SEARCH FOR EXPERIMENTAL EVIDENCE OF DOSE-RATE AND WALL SCATTERING EFFECTS IN THE THERMOLUMINESCENCE RESPONSE OF LIF:MG,TI (TLD-100).

An experimental investigation into the possibility of dose-rate effects and wall scatter in the thermoluminescent response of LiF:Mg,Ti (TLD-100) was carried out. The investigation was motivated by theoretical simulations predicting the possible presence of dose-rate effects coupled with the lack of detailed experimental studies. The dose rate was varied by changing the source to sample distance, by the use of attenuators, sources of 137Cs of various activities, filtration and the construction of identical geometrical irradiators of Teflon and stainless steel. Four levels of dose in the linear dose response region were studied at 10-2 Gy, 1.5 × 10-2 Gy, 0.1 Gy and 0.5 Gy to avoid complications in interpretation due to supralinearity above 1 Gy. At the dose of 1.5 × 10-2 Gy, the dose rate was varied by five orders of magnitude from 4.9 × 10-3 Gy s-1 to 4.9 × 10-8 Gy s-1. At the other levels of dose, a one to two orders of magnitude in dose rate was achieved. Within the measurement uncertainty of 5-10%, no dose-rate effects were observed in any of the experimental measurements and no changes in the shape of the glow curve were observed. The maximum wall scatter effect (Teflon to stainless steel) was measured at ~8% within the experimental uncertainty and well below expectations. The results are encouraging with respect to the accurate and reproducible use of LiF:Mg,Ti under various experimental conditions of irradiation.

MANIPULATION OF THE DOSE-RESPONSE OF COMPOSITE GLOW PEAK 5 IN THE THERMOLUMINESCENCE OF LiF:Mg,Ti (TLD-100) VIA OPTICAL EXCITATION POST-IRRADIATION: POTENTIAL FOR IMPROVED DOSE-RESPONSE LINEARITY BEYOND 1 Gy.

Many dosimetric applications and especially those involved in clinical dosimetry are hampered by the supralinearity of TLD-100 which begins at a level of dose of 1 Gy. This research investigates the effect of optical excitation following irradiation on the dose-response. It is expected that this will lead to a more linear dose-response, however, irrespective of the hoped-for linearity, the theoretical/kinetic simulations of the effect of optical excitation will further enhance our understanding of the thermoluminescence mechanisms, especially the role of spatially correlated trapping and luminescent centers. In the following, the various stages carried out in these investigations are discussed and preliminary results presented.

REVIEW OF DOSE-RATE EFFECTS IN THE THERMOLUMINESCENCE OF Lif:mg,ti (HARSHAW).

The literature describing the experimental investigations of possible dose-rate effects in the thermoluminescence (TL) of LiF:Mg,Ti (Harshaw) is reviewed. The total lack of glow curve analysis, coupled with inclusion of all or part of the high temperature TL and absence of parallel measurements of possible dose-rate effects in the irradiation stage severely limit the scientific and technical level of the experiments. In addition, the experimental procedures are far from sufficient to warrant any conclusion concerning the presence or absence of dose-rate effects in the TL of LiF:Mg,Ti. This decision is contrary to the widely held belief that there are no dose-rate effects in the TL of LiF:Mg,Ti. In addition, the literature on dose-rate effects in the optical absorption (irradiation stage) of LiF is reviewed and is found contradictory. No dose-rate studies have been carried out on optical absorption in LiF:Mg,Ti. Kinetic simulations demonstrating the possibility, even likelihood, of dose-rate effects are also reviewed. Dose-rate effects are shown to be likely due to competition between excitation and recombination in the irradiation stage. Some other possible mechanisms involving multiple charge carrier trapping are suggested. Further definitive experiments are sorely needed, but the interested researcher should beware, it is not an easy task.

Doses to LiF :Ti, Mg chips encapsulated in plastic extremity rings as a result of radon gas exposure.

Previous studies measured the effects of (222)Rn on various thermoluminescent dosemeters (TLDs). This study quantified the effects of (222)Rn on LiF : Ti,Mg chips encapsulated in plastic extremity rings. For 28 d, one batch of TLDs was left in a chamber with high radon levels, and another batch in a control chamber with normal background radon levels. A few TLDs in each batch were removed from the rings for direct exposure to the ambient air in each chamber. Passive continuous radon monitors (CRMs) recorded the (222)Rn levels. TLDs were processed using a third-party dosimetry company, CRM data were analysed, and the relationship between integrated (222)Rn concentration and TLD response was determined. The batch of TLDs in the experimental chamber showed a weak response to (222)Rn gas, which was in the order of 0.5 nSv Bq(-1) m(3) d(-1).

A method to minimise the fading effects of LiF:Mg,Ti (TLD-600 and TLD-700) using a pre-heat technique.

Passive integrating dosemeters [thermoluminescent dosimeter (TLD) and optically stimulated luminescence (OSL)] are the only legally permitted individual dosemeters for occupational external radiation exposure monitoring in Korea. Also its maximum issuing cycle does not exceed 3 months, and the Korean regulations require personal dosemeters for official assessment of external radiation exposure to be issued by an approved or rather an accredited dosimetry service according to ISO/IEC 17025. KHNP (Korea Hydro & Nuclear Power, LTD), a unique operating company of nuclear power plants (NPPs) in Korea, currently has a plan to extend a TLD issuing cycle from 1 to 3 months under the authors' fading error criteria, ±10%. The authors have performed a feasibility study that minimises post-irradiation fading effects within their maximum reading cycle employing pre-heating technique. They repeatedly performed irradiation/reading a bare TLD chip to determine optimum pre-heating conditions by analysing each glow curve. The optimum reading conditions within the maximum reading cycle of 3 months were decided: a pre-heating temperature of 165°C, a pre-heating time of 9 s, a heating rate of 25°C s(-1), a reading temperature of 300°C and an acquisition time of 10 s. The fading result of TLD-600 and TLD-700 carried by newly developed time temperature profile (TTP) showed a much smaller fading effect than that of current TTP. The result showed that the fading error due to a developed TTP resulted in a ∼5% signal loss, whereas a current TTP caused a ∼15% loss. The authors also carried out a legal performance test on newly developed TTP to confirm its possibility as an official dosemeter. The legal performance tests that applied the developed TTP satisfied the criteria for all the test categories.

Correction factors kE and kQ for LiF-TLDs for dosimetry in megavoltage electron and photon beams.

For the determination of absorbed dose to water D,using thermolumeniscence (TL) probes in a beam different from that used for calibration, correction factors for radiation type and radiation quality kE and kQ are needed. Values for kE and kQ for two different shapes of LiF probes (rods and disks) were obtained for high-energy photon and electron beams. The relation between the absorbed dose to the medium (water) D, measured by ion-chambers according to DIN 6800-2, 2008 and TL-probes having a (60)Co-calibration factor, leads for each shape and each batch of LiF probes to correction factors for radiation type and radiation quality kE and kQ.. The influence of the shape on the correction factor of the probes amounts in our experiment up to 2%. Therefore, it is recommended that the correction factors kE and kQ for rods and disks should be checked for each batch of LiF-detectors.

The modified unified interaction model: incorporation of dose-dependent localised recombination.

The unified interaction model (UNIM) was developed to simulate thermoluminescence (TL) linear/supralinear dose-response and the dependence of the supralinearity on ionisation density, i.e. particle type and energy. Before the development of the UNIM, this behaviour had eluded all types of TL modelling including conduction band/valence band (CB/VB) kinetic models. The dependence of the supralinearity on photon energy was explained in the UNIM as due to the increasing role of geminate (localised recombination) with decreasing photon/electron energy. Recently, the Ben Gurion University group has incorporated the concept of trapping centre/luminescent centre (TC/LC) spatially correlated complexes and localised/delocalised recombination into the CB/VB kinetic modelling of the LiF:Mg,Ti system. Track structure considerations are used to describe the relative population of the TC/LC complexes by an electron-hole or by an electron-only as a function of both photon/electron energy and dose. The latter dependence was not included in the original UNIM formulation, a significant over-simplification that is herein corrected. The modified version, the M-UNIM, is then applied to the simulation of the linear/supralinear dose-response characteristics of composite peak 5 in the TL glow curve of LiF:Mg,Ti at two representative average photon/electron energies of 500 and 8 keV.

Studies on energy response of newly developed LiF:Mg,Cu,P TL chips with additional PbO doping.

One of the most important characteristics of thermoluminescent detectors, if they are intended to be used in a wide range of energies, is their energy response. A comparison of the energy characteristics of the newly developed LiF:Mg,Cu,P chips with additional PbO doping (GR-200E) against GR-200A LiF:Mg,Cu,P was attempted to improve further the accuracy of personal dosimetry. Hp(10) energy response of GR-200E is quite different from that of GR-200A. For GR-200E, the anomalous energy response can be eliminated and the over-response to low-energy photons should be filtered properly. The GR-200E under the copper filter provided results within 4 % with respect to the conventional quantity value over the energy range from 65 to 1250 keV. The ratio of the Hp(10) response of the Cu-covered filters for GR-200A to that of those covered with plastic for GR-200E is a very good tool for identifying the radiation quality in the range studied. The accuracy in the dose evaluated from TLD measurements can be greatly increased.

Further studies on the role of dopants in LiF:Mg,Cu,Si thermoluminescent material.

The 3-D thermoluminescence spectra and glow curves of LiF:Mg,Cu,Si, LiF:Mg,Cu, LiF:Mg,Si and LiF:Cu,Si with low concentrations of Mg and Cu were measured and were compared with those with high concentrations to investigate further the role of dopants in LiF:Mg,Cu,Si material. The shape of glow curves of the four samples is similar; however, LiF:Cu,Si sample had no Mg dopant. It is concluded that the TL emission to be from self-trapped excitons in LiF, and this emission could be enhanced and altered by Mg, Cu and Si dopants in LiF:Mg,Cu,Si; all three dopants are necessary to obtain the bright TL emission and may be involved in the luminescence process; Mg seems to be the most essential dopant and Cu is involved in the trapping although the role of Mg dominates; both Cu and Si play a role in the main emission process and Cu also plays a role in reducing the emission around 610 nm.

LiF, an underestimated supercontinuum source in femtosecond transient absorption spectroscopy.

We present supercontinua generated in LiF and CaF(2) revealing that LiF is advantageous especially in the near UV region since it pushes the cut-off wavelength about 17 nm towards lower wavelengths and the occurrence of color centers, which has been considered as a drawback up to now, is not a limitation for its applicability in femtosecond transient absorption spectroscopy. Even though the color centers occur within a short time of illumination, they do not influence the supercontinuum generation significantly and they can furthermore, if desired, be eliminated from the substrate simply by heating. Thus LiF is a promising substrate for broad band measurements in the UV/vis range.

Multiple excitation of Fuchs-Kliewer phonons by Ne⁺ ions back-scattered by the LiF(100) surface at grazing incidence.

An analytic model is developed to describe the inelastic processes occurring when keV Ne(+) ions are scattered at grazing incidence by the (100) surface of LiF. The large energy losses (up to 30 eV) of the reflected Ne(+) particles reported by Borisov et al (1999 Phys. Rev. Lett. 83 5378) are shown to arise specifically from the long-range coupling between the projectiles and the so-called Fuchs-Kliewer (FK) optical phonons of LiF whose fields extend far outside the surface. The strength of the coupling is estimated, allowing one to compute the average number of excited FK phonon quanta (hωS = 0.071 eV) and hence the mean energy losses. For emerging, neutralized Ne(0), a distinct energy loss mechanism is shown to occur, namely the excitation of FK phonons and other types of surface collective modes associated with the screening of the F(0) 'hole' left behind by the neutralization process. This mechanism contributes a large fraction of the loss, additional to that suffered by the incident Ne(+) ion. The model explains the experimental observations quantitatively (1999 Phys. Rev. Lett. 83 5378). The paper ends with a discussion of the large energy broadening of the observed loss peaks.

[Development of external quality control protocol for CyberKnife beams dosimetry: preliminary tests multicentre]. / Développement d'une procédure de contrôle de qualité externe des faisceaux du CyberKnife: étude préliminaire multicentrique.

PURPOSE: To develop an external quality control procedure for CyberKnife(®) beams. This work conducted in Nancy, has included a test protocol initially drawn by the medical physicist of Nancy and Lille in collaboration with Equal-Estro Laboratory. MATERIALS AND METHODS: A head and neck anthropomorphic phantom and a water-equivalent homogeneous cubic plastic test-object, so-called "MiniCube", have been used. Powder and solid thermoluminescent dosimeters as well as radiochromic films have been used to perform absolute and relative dose studies, respectively. The comparison between doses calculated by Multiplan treatment planning system and measured doses have been studied in absolute dose. The dose distributions measured with films and treatment planning system calculations have been compared via the gamma function, configured with different tolerance criteria. RESULTS: This work allowed, via solid thermoluminescent dosimeter measurements, verifying the beam reliability with a reproducibility of 1.7 %. The absolute dose measured in the phantom irradiated by the seven participating centres has shown an error inferior to the standard tolerance limits (± 5 %), for most of participating centres. The relative dose measurements performed at Nancy and by the Equal-Estro laboratory allowed defining the most adequate parameters for gamma index (5 %/2mm--with at least 95 % of pixels satisfying acceptability criteria: γ<1). These parameters should be independent of the film analysis software. CONCLUSION: This work allowed defining a dosimetric external quality control for CyberKnife(®) systems, based on a reproducible irradiation plan through measurements performed with thermoluminescent dosimeters and radiochromic films. This protocol should be validated by a new series of measurement and taking into account the lessons of this work.

Thermoluminescence responses of photon- and electron-irradiated lithium potassium borate co-doped with Cu+Mg or Ti+Mg.

New glasses Li2CO3-K2CO3-H3BO3 (LKB) co-doped with CuO and MgO, or with TiO2 and MgO, were synthesized by the chemical quenching technique. The thermoluminescence (TL) responses of LKB:Cu,Mg and LKB:Ti,Mg irradiated with 6 MV photons or 6 MeV electrons were compared in the dose range 0.5-4.0 Gy. The standard commercial dosimeter LiF:Mg,Ti (TLD-100) was used to calibrate the TL reader and as a reference in comparison of the TL properties of the new materials. The dependence of the responses of the new materials on (60)Co dose is linear in the range of 1-1000 Gy. The TL yields of both of the co-doped glasses and TLD-100 are greater for electron irradiation than for photon irradiation. The TL sensitivity of LKB:Ti,Mg is 1.3 times higher than the sensitivity of LKB:Cu,Mg and 12 times less than the sensitivity of TLD-100. The new TL dosimetric materials have low effective atomic numbers, good linearity of the dose responses, excellent signal reproducibility, and a simple glow curve structure. This combination of properties makes them suitable for radiation dosimetry.

Improvement and formation of UV-induced damage on LBO crystal surface during long-term high-power third-harmonic generation.

We demonstrate the improvement and formation of UV-induced damage on LBO crystal output surface during long-term (130 h) high-power (20 W) high-repetition-rate (80 kHz) third-harmonic generation. The output surface was super-polished (RMS surface roughness <0.6 nm) to sub-nanometer scale super smooth roughness. The surface lifetime has been improved more than 20-fold compared with the as-polished ones (RMS surface roughness 4.0~8.0 nm). The damage could be attributed to the consequence of thermal effects resulted from impurity absorptions. Simultaneously, it was verified that the impurities originated in part from the UV-induced deposition.

Photostimulated near-infrared persistent luminescence as a new optical read-out from Cr³âº-doped LiGa5O8.

In conventional photostimulable storage phosphors, the optical information written by x-ray or ultraviolet irradiation is usually read out as a visible photostimulated luminescence (PSL) signal under the stimulation of a low-energy light with appropriate wavelength. Unlike the transient PSL, here we report a new optical read-out form, photostimulated persistent luminescence (PSPL) in the near-infrared (NIR), from a Cr(3+)-doped LiGa5O8 NIR persistent phosphor exhibiting a super-long NIR persistent luminescence of more than 1,000 h. An intense PSPL signal peaking at 716 nm can be repeatedly obtained in a period of more than 1,000 h when an ultraviolet-light (250-360 nm) pre-irradiated LiGa5O8:Cr(3+) phosphor is repeatedly stimulated with a visible light or a NIR light. The LiGa5O8:Cr(3+) phosphor has promising applications in optical information storage, night-vision surveillance, and in vivo bio-imaging.

Deactivation effects of the lowest excited state of Ho3+ at 2.9 µm emission introduced by Pr3+ ions in LiLuF4 crystal.

The use of Pr3+ codoping for enhancement of the Ho3+:5I6 →5I7 mid-IR emissions were investigated in the LiLuF4 crystal for the first time. It was found that Pr3+ greatly increased Ho3+ 2.9 µm emission by depopulating the Ho3+:5I7 level while having little influence on the Ho3+:5I6 level, leading to greater population inversion. The energy transfer efficiency from Ho3+:5I7 to Pr3+:3F2 is calculated to be 88%. Based on Judd-Ofelt theory, the 2.9 µm emission cross section is calculated to be 1.91×10(-20) cm2, and the gain property of the Ho3+:5I6 →5I7 transition is discussed. We propose that the Ho, Pr:LiLuF4 crystal may be a promising material for 2.9 µm laser applications.

Dosimetry of a cone-beam computed tomography machine compared with a digital x-ray machine in orthodontic imaging.

INTRODUCTION: Cone-beam computed tomography (CBCT) has become a routine imaging modality for many orthodontic clinics. However, questions remain about the amount of radiation patients are exposed to during the scans. This study determined the amounts of radiation potentially absorbed by a patient during orthodontic imaging with a CBCT machine with various scan settings compared with a conventional 2-dimensional digital x-ray machine. METHODS: The radiation exposures delivered by a next generation i-CAT CBCT machine (Imaging Sciences International, Hatfield, Pa) at various scan settings and orthopantomograph OP100/OC100 digital x-ray machine (Instrumentarium Dental, Tuusula, Finland) during panoramic and cephalometric radiography were recorded using thermoluminescent dosimeters placed inside a head and neck phantom. The manufacturer-recommended settings for an average adult male were used for both types of machines. Effective doses were calculated using the tissue-weighting factors recommended by the 2007 International Commission on Radiological Protection. RESULTS: The effective doses at various voxel sizes and field of view settings ranged from 64.7 to 69.2 µSv for standard resolution CBCT scans (scan time 8.9 s) and 127.3 to 131.3 µSv for high resolution full field of view scans (scan time 17.8 s), and measured 134.2 µSv for a high-resolution landscape scan with a voxel size as would be used for SureSmile (OraMetrix, Richardson, Tex) therapy (scan time 26.9 s). The effective doses for digital panoramic and lateral cephalometric radiographs measured 21.5 and 4.5 µSv, respectively. CONCLUSIONS: CBCT, although providing additional diagnostic and therapeutic benefits, also exposes patients to higher levels of radiation than conventional digital radiography.

Studies of 6Li-NMR properties in different salt solutions in low magnetic fields.

In this article we report the longitudinal relaxation times (T(1)) of various (6)Li salts ((6)LiI, (6)LiCl and (6)LiNO(3)) in D(2)O and H(2)O, measured in low magnetic fields (B(0)=3.5mT). This investigation serves the purpose of clarifying the relaxation behavior of different (6)Li solutions and different concentrations. The measurement were undertaken to establish a framework for future applications of hyperpolarized (6)Li in medical imaging, biological studies and investigations of lithium ion batteries. Time will pass during the transport of hyperpolarized lithium ions to the sample, which leads to a polarization loss. In order to store polarization as long as possible, it is necessary to examine which (6)Li salt solution has the longest relaxation time T(1). Longitudinal relaxation times of (6)Li salts in D(2)O and H(2)O were investigated as a function of concentration and the most extended T(1) was found for (6)LiI in D(2)O and H(2)O. In agreement with the theory the relaxation time T(1) of all (6)Li salts increase with decreasing concentration. In the case of (6)LiI in H(2)O an inverse behavior was observed. We assume that the prolonged T(1) times occur due to formation of (6)LiOH upon the solution of (6)LiI in H(2)O, which settles as a precipitate. By diluting the solution, the precipitate continuously dissolves and approaches T(1) of (6)LiOH (T(1)∼28s), leading to a shorter T(1) relaxation time.

The use of enriched 6Li and 7Li Lif:Mg,Cu,P glass-rod thermoluminescent dosemeters for linear accelerator out-of-field radiation dose measurements.

(6)LiF:Mg,Cu,P and (7)LiF:Mg,Cu,P glass-rod thermoluminescent dosemeters (TLDs) were used for measurements of out-of-field photon and neutron doses produced by Varian iX linear accelerator. Both TLDs were calibrated using 18-MV X-ray beam to investigate their dose-response sensitivity and linearity. CR-39 etch-track detectors (Luxel+, Landauer) were employed to provide neutron dose data to calibrate (6)LiF:Mg,Cu,P TLDs at various distances from the isocentre. With cadmium filters employed, slow neutrons (<0.5 eV) were distinguished from fast neutrons. The average in-air photon dose equivalents per monitor unit (MU) ranged from 1.5±0.4 to 215.5±94.6 µSv at 100 and 15 cm from the isocentre, respectively. Based on the cross-calibration factors obtained with CR-39 etch-track detectors, the average in-air fast neutron dose equivalents per MU range from 10.6±3.8 to 59.1±49.9 µSv at 100 and 15 cm from the isocentre, respectively. Contribution of thermal neutrons to total neutron dose equivalent was small: 3.1±7.2 µSv per MU at 15 cm from the isocentre.

Multiple pulse nanosecond laser induced damage study in LiB3O5 crystals.

Multiple pulse nanosecond laser induced damage in the bulk of LiB3O5 (LBO) crystals was investigated at 1064 nm, 532 nm and 355 nm. Scanning electron microscopy of cleaved damage sites confirmed the presence of different zones that have already been reported in the case of KH2PO4 (KDP). Multi pulse measurements reveal a strong decrease of the damage threshold with increasing pulse number at 1064 nm (fatigue effect). A weaker fatigue effect was observed at 532 nm and no fatigue effect was found at 355 nm. This observation is best explained by an inherently statistical light matter interaction generating laser induced damage. Finally, a polarization dependent damage threshold anisotropy was evidenced at all three wavelengths, being strongest at 1064 nm. The results indicate the importance of Li+ vacancy stabilized color centers for the damage mechanism.