A method for delivering the required neutron fluence in an accelerator-based boron neutron capture therapy system employing a lithium target.

Accelerator-based boron neutron capture therapy (BNCT) systems employing a solid-state lithium target indicated the reduction of neutron flux over the lifetime of a target, and its reduction could represent the neutron flux model. This study proposes a novel compensatory approach for delivering the required neutron fluence and validates its clinical applicability. The proposed approach relies on the neutron flux model and the cumulative sum of real-time measurements of proton charges. The accuracy of delivering the required neutron fluence for BNCT using the proposed approach was examined in five Li targets. With the proposed approach, the required neutron fluence could be delivered within 3.0%, and within 1.0% in most cases. However, those without using the proposed approach exceeded 3.0% in some cases. The proposed approach can consider the neutron flux reduction adequately and decrease the effect of uncertainty in neutron measurements. Therefore, the proposed approach can improve the accuracy of delivering the required fluence for BNCT even if a neutron flux reduction is expected during treatment and over the lifetime of the Li target. Additionally, by adequately revising the approach, it may apply to other type of BNCT systems employing a Li target, furthering research in this direction.

Evaluating optimal quality assurance and quality control conditions of activation measurements at the accelerator-based boron neutron capture therapy system employing a lithium target.

Evaluating neutron output is important to ensure proper dose delivery for patients in boron neutron capture therapy (BNCT). It requires efficient quality assurance (QA) and quality control (QC) while maintaining measurement accuracy. This study investigated the optimal measurement conditions for QA/QC of activation measurements using a high-purity germanium (HP-Ge) detector in an accelerator-based boron neutron capture therapy (AB-BNCT) system employing a lithium target. The QA/QC uncertainty of the activation measurement was evaluated based on counts, reproducibility, and standard radiation source uncertainties. Measurements in a polymethyl methacrylate (PMMA) cylindrical phantom using aluminum-manganese (Al-Mn) foils and aluminum-gold (Al-Au) foils and measurements in a water phantom using gold wire with and without cadmium cover were performed to determine the optimal measurement conditions. The QA/QC uncertainties of the activation measurements were 4.5% for Au and 4.6% for Mn. The optimum irradiation proton charge and measurement time were determined to be 36 C and 900 s for measurements in a PMMA cylindrical phantom, 7.0 C and 900 s for gold wire measurements in a water phantom, and 54 C and 900 s at 0-2.2 cm depth and 3,600 s at deeper depths for gold wire measurements with cadmium cover. Our results serve as a reference for determining measurement conditions when performing QA/QC of activation measurements using HP-Ge detectors at an AB-BNCT employing a lithium target.

Selective preparation of lithium carbonate from overhaul slag by high temperature sulfuric acid roasting - Water leaching.

An efficient recycling process is developed to recover valuable materials from overhaul slag and reduce its harm to the ecological environment. The high temperature sulfuric acid roasting - water leaching technology is innovatively proposed to prepare Li2CO3 from overhaul slag. Under roasting conditions, fluorine volatilizes into the flue gas with HF, lithium is transformed into NaLi(SO4), aluminum is firstly transformed into NaAl(SO4)2, and then decomposed into Al2O3, so as to selective extraction of lithium. Under the optimal roasting - leaching conditions, the leaching rate of lithium and aluminum are 95.6% and 0.9%, respectively. Then the processes of impurity removal, and settling lithium are carried out. The Li2CO3 with recovery rate of 72.6% and purity of 98.6% could be obtained under the best settling lithium conditions. Compared with the traditional process, this work has short flow, high controllability, remarkable technical, economic, and environmental benefits. This comprehensive recycling technology is suitable for overhaul slag, and has great practical application potential for the disposal of other hazardous wastes in electrolytic aluminum industry.

Sustainable reprocessing of lithium iron phosphate batteries: A recovery approach using liquid-phase method at reduced temperature.

Lithium iron phosphate batteries, known for their durability, safety, and cost-efficiency, have become essential in new energy applications. However, their widespread use has highlighted the urgency of battery recycling. Inadequate management could lead to resource waste and environmental harm. Traditional recycling methods, like hydrometallurgy and pyrometallurgy, are complex and energy-intensive, resulting in high costs. To address these challenges, this study introduces a novel low-temperature liquid-phase method for regenerating lithium iron phosphate positive electrode materials. By using N2H4·H2O as a reducing agent, missing Li+ ions are replenished, and anti-site defects are reduced through annealing. This process restores nearly all missing Li+ ions at 80 °C/6h. After high-temperature sintering at 700 °C/2h, the regenerated LiFePO4 matches commercial LiFePO4 in terms of anti-site defects and exhibits excellent performance with a 97 % capacity retention rate after 100 cycles at 1C. Compared to high-temperature techniques, this low-temperature liquid-phase method is simpler, safer, and more energy-efficient, offering a blueprint for reclaiming discarded LiFePO4 and similar materials.

Ferrioxalate photolysis-assisted green recovery of valuable resources from spent lithium iron phosphate batteries.

Recovering valuable resources from spent cathodes while minimizing secondary waste generation is emerging as an important objective for the future recycling of spent lithium-ion batteries, including lithium iron phosphate (LFP) batteries. This study proposes the use of oxalic acid leaching followed by ferrioxalate photolysis to separate and recover cathode active material elements from spent LFP batteries. The cathode active material can be rapidly dissolved at room temperature using appropriate quantities of oxalic acid and hydrogen peroxide, as determined through thermodynamic calculations. The dissolved ferrioxalate complex ion (Fe(C2O4)33-) is selectively precipitated through subsequent photolysis at room temperature. Depending on the initial concentration, the decomposition ratio can exceed 95 % within 1-4 h. Molecular mechanism analysis reveals that the decomposition of the Fe(C2O4)33- complex ion into water-insoluble FeC2O4·2H2O results in the precipitation of iron and the separation of metal elements. Lithium can be recovered as dihydrogen phosphates through filtration and water evaporation. No additional precipitant is needed and no other side products are generated during the process. Oxalic acid leaching followed by photolysis offers an environmentally friendly and efficient method for metal recovery from spent LFP cathodes. The photochemical process is a promising approach for reducing secondary waste generation in battery recycling.

Recovery of lithium and copper from anode electrode materials of spent LIBs by acidic leaching.

In view of the importance of environmental protection and resource recovery, recycling of spent lithium ion batteries (LIBs) is quite necessary. In the present study, lithium and copper are recycled to lithium carbonate and copper oxide from anode electrode material of the spent LIBs. The anode electrode material is firstly treated with hydrochloric acid to leach lithium (96.6%) and then with nitric acid to leach copper (97.6%). Furthermore, lithium and copper are recovered as lithium carbonate and copper oxide from their respective solutions using precipitation and calcinations. These synthesized products are further characterized using XRD, FE-SEM, and EDX analysis. Finally, a simple process is proposed for the recovery of lithium and copper from anode electrode material of spent LIBs.

Construction of greenly biodegradable bacterial cellulose/UiO-66-NH2 composite separators for efficient enhancing performance of lithium-ion battery.

The disposal of waste lithium batteries, especially waste separators, has always been a problem, incineration and burial will cause environmental pollution, therefore, the development of degradable and high-performance separators has become an important challenge. Herein, UiO-66-NH2 particles were successfully anchored onto bacterial cellulose (BC) separators by epichlorohydrin (ECH) as a crosslinker, then a BC/UiO-66-NH2 composite separator was prepared by vacuum filtration. The ammonia groups (-NH2) from UiO-66-NH2 can form hydrogen bonds with PF6- in the electrolyte, promoting lithium-ion transference. Additionally, UiO-66-NH2 can store the electrolyte and tune the porosity of the separator. The lithium ion migration number (0.62) of the battery assembled with BC/UiO-66-NH2 composite separator increased by 50 % compared to the battery assembled with commercial PP separator (0.45). The discharge specific capacity of the battery assembled with BC/UIO-66-NH2 composite separator after 50 charge and discharge cycles is 145.4 mAh/g, which is higher than the average discharge specific capacity of 114.3 mAh/g of the battery assembled with PP separator. When the current density is 2C, the minimum discharge capacity of the battery assembled with BC/UiO-66-NH2 composite separator is 85.3 mAh/g. The electrochemical performance of the BC/UiO-66-NH2 composite separator is significantly better than that of the commercial PP separator. In addition, -NH2 can offer a nitrogen source to facilitate degradation of the BC separators, whereby the BC/UiO-66-NH2 composite separator could be completely degraded in 15 days.

Influences of plasma treatment parameters on the hydrophobicity of cathode and anode materials from spent lithium-ion batteries.

The recycling of spent lithium-ion batteries (LIBs) can not only reduce the potential harm caused by solid waste piles to the local environment but also provide raw materials for manufacturing new batteries. Flotation is an alternative approach to achieve the selective separation of cathode and anode active materials from spent LIBs. However, the presence of organic binder on the surface of hydrophilic lithium transition-metal oxides results in losses of cathode materials in the froth phase. In this study, plasma treatment was utilized to remove organic layers from cathode and anode active materials. Firstly, the correlations between plasma treatment parameters (e.g., input power, air flowrate, and treatment time) were explored and the contact angles of cathode and anode active materials were investigated by the response surface methodology. Secondly, differences in the flotation recoveries of cathode and anode active materials were enhanced with plasma modification prior to flotation, which is consistent with the contact angle measurement. Finally, the plasma-modification mechanisms of hydrophobicity of cathode and anode active materials were discussed according to Fourier Transform infrared spectroscopy (FTIR) and X-ray photoelectron spectroscopy (XPS) analyses. The proposed method could be a promising tool to enhance the flotation separation efficiency of cathode and anode active materials for the recycling of spent LIBs.

Study on green closed-loop regeneration of waste lithium iron phosphate based on oxalic acid system.

The recovery of valuable metals from used lithium batteries is essential from an environmental and resource management standpoint. However, the most widely used acid leaching method causes significant ecological harm. Here, we proposed a method of recovering Li and Fe selectively from used lithium iron phosphate batteries by using low-concentration organic acid and completing the closed-loop regeneration. Low-concentration oxalic acid is used to carry out PO43-, which is significantly less soluble in aqueous solution than Li, two-stage selective leaching Li, where the leaching rate of Li reaches 99 %, and the leaching rate of Fe is only 2.4 %. The leach solution is then decontaminated. The solubility of Li3PO4 in aqueous solution is much smaller than that of Li2C2O4, which was required to recover Li to change the pH and Li can be recovered as Li3PO4; Fe can be retrieved as FeC2O4·2H2O, and re-prepared into lithium iron phosphate.

Lithium and cobalt extraction from LiCoO2 assisted by p(VBPDA-co-FDA) copolymers in supercritical CO2.

Supercritical CO2 (scCO2) extraction assisted by complexing copolymers is a promising process to recover valuable metals from lithium-ion batteries (LIBs). CO2, in addition to being non-toxic, abundant and non-flammable, allows an easy separation of metal-complexes from the extraction medium by depressurization, limiting the wastewater production. In this study, CO2-philic gradient copolymers bearing phosphonic diacid complexing groups (poly(vinylbenzylphosphonic diacid-co-1,1,2,2-tetrahydroperfluorodecylacrylate), p(VBPDA-co-FDA)) were synthesized for the extraction of lithium and cobalt from LiCoO2 cathode material. Notably, the copolymer was able to play the triple role of leaching agent, complexing agent and surfactant. The proof of concept for leaching, complexation and extraction was achieved, using two different extraction systems. A first extraction system used aqueous hydrogen peroxide as reducing agent while it was replaced by ethanol in the second extraction system. The scCO2 extraction conditions such as extraction time, temperature, functional copolymer concentration, and the presence of additives were optimized to improve the metals extraction from LiCoO2 cathode material, leading to an extraction efficiency of Li and Co up to ca. 75 % at 60 °C and 250 bar.

Upgrading anode graphite from retired lithium ion batteries via solid-phase exfoliation by mechanochemical strategy.

Vast quantities of anode graphite from waste lithium ion batteries (LIBs), as a type of underrated urban mine, has enormous potential to be exploited for resource recovery. Herein, we propose a benign process integrating low-temperature pyrolysis and mechanochemical techniques to upcycle spent graphite (SG) from end-of-life LIBs. Pyrolysis at 500 °C leads to about 82.2 % PVDF dissociation in thermal treated graphite (TG). Solid-phase exfoliation via ball milling assisted by urea successfully produces abundant graphite flakes and a small amount of monolayer graphene nanosheet at the edge of mechanochemically processed graphite (MG). Subsequent rinsing removes the residual LiF salts. High purity and unique edge structural features of the as-prepared MG offer more active sites and storage reservoir for intercalation and de-intercalation of lithium ions, resulting in enhanced lithium-ion diffusion kinetics, excellent reversible specific capacity and desirable rate capability. Inspiringly, MG exhibits a remarkably enhanced initial specific charge capacity of 521.3 mAh g-1 during the first charge-discharge, and only declines from 569.9 mAh g-1 to 538 mAh g-1 with slight attenuation after 50 consecutive cycles at 0.1 A/g, indicating satisfactory cycle stability. Additionally, the purification and reconstruction mechanism for MG have been illustrated in detail. This study offers a green strategy to reconstruct and upgrade anode graphite from LIBs, which can realize sustainable waste management.

Crystal phase and nanoscale size regulation utilizing the in-situ catalytic pyrolysis of bamboo sawdust in the recycling of spent lithium batteries.

Current Li-ion battery (LIB) recycling methods exhibit the disadvantages of low metal recovery efficiencies and high levels of pollution and energy consumption. Here, products generated via the in-situ catalytic pyrolysis of bamboo sawdust (BS) were utilized to regulate the crystal phase and nanoscale size of the NCM cathode to enhance the selective Li extraction and leaching efficiencies of other valuable metals from spent LIBs. The catalytic effect of the NCM cathode significantly promoted the release of gases from BS pyrolysis. These gases (H2, CO, and CH4) finally transformed the crystal phase of the NCM cathode from LiNixCoyMnzO2 into (Ni-Co/MnO/Li2CO3)/C. The size of the spent NCM cathode material was reduced approximately 31.7-fold (from 4.1 µm to 129.2 nm) after roasting. This could be ascribed to the in-situ catalytic decomposition of aromatic compounds generated via the primary pyrolysis of BS into C and H2 on the surface of the cathode material, resulting in the formation of the nanoscale composite (Ni-Co/MnO/Li2CO3)/C. This process enabled the targeted control of the crystal phase and nanoscale size of the material. Water leaching studies revealed a remarkable selective Li extraction efficiency of 99.27 %, and sulfuric acid leaching experiments with a concentration of 2 M revealed high extraction efficiencies of 99.15 % (Ni), 93.87 % (Co), and 99.46 % (Mn). Finally, a novel mechanism involving synergistic thermo-reduction and carbon modification for crystal phase regulation and nanoscale control was proposed. This study provides a novel concept for use in enhancing the recycling of valuable metals from spent LIBs utilizing biomass waste and practices the concept of "treating waste with waste".

Mixed crushing and competitive leaching of all electrode material components and metal collector fluid in the spent lithium battery.

Hydrometallurgy is a primary method for recovering cathode electrode materials from spent lithium-ion batteries (LIBs). Most of the current research materials are pure cathode electrode materials obtained through manual disassembly. However, the spent LIBs are typically broken as a whole during the actual industrial recycling which makes the electrode materials combined with the collector fluid. Therefore, the competitive leaching between metal collector fluid and electrode material was examined. The pyrolysis characteristics of the electrode materials were analyzed to determine the pyrolysis temperature. The electrode sheet was pyrolyzed and then crushed for competitive leaching. The effect of pyrolysis was analyzed by XPS. The competitive leaching behavior was studied based on leaching agent concentration, leaching time and leaching temperature. The composition and morphology of the residue were determined to prove the competitive leaching results by XRD-SEM. TG results showed that 500 °C was the suitable pyrolysis temperature. XPS analysis demonstrated that pyrolysis can completely remove PVDF. Li and Co were preferentially leached during the competitive leaching while the leaching rates were 90.10% and 93.40% with 50 min leaching at 70 °C. The Al and Cu had weak competitive leachability and the leaching rate was 29.10% and 0.00%. XRD-SEM analysis showed that Li and Co can be fully leached with residual Al and Cu remaining. The results showed that the mixed leaching of electrode materials is feasible based on its excellent selective leaching properties.

Facile fabrication of regenerated cellulose-based separators for high-performance lithium-ion batteries by regulating degrees of polymerization.

Cellulose-based separators have great application prospects in the field of lithium-ion batteries (LIBs) due to their excellent wettability and thermal stability. However, most current cellulose-based separators come from high-cost nanocellulose and bacterial cellulose. Herein, regenerated cellulose (RC) separators were prepared from dissolving pulp with different degrees of polymerization (DPs) by using the NaOH/urea/thiourea dissolution system as well as a nonsolvent-induced phase separation method. The results showed that the DP of cellulose had a significant influence on the mechanical properties, pore structure, and electrochemical properties of the resultant RC separator. An appropriate increase in the DP could improve the mechanical strength, porosity, and ionic conductivity of the separator. The RC separator with a DP of 599 exhibited the best performance with a porosity of 56.1 %, an average pore size of 305 nm, an electrolyte uptake of 339 %, a tensile strength of 38.3 MPa, and an ionic conductivity of 1.88 mS·cm-1. The lithium-ion battery prepared with the optimal RC separator had a specific capacity of 156.55 mAh/g for 100 cycles at a current density of 0.5 C and a coulombic efficiency of more than 96 %, which was a clear advantage over the commercially available Celgard2400 and cellulose separators. This work makes contributions to the development of high-performance LIBs separators from cellulose.

Direct synthesis of a lithium carboxymethyl cellulose binder using wood dissolving pulp for high-performance LiFePO4 cathodes in lithium-ion batteries.

Lithium carboxymethyl cellulose (CMC-Li) is a promising novel water-based binder for lithium-ion batteries. The direct synthesis of CMC-Li was innovatively developed using abundant wood dissolving pulp materials from hardwood (HW) and softwood (SW). The resulting CMC-Li-HW and CMC-Li-SW binders possessed a suitable degree of substitutions and excellent molecular weight distributions with an appropriate quantity of long- and short-chain celluloses, which facilitated the construction of a reinforced concrete-like bonding system. When used as cathode binders in LiFePO4 batteries, they uniformly coated and dispersed the electrode materials, formed a compact and stable conductive network with high mechanical strength and showed sufficient lithium replenishment. The prepared LiFePO4 batteries exhibited good mechanical stability, low charge transfer impedance, high initial discharge capacity (∼180 mAh/g), high initial Coulombic efficiency (99 %), excellent cycling performance (<3% loss over 200 cycles) and good rate capability, thereby outperforming CMC-Na and the widely used cathode binder polyvinylidene fluoride.

A fresh perspective on dissociation mechanism of cellulose in DMAc/LiCl system based on Li bond theory.

In this case, various characterization technologies have been employed to probe dissociation mechanism of cellulose in N,N-dimethylacetamide/lithium chloride (DMAc/LiCl) system. These results indicate that coordination of DMAc ligands to the Li+-Cl- ion pair results in the formation of a series of Lix(DMAc)yClz (x = 1, 2; y = 1, 2, 3, 4; z = 1, 2) complexes. Analysis of interaction between DMAc ligand and Li center indicate that Li bond plays a major role for the formation of these Lix(DMAc)yClz complexes. And the saturation and directionality of Li bond in these Lix(DMAc)yClz complexes are found to be a tetrahedral structure. The hydrogen bonds between two cellulose chains could be broken at the nonreduced end of cellulose molecule via combined effects of basicity of Cl- ion and steric hindrance of [Li (DMAc)4]+ unit. The unique feature of Li bond in Lix(DMAc)yClz complexes is a key factor in determination of the dissociation mechanism.

Adsorption behavior of hydrogen sulfide in the channels of Li-ABW zeolite: A study using density functional theory.

H2S is a highly toxic, flammable gas that poses risks to health, the environment, and industrial infrastructure. Zeolites, with their high porosity, offer a promising solution for its removal. This study employs density functional theory (DFT) to investigate the adsorption behavior of H2S within the Li-ABW zeolite framework, focusing on the synergistic effect of co-adsorbed water molecules. Six distinct systems were modeled: empty Li-ABW zeolite, half and full filled Li-ABW with H2O or H2S molecules, and equally filled zeolite with H2S and H2O molecules. Detailed analysis of geometric, energetic, and electronic properties reveals that the presence of water significantly enhances H2S adsorption in Li-ABW. Increased bond lengths between H2S and the zeolite framework suggest possible dissociative adsorption, while weakened H2S-zeolite interaction compared to H2O-zeolite interaction indicates facile H2S desorption. Furthermore, charge transfer analysis and HOMO/LUMO plots highlight stronger interactions and a more balanced electron distribution in the co-adsorbed system. Interestingly, the presence of water minimizes structural deformations of the zeolite framework while facilitating the formation of additional hydrogen bonds, potentially further promoting H2S desorption through water extraction. These findings demonstrate that Li-ABW zeolite, particularly in conjunction with water molecules, exhibits remarkable potential for efficient and selective H2S adsorption, offering promising avenues for practical applications in gas sweetening and industrial gas purification. In order to realize this potential, further investigation into the effects of solvents and cation exchange is necessary, which are outlined for future research.

An integrated electrode material based on corn straw cellulose biochar with three-dimensional network porous structure for boosting electrochemical performance of lithium batteries.

In this work an integrated electrode material based on the VS4 nanoparticles grow on three-dimensional network porous biochar is put forward, forming a heterostructure that significantly boost the rate and cycle performance in lithium batteries. Biochar derives from two-steps treatment removing partial cellulose and hemicellulose, possessing three-dimensional network porous structure and naturally nitrogenous. The integrated electrode material constructs the continuous electrons transfer network, accommodates the volume expansion and traps the polar polysulfides efficiently. After 100 cycles at 1C, the integrated electrode with biochar shows the highest specific discharge capacity. Even at 2C, the three-dimensional electrode can display a high specific discharge capacity of 798.6 mAh·g-1. Thus, our study has pointed the innovations approach of constructing integrated electrode materials with porous structure biochar to enhance the electrochemical performance of lithium batteries.

Redox-active NiS@bacterial cellulose nanofiber composite separators with superior rate capability for lithium-ion batteries.

Separator is an essential component of lithium-ion batteries (LIBs), which is placed between the electrodes to impede their electrical contact and provide the transport channels for lithium ions. Traditionally, the separator contributes the overall mass of LIBs, thereby reducing the gravimetric capacity of the devices. Herein, a dual-layer redox-active cellulose separator is designed and fabricated to enhance the electrochemical performances of LIBs by introducing NiS. The presented separator is composed of an insulating bacterial cellulose (BC) nanofiber layer and a conductive, and redox-active NiS@BC/carbon nanotubes layer. By using the NiS@BC separator, the discharge capacity of the LiFePO4//Li half battery is enhanced to 117 mAh g-1 at a current of 2C owing to the redox-activity of NiS. Moreover, the functional separator-electrode interface can facilitate the homogenous Li stripping/plating and depress the polarization upon the repeated stripping/plating process. Consequently, the battery containing the redox-active separator exhibits outstanding cycle stability and rate capability. The present study contributes a novel strategy for the developments of functional separators to improve the electrochemical properties of LIBs.

Ion-imprinted membranes for lithium recovery: A review.

This review critically examines the effectiveness of ion-imprinted membranes (IIMs) in selectively recovering lithium (Li) from challenging sources such as seawater and brine. These membranes feature customized binding sites that specifically target Li ions, enabling selective separation from other ions, thanks to cavities shaped with crown ether or calixarene for improved selectivity. The review thoroughly investigates the application of IIMs in Li extraction, covering extensive sections on 12-crown-4 ether (a fundamental crown ether for Li), its modifications, calixarenes, and other materials for creating imprinting sites. It evaluates these systems against several criteria, including the source solution's complexity, Li+ concentration, operational pH, selectivity, and membrane's ability for regeneration and repeated use. This evaluation places IIMs as a leading-edge technology for Li extraction, surpassing traditional methods like ion-sieves, particularly in high Mg2+/Li+ ratio brines. It also highlights the developmental challenges of IIMs, focusing on optimizing adsorption, maintaining selectivity across varied ionic solutions, and enhancing permselectivity. The review reveals that while the bulk of research is still exploratory, only a limited portion has progressed to detailed lab verification, indicating that the application of IIMs in Li+ recovery is still at an embryonic stage, with no instances of pilot-scale trials reported. This thorough review elucidates the potential of IIMs in Li recovery, cataloging advancements, pinpointing challenges, and suggesting directions for forthcoming research endeavors. This informative synthesis serves as a valuable resource for both the scientific community and industry professionals navigating this evolving field.