Two-Dimensional Theoretical Analysis and Experimental Study of Mass Transfer in a Hollow-Fiber Dialysis Module Coupled with Ultrafiltration Operations.

This research theoretically and experimentally develops a hollow-fiber dialysis module coupled with ultrafiltration operations by introducing a trans-membrane pressure during the membrane dialysis process, which can be applied to the waste metabolic end products in the human body for improving the dialysis efficiency. The solutes were transported by both diffusion and convection from the concentration driving-force gradient between retentate and dialysate phases across the membrane, compared to the traditional dialysis processes by diffusion only. A two-dimensional modeling of such a dialysis-and-ultrafiltration system in the hollow-fiber dialysis module was formulated and solved using the stream function coupled with the perturbation method to obtain the velocity distributions of retentate and dialysate phases, respectively. The purpose of the present work is to investigate the effect of ultrafiltration on the dialysis rate in the hollow-fiber dialyzer with ultrafiltration operations. A highest level of dialysis rate improvement up to about seven times (say 674.65% under Va=20 mL/min) was found in the module with ultrafiltration rate Vw=10 mL/min and membrane sieving coefficient θ=1, compared to that in the system without operating ultrafiltration. Considerable dialysis rate improvements on mass transfer were obtained by implementing a hollow-fiber dialysis-and-ultrafiltration system, instead of using the hollow-fiber dialyzer without ultrafiltration operation. The experimental runs were carried out under the same operating conditions for the hollow-fiber dialyzers of the two experimental runs with and without ultrafiltration operations for comparisons. A very reasonable prediction by the proposed mathematical model was observed.

Enhancing the Permeate Flux of Direct Contact Membrane Distillation Modules with Inserting 3D Printing Turbulence Promoters.

Two geometric shape turbulence promoters (circular and square of same areas) of different array patterns using three-dimensional (3D) printing technology were designed for direct contact membrane distillation (DCMD) modules in the present study. The DCMD device was performed at middle temperature operation (about 45 °C to 60 °C) of hot inlet saline water associated with a constant temperature of inlet cold stream. Attempts to reduce the disadvantageous temperature polarization effect were made inserting the 3D turbulence promoters to promote both the mass and heat transfer characteristics in improving pure water productivity. The additive manufacturing 3D turbulence promoters acting as eddy promoters could not only strengthen the membrane stability by preventing vibration but also enhance the permeate flux with lessening temperature polarization effect. Therefore, the 3D turbulence promoters were individually inserted into the flow channel of the DCMD device to create vortices in the flow stream and increase turbulent intensity. The modeling equations for predicting the permeate flux in DCMD modules by inserting the manufacturing 3D turbulence promoter were investigated theoretically and experimentally. The effects of the operating conditions under various geometric shapes and array patterns of turbulence promoters on the permeate flux with hot inlet saline temperatures and flow rates as parameters were studied. The distributions of the fluid velocities were examined using computational fluid dynamics (CFD). Experimental study has demonstrated a great potential to significantly accomplish permeate flux enhancement in such new design of the DCMD system. The permeate flux enhancement for the DCMD module by inserting 3D turbulence promoters in the flow channel could provide a maximum relative increment of up to 61.7% as compared to that in the empty channel device. The temperature polarization coefficient (τtemp) was found in this study for various geometric shapes and flow patterns. A larger τtemp value (the less thermal resistance) was achieved in the countercurrent-flow operation than that in the concurrent-flow operation. An optimal design of the module with inserting turbulence promoters was also delineated when considering both permeate flux enhancement and energy utilization effectiveness.

Economic Design of Solar-Driven Membrane Distillation Systems for Desalination.

Solar-driven membrane distillation (SDMD) for desalination is a feasible method to solve water and energy resource issues. The design and operation of SDMD is different from continuous and steady state processes, such as common chemical plants, due to the intermittent and unpredictive characteristics of solar radiation. Employing the steady state and dynamic simulation models developed on the platform of Aspen Custom Modeler®, this paper presents a two-stage design approach for the SDMD systems using different types of membrane distillation configurations, including AGMD (air gap MD), DCMD (direct contract MD) and VMD (vacuum MD). The first design stage uses the steady state simulation model and determines equipment sizes for different constant-value solar radiation intensities with the objective of minimizing total annual cost. The second design stage is implemented on the SDMD systems with process control to automatically adjust the operating flow rates using the dynamic simulation model. Operated with the yearly solar radiation intensity of Taiwan, the unit production costs (UPCs) of the optimal SDMD systems using AGMD, DCMD, and VMD are $2.71, 5.38, and 10.41 per m3 of water produced, respectively. When the membrane unit cost is decreased from $90/m2 to $36/m2, the UPC of the optimal solar-driven AGMD system can be reduced from $2.71/m3 to $2.04/m3.