Biomechanical behavior of different designs of hybrid abutment-restoration on the posterior crown: a finite element analysis.

This study aimed to evaluate the influence of material and crown design on the biomechanical behavior of implant-supported crowns with hybrid abutment (HA) through three-dimensional (3D) finite element analysis. The study factors were the type of material used as the mesostructure or crown (zirconia, lithium disilicate, and hybrid ceramic) and the crown design cemented to the titanium base (mesostructure cemented to the titanium base and a crown cemented on it (HaC); hybrid crown-abutment, the abutment and crown are manufactured as a single piece and cemented to the titanium base (HC); monolithic crown cemented on the titanium base and screwed to the implant (CS); and monolithic crown cemented on the titanium base (CC). Four 3D models were constructed using an implant with an internal connection, and an oblique load of 130 N was applied at 45° to the long axis of the implant. The models were evaluated using the von Mises stress for crown, abutment, screw, and implant and maximum principal stress for bone tissues. The lowest stresses occurred in the groups with a lower elastic modulus material, mainly hybrid ceramics, considered a material with greater resilience. The cemented crown group presented the lowest stress values. The stresses were concentrated in the cervical region of the crown at the titanium crown/base interface. Mesostructures made of materials with a higher elastic modulus exhibited a higher concentration of stress. The presence of a screw hole increased the stress concentration in the ceramic crown. Cemented ceramic crowns exhibited better biomechanical behavior than screw-retained crowns.

Influence of Chitosan 0.2% in Various Final Cleaning Methods on the Bond Strength of Fiberglass Post to Intrarradicular Dentin.

The purpose of this study was to analyze the influence of Chitosan 0.2% in various final cleaning methods on the bond strength of fiberglass post (FP) to intrarradicular dentin. Ninety bovine incisors were sectioned to obtain root remnants measuring 18 mm in length. The roots were divided: G1: EDTA 17%; G2: EDTA 17% + PUI; G3: EDTA 17% + EA; G4: EDTA 17% + XPF; G5: Chitosan 2%; G6: Chitosan 2% + PUI; G7: Chitosan 2% + EA; G8: Chitosan 2% +XPF. After carrying out the cleaning methods, the posts were installed, and the root was cleaved to generate two disks from each root third. Bond strength values (MPa) obtained from the micro push-out test data were assessed by using Kruskal-Wallis and Dwass-Steel-Critchlow-Fligner tests for multiple comparisons (α = 5%). Differences were observed in the cervical third between G1 and G8 (p = 0.038), G4 and G8 (p = 0.003), G6 and G8 (p = 0.049), and Control and G8 (p = 0.019). The final cleaning method influenced the adhesion strength of cemented FP to intrarradicular dentin. Chitosan 0.2% + XPF positively influenced adhesion strength, with the highest values in the cervical third.

Socket shield technique: Stress distribution analysis.

Background: To analyze through finite element analysis the stress distribution in peri-implant bone tissues, implants, and prosthetic components induced by the socket shield (SS) technique in comparison to other techniques used to treat tooth loss. Materials and Methods: A three-dimensional model of a superior central incisor crown supported by implant was modeled and three different placement conditions were simulated: SS - 2.0-mm-thick root dentin fragment positioned between the alveolar buccal wall and implant; heterologous bone graft (HBG) - bovine bone graft positioned the alveolar buccal wall and implant; and control (C) - implant fully placed in bone tissue of a healed alveolus. The model was restricted at the lateral surfaces of the bone tissue and the following loads were simulated: Both oblique (45°) loads of 100 N on the lingual surface of the crown (maximal habitual intercuspation) and 25.5 N on the incisal edge of the crown (tooth contact during mandibular protrusion) were simultaneously applied. Tensile stress, shear stress, compression, and displacement were analyzed in the cortical bone, trabecular bone, dentin root fragment, and bone graft; while equivalent von Mises stresses were quantified in the implant and prosthetic components. Results: Stress values of SS and HBG in the bone tissues were higher than C, while slight differences within models were observed for dentin root fragment, bone graft, implant, and prosthetic components. Conclusions: The SS technique presented the highest stress concentration in the peri-implant tissues.

Preheated restorative composite resin for luting ceramic laminate veneers: An optimized technique report.

Resin cements are traditionally used to lute ceramic laminate veneers due to their lower viscosity, which facilitates a fast restoration seating. However, resin cements have lower mechanical properties compared to restorative composite resins. Thus, restorative composite resin is an alternative luting agent with lower marginal degradation as a potential advantage for clinical longevity. This article presents an application of preheated restorative composite resin for adhesive luting of laminate veneers with a predictable clinical technique for seating and marginal quality. By addressing important factors that influence film thickness, the predictable presented workflow should overcome this major concern when luting with restorative composite resin, therefore enabling the benefits of using a restorative material with better mechanical properties without the drawback of higher film thickness. Considering the clinical evidence that the adhesive interface between the dental substrate and restoration is the weak link of adhesive indirect restorations, bonding the restoration with preheated restorative composite resins (PRCR) may provide an interface filled with a restorative resin material, presenting optimized mechanical properties. Key words:Resin cements, ceramic laminate veneers.

Effect of thickness and CAD-CAM material on fatigue resistance of endodontically treated molars restored with occlusal veneers.

PURPOSE: To evaluate the influence of the thickness and type of computer-aided design and computer-aided manufacturing (CAD-CAM) material on the fatigue resistance and failure mode of endodontically treated teeth (ETT) restored with occlusal veneers (OV). MATERIALS AND METHODS: Seventy-five (N = 75) ETT were restored with Herculite XRV in the endodontic access. Five experimental groups (n = 15) were tested. Four groups had two different thicknesses (0.6-0.7 mm or 1.4-1.6 mm) and two different CAD-CAM materials: zirconia-reinforced lithium-silicate (LS/Celtra Duo) and composite resin (RC/Cerasmart). The fifth group (control) did not have occlusal veneers. All the specimens were subjected to accelerated fatigue (5 Hz frequency) with an occlusal load increasing up to 1800 N and 131,000 cycles. The number of cycles was recorded when the machine stopped or at the completion of the test. Fatigue resistance was analyzed using the Kaplan-Meier survival test (95% significance level, log-rank post hoc pairwise comparisons). The samples were categorized according to failure mode. The CAD-CAM materials were examined through scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDS). RESULTS: No differences were found between the thicknesses, regardless of the type of the CAD-CAM material. The thick LS OV outperformed the RC and control groups. The thin RC OV and control groups showed a higher percentage of repairable and possibly repairable failures than the other groups. LS was more homogeneous under SEM, and the EDS analysis detected Si and Zr, but not Li. CONCLUSIONS: A larger thickness did not improve the resistance of the CAD-CAM materials. Thick LS showed a higher cumulative survival rate to fatigue than the RC and control groups. The direct composite alone (control) survived similarly to the experimental groups, except for the thick LS.

Biomechanical behavior of different designs of hybrid abutment-restoration on the posterior crown: a finite element analysis

Abstract This study aimed to evaluate the influence of material and crown design on the biomechanical behavior of implant-supported crowns with hybrid abutment (HA) through three-dimensional (3D) finite element analysis. The study factors were the type of material used as the mesostructure or crown (zirconia, lithium disilicate, and hybrid ceramic) and the crown design cemented to the titanium base (mesostructure cemented to the titanium base and a crown cemented on it (HaC); hybrid crown-abutment, the abutment and crown are manufactured as a single piece and cemented to the titanium base (HC); monolithic crown cemented on the titanium base and screwed to the implant (CS); and monolithic crown cemented on the titanium base (CC). Four 3D models were constructed using an implant with an internal connection, and an oblique load of 130 N was applied at 45° to the long axis of the implant. The models were evaluated using the von Mises stress for crown, abutment, screw, and implant and maximum principal stress for bone tissues. The lowest stresses occurred in the groups with a lower elastic modulus material, mainly hybrid ceramics, considered a material with greater resilience. The cemented crown group presented the lowest stress values. The stresses were concentrated in the cervical region of the crown at the titanium crown/base interface. Mesostructures made of materials with a higher elastic modulus exhibited a higher concentration of stress. The presence of a screw hole increased the stress concentration in the ceramic crown. Cemented ceramic crowns exhibited better biomechanical behavior than screw-retained crowns.

Resumo O estudo teve como objetivo avaliar a influência do material e do desenho da coroa no comportamento biomecânico de coroas implanto-suportadas com pilar híbrido (AH) por meio da análise tridimensional (3D) de elementos finitos. Os fatores de estudo foram o tipo de material do HA ou coroa (zircônia, dissilicato de lítio e cerâmica híbrida) e o desenho da coroa sobre a base de titânio (mesoestrutura cimentada à base de titânio e coroa total cimentada em cerâmica; pilar e coroa fabricados em peça única cimentada à base de titânio; coroa monolítica cimentada sobre a base de titânio e aparafusada ao implante; e coroa monolítica cimentada à base de titânio). Quatro modelos 3D foram construídos e uma carga oblíqua de 130 N foi aplicada a 45° em relação ao longo eixo do dente. Os modelos foram avaliados utilizando a tensão de von Mises para a coroa, pilar, parafuso, implante e tensão principal máxima (tensão de tração) para o tecido ósseo. As menores tensões ocorreram nos grupos que apresentaram um material com menor módulo de elasticidade, principalmente a cerâmica híbrida, considerada um material com maior resiliência. Com relação às diferentes configurações, o modelo com coroa cimentada apresentou os menores valores de tensão. As tensões foram concentradas na região cervical da coroa na interface entre coroa e base de titânio. Mesoestruturas feitas de materiais com maior módulo de elasticidade exibiram maior concentração de tensões. A presença de um orifício para parafuso aumentou a concentração de tensão na coroa de cerâmica. As coroas cerâmicas cimentadas exibiram melhor comportamento biomecânico do que as coroas parafusadas.

Fatigue and failure analysis of restored endodontically treated maxillary incisors without a dowel or ferrule.

STATEMENT OF PROBLEM: Information on the survival and mode of failure of endodontically treated incisors without a ferrule and restored without dowels is lacking. PURPOSE: The purpose of this in vitro study was to compare the survival and failure mode of endodontically treated incisors without a ferrule and restored with bonded ceramic crowns and various composite resin foundation restorations without dowels with a control group with fiber dowels. MATERIAL AND METHODS: Forty-five decoronated endodontically treated bovine incisors without ferrule were divided into 3 experimental groups and restored with different adhesive foundation restorations without dowel: nanohybrid composite resin (Nd), bulk-fill composite resin foundation restoration (NdB), and fiber-reinforced bulk-fill composite resin (NdFR). A control group with conventional foundation restorations (glass-fiber dowel with nanohybrid composite resin foundation restoration without ferrule) (D) was included for comparison. All teeth were prepared to receive bonded lithium disilicate ceramic crowns luted with dual-polymerizing composite resin cement and were subjected to accelerated fatigue testing. Cyclic isometric loading was applied to the incisal edge at an angle of 30 degrees and a frequency of 5 Hz, beginning with a load of 100 N (5000 cycles). A 100-N load increase was applied each 15 000 cycles. Specimens were loaded until failure or to a maximum for cycles endured of 1000 N (140 000 cycles). Groups were compared by using the Kaplan-Meier survival analysis (log rank test at α=.05 and pairwise post hoc comparisons) and life table analysis for load-at-failure (followed by Wilcoxon pairwise comparison α=.05). RESULTS: All the specimens failed before 140 000 load cycles. Even though no statistically significant differences were found between the experimental groups without dowel (P>.127), the fiber-reinforced foundation restoration yielded the highest mean ±standard deviation cycles to failure (46 023 ±4326) compared with Nd (38 899 ±2975) and NdB (39 751 ±2998). NdFR, however, outperformed the foundation restoration with glass-fiber dowel (35 026 ±2687) (P<.05). Most failure in groups without dowel were restorable, while 100% of catastrophic failure (unrestorable) were found in the group with dowels. CONCLUSIONS: Based on the present in vitro study, dowels did not improve the performance of the adhesive restoration of endodontically treated incisors without a ferrule. The use of a short fiber-reinforced composite resin foundation restoration without a dowel was able to not only improve the resistance of the restorations compared with adhesive foundation restorations with dowels but also minimize catastrophic failures.

A three-dimensional finite element analysis of permanent maxillary central incisors in different stages of root development and trauma settings.

BACKGROUND AND OBJECTIVES: Differences in dental maturation may affect the prognosis and clinical management of traumatized teeth. However, evaluation of the outcomes of dental trauma to the tooth and support structures in an in vivo model involves major methodological and ethical implications. Thus, the aim of the present study was to perform a three-dimensional finite element analysis of permanent maxillary central incisors in different stages of root development under different trauma settings. METHODS: The study factors included two trauma conditions (B, buccal; I, incisal) on upper permanent central incisors showing three different stages of root development (CR, complete rhizogenesis; IRA; incomplete rhizogenesis in the apical third of the root; and IRM, incomplete rhizogenesis in the middle third of the root) to yield six models. The complete rhizogenesis model was obtained with a cone-beam computed tomography examination of an extracted tooth. The two incomplete rhizogenesis models were modeled on the basis of similar examinations of patients. Trauma was simulated by applying a 300 N static surface to surface load on the incisal edge or perpendicular to the buccal surface of the tooth. The displacement and equivalent von Mises (σvM) stress values were obtained for alveolar bone, periodontal ligament, apical papilla, and dentin for the quantitative analysis. A σvM color-coded scale was used for qualitative analysis. RESULTS: The force direction had a greater influence on the stress than the root-formation stage. Buccal forces resulted in higher stress concentration in the bone and periodontal ligament, especially in B-CR. Lower stress was found on the periodontal ligament as the root formation progressed (decrease of 8% from B-IRA to B-CR and 11% from B-IRM to B-CR). The incomplete rhizogenesis models showed higher σvM stress peak values in dentin in comparison with complete rhizogenesis (increase of 52% from B-CR to B-IRA and 56% from B-CR to B-IRM). CONCLUSIONS: Buccal forces yielded greater stress values regardless of the stage of rhizogenesis. Teeth with fully formed roots showed a higher stress concentration in the alveolar bone and periodontal ligament in comparison with immature teeth, with the latter presenting high stresses in the tooth crown.

Different Treatment Modalities Using Dental Implants in the Posterior Maxilla: A Finite Element Analysis.

The objective of this study was to compare the biomechanical behavior of peri-implant bone tissue and prosthetic components in two modalities of treatment for posterior region of the maxilla, using short implants or standard-length implants associated with bone graft in the maxillary sinus. Four 3D models of a crown supported by an implant fixed in the posterior maxilla were constructed. The type of implant: short implant (S) or standard-length implant with the presence of sinus graft (L) and type of crown retention: cemented (C) or screwed (S) were the study factors. The models were divided into SC- cemented crown on a short implant; SS- screwed crown on the short implant; LC- cemented crown on a standard-length implant after bone graft in the maxillary sinus and LS- crown screwed on a standard-length implant after bone graft in the maxillary sinus. An axial occlusal loading of 300 N was applied, divided into five points (60N each) corresponding to occlusal contact. The following analysis criteria were observed: Shear Stress, Maximum and Minimum Main Stress for bone tissue and von Mises Stress for the implant and prosthetic components. The use of standard-length implants reduced the shear stress in the cortical bone by 35.75% and the medullary bone by 51% when compared to short implants. The length of the implant did not affect the stress concentration in the crown, and the cement layer acted by reducing the stresses in the ceramic veneer and framework by 42%. Standard-implants associated with cemented crowns showed better biomechanical behavior.

Different treatment modalities using dental implants in the posterior maxilla: a finite element analysis

Abstract The objective of this study was to compare the biomechanical behavior of peri-implant bone tissue and prosthetic components in two modalities of treatment for posterior region of the maxilla, using short implants or standard-length implants associated with bone graft in the maxillary sinus. Four 3D models of a crown supported by an implant fixed in the posterior maxilla were constructed. The type of implant: short implant (S) or standard-length implant with the presence of sinus graft (L) and type of crown retention: cemented (C) or screwed (S) were the study factors. The models were divided into SC- cemented crown on a short implant; SS- screwed crown on the short implant; LC- cemented crown on a standard-length implant after bone graft in the maxillary sinus and LS- crown screwed on a standard-length implant after bone graft in the maxillary sinus. An axial occlusal loading of 300 N was applied, divided into five points (60N each) corresponding to occlusal contact. The following analysis criteria were observed: Shear Stress, Maximum and Minimum Main Stress for bone tissue and von Mises Stress for the implant and prosthetic components. The use of standard-length implants reduced the shear stress in the cortical bone by 35.75% and the medullary bone by 51% when compared to short implants. The length of the implant did not affect the stress concentration in the crown, and the cement layer acted by reducing the stresses in the ceramic veneer and framework by 42%. Standard-implants associated with cemented crowns showed better biomechanical behavior.

Resumo O objetivo do estudo foi avaliar o comportamento biomecânico do tecido ósseo peri-implantar e dos componentes protéticos em duas modalidades de tratamento para região posterior da maxila, utilizando implantes curtos ou implantes de comprimento padrão associados a enxerto ósseo em seio maxilar. Foram construídos quatro modelos 3D de uma coroa suportada por um implante osseointegrado na região posterior da maxila. O tipo de implante: implante curto (S) ou implante de comprimento padrão com presença de enxerto sinusal (L) e tipo de retenção da restauração: cimentada (C) ou parafusada (S) foram os fatores de estudo. Foi aplicada uma força oclusal de 300N, dividida em cinco pontos (60 N cada) correspondentes ao contato oclusal de um primeiro molar superior. Foram observados os seguintes critérios de análise: tensão de cisalhamento, tensão principal máxima e mínima para o tecido ósseo e tensão de Von Mises para o implante e componentes protéticos. O uso de implantes de comprimento padrão reduziu a tensão de cisalhamento no osso cortical em 35,75% e no osso medular em 51% quando comparado aos implantes curtos. O comprimento do implante não afetou a concentração de tensão na restauração. A camada de cimento atuou reduzindo as tensões na cerâmica de cobertura e infraestrutura de cerâmica em 42%. Os implantes de tamanho padrão associados às coroas cimentadas apresentaram o melhor comportamento biomecânico.

Significance of immediate dentin sealing and flowable resin coating reinforcement for unfilled/lightly filled adhesive systems.

BACKGROUND: Immediate dentin sealing implies applying an adhesive system to dentin directly after tooth preparation, before impression. The technique is universal (inlays, onlays, veneers, crowns) and well documented clinically and experimentally. Different types of dentin bonding agents (DBAs) are available on the market. Major differences lie in the thickness of the hybrid layer and overlaying adhesive resin (filled vs. unfilled/lightly filled adhesives). OBJECTIVE: The objective of this work is to provide precise clinical instructions and present new experimental data about the bond strength of five DBAs (Optibond FL, Scotchbond MP, Single Bond Plus, Clearfil SE Bond, and Scotchbond Universal) used conventionally (dentin sealed at the time of restoration delivery) or with immediate dentin sealing, as well as with an additional flowable resin coating. METHODS: Seventy-five human molars were selected, restored/tested according the microtensile bond strength method. Fifteen groups (n=5) were obtained from the combination of the five DBAs and three application modes: delayed dentin sealing, immediate dentin sealing and immediate dentin sealing with flowable resin coating. RESULTS: It appears that immediate dentin sealing was confirmed to significantly improve the bond strength of all tested adhesives. The use of a flowable resin coating reinforcement after immediate dentin sealing increased the microtensile bond strength of all unfilled/lightly filled adhesives (from 233% of increase for ScotchBond MP, up to 560% for Clearfil SE Bond) and maintained the performance of the 3-step golden standard adhesive. Optibond FL used with (52.51 MPa) or without (54.75 MPa) additional flowable resin coating and Clearfil SE Bond (45.64 MPa) used with flowable resin coating provided the best results. CLINICAL SIGNIFICANCE: The original immediate dentin sealing (IDS) technique implies the use of a filled DBA. With unfilled/lightly filled adhesives, it is suggested to reinforce IDS with an additional flowable resin coating. This seems especially paramount to the performance of simplified adhesive systems to protect the thin bonding interface from oxygen inhibition and preserve IDS layer during predelivery cleaning of the preparation. The clinical reinforcement of unfilled/lightly filled IDS with flowable resin composite is encouraged for more predictable bonding.

3D finite element model based on CT images of tooth: a simplified method of modeling

Aim: This study aimed the description of a protocol to acquire a 3D finite element (FE) model of a human maxillary central incisor tooth restored with ceramic crowns with enhanced geometric detail through an easy-to-use and low-cost concept and validate it through finite element analysis (FEA). Methods: A human maxillary central incisor was digitalized using a Cone Beam Computer Tomography (CBCT) scanner. The resulted tooth CBCT DICOM files were imported into a free medical imaging software (Invesalius) for 3D surface/geometric reconstruction in stereolithographic file format (STL). The STL file was exported to a computer-aided-design (CAD) software (SolidWorks), converted into a 3D solid model and edited to simulate different materials for full crown restorations. The obtained model was exported into a FEA software to evaluate the influence of different core materials (zirconia - Zr, lithium disilicate - Ds or palladium/silver - Ps) on the mechanical behavior of the restorations under a 100 N applied to the palatal surface at 135 degrees to the long axis of the tooth, followed by a load of 25.5 N perpendicular to the incisal edge of the crown. The quantitative and qualitative analysis of maximum principal stress (ceramic veneer) and maximum principal strain (core) were obtained. Results: The Zr model presented lower stress and strain concentration in the ceramic veneer and core than Ds and Ps models. For all models, the stresses were concentrated in the external surface of the veneering ceramic and strains in the internal surface of core, both near to the loading area. Conclusion: The described procedure is a quick, inexpensive and feasible protocol to obtain a highly detailed 3D FE model, and thus could be considered for future 3D FE analysis. The results of numerical simulation confirm that stiffer core materials result in a reduced stress concentration in ceramic veneer

Reabilitação estética anterior com facetas e coroas cerâmicas: relato de caso clínico / Anterior esthetic rehabilitation with porcelain veneers and ceramic crowns: a case report

Objetivo: Este trabalho tem como objetivo apresentar um caso clínico de reabilitação estética anterior (centrais e laterais anterossuperiores) associando facetas e coroas cerâmicas cimentadas com diferentes técnicas (cimento resinoso e resina composta aquecida) com a finalidade de reproduzir as características dos dentes naturais. Material e Métodos: Paciente A.M.A., gênero feminino, 47 anos, compareceu à clínica odontológica da Faculdade de Odontologia da Universidade Federal de Goiás (UFG), relatando insatisfação com a estética do seu sorriso, diferenças no formato e cor de seus dentes. Ao exame clínico intrabucal verificou-se uma coroa total provisória do dente 22, e o mau posicionamento do dente 12 em relação aos adjacentes. Foi indicada cirurgia periodontal para aumento de coroa clínica, clareamento dental, duas facetas cerâmicas nos incisivos centrais e duas coroas cerâmicas nos incisivos laterais superiores. Após a cirurgia periodontal e clareamento, foi realizado o refinamento dos preparos para coroa total e preparos para faceta cerâmica. O material de escolha para as restaurações foi o dissilicato de lítio devido sua grande capacidade de mimetizar o dente natural. As coroas foram cimentadas com isolamento relativo do campo operatório e cimento resinoso dual. As facetas foram cimentadas com isolamento absoluto e resina composta aquecida. Resultados: Após 15 dias da cimentação a paciente retornou à clínica onde se observou saúde periodontal e perfeita adaptação das restaurações indiretas. Conclusão: Obteve-se excelente resultado estético associando diferentes tipos de restaurações e técnicas de cimentação adesiva e a paciente se mostrou confortável com as diferentes abordagens e satisfeita com o resultado estético do tratamento.

Objective: This study aims to present a clinical case of anterior aesthetic rehabilitation (central and anterior superior sides), combining cemented ceramic veneers and crowns with different techniques (resin cement and heated composite resin) with the use of chemical substances as used substances. Material and Methods: Patient A.M.A., female, 47 years old, compared to the dental clinic of the Faculty of Dentistry of the Federal University of Goiás (UFG), relating dissatisfaction with the aesthetics of his smile, differences in the shape and color of his patients. On intraoral clinical examination, a provisional total crown of tooth 22 was found, and tooth 12 was poorly positioned in relation to adjacent teeth. Periodontal surgery was indicated to increase the clinical crown, tooth whitening, two ceramic veneers on the central incisors and two ceramic crowns on the upper lateral incisors. After periodontal surgery and whitening, the preparations for the full crown and preparations for the ceramic veneer were refined. The material of choice for restorations was dissolved on the site due to its great ability to mimic the natural tooth. As crowns, they were cemented with isolation relative to the operative field and double resin cement. The veneers were cemented with absolute insulation and heated composite resin. Results: After 15 days of cementation, the patient returned to the clinic where he recovered from periodontal health and perfect adaptation of the indirect restorations. Conclusion: You get an excellent aesthetic result by associating different types of restorations and adhesive cementation techniques and a patient is comfortable with different approaches and satisfaction with the aesthetic result of the treatment.

Current options concerning the endodontically-treated teeth restoration with the adhesive approach.

Adhesive procedures have changed the way to restore endodontically treated teeth (ETT). It started with the shift from cast post-and-core to fiber post. The original focus on strength also shifted towards failure modes, revealing that catastrophic failures are still a concern when restoring endodontically-treated teeth even with fiber posts. As an alternative, postless approaches have been proposed in order to improve the chances of repair. The goal of this critical review is to present a survey of the current knowledge on adhesive approaches to restore endodontically treated teeth with and without extensive coronal tissue loss. The preservation of tooth structure of endodontically treated teeth is paramount. Partial versus full coverage of ETT, the role of the ferrule, the post type effect on catastrophic failures and postless alternatives as endocrowns and postless build-ups are reviewed. There is a consensus that the remaining tooth structure plays an important role in ETT survival, although the current literature still is contradictory on the influence of post type on root fractures as well as the benefits of avoiding a post or partially restoring a tooth. More clinical studies should be carried out with the modern postless adhesive alternatives to conventional approaches.

Case Report: a 5-Year Follow-up of Proximal Caries Lesion Diagnosis / Diagnóstico de Lesões Cariosas Proximais - Relato de Caso: 5 Anos de Acompanhamento

This clinical case was aimed at reporting and discussing diagnostic methods for early detection and preventive treatment of proximal carious lesions. The patient presented to the dental clinic seeking treatment of a problem she reported as being "dental caries". The patient's orthodontist diagnosed dental caries, by means of radiographic exam. There was no evidence of any proximal carious lesion in the intraoral examination. The bitewing radiographs presented a radiolucent area limited to enamel in the mesial of maxillary left-second-bicuspid. For the purpose of confirming the intraoral diagnosis, an immediate tooth separation was performed. The immediate separation was unable to provide sufficient access; thus, the slow separation approach was performed. After 24-hours, tooth separation of 1mm was obtained, providing enough access for clinical examination. The proximal areas were evaluated by transillumination and impression taking. During the visual inspection, an area of enamel staining was observed, with no roughness due to tactile inspection and the evaluation by transillumination and impression showed no cavitation. The following preventive treatment plan was endorsed: oral hygiene instructions with emphasis to the importance of flossing the proximal areas, and healthy dietary habits. After a 5-years period of follow-up, the enhanced oral hygiene and heathy dietary habits were observed. A clinical examination with immediate tooth separation and bitewing radiographs was performed and showed no cavitation. The combination of methods for detecting carious lesions in proximal surfaces was effective in obtaining a diagnosis of caries in the permanent dentition. The absence of cavitated lesions must be indicative of preventive treatment. (AU).

Este caso clínico objetivou relatar e discutir os métodos diagnósticos para detecção e tratamento preventivo de lesões cariosas proximais. A paciente procurou atendimento restaurador com queixa de cárie diagnosticada por exame radiográfico realizado após término de seu tratamento ortodôntico. Ao exame clínico não havia suspeita de lesão cariosa. A avaliação radiográfica revelou, na face mesial do dente 25, presença de área radiolúcida limitada à metade externa do esmalte. Para confirmação do diagnóstico realizou-se a separação interdentária imediata, porém como a mesma não permitiu adequada visualização foi realizada a separação mediata e após 24 horas obteve-se adequada separação (1 mm) para o exame clínico. Em seguida, a superfície proximal foi avaliada por transiluminação e moldagem. Durante a inspeção visual foi constatada área de manchamento do esmalte, com ausência de rugosidade pela inspeção tátil e a avaliação tanto por transiluminação da superfície proximal, quanto por moldagem revelou ausência de cavitação. Devido o diagnóstico obtido o seguinte tratamento preventivo foi indicado: reforço de higiene oral com ênfase na importância do uso do fio dental e hábitos dietéticos saudáveis. Após 5 anos de acompanhamento melhoria da higiene oral e hábitos dietéticos foram constatados. O exame clínico com separação interdentária imediata e exame radiográfico revelaram ausência de cavitação. Conclui-se que a combinação de métodos de detecção de lesões cariosas proximais foi efetivo no diagnóstico da cárie dentária na dentição permanente. O resultado deste relato de caso mostrou que a ausência de lesões cariosas cavitadas deve ser um indicativo de tratamento preventivo.(AU).

Survival of extensively damaged endodontically treated incisors restored with different types of posts-and-core foundation restoration material.

STATEMENT OF PROBLEM: Which post-and-core combination will best improve the performance of extensively damaged endodontically treated incisors without a ferrule is still unclear. PURPOSE: The purpose of this in vitro study was to investigate the restoration of extensively damaged endodontically treated incisors without a ferrule using glass-ceramic crowns bonded to various composite resin foundation restorations and 2 types of posts. MATERIAL AND METHODS: Sixty decoronated endodontically treated bovine incisors without a ferrule were divided into 4 groups and restored with various post-and-core foundation restorations. NfPfB=no-ferrule (Nf) with glass-fiber post (Pf) and bulk-fill resin foundation restoration (B); NfPfP=no-ferrule (Nf) with glass-fiber post (Pf) and dual-polymerized composite resin core foundation restoration (P); NfPt=no-ferrule (Nf) with titanium post (Pt) and resin core foundation restoration; and NfPtB=no-ferrule (Nf) with titanium post (Pt) and bulk-fill resin core foundation restoration (B). Two additional groups from previously published data from the same authors (FPf=2mm of ferrule (F) and glass-fiber post (Pf) and composite resin core foundation restoration; and NfPf=no-ferrule (Nf) with glass-fiber post (Pf) and composite resin core foundation restoration), which were tested concomitantly and using the same experimental arrangement, were included for comparison. All teeth were prepared to receive bonded glass-ceramic crowns luted with dual-polymerized resin cement and were subjected to accelerated fatigue testing under submerged conditions at room temperature. Cyclic isometric loading was applied to the incisal edge at an angle of 30 degrees with a frequency of 5 Hz, beginning with a load of 100 N (5000 cycles). A 100-N load increase was applied every 15000 cycles. The specimens were loaded until failure or to a maximum of 1000 N (140000 cycles). The 6 groups (4 groups from the present study and 2 groups from the previously published study) were compared using the Kaplan-Meier survival analysis (log-rank post hoc test at α=.05 for pairwise comparisons). RESULTS: None of the tested specimen withstood all 140 000 cycles. All specimens without a ferrule were affected by an initial failure phenomenon (wide gap at the lingual margin between the core foundation restoration/crown assembly and the root). NfPfP, NfPt, and NfPtB had similar survival (29649 to 30987 mean cycles until initial failure). NfPfB outperformed NfPt and NfPtB. None of the post-and-core foundation restoration materials were able to match the performance of the ferrule group FPf (72667 cycles). In all groups, 100% of failures were catastrophic. CONCLUSIONS: The survival of extensively damaged endodontically treated incisors without a ferrule was slightly improved by the use of a fiber post with a bulk-fill composite resin core foundation restoration. However, none of the post-and-core techniques was able to compensate for the absence of a ferrule. The presence of the posts always adversely affected the failure mode.

Morbidade materna grave na microrregião de Barbacena/MG / Severe maternal morbidity in the microregion of Barbacena, Minas Gerais state, Brazil

Resumo Introdução As complicações da gestação, parto e puerpério somam a décima causa de morte feminina e constituem um problema de saúde pública nos países menos desenvolvidos. Objetivo O objetivo deste estudo foi o de identificar os fatores associados à morbidade materna grave na microrregião de Barbacena, em Minas Gerais, no período de fevereiro a agosto de 2014. Métodos Estudo tipo caso-controle, no qual foram selecionadas como casos todas as puérperas que preencheram pelo menos um dos critérios para a morbidade e como controles as que não apresentaram nenhuma intercorrência. A análise dos fatores associados à morbidade foi realizada por meio de modelo de regressão logística. O nível de significância adotado foi de 5%. Resultados Foram avaliadas 276 mulheres, das quais 92 eram casos, e 184, controles. Na análise multivariada do modelo final de regressão logística, permaneceram as variáveis: história pregressa de hipertensão arterial (OR=20,8; IC95%=6,4-67,4), prematuridade (OR=7,5; IC95%=3,8-14,8) e parto cesáreo (OR=3,4; IC95%=1,69-6,76). Conclusão Houve uma relação forte entre as variáveis pesquisadas no presente estudo e a ocorrência de eventos adversos, com a importância da identificação precoce dos fatores de risco para morbidade materna e o estabelecimento de estratégias preventivas.

Abstract Background Complications during pregnancy, birth, and puerperium add up to the tenth death cause among women, and constitute a public health problem in developing countries. Objective The objective of this study was to identify the factors associated with severe maternal morbidity in the microregion of Barbacena, Minas Gerais state, Brazil from February to August 2014. Methods This is a case-control study where all puerperal women who met at least one criterion of morbidity were selected as case, whereas those who did not present any complications were considered as control. The factors associated with morbidity were analyzed using the logistic regression model at 5% significance level. Results The study assessed 276 women, of which 92 were cases and 184 were controls. In the multivariate analysis of the final logistic regression model, the variables that persisted were past medical history of high blood pressure (OR=20.8; CI 95%: 6.4-67.4), prematurity (OR=7.5; CI 95%: 3.8-14.8), and caesarean section (OR=3.4; CI 95%: 1.69-6.76). Conclusions A strong correlation was found between the variables investigated and the occurrence of adverse events, accentuating the importance of early identification of risk factors for maternal morbidity and establishment of preventive strategies.

Markers of bone remodeling in neoplastic and bone-related lesions.

OBJECTIVE: The aim of this study was to investigate the expression of bone resorption (RANK/RANKL), bone resorption inhibitor (osteoprotererin [OPG]), and bone formation marker (osteocalcin [OC]) in neoplastic and bone-related lesions (BRL). STUDY DESIGN: Using immunohistochemistry, their expression was evaluated in ossifying fibroma (OF), fibrous dysplasia (FD), simple bone cysts (SBC), central giant cell lesions (CGCL), and osteosarcoma (OS). RESULTS: Quantitative analyses of the expression of bone markers between all lesions, considering fibroblast-like cells and bone matrix, showed that RANK-RANKL presented higher expression in OF and CGCL, whereas OPG and OC presented higher expression in FD and SBC. There was higher expression of all proteins investigated when OS was the BRL. Moreover, the RANKL expression was greater than OPG in this neoplasm. CONCLUSION: Our data indicate that the bone resorption markers are more highly expressed in OF, CGCL, and OS than in FD and SBC, indicating a significant association between these proteins and the clinical behavior of these lesions.

Resultados perinatais de gestantes com Síndrome Hipertensiva da Santa Casa de Misericórdia de Barbacena, Minas Gerais: estudo controlado / Perinatal results of pregnant women with Hypertensive Syndrome from Santa Casa de Misericórdia of Barbacena, Minas Gerais: controlled study

Objetivo: descrever os resultados perinatais em gestantes hipertensas e normotensas atendidas na Santa Casa de Misericórdia de Barbacena (MG). Métodos: estudo transversal de 202 gestantes hipertensas e 398 normotensas, nas quais foram avaliadas as variáveis parto pré-termo, recém-nascido (RN) com baixo peso ao nascer, estado nutricional do recém-nascido, admissão em Unidade de Tratamento Intensivo (UTI), natimortalidade e mortalidade neonatal. As pacientes realizaram exames clínicos e laboratoriais para avaliar a gravidade e classificar o tipo de hipertensão arterial na gestação. Os recém-nascidos foram avaliados e acompanhados, comparando-se as variáveis perinatais com o tipo de hipertensão, características sociodemográficas e gestacionais e outros eventos de interesse, como tabagismo e assistência pré-natal. A análise univariada foi feita no Epi Info versão 6.04 e a análise multivariada, com o uso da regressão logística, no MINITAB versão 11.2...

Tratamento odontológico de pacientes portadores de deficiência mental com anestesia geral / Dental treatment of patients with mental disability using general anesthesia

O uso da anestesia geral para o tratamento odontológico em pacientes portadores de deficiência mental é um assunto polêmico e, em geral, desconhecido pelos cirurgiões-dentistas, que, por esse motivo, temem a sua indicação. O artigo apresenta uma revisão da literatura sobre o assunto, mostrando riscos, benefícios e descrições técnicas dessa forma de tratamento nessa classe de pacientes, que vem necessitando cada vez mais de tratamento especializado.