The Effect of Divinylbenzene on the Structure and Properties of Polyethylene Films with Related Radiation Chemical Grafted Polystyrene and Sulfocationite Membranes.

In the present work, the effect of divinylbenzene (DVB) on the kinetics of post-radiation chemical graft polymerization styrene (St) on polyethylene (PE) film and its structural and morphological features were investigated. It has been found that the dependence of the degree of polystyrene (PS) grafting on the DVB concentration in the solution is extreme. An increase in the rate of graft polymerization at low concentrations of DVB in the solution is associated with a decrease in the mobility of the growing chains of PS. A decrease in the rate of graft polymerization at high concentrations of DVB is associated with a decrease in the rate of diffusion of St and iron(II) ions in the cross-linked network structure of macromolecules of graft PS. A comparative analysis of the IR transmission and multiple attenuated total internal reflection spectra of the films with graft PS shows that graft polymerization of St in the presence of DVB leads to the enrichment of the film surface layers in PS. These results have been confirmed by the data on the distribution of sulfur in these films after sulfonation. The micrographs of the surface of the grafted films show the formation of cross-linked local microphases of PS with fixed interfaces.

Scalable Synthesis and Characterization of Multilayer γ-Graphyne, New Carbon Crystals with a Small Direct Band Gap.

γ-Graphyne is the most symmetric sp2/sp1 allotrope of carbon, which can be viewed as graphene uniformly expanded through the insertion of two-carbon acetylenic units between all the aromatic rings. To date, synthesis of bulk γ-graphyne has remained a challenge. We here report the synthesis of multilayer γ-graphyne through crystallization-assisted irreversible cross-coupling polymerization. A comprehensive characterization of this new carbon phase is described, including synchrotron powder X-ray diffraction, electron diffraction, lateral force microscopy, Raman spectroscopy, infrared spectroscopy, and cyclic voltammetry. Experiments indicate that γ-graphyne is a 0.48 eV band gap semiconductor, with a hexagonal a-axis spacing of 6.88 Å and an interlayer spacing of 3.48 Å, which is consistent with theoretical predictions. The observed crystal structure has an aperiodic sheet stacking. The material is thermally stable up to 240 °C but undergoes transformation at higher temperatures. While conventional 2D polymerization and reticular chemistry rely on error correction through reversibility, we demonstrate that a periodic covalent lattice can be synthesized under purely kinetic control. The reported methodology is scalable and inspires extension to other allotropes of the graphyne family.

More Powerful Twistron Carbon Nanotube Yarn Mechanical Energy Harvesters.

Stretching a coiled carbon nanotube (CNT) yarn can provide large, reversible electrochemical capacitance changes, which convert mechanical energy to electricity. Here, it is shown that the performance of these "twistron" harvesters can be increased by optimizing the alignment of precursor CNT forests, plastically stretching the precursor twisted yarn, applying much higher tensile loads during precoiling twist than for coiling, using electrothermal pulse annealing under tension, and incorporating reduced graphene oxide nanoplates. The peak output power for a 1 and a 30 Hz sinusoidal deformation are 0.73 and 3.19 kW kg-1 , respectively, which are 24- and 13-fold that of previous twistron harvesters at these respective frequencies. This performance at 30 Hz is over 12-fold that of other prior-art mechanical energy harvesters for frequencies between 0.1 and 600 Hz. The maximum energy conversion efficiency is 7.2-fold that for previous twistrons. Twistron anode and cathode yarn arrays are stretched 180° out-of-phase by locating them in the negative and positive compressibility directions of hinged wine-rack frames, thereby doubling the output voltage and reducing the input mechanical energy.

Formation of Composite Coatings on Galvanized Steel from Organosilane Solutions Using Electrophoresis and Sol-Gel Technology.

New hybrid composite coatings (HCCs) on hot-dip galvanized steel (HDGS) were obtained using electrophoresis (cathodic polarization (CP)) and sol-gel technology. For this purpose, a technique for the preparation of a cationic precursor based on TiCl4 and aminopropyltriethoxysilane was developed. Electrophoresis of the charged particles of the precursor and organosilanes promotes the production of denser sol-gel coatings with improved adhesion. Using scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS) and electrochemical impedance spectroscopy (EIS) methods, the formation mechanism and protective properties of HCC on galvanized steel were investigated.

Mechanism of Post-Radiation-Chemical Graft Polymerization of Styrene in Polyethylene.

Structural and morphological features of graft polystyrene (PS) and polyethylene (PE) copolymers produced by post-radiation chemical polymerization have been investigated by methods of X-ray microanalysis, electron microscopy, DSC and wetting angles measurement. The studied samples differed in the degree of graft, iron(II) sulphate content, sizes of PE films and distribution of graft polymer over the polyolefin cross section. It is shown that in all cases sample surfaces are enriched with PS. As the content of graft PS increases, its concentration increases both in the volume and on the surface of the samples. The distinctive feature of the post-radiation graft polymerization is the stepped curves of graft polymer distribution along the matrix cross section. A probable reason for such evolution of the distribution profiles is related to both the distribution of peroxide groups throughout the sample thickness and to the change in the monomer and iron(II) salt diffusion coefficients in the graft polyolefin layer. According to the results of electron microscope investigations and copolymer wettability during graft polymerization, a heterogeneous system is formed both in the sample volume and in the surface layer. It is shown that the melting point, glass transition temperature and degree of crystallinity of the copolymer decreases with the increasing proportion of graft PS. It is suggested that during graft polymerization a process of PE crystallite decomposition (melting) and enrichment of the amorphous phase of graft polymer by fragments of PE macromolecules occurs spontaneously. The driving force of this process is the osmotic pressure exerted by the phase network of crystallites on the growing phase of the graft PS.

Adhesion and Energy Characteristics of Rigid-Chain Polymer Surface: Polyamidoimides.

The adhesion characteristics and surface energies of two series of polyamidoimides (PAI) with different molecular weights, monomer unit structures, hinge groups in the main chain of the macromolecules, and thermal prehistory were determined via delamination at 180° and test fluids contact angles. We found that PAI are high-energy polymers, the surface energy of which varies in the range from 32 to 45 mJ/m2. In contrast to flexible-chain polymers, the exponent in the McLeod equation is two, which is due to the flat parallel orientation of the macromolecular chains in the surface layers. The main contribution to the change in surface characteristics of these polymers is the change in the packing density of PAI macromolecules, which is reflected mainly in the change in the polymers' dispersion component. We found that the adhesion properties of PAI with respect to high- and low-energy substrates are determined mainly by the macromolecules packing density in the surface layers with their conformation state unchanged.

Shaping nanomaterials by short electrical pulses.

We report a new dry-state technique for non-contact patterning of nanostructured conducting materials, and demonstrate its use for carbon nanotube forests and freestanding sheets of carbon nanotubes, graphene, graphene sponge, and MXene. This method uses self-generated electron-emission pulses (∼20 ns) in air. On a substrate-tip separation scale of 10 to 20 nm, the few molecules of gas at atmospheric pressure enables electron-emission-based interaction between a sharp tungsten tip and elements of nanostructured materials. Using the advantages of field enhancement at sharp ends of nanostructured materials, the discharge voltage is reduced to 25-30 V, depending upon the materials density. This method causes largely non-oxidative sequential decomposition of nanostructure elements neighboring the tungsten tip. The main decomposition mechanism is thermal dissociation facilitated by Joule heating and electrostatic removal of debris. The non-contact-based patterning of nanomaterials can be as fast as 10 cm s-1. The resulting precisely patterned structures (<200 nm) are largely free of foreign contaminants, thermal impact and sub-surface structural changes.

Torsional refrigeration by twisted, coiled, and supercoiled fibers.

Higher-efficiency, lower-cost refrigeration is needed for both large- and small-scale cooling. Refrigerators using entropy changes during cycles of stretching or hydrostatic compression of a solid are possible alternatives to the vapor-compression fridges found in homes. We show that high cooling results from twist changes for twisted, coiled, or supercoiled fibers, including those of natural rubber, nickel titanium, and polyethylene fishing line. Using opposite chiralities of twist and coiling produces supercoiled natural rubber fibers and coiled fishing line fibers that cool when stretched. A demonstrated twist-based device for cooling flowing water provides high cooling energy and device efficiency. Mechanical calculations describe the axial and spring-index dependencies of twist-enhanced cooling and its origin in a phase transformation for polyethylene fibers.

New mechanism of plasmons specific for spin-polarized nanoparticles.

Here it is experimentally shown that Co nanoparticles with a single-domain crystal structure support a plasmon resonance at approximately 280 nm with better quality than gold nanoparticle resonance in the visible. Magnetic nature of the nanoparticles suggests a new type of these plasmons. The exchange interaction of electrons splits the energy bands between spin-up electrons and spin-down electrons. It makes it possible for coexistence of two independent channels of conductivity as well as two independent plasmons in the same nanoparticle with very different electron relaxation. Indeed, the density of empty states in a partially populated d-band is high, resulting in a large relaxation rate of the spin-down conduction electrons and consequently in low quality of the plasmon resonance. In contrast, the majority electrons with a completely filled d-band do not provide final states for the scattering processes of the conduction spin-up electrons, therefore supporting a high quality plasmon resonance. The scattering without spin flip is required to keep these two plasmons independent.

Sequentially bridged graphene sheets with high strength, toughness, and electrical conductivity.

We here show that infiltrated bridging agents can convert inexpensively fabricated graphene platelet sheets into high-performance materials, thereby avoiding the need for a polymer matrix. Two types of bridging agents were investigated for interconnecting graphene sheets, which attach to sheets by either π-π bonding or covalent bonding. When applied alone, the π-π bonding agent is most effective. However, successive application of the optimized ratio of π-π bonding and covalent bonding agents provides graphene sheets with the highest strength, toughness, fatigue resistance, electrical conductivity, electromagnetic interference shielding efficiency, and resistance to ultrasonic dissolution. Raman spectroscopy measurements of stress transfer to graphene platelets allow us to decipher the mechanisms of property improvement. In addition, the degree of orientation of graphene platelets increases with increasing effectiveness of the bonding agents, and the interlayer spacing increases. Compared with other materials that are strong in all directions within a sheet, the realized tensile strength (945 MPa) of the resin-free graphene platelet sheets was higher than for carbon nanotube or graphene platelet composites, and comparable to that of commercially available carbon fiber composites. The toughness of these composites, containing the combination of π-π bonding and covalent bonding, was much higher than for these other materials having high strengths for all in-plane directions, thereby opening the path to materials design of layered nanocomposites using multiple types of quantitatively engineered chemical bonds between nanoscale building blocks.

Thermoacoustic sound projector: exceeding the fundamental efficiency of carbon nanotubes.

The combination of smooth, continuous sound spectra produced by a sound source having no vibrating parts, a nanoscale thickness of a flexible active layer and the feasibility of creating large, conformal projectors provoke interest in thermoacoustic phenomena. However, at low frequencies, the sound pressure level (SPL) and the sound generation efficiency of an open carbon nanotube sheet (CNTS) is low. In addition, the nanoscale thickness of fragile heating elements, their high sensitivity to the environment and the high surface temperatures practical for thermoacoustic sound generation necessitate protective encapsulation of a freestanding CNTS in inert gases. Encapsulation provides the desired increase of sound pressure towards low frequencies. However, the protective enclosure restricts heat dissipation from the resistively heated CNTS and the interior of the encapsulated device. Here, the heat dissipation issue is addressed by short pulse excitations of the CNTS. An overall increase of energy conversion efficiency by more than four orders (from 10-5 to 0.1) and the SPL of 120 dB re 20 µPa @ 1 m in air and 170 dB re 1 µPa @ 1 m in water were demonstrated. The short pulse excitation provides a stable linear increase of output sound pressure with substantially increased input power density (>2.5 W cm-2). We provide an extensive experimental study of pulse excitations in different thermodynamic regimes for freestanding CNTSs with varying thermal inertias (single-walled and multiwalled with varying diameters and numbers of superimposed sheet layers) in vacuum and in air. The acoustical and geometrical parameters providing further enhancement of energy conversion efficiency are discussed.

Carbonized Electrospun Nanofiber Sheets for Thermophones.

Thermoacoustic performance of thin freestanding sheets of carbonized poly(acrylonitrile) and polybenzimidazole nanofibers are studied as promising candidates for thermophones. We analyze thermodynamic properties of sheets using transport parameters of single nanofibers and their aligned and randomly electrospun thin film assemblies. The electrical and thermal conductivities, thermal diffusivity, heat capacity, and infrared blackbody radiation are investigated to extract the heat exchange coefficient and enhance the energy conversion efficiency. Spectral and power dependencies of sound pressure in air are compared with carbon nanotube sheets and theoretical prediction. Despite lower thermoacoustic performance compared to that of CNT sheets, the mechanical strength and cost-effective production technology of thermophones make them very attractive for large-size sound projectors. The advantages of carbonized electrospun polymer nanofiber sheets are in the low frequency domain (<1000 Hz), where the large thermal diffusion length diminishes the thermal inertia of thick (∼200 nm) nonbundled fibers and the high intrinsic thermal conductivity of fibers enhances the heat exchange coefficient. Applications of thermoacoustic projectors for loudspeakers, high power SONAR arrays, and sound cancellation are discussed.

New twist on artificial muscles.

Lightweight artificial muscle fibers that can match the large tensile stroke of natural muscles have been elusive. In particular, low stroke, limited cycle life, and inefficient energy conversion have combined with high cost and hysteretic performance to restrict practical use. In recent years, a new class of artificial muscles, based on highly twisted fibers, has emerged that can deliver more than 2,000 J/kg of specific work during muscle contraction, compared with just 40 J/kg for natural muscle. Thermally actuated muscles made from ordinary polymer fibers can deliver long-life, hysteresis-free tensile strokes of more than 30% and torsional actuation capable of spinning a paddle at speeds of more than 100,000 rpm. In this perspective, we explore the mechanisms and potential applications of present twisted fiber muscles and the future opportunities and challenges for developing twisted muscles having improved cycle rates, efficiencies, and functionality. We also demonstrate artificial muscle sewing threads and textiles and coiled structures that exhibit nearly unlimited actuation strokes. In addition to robotics and prosthetics, future applications include smart textiles that change breathability in response to temperature and moisture and window shutters that automatically open and close to conserve energy.

Strong, Twist-Stable Carbon Nanotube Yarns and Muscles by Tension Annealing at Extreme Temperatures.

A high-speed incandescent tension annealing process (ITAP) is used to increase the modulus and strength of twist-spun carbon nanotube yarns by up to 12-fold and 2.6-fold, respectively, provide remarkable resistance to oxidation and powerful protonating acids, and freeze yarn untwist. This twist stability enables torsional artificial-muscle motors having improved performance and minimizes problematic untwist during weaving nanotube yarns.

Woven-Yarn Thermoelectric Textiles.

The fabrication and characterization of highly flexible textiles are reported. These textiles can harvest thermal energy from temperature gradients in the desirable through-thickness direction. The tiger yarns containing n- and p-type segments are woven to provide textiles containing n-p junctions. A high power output of up to 8.6 W m(-2) is obtained for a temperature difference of 200 °C.

Chemoradiotherapeutic Magnetic Nanoparticles for Targeted Treatment of Nonsmall Cell Lung Cancer.

Lung cancer is the leading cause of cancer-related death in the United States and approximately 85% of all lung cancers are classified as nonsmall cell (NSCLC). We here use an innovative approach that may ultimately allow for the clinician to target tumors and aggressively reduce tumor burden in patients with NSCLC. In this study, a platinum (Pt)-based chemotherapeutic (cisplatin, carboplatin, or oxaliplatin) and holmium-165 (Ho), which can be neutron-activated to produce the holmium-166 radionuclide, have been incorporated together in a garnet magnetic nanoparticle (HoIG-Pt) for selective delivery to tumors using an external magnet. The synthesized magnetic HoIG nanoparticles were characterized using PXRD, TEM, ICP-MS, and neutron-activation. Platinum(II) drugs were incorporated onto HoIG, and these were characterized using FTIR, EDX, ICP-MS, and zeta potential measurements, and in vitro and in vivo studies were performed using a HoIG-platinum system. Results indicate that neutron-activated (166)HoIG-cisplatin is more toxic toward NSCLC A549 cells than is blank (166)HoIG and free cisplatin, and that when an external magnetic field is applied in vivo, higher tumor to liver ratios of Ho are observed than when no magnet is applied, suggesting that magnetic targeting is achieved using this system. Furthermore, an efficacy study demonstrated the inhibition of tumor growth by chemoradiotherapeutic magnetic nanoparticles, compared to no treatment controls.

Optical, electrical, and electromechanical properties of hybrid graphene/carbon nanotube films.

By combining a graphene layer and aligned multiwalled carbon nanotube (MWNT) sheets in two different configurations, i) graphene on the top of MWNTs and ii) MWNTs on the top of the graphene, it is demonstrated that optical, electrical, and electromechanical properties of the resulting hybrid films depend on configurations.

Alternative nanostructures for thermophones.

Thermophones are highly promising for applications such as high-power SONAR arrays, flexible loudspeakers, and noise cancellation devices. So far, freestanding carbon nanotube aerogel sheets provide the most attractive performance as a thermoacoustic heat source. However, the limited accessibility of large-size freestanding carbon nanotube aerogel sheets and other even more exotic materials recently investigated hampers the field. We describe alternative materials for a thermoacoustic heat source with high-energy conversion efficiency, additional functionalities, environmentally friendly, and cost-effective production technologies. We discuss the thermoacoustic performance of alternative nanostructured materials and compare their spectral and power dependencies of sound pressure in air. We demonstrate that the heat capacity of aerogel-like nanostructures can be extracted by a thorough analysis of the sound pressure spectra. The study presented here focuses on engineering thermal gradients in the vicinity of nanostructures and subsequent heat dissipation processes from the interior of encapsulated thermoacoustic projectors. Applications of thermoacoustic projectors for high-power SONAR arrays, sound cancellation, and optimal thermal design, regarding enhanced energy conversion efficiency, are discussed.

Three-dimensionally bonded spongy graphene material with super compressive elasticity and near-zero Poisson's ratio.

It is a challenge to fabricate graphene bulk materials with properties arising from the nature of individual graphene sheets, and which assemble into monolithic three-dimensional structures. Here we report the scalable self-assembly of randomly oriented graphene sheets into additive-free, essentially homogenous graphene sponge materials that provide a combination of both cork-like and rubber-like properties. These graphene sponges, with densities similar to air, display Poisson's ratios in all directions that are near-zero and largely strain-independent during reversible compression to giant strains. And at the same time, they function as enthalpic rubbers, which can recover up to 98% compression in air and 90% in liquids, and operate between -196 and 900 °C. Furthermore, these sponges provide reversible liquid absorption for hundreds of cycles and then discharge it within seconds, while still providing an effective near-zero Poisson's ratio.

Thermal management of thermoacoustic sound projectors using a free-standing carbon nanotube aerogel sheet as a heat source.

Carbon nanotube (CNT) aerogel sheets produce smooth-spectra sound over a wide frequency range (1-10(5) Hz) by means of thermoacoustic (TA) sound generation. Protective encapsulation of CNT sheets in inert gases between rigid vibrating plates provides resonant features for the TA sound projector and attractive performance at needed low frequencies. Energy conversion efficiencies in air of 2% and 10% underwater, which can be enhanced by further increasing the modulation temperature. Using a developed method for accurate temperature measurements for the thin aerogel CNT sheets, heat dissipation processes, failure mechanisms, and associated power densities are investigated for encapsulated multilayered CNT TA heaters and related to the thermal diffusivity distance when sheet layers are separated. Resulting thermal management methods for high applied power are discussed and deployed to construct efficient and tunable underwater sound projector for operation at relatively low frequencies, 10 Hz-10 kHz. The optimal design of these TA projectors for high-power SONAR arrays is discussed.