (150 mg/6 mL) for pre-concentration of the samples and using the CAPCELL PAK CR 1:4 (2.0 mm×150 mm 5 µm, SCX:C18=1:4) column containing strong cationic exchange resins and C18 for separation. The method could solve the problem for pre-concentrating ionic compounds from water samples and avoid the MS instrument fouling problem accompanied with the use of ion-pair reagents. After the optimization of analytical conditions, quantification was achieved in the positive electrospray ionization mode using selected ion monitoring. The samples were analyzed with multi-channel mode with quantification performed at 30 V cone voltage to ascertain the sensitivity and qualitative analysis performed at 60 V cone voltage simultaneously. The method detection limits (MDLs) of CQ and MQ in source water were determined to be 14 and 22 ng L(-1). Finally, the method was used to quantify CQ and MQ in several source waters, which gave a level ranging from below the quantitation limit to 28 ng L(-1).

Fate and transport of chlormequat in subsurface environments.

BACKGROUND, AIM AND SCOPE: Chlormequat (Cq) is a plant growth regulator used throughout the world. Despite indications of possible effects of Cq on mammalian health and fertility, little is known about its fate and transport in subsurface environments. The aim of this study was to determine the fate of Cq in three Danish subsurface environments, in particular with respect to retardation of Cq in the A and B horizons and the risk of leaching to the aquatic environment. The study combines laboratory fate studies of Cq sorption and dissipation with field scale monitoring of the concentration of Cq in the subsurface environment, including artificial drains. MATERIALS AND METHODS: For the laboratory studies, soil was sampled from the A and B horizons at three Danish field research stations-two clayey till sites and one coarse sandy site. Adsorption and desorption were described by means of the distribution coefficient (K (d)) and the Freundlich adsorption coefficient (K (F,ads)). The dissipation rate was estimated using soil sampled from the A horizon at the three sites. Half life (DT(50)) was calculated by approximation to first-order kinetics. A total of 282 water samples were collected at the sites under the field monitoring study- groundwater from shallow monitoring screens located 1.5-4.5 m b.g.s. at all three sites as well as drainage water from the two clayey sites and porewater from suction cups at the sandy site, in both cases from 1 m b.g.s. The samples were analysed using LC-MS/MS. The field monitoring study was supported by hydrological modelling, which provided an overall water balance and a description of soil water dynamics in the vadose zone. RESULTS: The DT(50) of Cq from the A horizon ranged from 21 to 61 days. The Cq concentration-dependant distribution coefficient (K (d)) ranged from 2 to 566 cm(3)/g (median 18 cm(3)/g), and was lowest in the sandy soil (both the A and B horizons). The K (F,ads) ranged from 3 to 23 (microg(1 - 1/n ) (cm(3))(1/n) g(-1)) with the exponent (1/n) ranging from 0.44 to 0.87, and was lowest in the soil from the sandy site. Desorption of Cq was very low for the soil types investigated (<10%w). Cq in concentrations exceeding the detection limit (0.01 microg/L) was only found in two of the 282 water samples, the highest concentration being 0.017 microg/L. DISCUSSION: That sorption was highest in the clayey till soils is attributable to the composition of the soil, the soil clay and iron content being the main determinant of Cq sorption in both the A and B horizons of the subsurface environment. Cq was not detected in concentrations exceeding the detection limit in either the groundwater or the porewater at the sandy site. The only two samples in which Cq was detected were drainage water samples from the two clayey till sites. The presence of Cq here was probably attributable to the hydrogeological setting as water flow at the two clayey till sites is dominated by macropore flow and less by the flow in the low permeability matrix. In contrast, water flow at the sandy site is dominated by matrix flow in the high permeability matrix, with negligible macropore flow. Given the characteristics of these field sites, Cq adsorption and desorption can be expected to be controlled by the clay composition and content and the iron content. Combining these observations with the findings of the sorption and dissipation studies indicates that the key determinant of Cq retardation and fate in the soil is sorption characteristics and bioavailability. CONCLUSIONS: The leaching risk of Cq was negligible at the clayey till and sandy sites investigated. The adsorption and desorption experiments indicated that absorption of Cq was high at all three sites, in particular at the clayey till sites, and that desorption was generally very limited. The study indicates that leaching of Cq to the groundwater is hindered by sorption and dissipation. The detection of Cq in drainage water at the clayey till sites and the evidence for rapid transport through macropores indicate that heavy precipitation events may cause pulses of Cq. RECOMMENDATIONS AND PERSPECTIVES: The present study is the first to indicate that the risk of Cq leaching to the groundwater and surface water is low. Prior to any generalisation of the present results, the fate of Cq needs to be studied in other soil types, application regimes and climatic conditions to determine the Cq retardation capacity of the soils. The study identifies bioavailability and heavy precipitation events as important factors when assessing the risk of Cq contamination of the aquatic environment. The possible effects of future climate change need to be considered when assessing whether or not Cq poses an environmental risk.

Chlormequat residues and dissipation rates in cotton crops and soil.

A simple and reliable analytical method for chlormequat residues in cotton and soil was established in this study. The residual levels and dissipation rates of chlormequat in cotton crops and soil were determined by High Performance Liquid Chromatography-Mass Spectroscopy (HPLC-MS). The limit of quantification (LOQ) was 0.05, 0.1, 0.1mg/kg for soil, cotton seeds and cotton leaves, respectively. The mean half-life of chlormequat was 4.47 days in cotton plants and was 4.34 days in soil. The final residues of chlormequat in cotton seeds were below 0.5mg/kg (the MRL of China), while the chlormequat residues could not be detected in soil. Low residues in cotton seed and soil suggest that this pesticide may be safe to use under the recommended dosage.

Dissipation and residues of chlormequat in wheat and soil.

A specific, sensitive method was developed for the analysis of chlormequat in wheat and soil by high performance chromatography/mass spectrometry. The fortified recoveries of soil were from 75.08% to 96.55%, with RSD 3.34%-15.18%, the limit of detection of the analytical method was 0.05 ng at a signal-to-noise ratio of 3, and the limit of quantification was 0.05, 0.1, 0.5 mg/kg for soil, wheat plants and wheat grain, respectively. The degradation dynamics and final residues of chlormequat in Beijing and Changchun were investigated. The half-life of chlormequat in wheat plants were 3.15 days in Beijing and 4.56 days in Changchun, while the half-life in soil was 3.88 days in Beijing and 4.51 days in Changchun. The final residues of chlormequat in soil were not detectable, and the final residues of chlormequat in wheat grain were below 0.50 mg/kg except for 3.51 mg/kg from high dosage plot of Changchun. The fact that all the final residues were below 5 mg/kg (GB2763 in National standards of the People's Republic of China, maximum residue limits for pesticide in food, Beijing, 2005) suggested that chlormequat could be safely used in wheat crops with the suitable dosage and application.

Analysis of chlormequat and mepiquat by hydrophilic interaction chromatography coupled to tandem mass spectrometry in food samples.

In this work a LC-MS/MS method for the determination of two quaternary ammonium growth regulators (chlormequat and mepiquat) in food is reported. The separation was based on hydrophilic interaction liquid chromatography (HILIC) without the use of ion-pair reagents. A gradient elution of acetonitrile and formic acid/ammonium formate buffer from 60 to 40% acetonitrile was enough to achieve a resolution >1.5 in less than 4.0min. The HILIC system was coupled to a triple quadrupole mass spectrometer equipped with a heated electrospray probe (H-ESI) providing sub-pg LODs in SRM mode. A straightforward sample treatment (SPE C18 clean-up) was enough to provide MLODs at low ppb levels when analysing a range of food samples that covered different kinds of matrices such as fresh fruit, vegetables, fruit juices, baby food, bread, coffee and beer. Chlormequat was found in seven samples (0.8-126ng/g) but mepiquat was only detected in bread and coffee samples (0.9-166ng/g).

Analysis of the plant growth regulator chlormequat in soil and water by means of liquid chromatography-tandem mass spectrometry, pressurised liquid extraction, and solid-phase extraction.

We present a new, precise and accurate method for quantitative analysis of chlormequat in soil and aqueous matrices. The method, which is based on LC-MS/MS, pressurised liquid extraction and solid-phase extraction, is eminently suitable for studying the fate of chlormequat in the soil environment. The limit of detection is 0.003-0.008 microg/L for rainwater, surface water and groundwater and 0.07-0.4 microg/kg for soil. In water samples amended to 0.04 microg/L, precision is better than 10%. The residual content of chlormequat in three agricultural topsoils analysed 4 months after its application was 23-55 microg/kg (12-23% of the amount applied). No trace of chlormequat was detected in groundwater from 66 water supply wells located in rural areas treated with chlormequat.

Determination of chlormequat in pig serum and sow milk by LC-MS/MS.

Chlormequat is a plant growth regulator widely used on cereals, and there is general concern that it may impair human fertility. A LC-MS/MS method for the analysis of chlormequat in milk and serum was developed and validated in connection with an investigation on the effect of chlormequat on pig reproduction. Validation of the method was based on recovery tests at three spiking levels, determined as double determinations and repeated at least four times. Samples were extracted with methanol-water-acetic acid, centrifuged, filtrated and determined by LC-MS/MS. The mean recoveries were in the range 80-110%, and the LOD was 0.2 ng/g for serum and 0.3 ng/g for milk. The values for repeatability and reproducibility were within 2/3 of the limits given by the Horwitz equation. Samples of pig serum (59) and sow milk (27) were analyzed using the method. Chlormequat was determined in four milk samples in the range of 0.4 ng/g to 1.2 ng/g and in all serum samples in the range of 0.2 ng/g-4.0 ng/g.