RESUMEN
Solar cells are fabricated based on two new dyes. Dye acts as an additive to thin layer interface. The effect of the π-conjugated rigidity of the thiophene rings on the photovoltaic characteristics has been investigated. The structures of the dye 1 was based on dithieno [3,2-b:2',3'-d] thiophene-2-cyanoacrylic acid, while dye 2 was based on [2,2':5',2â³-terthiophene]-5-cyanoacrylic acid and were confirmed by elemental analysis, mass spectrometry, 1H NMR and 13C NMR spectral data. The P3HT/dye 1/nc-TiO2 solar cell produced the highest efficiency of 0.3 % with an open circuit voltage of 0.7 V compared to dye 2 solar cell. This has been attributed to the difference in energy levels of the dyes and location of their HOMO relative to conduction and valence bands of nc-TiO2. The dye 1 has rigid fused thiophene rings and its HOMO is located between valence band of TiO2 and HOMO of P3HT which leads to improve the charge carrier separation and increase the current density to reach 1.2 mA/cm2.
RESUMEN
Zirconium porous clay heterostructures (Zr-PCH) were synthesized using intercalated clay minerals by zirconium species with different contents of zirconium. The presence of zirconium and silica species was confirmed by X-ray diffraction, X-ray fluorescence, and magic-angle spinning nuclear magnetic resonance. The insertion of zirconium improved the thermal stability, the specific surface area with a maximum of 950 m2/g, and the acidity concentration of 0.993 mol of protons per g of solid. These materials were used to adsorb the basic blue-41 from aqueous solution. The adsorption efficiency was examined at different conditions, with a maximum adsorbed amount of 346 mg/g as estimated from Langmuir model. This value was dependent on zirconium content in the PCHs. The adsorption process was found to be favorable and spontaneous. The efficiency of the spent materials was maintained after five reuse cycles with a decrease by 15% of the original value for a particular Zr-PCH material with a Zr content of 6.82%. Single stage batch adsorber was suggested using the mass balance equation and Langmuir isotherm model. The amount of PCH materials required depended on the target percentage of adsorption at specific volume and initial concentration of the basic-blue-41 dye solution.
RESUMEN
The significance of the Fowler-Nordheim-type plots lies in the possibility of extracting useful and reliable physical parameters of the field electron emitters. This is achieved by the parameter's extraction methods. We report on the application of two parameters extraction methods on field emission data from bundles of carbon fibers (CFs) grouped in nickel tubes and operated inside a typical field emission microscope setup. These methods are the Murphy-Good plot and the conventional Fowler-Nordheim plot iterative method. The physical parameters include the area extraction parameter, the notional (actual) emission area, the formal area efficiency factor and the voltage conversion length. The results obtained from the two methods are discussed and compared to shed light on the controversial nature of these methods. The mechanism of field electron emission is analyzed based on the parameters extracted.
RESUMEN
The removal of Basic Blue-41 dye molecules was carried out by using two doped porous clay heterostructures by aluminum (Al) or zirconium (Zr) species. The proposed method of synthesis showed its efficiency, starting from Al or Zr intercalated hydrolyzed species, prior to its reaction with dodecylamine (C12 amine) and tetraethyl orthosilicate (TEOS) as a silica source. The intercalated precursors and their porous clay heterostructures (PCH) derivatives were characterized by different techniques. Solid NMR technique proved the presence of Al species into the intercalated silica between the clay sheets, and in addition to Si in different environments within the PCH materials. The Zr-PCH material exhibited a higher surface area and pore volume compared to its Al-PCH counterpart, with a mesoporous character for both materials. A maximum removed amount of 279 and 332 mg/g was achieved and deduced from the Langmuir equation. The regeneration tests revealed that the removal efficiency of Zr-PCH was retained after five regeneration runs, with a loss of 15% of the original value; meanwhile, the Al-PCH lost 45% of its efficiency after only three cycles. A single-stage batch design was proposed based on the Langmuir isotherm parameters. The increase of the removal capacity of Zr-PCH led to the reduction of the required amounts for the target removal of BB-41 dye compared to Al-PCH.
RESUMEN
A dye-sensitized solar cell was constructed on the basis of encapsulating the ruthenium polypyridyl photosensitizer Z907 in the macrocycle cucurbit[7]uril (CB7). The work focuses on the photophysical properties of the new host-guest complexes in acetonitrile and water (volume ratio 1:9) and on the top of nanocrystalline titanium dioxide (TiO2) electrode prior to the addition of poly(3-hexylthiophene) polymer and gold electrode. Complexation to CB7 in aqueous solutions has decreased the emission intensity and excited-state lifetime for metal-to-ligand charge transfer (MLCT) state at 650 nm by twofold because of collisional quenching, which opens a non-radiative deactivation channel. Similarly, a twofold decrease in the emission intensity and excited-state lifetime of MLCT at 750 nm on the top of TiO2 electrodes was observed with the addition of CB7. Encapsulation of Z907 dye to CB7 host has, also, led to fourfold enhancement in the short circuit current and power conversion efficiency of the final solar cell. The results support the premise that host-guest complexation of CB7 facilitates faster electron injection from Z907 dye into the conduction band of TiO2 electrodes.
RESUMEN
The performance of a dye-sensitized solar cell (DSSC) that is based on the host-guest encapsulation of 5-[4-diphenylamino)phenyl]thiophene-2-cyanoacrylic acid (L1) inside ß-cyclodextrin hosts has been tested. The formation of the complex in the solid state and when adsorbed on TiO(2) was characterized using steady and picosecond time-resolved emission techniques, as well as time dependent DFT calculations. The molecular-level insulation has led to a small enhancement in the energy-conversion performance of the fabricated DSSC with the best results being an increase in the open circuit voltage (Voc) from 0.7 to 0.8 V. The importance of the present investigation lies in the unique spectroscopic characterizations of the examined materials in the solid state.