Analysis and removal of bisphenols in recycled plastics using polyethylene glycol.

This study examines the presence of bisphenol A (BPA), S (BPS), F (BPF), and M (BPM) in various recycled plastics readily available on the market (LDPE, HDPE, PET, and PP), in light of European Food Safety Authority (EFSA) limits. Twenty samples of different origin are analyzed, cleaning treatments are applied, and the migration potential of these bisphenols into food is studied. BPM is absent in all samples, but a post-consumer recycled LDPE sample reveals high bisphenol concentrations, raising concerns, reaching 8540 ng/g, 370 ng/g, and 29 ng/g of BPA, BPS, and BPF, respectively. Migration tests show substantial migration of these contaminants into food simulants. Using a cleaning treatment with polyethylene glycol (PEG 400) reduces BPA in LDPE, HDPE, PP, and PET samples by 95%, 99%, 97% and 28%, respectively, highlighting the importance of cleaning treatments across various polymers in plastic recycling. These findings not only protect food safety but addressing environmental challenges associated with plastic recycling.

Bottlenecks in biobased approaches to plastic degradation.

Plastic waste is an environmental challenge, but also presents a biotechnological opportunity as a unique carbon substrate. With modern biotechnological tools, it is possible to enable both recycling and upcycling. To realize a plastics bioeconomy, significant intrinsic barriers must be overcome using a combination of enzyme, strain, and process engineering. This article highlights advances, challenges, and opportunities for a variety of common plastics.

Plastic and terrestrial organic matter degradation by the humic lake microbiome continues throughout the seasons.

Boreal freshwaters go through four seasons, however, studies about the decomposition of terrestrial and plastic compounds often focus only on summer. We compared microbial decomposition of 13C-polyethylene, 13C-polystyrene, and 13C-plant litter (Typha latifolia) by determining the biochemical fate of the substrate carbon and identified the microbial decomposer taxa in humic lake waters in four seasons. For the first time, the annual decomposition rate including separated seasonal variation was calculated for microplastics and plant litter in the freshwater system. Polyethylene decomposition was not detected, whereas polystyrene and plant litter were degraded in all seasons. In winter, decomposition rates of polystyrene and plant litter were fivefold and fourfold slower than in summer, respectively. Carbon from each substrate was mainly respired in all seasons. Plant litter was utilized efficiently by various microbial groups, whereas polystyrene decomposition was limited to Alpha- and Gammaproteobacteria. The decomposition was not restricted only to the growth season, highlighting that the decomposition of both labile organic matter and extremely recalcitrant microplastics continues throughout the seasons.

Comprehensive study of retention influencing gas chromatographic parameters affecting linear retention indices.

Retention in gas chromatographic systems has a central role in the identification of compounds even if detectors providing spectral information are used. But linear retention indices (LRI) of a single compound originating from multiple sources tend to vary greatly, probably due to differences in the experimental settings of the determinations. The effect of gas chromatographic parameters on LRI has been investigated using 41 compounds - previously identified from food contact plastics - and n-alkanes (n-C7-n-C40) used as reference series. As the reproducibility of LRIs under the same conditions is generally very good, the smallest changes in the settings often caused statistically significant, though irrelevant changes in the LRI values. Therefore, a multicriterial scoring-ranking system has been worked out to highlight the LRI value differences. Our results highlight that column length, heating rate, and film thickness can all be the reasons of the varying published LRI values. We also demonstrated that for the reproduction of LRI data, the chemistry (and not simply the polarity) of the stationary phase is crucial.

Enhancing chondrogenic differentiation of mesenchymal stem cells through synergistic effects of cellulose nanocrystals and plastic compression in collagen-based hydrogel for cartilage formation.

Collagen-based (COL) hydrogels could be a promising treatment option for injuries to the articular cartilage (AC) becuase of their similarity to AC native extra extracellular matrix. However, the high hydration of COL hydrogels poses challenges for AC's mechanical properties. To address this, we developed a hydrogel platform that incorporating cellulose nanocrystals (CNCs) within COL and followed by plastic compression (PC) procedure to expel the excessive fluid out. This approach significantly improved the mechanical properties of the hydrogels and enhanced the chondrogenic differentiation of mesenchymal stem cells (MSCs). Radially confined PC resulted in higher collagen fibrillar densities together with reducing fibril-fibril distances. Compressed hydrogels containing CNCs exhibited the highest compressive modulus and toughness. MSCs encapsulated in these hydrogels were initially affected by PC, but their viability improved after 7 days. Furthermore, the morphology of the cells and their secretion of glycosaminoglycans (GAGs) were positively influenced by the compressed COL-CNC hydrogel. Our findings shed light on the combined effects of PC and CNCs in improving the physical and mechanical properties of COL and their role in promoting chondrogenesis.

Nanoscale Simulation of Plastic Contaminants Migration in Packaging Materials and Potential Leaching into Model Food Fluids.

Polymers are the most commonly used packaging materials for nutrition and consumer products. The ever-growing concern over pollution and potential environmental contamination generated from single-use packaging materials has raised safety questions. Polymers used in these materials often contain impurities, including unreacted monomers and small oligomers. The characterization of transport properties, including diffusion and leaching of these molecules, is largely hampered by the long timescales involved in shelf life experiments. In this work, we employ atomistic molecular simulation techniques to explore the main mechanisms involved in the bulk and interfacial transport of monomer molecules from three polymers commonly employed as packaging materials: polyamide-6, polycarbonate, and poly(methyl methacrylate). Our simulations showed that both hopping and continuous diffusion play important roles in inbound monomer diffusion and that solvent-polymer compatibility significantly affects monomer leaching. These results provide rationalization for monomer leaching in model food formulations as well as bulky industry-relevant molecules. Through this molecular-scale characterization, we offer insights to aid in the design of polymer/consumer product interfaces with reduced risk of contamination and longer shelf life.

Multi-target aptamer assay for endocrine-disrupting phthalic acid ester panel screening in plastic leachates.

A multi-target aptamer assay was developed as a phthalic acid ester (PAE) panel to screen selected PAEs in plastic leachate samples. The panel comprises 13 PAEs (PAE-13), namely dimethyl phthalate, diethyl phthalate, di-n-butyl phthalate, di-n-hexyl phthalate, diisobutyl phthalate, diisononyl phthalate, diisodecyl phthalate, mono-2-ethylhexyl phthalate, di-2-ethylhexyl phthalate, diphenyl phthalate, butyl benzyl phthalate, dicyclohexyl phthalate, and phthalic acid. Herein, we proposed an aptamer assay using a newly truncated aptamer (20-mer) and the 7-aminoactinomycin D fluorophore, which selectively binds to guanine in single-stranded DNA, resulting in increased fluorescence intensity. The assay is highly selective for PAE-13 clusters. The selectivity of the assay was evaluated using 13 different PAEs and mixtures depending on the side chain structure. The quantitative detection of PAEs was demonstrated by adopting mixed PAE-13 simulants and achieved a limit of detection of ∼1.4 pg/mL. The repeatability and reproducibility of the assay were also evaluated by presenting acceptable coefficients of variation (%CV less than 10% and 15%, respectively). The performance of the assay was demonstrated by analyzing the plastic leachate samples, and the positive correlation (correlation coefficient, r = 0.985) was confirmed by comparing them with the total sum of individual PAE peak areas obtained by gas chromatography mass spectrometry analysis.

Marine degradation and ecotoxicity of conventional, recycled and compostable plastic bags.

Plastic bags are currently a major component of marine litter, causing aesthetical nuisance, and undesirable effects on marine fauna that ingest them or are entangled. Plastic litter also rises concern on the ecotoxicological effects due to the potential toxicity of the chemical additives leached in aquatic environments. Conventional plastic bags are made of polyethylene, either from first use or recycled, but regulations restricting single-use plastics and limiting lightweight carrier bags (<50 µm thickness) have fostered the replacement of thin PE bags by compostable materials advertised as safer for the environment. In this study, we assess the degradation of commercially available plastic bags in marine conditions at two scales: aquariums (60 days) and outdoors flow-through mesocosm (120 days). Strength at break point and other tensile strength parameters were used as ecologically relevant endpoints to track mechanical degradation. Ecotoxicity has been assessed along the incubation period using the sensitive Paracentrotus lividus embryo test. Whereas PE bags did not substantially lose their mechanical properties within the 60 d aquarium exposures, compostable bags showed remarkable weight loss and tensile strength decay, some of them fragmenting in the aquarium after 3-4 weeks. Sediment pore water inoculum promoted a more rapid degradation of compostable bags, while nutrient addition pattern did not affect the degradation rate. Longer-term mesocosms exposures supported these findings, as well as pointed out the influence of the microbial processes on the degradation efficiency of compostable/bioplastic bags. Compostable materials, in contrast toPE, showed moderate toxicity on sea-urchin larvae, partially associated to degradation of these materials, but the environmental implications of these findings remain to be assessed. These methods proved to be useful to classify plastic materials, according to their degradability in marine conditions, in a remarkably shorter time than current standard tests and promote new materials safer for the marine fauna.

Adsorption and antibacterial studies of a novel hydrogel adsorbent based on ternary eco-polymers doped with sulfonated graphene oxide developed from upcycled plastic waste.

A novel ternary blended polymer composed of cost-effective and readily available polymers was synthesized using poly (vinyl alcohol) (PVA), iota carrageenan (IC), and poly (vinyl pyrrolidone) (PVP). Sulfonated graphene oxide (SGO), prepared from recycled drinking water bottles, was utilized as a doping agent. Varying amounts (1-3 wt%) were combined into the polymer matrix. The produced hydrogel film was examined as a potential adsorbent hydrogel film for the removal of methylene blue (MB) and Gentamicin sulfate (GMS) antibiotic from an aqueous solution. The experimental results demonstrate that the presence of SGO significantly increased the adsorption efficiency of PVA/IC/PVP hydrogel film. The antimicrobial tests revealed that the PVA/IC/PVP-3% SGO hydrogel film exhibited the most potent activity against all the tested pathogenic bacteria. However, the adsorption results for MB and GMS showed that the addition of 3 wt% SGO resulted in a removal percentage that was a two fold increase in the removal percentage compared with the undoped PVA/IC/PVP hydrogel film. Furthermore, the response surface methodology (RSM) model was utilized to examine and optimize several operating parameters, including time, pH of the solution, and initial pollutant concentration. The adsorption kinetics were better characterized by the pseudo-second-order kinetics model. The composite film containing 3 wt% SGO had a maximum adsorption capacity of 606 mg g-1 for MB and 654 mg g-1 for GMS, respectively. The generated nanocomposite hydrogel film demonstrated promising potential for application in water purification systems.

A waste-to-wealth conversion of plastic bottles into effective carbon-based adsorbents for removal of tetracycline antibiotic from water.

Currently, plastic waste and antibiotic wastewater are two of the most critical environmental problems, calling for urgent measures to take. A waste-to-wealth strategy for the conversion of polyethylene terephthalate (PET) plastic bottles into value-added materials such as carbon composite is highly recommended to clean wastewater contaminated by antibiotics. Inspired by this idea, we develop a novel PET-AC-ZFO composite by incorporating PET plastic-derived KOH-activated carbon (AC) with ZnFe2O4 (ZFO) particles for adsorptive removal of tetracycline (TTC). PET-derived carbon (PET-C), KOH-activated PET-derived carbon (PET-AC), and PET-AC-ZFO were characterized using physicochemical analyses. Central composite design (CCD) was used to obtain a quadratic model by TTC concentration (K), adsorbent dosage (L), and pH (M). PET-AC-ZFO possessed micropores (d ≈ 2 nm) and exceptionally high surface area of 1110 m2 g-1. Nearly 90% TTC could be removed by PET-AC-ZFO composite. Bangham kinetic and Langmuir isotherm were two most fitted models. Theoretical maximum TTC adsorption capacity was 45.1 mg g-1. This study suggested the role of hydrogen bonds, pore-filling interactions, and π-π interactions as the main interactions of the adsorption process. Thus, a strategy for conversion of PET bottles into PET-AC-ZFO can contribute to both plastic recycling and antibiotic wastewater mitigation.

Characteristics and adsorption behavior of typical microplastics in long-term accelerated weathering simulation.

Microplastics can function as carriers in the environment, absorbing various toxins and spreading to diverse ecosystems. Toxins accumulated in microplastics have the potential to be re-released, posing a threat. In this study, two typical plastics, namely polyethylene (PE) and polystyrene (PS), along with the degradable plastic poly(butylene adipate-co-terephthalate) (PBAT), were subjected to a long-term ultraviolet alternating weathering experiment. The study investigated the variations in the weathering process and pollutant adsorption of microplastics of different particle sizes. Furthermore, the adsorption capacity of microplastics for various pollutants was assessed. The findings indicate that particle size significantly influences weathering, leading to variations in adsorption capacity. The weathered PE displays a higher adsorption capacity for azo dyes. Additionally, the adsorption capacity of PBAT for neutral red is double that of antibiotics. Importantly, the maximum adsorption capacity of PBAT for pollutants after aging is approximately 10 times greater than that of PE. Consequently, degradable plastics undergoing weathering in the natural environment may pose a higher ecological risk than traditional plastics.

Interactions between methyl octabromo ether flame retardant and expanded polystyrene microplastics in the photoaging process.

Expanded polystyrene (EPS) plastic is widely used because of its low density and lightweight properties, enabling it to float on water and increase its exposure to sunlight. In this study, we simulated the photoaging process of flame retardant-added EPS (FR-EPS) and common original EPS (OR-EPS) microplastic (MP) particles with and without methyl octabromoether flame retardant (MOBE) in the laboratory to explore the effect of MOBE on the photodegradation of EPS. Results showed that MOBE accelerated size reduction and surface hole formation on the particles, hastening the shedding and replacement of particle surfaces. FR-EPS particles exhibited a weight loss exceeding that of OR-EPS, reaching 40.85 ± 3.72% after 36 days of irradiation. Moreover, rapid physical peeling of the FR-EPS surface was accompanied by continuous chemical oxidation and fluctuations of the carbonyl index and O/C ratio. A diffusion model based on Fick's second law fitted well for the concentration of MOBE remaining in FR-EPS particles. MOBE's sensitivity to direct photochemical reactions inhibited the early-stage photoaging of EPS MP particles by competing for photons. However, MOBE as chromophores could absorb photons and produce •OH to promote the aging of EPS. Moreover, the capacity of EPS to absorb light energy also accelerated MOBE degradation. These findings suggested that the photoaging behavior of commercial EPS products containing flame retardants in the environment is quite different from that of pure EPS, indicating that additive-plastic interactions significantly alter MP fate and environmental risks.

Predictive modeling of plastic pyrolysis process for the evaluation of activation energy: Explainable artificial intelligence based comprehensive insights.

Pyrolysis, a thermochemical conversion approach of transforming plastic waste to energy has tremendous potential to manage the exponentially increasing plastic waste. However, understanding the process kinetics is fundamental to engineering a sustainable process. Conventional analysis techniques do not provide insights into the influence of characteristics of feedstock on the process kinetics. Present study exemplifies the efficacy of using machine learning for predictive modeling of pyrolysis of waste plastics to understand the complexities of the interrelations of predictor variables and their influence on activation energy. The activation energy for pyrolysis of waste plastics was evaluated using machine learning models namely Random Forest, XGBoost, CatBoost, and AdaBoost regression models. Feature selection based on the multicollinearity of data and hyperparameter tuning of the models utilizing RandomizedSearchCV was conducted. Random forest model outperformed the other models with coefficient of determination (R2) value of 0.941, root mean square error (RMSE) value of 14.69 and mean absolute error (MAE) value of 8.66 for the testing dataset. The explainable artificial intelligence-based feature importance plot and the summary plot of the shapely additive explanations projected fixed carbon content, ash content, conversion value, and carbon content as significant parameters of the model in the order; fixed carbon > carbon > ash content > degree of conversion. Present study highlighted the potential of machine learning as a powerful tool to understand the influence of the characteristics of plastic waste and the degree of conversion on the activation energy of a process that is essential for designing the large-scale operations and future scale-up of the process.

Everything falls apart: How solids degrade and release nanomaterials, composite fragments, and microplastics.

To ensure the safe use of materials, one must assess the identity and quantity of exposure. Solid materials, such as plastics, metals, coatings and cements, degrade to some extent during their life cycle, and releases can occur during manufacturing, use and end-of-life. Releases (e.g., what is released, how does release happen, and how much material is released) depend on the composition and internal (nano)structures of the material as well as the applied stresses during the lifecycle. We consider, in some depth, releases from mechanical, weathering and thermal stresses and specifically address the use cases of fused-filament 3D printing, dermal contact, food contact and textile washing. Solid materials can release embedded nanomaterials, composite fragments, or micro- and nanoplastics, as well as volatile organics, ions and dissolved organics. The identity of the release is often a heterogenous mixture and requires adapted strategies for sampling and analysis, with suitable quality control measures. Control materials enhance robustness by enabling comparative testing, but reference materials are not always available as yet. The quantity of releases is typically described by time-dependent rates that are modulated by the nature and intensity of the applied stress, the chemical identity of the polymer or other solid matrix, and the chemical identity and compatibility of embedded engineered nanomaterials (ENMs) or other additives. Standardization of methods and the documentation of metadata, including all the above descriptors of the tested material, applied stresses, sampling and analytics, are identified as important needs to advance the field and to generate robust, comparable assessments. In this regard, there are strong methodological synergies between the study of all solid materials, including the study of micro- and nanoplastics. From an outlook perspective, we review the hazard of the released entities, and show how this informs risk assessment. We also address the transfer of methods to related issues such as tyre wear, advanced materials and advanced manufacturing, biodegradable polymers, and non-solid matrices. As the consideration of released entities will become more routine in industry via lifecycle assessment in Safe-and-Sustainable-by-Design practices, release assessments will require careful design of the study with quality controls, the use of agreed-on test materials and standardized methods where these exist and the adoption of clearly defined data reporting practices that enable data reuse, meta-analyses, and comparative studies.

Cellulose-based biomass composite films for plastic replacement: Synergistic UV shielding, antibacterial and antioxidant properties.

With the gradual increase in environmental awareness and the growing demand for food safety, sustainable and environmentally friendly cellulose-based materials have become a promising alternative to petroleum-based plastics. However, in practice, packaging materials prepared from cellulose-based materials still have some unsatisfactory properties, such as monofunctionality, low transparency, and lack of UV shielding, antibacterial or antioxidant properties. Herein, a novel synthetic strategy is proposed in this paper, specifically, tannic acid (TA), a green natural extract with antibacterial and antioxidant properties, is used as a plasticizer and cross-linker, and oxidized cellulose nanocellulose (TOCN) modified with folic acid (FA) grafting is blended with TA, and cellulose-based biomass thin films with ultraviolet (UV) shielding, antibacterial, and antioxidant properties have been successfully prepared by using a simple vacuum-assisted filtration. The experimental results showed that the films could completely block ultraviolet light at wavelengths of 200-400 nm while providing 81.47 % transparency in the visible spectrum, while the introduction of TA conferred excellent antibacterial and antioxidant capabilities with antioxidant activity of up to 95 %, and also resulted in films with excellent mechanical properties. Therefore, this work provides ideas for the design and manufacture of competitive biomass green packaging materials, laying the foundation for future applications in food packaging.

Recent advances in the relationships between biofilms and microplastics in natural environments.

Plastic pollution in the form of microplastics (MPs), poses a significant threat to natural ecosystems, with detrimental ecological, social, and economic impacts. This review paper aims to provide an overview of the existing research on the interaction between microbial biofilms and MPs in natural environments. The review begins by outlining the sources and types of MPs, emphasizing their widespread presence in marine, freshwater, and terrestrial ecosystems. It then discusses the formation and characteristics of microbial biofilms on MPs surfaces, highlighting their role in altering the physicochemical properties of MPs and facilitating processes such as vertical transport, biodegradation, dispersion of microorganisms, and gene transfer. Different methods used to assess these interactions are discussed, including microbiological and physicochemical characterization. Current gaps and challenges in understanding the complex relationships between biofilms and MPs are identified, highlighting the need for further research to elucidate the mechanisms underlying these complex interactions and to develop effective mitigation strategies. Innovative solutions, including bioremediation techniques and their combination with other strategies, such as nanotechnology, advanced filtration technologies, and public awareness campaigns, are proposed as promising approaches to address the issue of MPs pollution. Overall, this review underscores the urgent need for a multidisciplinary approach to combating MPs pollution, combining scientific research, technological innovation, and public engagement to safeguard the health and integrity of natural ecosystems.

Phthalates and other organic chemicals in agricultural soils after use of different types of conventional and biodegradable plastics.

Various plastic materials are used in contact with agricultural soil, like mulching films, crop covers, weed controlling fabrics and nets. Polyethylene (PE) mulches have already been recognized as a significant source of plastic in soil and they have been shown to contain additives like phthalates, known as endocrine disruptors. However, other agricultural plastics are less studied, and little is known on the substances potentially released from them endangering biodiversity and the human health. This research aims to assess whether different agricultural plastics release additives into soil and to compare the release among various materials. We collected soil samples from 38 agricultural fields where conventional mulching films (PE), weed controlling fabrics (PP), biodegradable mulches based on polybutylene adipate terephthalate (PBAT), frost covers (PP), and oxo-degradable films (at least OXO-PE) were used. We analyzed the soils for phthalates and acetyl tributyl citrate (ATBC), used as plastic additives, and for polycyclic aromatic hydrocarbons (PAH) and dodecane that have high affinity for plastics. In comparison to the control soils, dibutylphthalate (DBP) and ATBC concentrations were significantly higher in soils mulched with PE and, partly, with biodegradable films. DBP concentration found in soil samples ranged between below the limit of quantification at a control site (1.5 µg kg-1) to 135 µg kg-1 at a site mulched with OXO-PE. The highest ATBC concentration, 22 ± 6 µg kg-1, was registered in a site mulched with PE, showing a statistically significant difference not only in comparison to the controls but also when compared to sites mulched with OXO-PE (p = 0.029) and PBAT (p < 0.009). On the contrary, the use of agricultural plastics did not influence the concentration of PAHs and dodecane. Our results indicate that agricultural plastics are a source of some organic chemicals to agricultural soils, including phthalates that are known for posing threat to soil ecosystem and human health.

Bovine Serum Albumin Bends Over Backward to Interact with Aged Plastics: A Model for Understanding Protein Attachment to Plastic Debris.

Plastic pollution, a major environmental crisis, has a variety of consequences for various organisms within aquatic systems. Beyond the direct toxicity, plastic pollution has the potential to absorb biological toxins and invasive microbial species. To better understand the capability of environmental plastic debris to adsorb these species, we investigated the binding of the model protein bovine serum albumin (BSA) to polyethylene (PE) films at various stages of photodegradation. Circular dichroism and fluorescence studies revealed that BSA undergoes structural rearrangement to accommodate changes to the polymer's surface characteristics (i.e., crystallinity and oxidation state) that occur as the result of photodegradation. To understand how protein structure may inform docking of whole organisms, we studied biofilm formation of bacteriaShewanella oneidensison the photodegraded PE. Interestingly, biofilms preferentially formed on the photodegraded PE that correlated with the state of weathering that induced the most significant structural rearrangement of BSA. Taken together, our work suggests that there are optimal physical and chemical properties of photodegraded polymers that predict which plastic debris will carry biochemical or microbial hitchhikers.

An assessment of microplastic contamination in beach sediment of Maharashtra State, India, with special reference to anthropogenic activities.

The escalating issue of microplastic (MP) pollution poses a significant threat to the marine environment due to increasing plastic production and improper waste management. The current investigation was aimed at quantifying the MP concentration on 25 beaches on the Maharashtra coast, India. Beach sediments (1 kg) were collected from each site, with five replicates to evaluate the extent of MPs. The samples were homogenized, and three 20 g replicas were prepared for subsequent analysis. Later, the samples were sieved, and MPs were extracted using previously published protocols. The abundance of MPs found as 1.56 ± 0.79 MPs/g, ranges from 0.43 ± 0.07 to 3 ± 0.37 MPs/g. Fibers were found as the most abundant shape of MPs. Size-wise classification revealed dominance of <1 mm and 1-2 mm-sized MPs. Blue- and black-colored MPs were recorded dominantly. Polymer identification of MPs revealed polyurethane, polypropylene, polyvinyl chloride, acrylic or polymethyl methacrylate, and rubber. The findings revealed that MPs were found to be higher at highly impacted sites, followed by moderately impacted sites and low-impacted sites, possibly due to a different degree of anthropogenic pressure. The study recommended the urgent need for effective policy to prevent plastics accumulation in the coastal environment of Maharashtra State, India. PRACTITIONER POINTS: The study investigated the abundance and distribution of microplastics in the marine environment, specifically in sediments. The most common type of microplastic found was fibers, followed by fragments and films. Microplastics were found to pose a potential risk to the marine ecosystem, although further research is needed to fully understand their ecological impact. Future research should focus on expanding the sample size, assessing long-term effects, exploring sources and pathways, and considering size and shape of microplastics. The findings recommended urgent action to mitigate plastic pollution in Maharashtra coast.