Establishment of soil strength in a nourished wetland using thin layer placement of dredged sediment.

Coastal wetlands are experiencing accelerated rates of fragmentation and degradation due to sea-level rise, sediment deficits, subsidence, and salt-water intrusion. This reduces their ability to provide ecosystem benefits, such as wave attenuation, habitat for migratory birds, and a sink for carbon and nitrogen cycles. A deteriorated back barrier wetland in New Jersey, USA was nourished through thin layer placement (TLP) of dredged sediment in 2016. A field investigation was conducted in 2019 using a cone penetrometer (CPT) to quantify the establishment of soil strength post sediment nourishment compared to adjacent reference sites in conjunction with traditional wetland performance measures. Results show that the nourished area exhibited weaker strengths than the reference sites, suggesting the root system of the vegetation is still establishing. The belowground biomass measurements correlated to the CPT strength measurements, demonstrating that shear strength measured from the cone penetrometer could serve as a surrogate to monitor wetland vegetation trajectories. In addition, heavily trafficked areas underwent compaction from heavy equipment loads, inhibiting the development of vegetation and highlighting how sensitive wetlands are to anthropogenic disturbances. As the need for more expansive wetland restoration projects grow, the CPT can provide rapid high-resolution measurements across large areas supplying government and management agencies with vital establishment trajectories.

Is a Linear or a Walkabout Protocol More Efficient When Using a Rover to Choose Biologically Relevant Samples in a Small Region of Interest?

We conducted a field test at a potential Mars analog site to provide insight into planning for future robotic missions such as Mars 2020, where science operations must facilitate efficient choice of biologically relevant sampling locations. We compared two data acquisition and decision-making protocols currently used by Mars Science Laboratory: (1) a linear approach, where sites are examined as they are encountered and (2) a walkabout approach, in which the field site is first examined with remote rover instruments to gain an understanding of regional context followed by deployment of time- and power-intensive contact and sampling instruments on a smaller subset of locations. The walkabout method was advantageous in terms of both the time required to execute and a greater confidence in results and interpretations, leading to enhanced ability to tailor follow-on observations to better address key science and sampling goals. This advantage is directly linked to the walkabout method's ability to provide broad geological context earlier in the science analysis process. For Mars 2020, and specifically for small regions to be explored (e.g., <1 km2), we recommend that the walkabout approach be considered where possible, to provide early context and time for the science team to develop a coherent suite of hypotheses and robust ways to test them.

Short-range propagation characteristics of airgun pulses during marine seismic reflection surveys.

Marine seismic reflection surveys use airguns to generate repetitive high energy sound signals to image the structure of the seafloor. To better mitigate against the impact of airgun pulses on marine mammals, safety criteria are defined to ensure marine mammals are not exposed to high levels of acoustic energy. Accurate prediction of the sound received levels away from the airguns is required for conducting effective marine mammal monitoring. In this study, measurements by a horizontal hydrophone array towed by the R/V Marcus G. Langseth behind a seismic source array have been used to characterize short-range propagation of airgun pulses and predict the acoustic energy radiated from a seismic source. Data from the Cascadia Open-Access Seismic Transects seismic reflection survey are used to train a linear regression (LR) and a random forest (RF) model to estimate sound exposure levels (SELs) in short ranges from the airguns. Results show that the LR model does not account for all the variance in data. However, the RF model is able to estimate the SELs with a high coefficient of determination and a low mean squared error. Results from the LR model show that the rate at which SELs decrease in deep water does not match either of the cylindrical or spherical spreading models. Simulations are undertaken to understand this inconsistency as well as the effect of hydrophone group-averaging on data recorded by a seismic hydrophone array.

New Experimental Equipment Recreating Geo-Reservoir Conditions in Large, Fractured, Porous Samples to Investigate Coupled Thermal, Hydraulic and Polyaxial Stress Processes.

Use of the subsurface for energy resources (enhanced geothermal systems, conventional and unconventional hydrocarbons), or for storage of waste (CO2, radioactive), requires the prediction of how fluids and the fractured porous rock mass interact. The GREAT cell (Geo-Reservoir Experimental Analogue Technology) is designed to recreate subsurface conditions in the laboratory to a depth of 3.5 km on 200 mm diameter rock samples containing fracture networks, thereby enabling these predictions to be validated. The cell represents an important new development in experimental technology, uniquely creating a truly polyaxial rotatable stress field, facilitating fluid flow through samples, and employing state of the art fibre optic strain sensing, capable of thousands of detailed measurements per hour. The cell's mechanical and hydraulic operation is demonstrated by applying multiple continuous orientations of principal stress to a homogeneous benchmark sample, and to a fractured sample with a dipole borehole fluid fracture flow experiment, with backpressure. Sample strain for multiple stress orientations is compared to numerical simulations validating the operation of the cell. Fracture permeability as a function of the direction and magnitude of the stress field is presented. Such experiments were not possible to date using current state of the art geotechnical equipment.

Laser-induced plasma spectroscopy (LIPS): use of a geological tool in assessing bone mineral content.

Bone may be similar to geological formulations in many ways. Therefore, it may be logical to apply laser-based geological techniques in bone research. The mineral and element oxide composition of bioapatite can be estimated by mathematical models. Laser-induced plasma spectrometry (LIPS) has long been used in geology. This method may provide a possibility to determine the composition and concentration of element oxides forming the inorganic part of bones. In this study, we wished to standardize the LIPS technique and use mathematical calculations and models in order to determine CaO distribution and bone homogeneity using bovine shin bone samples. We used polished slices of five bovine shin bones. A portable LIPS instrument using high-power Nd++YAG laser pulses has been developed (OpLab, Budapest). Analysis of CaO distribution was carried out in a 10 × 10 sampling matrix applying 300-µm sampling intervals. We assessed both cortical and trabecular bone areas. Regions of interest (ROI) were determined under microscope. CaO peaks were identified in the 200-500 nm wavelength range. A mathematical formula was used to calculate the element oxide composition (wt%) of inorganic bone. We also applied two accepted mathematical approaches, the Bartlett's test and frequency distribution curve-based analysis, to determine the homogeneity of CaO distribution in bones. We were able to standardize the LIPS technique for bone research. CaO concentrations in the cortical and trabecular regions of B1-5 bones were 33.11 ± 3.99% (range 24.02-40.43%) and 27.60 ± 7.44% (range 3.58-39.51%), respectively. CaO concentrations highly corresponded to those routinely determined by ICP-OES. We were able to graphically demonstrate CaO distribution in both 2D and 3D. We also determined possible interrelations between laser-induced craters and bone structure units, which may reflect the bone structure and may influence the heterogeneity of CaO distributions. By using two different statistical methods, we could confirm if bone samples were homogeneous or not with respect to CaO concentration distribution. LIPS, a technique previously used in geology, may be included in bone research. Assessment of element oxide concentrations in the inorganic part of bone, as well as mathematical calculations may be useful to determine the content of CaO and other element oxides in bone, further analyze bone structure and homogeneity and possibly apply this research to normal, as well as diseased bones.

Utilizing the R/V Marcus G. Langseth's streamer to measure the acoustic radiation of its seismic source in the shallow waters of New Jersey's continental shelf.

Shallow water marine seismic surveys are necessary to understand a range of Earth processes in coastal environments, including those that represent major hazards to society such as earthquakes, tsunamis, and sea-level rise. Predicting the acoustic radiation of seismic sources in shallow water, which is required for compliance with regulations designed to limit impacts on protected marine species, is a significant challenge in this environment because of variable reflectivity due to local geology, and the susceptibility of relatively small bathymetric features to focus or shadow acoustic energy. We use data from the R/V Marcus G. Langseth's towed hydrophone streamer to estimate the acoustic radiation of the ship's seismic source during a large survey of the shallow shelf off the coast of New Jersey. We use the results to estimate the distances from the source to acoustic levels of regulatory significance, and use bathymetric data from the ship's multibeam system to explore the relationships between seafloor depth and slope and the measured acoustic radiation patterns. We demonstrate that existing models significantly overestimate mitigation radii, but that the variability of received levels in shallow water suggest that in situ real-time measurements would help improve these estimates, and that post-cruise revisions of received levels are valuable in accurately determining the potential acoustic impact of a seismic survey.

Analysis of spectra from portable handheld gamma-ray spectrometry for terrain comparative assessment.

Geological characteristics can have impacts on societal development by, e.g., geotechnical issues and radiological hazard levels. Due to urban sprawl, there is an increasing need for detailed geological assessment. In this work are analysed data from portable handheld gamma-ray spectra (K, eU and eTh) obtained in granitic and Silurian metaclastic outcrops as well as in an profile, roughly N-S, on soil covered terrains transecting a mapped contact between these rock types (the profile's northern extremity is at locations mapped as granite). Estimations from gamma-ray spectra were studied by univariate and multivariate analyses. K, eU and eTh values were higher on granite in relation to Silurian metaclastic rocks. The northern extremity of the profile showed clearly higher contents of eTh and this contrast was supported by univariate statistical tools (normality plot and Wilk-Shapiro test; boxplots). A ternary plot with the contribution of the elements to gamma-ray absorbed dose showed the separation of granite from Silurian metaclastic rocks with the former being nearer the eTh vertex. The points in the northern extremity of the profile are nearer the eTh vertex than the other points on the profile. These visual suggestions were supported by hierarchical cluster analysis, which was able to differentiate between granite and metaclastic outcrops and separate portions of the profile located on different terrains. Portable gamma-ray spectrometry showed, hence, the potential to distinguish granite and metaclastic terrains at a scale useful for engineering works. These results can also be useful for a first comparative zoning of radiological hazards (which are higher for granite).

Effects of multiple impulses from a seismic air gun on bottlenose dolphin hearing and behavior.

To investigate the auditory effects of multiple underwater impulses, hearing thresholds were measured in three bottlenose dolphins before and after exposure to 10 impulses produced by a seismic air gun. Thresholds were measured at multiple frequencies using both psychophysical and electrophysiological (auditory evoked potential) methods. Exposures began at relatively low levels and gradually increased over a period of several months. The highest exposures featured peak sound pressure levels from 196 to 210 dB re 1 µPa, peak-peak sound pressure levels of 200-212 dB re 1 µPa, and cumulative (unweighted) sound exposure levels from 193 to 195 dB re 1 µPa(2)s. At the cessation of the study, no significant increases were observed in psychophysical thresholds; however, a small (9 dB) shift in mean auditory evoked potential thresholds, accompanied by a suppression of the evoked potential amplitude function, was seen in one subject at 8 kHz. At the highest exposure condition, two of the dolphins also exhibited behavioral reactions indicating that they were capable of anticipating and potentially mitigating the effects of impulsive sounds presented at fixed time intervals.

Airgun inter-pulse noise field during a seismic survey in an Arctic ultra shallow marine environment.

Offshore oil and gas exploration using seismic airguns generates intense underwater pulses that could cause marine mammal hearing impairment and/or behavioral disturbances. However, few studies have investigated the resulting multipath propagation and reverberation from airgun pulses. This research uses continuous acoustic recordings collected in the Arctic during a low-level open-water shallow marine seismic survey, to measure noise levels between airgun pulses. Two methods were used to quantify noise levels during these inter-pulse intervals. The first, based on calculating the root-mean-square sound pressure level in various sub-intervals, is referred to as the increment computation method, and the second, which employs the Hilbert transform to calculate instantaneous acoustic amplitudes, is referred to as the Hilbert transform method. Analyses using both methods yield similar results, showing that the inter-pulse sound field exceeds ambient noise levels by as much as 9 dB during relatively quiet conditions. Inter-pulse noise levels are also related to the source distance, probably due to the higher reverberant conditions of the very shallow water environment. These methods can be used to quantify acoustic environment impacts from anthropogenic transient noises (e.g., seismic pulses, impact pile driving, and sonar pings) and to address potential acoustic masking affecting marine mammals.

Sound source localization technique using a seismic streamer and its extension for whale localization during seismic surveys.

Marine seismic surveys are under increasing scrutiny because of concern that they may disturb or otherwise harm marine mammals and impede their communications. Most of the energy from seismic surveys is low frequency, so concerns are particularly focused on baleen whales. Extensive mitigation efforts accompany seismic surveys, including visual and acoustic monitoring, but the possibility remains that not all animals in an area can be observed and located. One potential way to improve mitigation efforts is to utilize the seismic hydrophone streamer to detect and locate calling baleen whales. This study describes a method to localize low frequency sound sources with data recoded by a streamer. Beamforming is used to estimate the angle of arriving energy relative to sub-arrays of the streamer which constrains the horizontal propagation velocity to each sub-array for a given trial location. A grid search method is then used to minimize the time residual for relative arrival times along the streamer estimated by cross correlation. Results from both simulation and experiment are shown and data from the marine mammal observers and the passive acoustic monitoring conducted simultaneously with the seismic survey are used to verify the analysis.

The microwave induced plasma with optical emission spectrometry (MIP-OES) in 23 elements determination in geological samples.

The article presents the optimisation, validation and application of the microwave induced plasma optical emission spectrometry (MIP-OES) dedicated for a routine determination of Ag, Al, B, Ba, Bi, Ca, Cd, Cr, Cu, Fe, Ga, In, K, Li, Mg, Mn, Mo, Na, Ni, Pb, Sr, Tl, Zn, in the geological samples. The three procedures of sample preparation has been proposed: sample digestion with the use of hydrofluoric acid for determination of total concentration of elements, extraction by aqua regia for determination of the quasi-total element concentration and extraction by hydrochloric acid solution to determine contents of the elements in acid leachable fraction. The detection limits were on the level 0.001-0.121 mg L(-1) (from 0.010-0.10 to 1.2-12 mg kg(-1) depend on the samples preparation procedure); the precision: 0.20-1.37%; accuracy 85-115% (for recovery for certified standards materials analysis and parallel analysis by independent analytical techniques: X-ray fluorescence (XRF) and flame absorption spectrometry (FAAS)). The conformity of the results obtained by MIP-OES analytical procedures with the results obtained by XRF and FAAS analysis allows to propose the procedures for studies of elemental composition of the fraction of the geological samples. Additionally, the MIP-OES technique is much less expensive than ICP techniques and much less time-consuming than AAS techniques.

Experimental analyses of the major parameters affecting the intensity of outbursts of coal and gas.

With an increase in mining depth and production, the intensity and frequency of outburst of coal and gas have a tendency to increase. Estimating the intensity of outbursts of coal and gas plays an important role because of its relation with the risk value. In this paper, we described the semiquantitative relations between major parameters and intensity of outburst based on physical experiments. The results showed increment of geostress simulated by horizontal load (from 1.4, 2.4, 3.2, to 3.4 MPa) or vertical load (from 2, 3, 3.6, to 4 MPa) improved the relative intensity rate (3.763-7.403% and 1.273-7.99%); the increment of porosity (from 1.57, 2.51, 3, to 3.6%) improved the relative intensity rate from 3.8 to 13.8%; the increment of gas pressure (from 0, 0.5, 0.65, 0.72, 1, to 1.5 Mpa) induced the relative intensity rate to decrease from 38.22 to 0%; the increment of water content (from 0, 2, 4, to 8%) caused the relative intensity rate to drop from 5.425 to 0.5%. Furthermore, sensitivity and range analysis evaluates coupled factors affecting the relative intensity. In addition, the distinction with initiation of outburst of coal and gas affected by these parameters is discussed by the relative threshold of gas content rate.

Field demonstration of an instrument performing automatic classification of geologic surfaces.

This work presents a method with which to automate simple aspects of geologic image analysis during space exploration. Automated image analysis on board the spacecraft can make operations more efficient by generating compressed maps of long traverses for summary downlink. It can also enable immediate automatic responses to science targets of opportunity, improving the quality of targeted measurements collected with each command cycle. In addition, automated analyses on Earth can process large image catalogs, such as the growing database of Mars surface images, permitting more timely and quantitative summaries that inform tactical mission operations. We present TextureCam, a new instrument that incorporates real-time image analysis to produce texture-sensitive classifications of geologic surfaces in mesoscale scenes. A series of tests at the Cima Volcanic Field in the Mojave Desert, California, demonstrated mesoscale surficial mapping at two distinct sites of geologic interest.

Displacement parameter inversion for a novel electromagnetic underground displacement sensor.

Underground displacement monitoring is an effective method to explore deep into rock and soil masses for execution of subsurface displacement measurements. It is not only an important means of geological hazards prediction and forecasting, but also a forefront, hot and sophisticated subject in current geological disaster monitoring. In previous research, the authors had designed a novel electromagnetic underground horizontal displacement sensor (called the H-type sensor) by combining basic electromagnetic induction principles with modern sensing techniques and established a mutual voltage measurement theoretical model called the Equation-based Equivalent Loop Approach (EELA). Based on that work, this paper presents an underground displacement inversion approach named "EELA forward modeling-approximate inversion method". Combining the EELA forward simulation approach with the approximate optimization inversion theory, it can deduce the underground horizontal displacement through parameter inversion of the H-type sensor. Comprehensive and comparative studies have been conducted between the experimentally measured and theoretically inversed values of horizontal displacement under counterpart conditions. The results show when the measured horizontal displacements are in the 0-100 mm range, the horizontal displacement inversion discrepancy is generally tested to be less than 3 mm under varied tilt angles and initial axial distances conditions, which indicates that our proposed parameter inversion method can predict underground horizontal displacement measurements effectively and robustly for the H-type sensor and the technique is applicable for practical geo-engineering applications.

Hydraulic tomography offers improved imaging of heterogeneity in fractured rocks.

Fractured rocks have presented formidable challenges for accurately predicting groundwater flow and contaminant transport. This is mainly due to our difficulty in mapping the fracture-rock matrix system, their hydraulic properties and connectivity at resolutions that are meaningful for groundwater modeling. Over the last several decades, considerable effort has gone into creating maps of subsurface heterogeneity in hydraulic conductivity (K) and specific storage (Ss ) of fractured rocks. Developed methods include kriging, stochastic simulation, stochastic inverse modeling, and hydraulic tomography. In this article, I review the evolution of various heterogeneity mapping approaches and contend that hydraulic tomography, a recently developed aquifer characterization technique for unconsolidated deposits, is also a promising approach in yielding robust maps (or tomograms) of K and Ss heterogeneity for fractured rocks. While hydraulic tomography has recently been shown to be a robust technique, the resolution of the K and Ss tomograms mainly depends on the density of pumping and monitoring locations and the quality of data. The resolution will be improved through the development of new devices for higher density monitoring of pressure responses at discrete intervals in boreholes and potentially through the integration of other data from single-hole tests, borehole flowmeter profiling, and tracer tests. Other data from temperature and geophysical surveys as well as geological investigations may improve the accuracy of the maps, but more research is needed. Technological advances will undoubtedly lead to more accurate maps. However, more effort should go into evaluating these maps so that one can gain more confidence in their reliability.

Compressive geoacoustic inversion using ambient noise.

Surface generated ambient noise can be used to infer sediment properties. Here, a passive geoacoustic inversion method that uses noise recorded by a drifting vertical array is adopted. The array is steered using beamforming to compute the noise arriving at the array from various directions. This information is used in two different ways: Coherently (cross-correlation of upward/downward propagating noise using a minimum variance distortionless response fathometer), and incoherently (bottom loss vs frequency and angle using a conventional beamformer) to obtain the bottom properties. Compressive sensing is used to invert for the number of sediment layer interfaces and their depths using coherent passive fathometry. Then the incoherent bottom loss estimate is used to refine the sediment thickness, sound speed, density, and attenuation values. Compressive sensing fathometry enables automatic determination of the number of interfaces. It also tightens the sediment thickness priors for the incoherent bottom loss inversion which reduces the search space. The method is demonstrated on drifting array data collected during the Boundary 2003 experiment.

Experimental study on monitoring CO2 sequestration by conjoint analysis of the P-wave velocity and amplitude.

CO2 sequestration has been considered to be one of the most straightforward carbon management strategies for industrial CO2 emission. Monitoring of the CO2 injection process is one of the best ways to make sure the safety storage but is also a major challenge in CO2 geological sequestration. Previous field and laboratory researches have shown that seismic methods are among the most promising monitoring methods because of the obvious reduction in P-wave velocities caused by CO2 injection. However, as CO2 injection continues, the P-wave velocity becomes increasingly insensitive according to the pilot projects when CO2 saturation is higher than 20-40%. Therefore, the conventional seismic method needs improvement or replacement to solve its limitations. In this study, P-wave velocity and amplitude responses to supercritical CO2 injection in brine-saturated core samples from Jilin oilfield were tested using core displacement and an ultrasonic detection integrated system. Results showed that neither the P-wave velocity nor amplitude could simply be used to monitor the CO2 injection process because of the insensitive or nonmonotonous response. Consequently, a new index was established by synthetically considering these two parameters to invert and monitor the CO2 process, which can be thought of as a newer and more effective assessment criterion for the seismic method.