A portable inflatable soft wearable robot to assist the shoulder during industrial work.

Repetitive overhead tasks during factory work can cause shoulder injuries resulting in impaired health and productivity loss. Soft wearable upper extremity robots have the potential to be effective injury prevention tools with minimal restrictions using soft materials and active controls. We present the design and evaluation of a portable inflatable shoulder wearable robot for assisting industrial workers during shoulder-elevated tasks. The robot is worn like a shirt with integrated textile pneumatic actuators, inertial measurement units, and a portable actuation unit. It can provide up to 6.6 newton-meters of torque to support the shoulder and cycle assistance on and off at six times per minute. From human participant evaluations during simulated industrial tasks, the robot reduced agonist muscle activities (anterior, middle, and posterior deltoids and biceps brachii) by up to 40% with slight changes in joint angles of less than 7% range of motion while not increasing antagonistic muscle activity (latissimus dorsi) in current sample size. Comparison of controller parameters further highlighted that higher assistance magnitude and earlier assistance timing resulted in statistically significant muscle activity reductions. During a task circuit with dynamic transitions among the tasks, the kinematics-based controller of the robot showed robustness to misinflations (96% true negative rate and 91% true positive rate), indicating minimal disturbances to the user when assistance was not required. A preliminary evaluation of a pressure modulation profile also highlighted a trade-off between user perception and hardware demands. Finally, five automotive factory workers used the robot in a pilot manufacturing area and provided feedback.

Comparing shoulder proprioception, upper extremity dynamic stability, and hand grip strength in overhead athletes with and without scapular dyskinesis.

INTRODUCTION: Scapular dyskinesis is prevalent among asymptomatic athletes, particularly those involved in overhead activities, and can significantly impact their neuromuscular control. These changes may impair upper extremity function and strength, elevating the risk of injury. Therefore, it is imperative to investigate how scapular dyskinesis affects shoulder proprioception, upper extremity dynamic stability, and hand grip strength in overhead athletes. This study compared these parameters between overhead athletes with and without scapular dyskinesis. METHODS: The study included twenty asymptomatic professional overhead athletes with scapular dyskinesis and twenty without scapular dyskinesis, identified using the lateral scapular slide test. In this cross-sectional study, shoulder active joint position sense, serving as shoulder proprioception, was measured using an isokinetic dynamometer. Upper extremity dynamic stability and hand grip strength were evaluated using an upper quarter modified star excursion balance test (UQ-mSEBT) and a handheld dynamometer. RESULTS: The study found that the shoulder active joint position sense was significantly lower in the scapular dyskinesis group compared to the group without scapular dyskinesis (PExternal Rotation = 0.003, PInternal Rotation < 0.001, and PForward Flexion = 0.002). However, the two groups had no significant differences in UQ-mSEBT and hand grip strength scores. CONCLUSIONS: The results showed that scapular dyskinesis could affect the sense of shoulder active joint position among asymptomatic overhead athletes. However, it did not affect their upper extremity dynamic stability and hand grip strength.

Factors determining the short-term clinical outcomes of conservative treatment in patients with supraspinatus tear.

INTRODUCTION: To identify factors influencing the better and worse changes in the Western Ontario Rotator Cuff Index of patients undergoing conservative treatment for supraspinatus tendon tear. METHODS: The study included 30 patients with supraspinatus tendon tear who underwent conservative treatment. The average duration of intervention was 35.4 days. The Western Ontario Rotator Cuff Index, shoulder range of motion, isometric muscle strength, supraspinatus tendon thickness, thickness of the supraspinatus, infraspinatus, and teres minor muscles, and acromiohumeral interval were assessed before and after the intervention. In the statistical analyses, change in the Western Ontario Rotator Cuff Index was the dependent variable, and the amount of change in each measurement variable before and after the intervention was the independent variable. RESULTS: The average Western Ontario Rotator Cuff Index improved from 1067 at pre-treatment to 997 at post-treatment, but without a significant difference (p = 0.29). A multiple regression analysis revealed that supraspinatus tendon thickness and muscle strength in shoulder external rotation at 90° scaption had a significant effect on the change in the Western Ontario Rotator Cuff Index (R2 = 0.44, p < 0.01). CONCLUSION: Supraspinatus tendon thickness and muscle strength in shoulder external rotation at 90° scaption were important factors for the Western Ontario Rotator Cuff Index score in the early stages of conservative treatment for patients with supraspinatus tendon tear.

Exercises with the StretchPole improve shoulder joint range of motion.

The 'StretchPole' foam roller product is mainly used to loosen muscle groups and joints in the deeper layers of the body that are normally inaccessible to the human hand, and to realign the skeletal structure by lying on the pole and performing exercises. It is also used to strengthen the core, which plays an important role in postural maintenance and stability. The purpose of this study was to determine the effects of the 'Solacon' exercise routine using a StretchPole on shoulder joint range of motion. Forty healthy participants performed Solacon exercises using a StretchPole. The specific method of Solacon comprises six movements: (1) chest slide, (2) crescent, (3) cone, (4) twister, (5) shoulder alternating rotation, and (6) chin-in exercise. The joint range of motion of the bilateral shoulder joint flexion, abduction, horizontal abduction, and external rotation (1st and 2nd) were measured before and after the exercises. All measures were significantly higher after exercise compared to before exercise. Solacon exercises improve thoracic spine and scapular mobility and stretch the anterior thoracic muscle groups. The shoulder joint in the broad sense consists of the humerus, scapula, clavicle, sternum, and ribs. These in turn constitute the scapulohumeral joint, acromioclavicular joint, sternoclavicular joint, scapulothoracic joint and functional second shoulder joint. In addition, costovertebral joints and intervertebral joints are also involved because of the added motion of the ribs and the spine. We considered that the ranges of motion of shoulder joint flexion, abduction, horizontal abduction, and external rotation measured in this study were expanded.

Deep squat test - Functional movement Screen: Convergent validity and ability to discriminate subjects with different levels of joint mobility.

BACKGROUND: Functional Movement Screen (FMS) is an important tool in the assessment of exercise practice. Assuming FMS lacks precise validity for assessing postural deficits, further research is needed to assess whether it is a sufficiently precise tool for analysing joint mobility. Research aims were to evaluate: convergent validity of Deep Squat (DS) - one of FMS tests - regarding joint mobility, using data from a three-dimensional motion analysis as a comparable method; DS's ability to discriminate between subjects with different joint mobility levels. METHODS: Sixty subjects were selected (23.6 ± 3.8 years). DS was performed according to FMS guidelines. Subjects' performance in frontal and sagittal planes was recorded by two video cameras and subsequently scored by two FMS-certified evaluators. Three-dimensional motion analyses of DS were acquired by a Vicon Motion Capture System (200 Hz). Ten trials were acquired for each subject. Ankle, knee, hip, and shoulder angular positions in sagittal plane were determined from the FullBody PlugInGait model. Spearman's coefficient examined the correlation between angular positions and DS score. Kruskal-Wallis test was used to assess the DS ability to discriminate between subjects with different joint mobility levels by comparing different scores. RESULTS: Negligible to moderate correlations were found between DS score and angular positions (-0.5 < r < 0.5). Only shoulder angular positions showed differences between score "1" and "2" (p < 0.05). Shoulder and hip angular positions showed no differences between score "2" and "3" (p < 0.05). CONCLUSIONS: DS yielded low convergent validity regarding joint mobility and did not show the ability to discriminate between subjects with different joint mobility levels.

Estimation of Shoulder Joint Rotation Angle Using Tablet Device and Pose Estimation Artificial Intelligence Model.

Traditionally, angle measurements have been performed using a goniometer, but the complex motion of shoulder movement has made these measurements intricate. The angle of rotation of the shoulder is particularly difficult to measure from an upright position because of the complicated base and moving axes. In this study, we attempted to estimate the shoulder joint internal/external rotation angle using the combination of pose estimation artificial intelligence (AI) and a machine learning model. Videos of the right shoulder of 10 healthy volunteers (10 males, mean age 37.7 years, mean height 168.3 cm, mean weight 72.7 kg, mean BMI 25.6) were recorded and processed into 10,608 images. Parameters were created using the coordinates measured from the posture estimation AI, and these were used to train the machine learning model. The measured values from the smartphone's angle device were used as the true values to create a machine learning model. When measuring the parameters at each angle, we compared the performance of the machine learning model using both linear regression and Light GBM. When the pose estimation AI was trained using linear regression, a correlation coefficient of 0.971 was achieved, with a mean absolute error (MAE) of 5.778. When trained with Light GBM, the correlation coefficient was 0.999 and the MAE was 0.945. This method enables the estimation of internal and external rotation angles from a direct-facing position. This approach is considered to be valuable for analyzing motor movements during sports and rehabilitation.

Are the shoulder joint function, stability, and mobility tests predictive of handstand execution?

Handstand is a basic element common across gymnastic disciplines and physical education classes that is frequently evaluated for quality in competition or skill acquisition. The correct handstand execution relies on maintaining balance, for which the shoulders seem particularly important. This study explores the relationship between shoulder joint function and the quality of handstand execution in novice college athletes (n = 111; aged 19-23 years). We assessed the shoulder joint function using standardized field tests (Upper Quarter Y Balance Test and Closed Kinetic Chain Upper Extremity Stability Test) and evaluated handstand execution on official rating scale. Ordinal logistic regression models showed no relationship between the quality of handstand execution (E-score) and measures of shoulder joint stability or mobility in our sample (POR = 0.97 [0.91, 1.03] and 1.00 [0.91, 1.09] for E-score). Two major factors may have caused an observed pattern of results. Firstly, the standardized tests assess shoulder joints in different loads and ranges of motion compared to handstands. Secondly, our novice sample was not able to perform the handstand sufficiently well. In our sample of novice college athletes, shoulder function seems not related to handstand execution as other latent factors hindered their performance.

Older age is associated with decreased overall shoulder strength but not direction-specific differences in the three-dimensional feasible torque space.

Shoulder strength is reduced in older adults but has only been assessed in planar motions that do not reflect the diverse requirements of daily tasks. We quantified the impact of age on strength spanning the three degrees of freedom relevant to shoulder function, referred to as the feasible torque space. We hypothesized that the feasible torque space would differ with age and expected this age-effect to reflect direction-specific deficits. We measured strength in 32 directions to characterize the feasible torque space of the shoulder in participants without shoulder pain or tendinous pathology (n = 39, 19-86 years). We modeled the feasible torque space for each participant as an ellipsoid, computed the ellipsoid size and direction-specific metrics (ellipsoid position, orientation, and shape), and then tested the effect of age on each metric. Age was negatively associated with ellipsoid size (a measure of overall strength magnitude; -0.0033 ± 0.0007 (Nm/kg)/year, p < 0.0001). Contrary to our expectation, the effect of age on the direction-specific metrics did not reach statistical significance. The effect of age did not differ significantly between male and female participants. Three-dimensional strength measurements allowed us to constrain the direction of participants' maximum torque production and characterize the entire feasible torque space. Our findings support a generalized shoulder strengthening program to address age-related shoulder weakness in those without pain or pathology. Clinical exam findings of imbalanced weakness may suggest underlying pathology beyond an effect of age. Longitudinal studies are needed to determine the positive or negative impact of our results.

An Analysis of Intrapitch Variation in Joint and Segment Velocities With Throwing Arm Kinetics in High School and Professional Baseball Pitchers.

BACKGROUND: Improper sequencing order of maximal joint and segment velocities has been identified as an important predictor for both throwing arm kinetics and ball velocity. PURPOSE: To investigate the intrapitcher variation of maximal segment velocities and the relationship to throwing arm kinetics and ball velocity in high school (HS) and professional (PRO) pitchers. STUDY DESIGN: Descriptive laboratory study. METHODS: HS (n = 59) and PRO (n = 338) pitchers, instructed to throw 8 to 12 fastball pitches, were evaluated with 3-dimensional motion capture (480 Hz). Maximal joint and segment velocities were calculated for each pitch, and the standard deviation of the maxima was calculated per pitcher. These standard deviations were used to classify pitchers as "low variance" or "high variance" for each segmental velocity subgroup, "overall low variance" or "overall high variance" based on cumulative segment velocity variation, or "population," with any pitcher eligible to be included in multiple subcategories. Maximal velocities and throwing arm kinetics were compared among the various subgroups. RESULTS: The HS low-variance shoulder internal rotation velocity subgroup (4949 ± 642 deg/s) had significantly lower maximal shoulder internal rotation velocity compared with HS population (5774 ± 1057 deg/s) (P < .001); similar findings were observed for PROs (5269 ± 835 vs 5824 ± 1076 deg/s; P < .001), as well as lower shoulder superior force compared with the PRO population (14.8% ± 8.8% vs 17.8% ± 8.8% body weight; P = .001). The PRO low-variance lead knee extension velocity subgroup had significantly lower maximal lead knee extension velocity (216 ± 135 vs 258 ± 125 deg/s; P = .001) and shoulder distractive force (111.5% ± 14.4% vs 115.6% ± 15.9% body weight; P = .003) compared with the PRO population. The PRO overall low-variance subgroup had significantly lower shoulder distractive force (111.8% ± 14.1% vs 119.6% ± 15.5% body weight; P = .008) and elbow anterior force (40.6% ± 5.0% vs 43.6% ± 6.2% body weight; P = .008) compared with the PRO overall high-variance subgroup. CONCLUSION: HS and PRO pitchers with low variance for joint and segment velocities achieved significantly lower maximal velocities in the subgroup of interest, while preserving ball velocity. PRO pitchers with overall low variance among multiple maximal joint and segment velocities demonstrated decreased shoulder distractive and elbow anterior force. CLINICAL RELEVANCE: PRO pitchers with low intrapitch variation in maximal joint and segment velocities may be viewed as kinetically conservative throwers. These pitchers with similarly maintained mechanics between pitches may have an increasingly regimented form that preserves kinetic forces about the throwing arm. The opposite may be true for PRO pitchers with increased variability in segmental velocities during their pitching motion, as they showed increased throwing arm kinetics including shoulder distractive and elbow anterior force compared with the overall low-variance group, theoretically increasing their risk of injury.

Development of a musculoskeletal shoulder model considering anatomic joint structures and soft-tissue deformation for dynamic simulation.

The shoulder joint has a high degree of freedom and an extremely complex and unstable kinematic mechanism. Coordinated contraction of the rotator cuff muscles that stop around the humeral head and the deltoid muscles and the extensibility of soft tissues, such as the joint capsule, labrum, and ligaments, contribute to shoulder-joint stability. Understanding the mechanics of shoulder-joint movement, including soft-tissue characteristics, is important for disease prevention and the development of a device for disease treatment. This study aimed to create a musculoskeletal shoulder model to represent the realistic behavior of joint movement and soft-tissue deformation as a dynamic simulation using a rigid-body model for bones and a soft-body model for soft tissues via a spring-damper-mass system. To reproduce the muscle-contraction properties of organisms, we used a muscle-expansion representation and Hill's mechanical muscle model. Shoulder motion, including the movement of the center of rotation in joints, was reproduced, and the strain in the joint capsule during dynamic shoulder movement was quantified. Furthermore, we investigated narrowing of the acromiohumeral distance in several situations to induce tissue damage due to rotator cuff impingement at the anterior-subacromial border during shoulder abduction. Given that the model can analyze exercises under disease conditions, such as muscle and tendon injuries and impingement syndrome, the proposed model is expected to help elucidate disease mechanisms and develop treatment guidelines.

Tacklers' shoulder abduction and flexion at contact alter when engaging in different front-on, one-on-one tackle instructions from an expert coach.

OBJECTIVES: To ascertain how the three-dimensional shoulder kinematics of tacklers alter when performing four legal types of front-on, one-on-one, rugby-style torso tackles. DESIGN: Controlled laboratory study. METHODS: Three-dimensional motion capture measured 15 male amateur-level rugby code players (24.3 ±â€¯6.1 years) who were instructed by an expert coach to perform four sets of 10 front-on, one-on-one tackles. Four sets comprised two smother and two dominant tackles: two based on the Australian National Rugby League coaching manual (Dominant NRL, Smother NRL); and two modifications via increasing the contact height from the lower- to mid-torso (Dominant, Torso Stick) or from the upper- to mid-upper torso with a vertical 'pop action' that changes the way the tackler contacted the ball carrier's upper torso (Smother, Pop, Lock). Mixed general linear models were applied. RESULTS: Greater shoulder abduction, flexion and internal rotation were displayed by the DNRL tackle technique than in any other technique (p < 0.001). At contact, the Smother and Dominant NRL (p < 0.03) showed greater head-uptrunk contralateral rotation away from the tackle than the Smother, Pop, Lock. CONCLUSIONS: Tacklers modified the way they positioned their shoulder joint when engaging in legal front-on, one-on-one tackles with different tackle instructions. More prominent positions of shoulder abduction and flexion, and head-uptrunk contralateral rotation were observed when executing the traditional tackle techniques (Smother NRL, Dominant NRL) as opposed to two variants of these (Smother, Pop, Lock, Dominant, Torso Stick). Inclusion of tackle specific coaching instructions provides emerging scientific evidence to support revised coaching tackling technique interventions that might enhance player safety.

Affordances for throwing: An uncontrolled manifold analysis.

Movement systems are massively redundant, and there are always multiple movement solutions to any task demand; motor abundance. Movement consequently exhibits 'repetition without repetition', where movement outcomes are preserved but the kinematic details of the movement vary across repetitions. The uncontrolled manifold (UCM) concept is one of several methods that analyses movement variability with respect to task goals, to quantify repetition without repetition and test hypotheses about the control architecture producing a given abundant response to a task demand. However, like all these methods, UCM is under-constrained in how it decomposes a task and performance. In this paper, we propose and test a theoretical framework for constraining UCM analysis, specifically the perception of task-dynamical affordances. Participants threw tennis balls to hit a target set at 5m, 10m or 15m, and we performed UCM analysis on the shoulder-elbow-wrist joint angles with respect to variables derived from an affordance analysis of this task as well as more typical biomechanical variables. The affordance-based UCM analysis performed well, although data also showed thrower dynamics (effectivities) need to be accounted for as well. We discuss how the theoretical framework of affordances and affordance-based control can be connected to motor abundance methods in the future.

Surgeon Upper Extremity Kinematics During Error and Error-Free Retropubic Trocar Passage.

INTRODUCTION AND HYPOTHESIS: Surgeon kinematics play a significant role in the prevention of patient injury. We hypothesized that elbow extension and ulnar wrist deviation are associated with bladder injury during simulated midurethral sling (MUS) procedures. METHODS: We used motion capture technology to measure surgeons' flexion/extension, abduction/adduction, and internal/external rotation angular time series for shoulder, elbow, and wrist joints. Starting and ending angles, minimum and maximum angles, and range of motion (ROM) were extracted from each time series. We created anatomical multibody models and applied linear mixed modeling to compare kinematics between trials with versus without bladder penetration and attending versus resident surgeons. A total of 32 trials would provide 90% power to detect a difference. RESULTS: Out of 85 passes, 62 were posterior to the suprapubic bone and 20 penetrated the bladder. Trials with versus without bladder penetration were associated with more initial wrist dorsiflexion (-27.32 vs -9.03°, p = 0.01), less final elbow flexion (39.49 vs 60.81, p = 0.03), and greater ROM in both the wrist (27.48 vs 14.01, p = 0.02), and elbow (20.45 vs 12.87, p = 0.04). Wrist deviation and arm pronation were not associated with bladder penetration. Compared with attendings, residents had more ROM in elbow flexion (14.61 vs 8.35°, p < 0.01), but less ROM in wrist dorsiflexion (13.31 vs 20.33, p = 0.02) and arm pronation (4.75 vs 38.46, p < 0.01). CONCLUSIONS: Bladder penetration during MUS is associated with wrist dorsiflexion and elbow flexion but not internal wrist deviation and arm supination. Attending surgeons exerted control with the wrist and forearm, surgical trainees with the elbow. Our findings have direct implications for MUS teaching.

The associations of physical parameters with the Closed Kinetic Chain Upper Extremity Stability Test, the Upper Quarter Y Balance Test, and the Upper Limb Rotation Test in professional overhead athletes.

OBJECTIVE: To investigate the associations of glenohumeral internal (IR) and external rotation (ER), horizontal adduction (HA), and thoracic spine rotation ranges of motion (ROM), isometric muscle strength of the shoulder rotators, and trunk muscle endurance with the Closed Kinetic Chain Upper Extremity Stability Test (CKCUEST), the Upper Quarter Y Balance Test (YBT-UQ), and the Upper Limb Rotation Test (ULRT) in overhead athletes. DESIGN: Cross-sectional study. SETTINGS: Laboratory. PARTICIPANTS: One hundred twenty-one athletes were enrolled. MAIN OUTCOME MEASURES: Independent variables were: IR, ER, HA, and thoracic spine rotation ROMs, isometric muscle strength of glenohumeral IR and ER muscles, and trunk muscle endurance. Dependent variables were: CKCUEST, YBT-UQ, ULRT. RESULTS: IR ROM of the nondominant side was associated with the CKCUEST, the YBT-UQ, and the ULRT. IR muscle strength of the dominant side was associated with the CKCUEST and the ULRT. Trunk flexor and lateral endurance of the dominant side were associated with the CKCUEST and the YBT-UQ, respectively. CONCLUSIONS: Many of the physical parameters influencing scores on the CKCUEST and the YBT-UQ are different. Common parameters influence the CKCUEST and ULRT scores, yet more parameters influence the CKCUEST score. We suggest the combined use of the CKCUEST and the YBT-UQ in overhead athletes.

Shoulder viscoelasticity in a raptor-inspired model alleviates instability and enhances passive gust rejection.

Recent experiments with gliding raptors reveal a perplexing dichotomy: remarkably resilient gust rejection, but, at the same time, an exceptionally high degree of longitudinal instability. To resolve this incompatibility, a multiple degree of freedom model is developed with minimal requisite complexity to examine the hypothesis that the bird shoulder joint may embed essential stabilizing and preflexive mechanisms for rejecting rapid perturbations while simplifying and reducing control effort. Thus, the formulation herein is centrally premised upon distinct wing pitch and body pitch angles coupled via a Kelvin-Voigt viscoelastic shoulder joint. The model accurately exhibits empirical gust response of an unstable gliding raptor, generates biologically plausible equilibrium configurations, and the viscoelastic shoulder coupling is shown to drastically alleviate the high degree of instability predicted by conventional linear flight dynamics models. In fact, stability analysis of the model predicts a critical system timescale (the time to double amplitude of a pitch divergence mode) that is commensurate within vivomeasured latency of barn owls (Tyto alba). Active gust mitigation is studied by presupposing the owl behaves as an optimal controller. The system is under-actuated and the feedback control law is resolved in the controllable subspace using a Kalman decomposition. Importantly, control-theoretic analysis precisely identifies what discrete gust frequencies may be rapidly and passively rejected versus disturbances requiring feedback control intervention.

Optimising safe margins in shoulder surgeries: a cadaveric study on brachial plexus nerves with anthropometric and movement correlation.

PURPOSE: Shoulder surgeries, vital for diverse pathologies, pose a risk of iatrogenic nerve damage. Existing literature lacks diverse bone landmark-specific nerve position data. The purpose of this study is to address this gap by investigating such relationships. METHOD: This cadaveric study examines axillary, radial and suprascapular nerves' relation with acromion, coracoid and greater tuberosity of the humerus (GT). It also correlates this data with humeral lengths and explores nerve dynamics in relation to arm positions. RESULTS: The mean distance from the axillary nerve to (i) GT was 4.38 cm (range 3.32-5.44, SD 0.53), (ii) acromion was 6.42 cm (range 5.03-7.8, SD 0.694) and (iii) coracoid process was 4.3 cm (range 2.76-5.84, SD 0.769). Abduction brought the nerve closer by 0.36 cm, 0.35 cm and 0.53 cm, respectively. The mean distance from radial nerve to (i) GT was 5.46 cm (range 3.78-7.14, SD 0.839), (ii) acromion was 7.82 cm (range 5.4-10.24, SD 1.21) and (iii) tip of the coracoid process was 6.09 cm (range 4.07-8.11 cm, SD 1.01). The mean distance from the suprascapular nerve to the acromion was 4.2 cm (range 3.1-5.4, SD 0.575). The mean humeral length was noted to be 27.83 cm (range 25.3-30.7, SD 1.13). There was no significant correlation between these distances and humeral lengths. CONCLUSION: It is essential to exercise caution to avoid axillary nerve damage during the abduction manoeuvre, as its distance from the greater tuberosity and tip of the coracoid process has shown a significant reduction. The safe margins, in relation to the length of the humerus and consequently the patient's stature, exhibit no significant variation. In situations where the greater tuberosity (GT) and the border of the acromion are inaccessible due to reasons such as trauma, the tip of the coracoid process can serve as a dependable bone landmark for establishing a secure surgical margin.

The influence of rotator cuff tear type and weight bearing on shoulder biomechanics in an ex vivo simulator experiment.

Glenohumeral biomechanics after rotator cuff (RC) tears have not been fully elucidated. This study aimed to investigate the muscle compensatory mechanism in weight-bearing shoulders with RC tears and asses the induced pathomechanics (i.e., glenohumeral translation, joint instability, center of force (CoF), joint reaction force). An experimental, glenohumeral simulator with muscle-mimicking cable system was used to simulate 30° scaption motion. Eight fresh-frozen shoulders were prepared and mounted in the simulator. Specimen-specific scapular anthropometry was used to test six RC tear types, with intact RC serving as the control, and three weight-bearing loads, with the non-weight-bearing condition serving as the control. Glenohumeral translation was calculated using instantaneous helical axis. CoF, muscle forces, and joint reaction forces were measured using force sensors integrated into the simulator. Linear mixed effects models (RC tear type and weight-bearing) with random effects (specimen and sex) were used to assess differences in glenohumeral biomechanics. RC tears did not change the glenohumeral translation (p > 0.05) but shifted the CoF superiorly (p ≤ 0.005). Glenohumeral translation and joint reaction forces increased with increasing weight bearing (p < 0.001). RC and deltoid muscle forces increased with the presence of RC tears (p ≤ 0.046) and increased weight bearing (p ≤ 0.042). The synergistic muscles compensated for the torn RC tendons, and the glenohumeral translation remained comparable to that for the intact RC tendons. However, in RC tears, the more superior CoF was close to where glenoid erosion occurs in RC tear patients with secondary osteoarthritis. These findings underscore the importance of early detection and precise management of RC tears.

Benefits and limitations of isokinetic force assessments in swimmer's shoulders: A systematic review.

OBJECTIVE: To indicate the benefits and limitations of the isokinetic test results for the performance of the main shoulder joint movements in swimmers, considering the different competitive levels, swimming techniques, race distances, and sex. METHODS: Search on the PubMed, CENTRAL, Medline, LILACS, and SCOPUS databases for the oldest records up to October 2022. Risk of bias, methodological quality, and level of evidence were evaluated based on the NHLBI checklist. RESULTS: 29 articles met the criteria and were included in this study. The quality analysis classified three as "good" and 26 as "regular", with a KAPPA index of 0.87. The main benefits found involved assessments of the clinical condition of the shoulder joint complex, relationships with performance, and reliability studies. The limitations found point to the participant's positioning in the instrument, use of angular velocity above 180°/s, and sample size. CONCLUSION: The use of the isokinetic dynamometer allows verifying the levels of strength, endurance, balance, and asymmetries among swimmers of different techniques, distances, competitive levels, and sex. Thus, it helps in the analysis and monitoring of the clinical conditions of swimmers' shoulder joints, contributing to the decision-making process of physiotherapists and coaches.

Differences in Osseous Shoulder Morphology, Scapulothoracic Orientation, and Muscle Volume in Patients With Constitutional Static Posterior Shoulder Instability (Type C1) Compared With Healthy Controls.

BACKGROUND: Constitutional static posterior humeral decentering (type C1 according to ABC Classification) has been recognized as a pre-osteoarthritic deformity that may lead to early-onset posterior decentering osteoarthritis at a young age. Therefore, it is important to identify possible associations of this pathologic shoulder condition to find more effective treatment options. PURPOSE: To perform a comprehensive analysis of all parameters reported to be associated with a C1 shoulder-including the osseous shoulder morphology, scapulothoracic orientation, and the muscle volume of the shoulder girdle in a single patient cohort. STUDY DESIGN: Cross-sectional study; Level of evidence, 3. METHODS: A retrospective, comparative study was conducted analyzing 17 C1 shoulders in 10 patients who underwent magnetic resonance imaging (MRI) with the complete depiction of the trunk from the base of the skull to the iliac crest, including both humeri. The mean age of the patients was 33.5 years, and all patients were men. To measure and compare the osseous shoulder morphology (glenoid version, glenoid offset, humeral torsion, anterior acromial coverage, posterior acromial coverage, posterior acromial height, and posterior acromial tilt) and scapulothoracic orientation (scapular protraction, scapular internal rotation, scapular upward rotation, scapular translation, scapular tilt, and thoracic kyphosis), these patients were matched 1 to 4 according their age, sex, and affected side with shoulder-healthy patients who had received positron emission tomography (PET)-computed tomography. To measure and compare the muscle volume of the shoulder girdle (subscapularis, infraspinatus/teres minor, supraspinatus, trapezius, deltoid, latissimus dorsi/teres major, pectoralis major, and pectoralis minor), patients were matched 1 to 2 with patients who had received PET-MRI. Patients with visible pathologies of the upper extremities were excluded. RESULTS: The C1 group had a significantly higher glenoid retroversion, increased anterior glenoid offset, reduced humeral retrotorsion, increased anterior acromial coverage, reduced posterior acromial coverage, increased posterior acromial height, and increased posterior acromial tilt compared with controls (P < .05). Decreased humeral retrotorsion showed significant correlation with higher glenoid retroversion (r = -0.742; P < .001) and higher anterior glenoid offset (r = -0.757; P < .001). Significant differences were found regarding less scapular upward rotation, less scapular tilt, and less thoracic kyphosis in the C1 group (P < .05). The muscle volume of the trapezius and deltoid was significantly higher in the C1 group (P < .05). CONCLUSION: Patients with C1 shoulders differ from healthy controls regarding osseous scapular and humeral morphology, scapulothoracic orientation, and shoulder girdle muscle distribution. These differences may be crucial in understanding the delicate balance of glenohumeral centering.

Biomechanical Comparison Between Superior Capsular Reconstruction and Lower Trapezius Tendon Transfer in Irreparable Posterosuperior Rotator Cuff Tears.

BACKGROUND: Superior capsular reconstruction (SCR) and lower trapezius tendon transfer (LTT) have recently been used to manage irreparable posterosuperior rotator cuff tears (PSRCTs). There has been a paucity of comparative biomechanical considerations between the 2 procedures. PURPOSE: To compare the glenohumeral stability and biomechanical properties between SCR and LTT in PSRCTs involving the entire infraspinatus tendon region. STUDY DESIGN: Controlled laboratory study. METHODS: Eight fresh-frozen cadaveric shoulders were tested at 0°, 20°, and 40° of shoulder abduction. Maximum internal, external, and total humeral range of motion (ROM), superior translation of the humeral head, and subacromial contact characteristics were compared among 4 conditions: (1) intact rotator cuff, (2) PSRCTs involving the entire infraspinatus tendon region, (3) LTT using Achilles allograft (12 N and 24 N of loading), and (4) SCR using fascia lata allograft. RESULTS: Although a decrease in total ROM was noted in LTT with 12 N compared with the tear condition, LTT with both 12 N and 24 N as well as SCR did not restrict total rotational ROM compared with the intact condition. LTT had decreased total ROM compared with tear condition at 20° of abduction (P = .042), while no significant decrease was confirmed at all abduction angles after SCR. SCR and LTT with 24 N decreased superior translation compared with the PSRCT condition at 0° and 20° of abduction (P < .037) but not significantly at 40° of abduction, whereas LTT with a 24-N load decreased glenohumeral superior translation at all abduction angles (P < .039). Both SCR and LTT decreased subacromial contact pressure compared with the tear condition (P < .014) at all abduction angles. SCR decreased subacromial contact pressure at 0° and 40° of abduction (P = .019 and P = .048, respectively) compared with LTT with 12 N of loading, while there was no difference between SCR and LTT with 24 N of loading in all abduction angles. SCR increased the contact area compared with the PSRCT condition at all abduction angles (P < .023), whereas LTT did not increase the contact area. CONCLUSION: SCR and LTT decreased glenohumeral superior translation and contact pressure compared with PSRCT conditions. The LTT was superior to SCR in terms of superior translation of the humeral head at a higher shoulder abduction angle, whereas the SCR showed more advantageous subacromial contact characteristics compared with LTT. CLINICAL RELEVANCE: These biomechanical findings provide insights into these 2 fundamentally different procedures for the treatment of young and active patients with PSRCTs involving the entire infraspinatus tendon region.