The effect of artificial saliva on the rheological properties of tooth whitening systems.

This work was undertaken to explore the effect of saliva addition on the rheological properties of two contrasting tooth bleaching systems, one of which was a paste (Colgate Platinum) and the other a gel (Zaris, 3M ESPE). Using a dynamic stress rheometer with cone and plate geometry, it was shown that addition of artificial saliva reduced the apparent viscosity of each material. However, in some cases this was accompanied by an increase in elasticity. It is suggested that saliva may not have a deleterious effect on the ability of the materials to remain in the bleaching tray.

The effect of washing water on bonding to etched enamel.

There is current concern about bacterial contamination of dental unit waterlines. This research hypothesized that the presence of increasing concentrations of bacteria in water used to wash etched enamel would result in a corresponding decrease in both shear bond strength (SBS) and critical surface tension (gammaC) of enamel. A further hypothesis was made that there is a correlation between SBS and gammaC. The effect of 3.5 ppm iodine in the water as a bacteriostatic agent was also assessed. Five groups of 10 samples of bovine enamel were etched, washed, and a resin composite bonded to them. The control group was washed with distilled water. Another group was washed with the dilute iodine solution. The remaining three groups used a different concentration of Escherichia coli DH5alpha as follows (in cfu mL(-1)): group 1: 10(2); group 2: 10(4); group 3: 10(6). Shear bond strength data were measured on an Instron testing machine at a crosshead speed of 1 mm min(-1). Adhesion data were (MPa): control: 24.6 +/- 6.0; with iodine: 20.8 +/- 2.7; group 1: 19.8 +/- 2.7; group 2: 13.5 +/- 3.0; group 3: 13.9 +/- 3.6. The F-test yielded a highly significant difference between control group, iodine group and group 1, compared with groups 2 and 3 (P < 0.0001). Tukey's Studentized Range Test was used for pairwise comparison testing between groups. Using a Cahn dynamic contact angle analyzer and linear regression analysis, the plots of surface tension versus costheta were extrapolated to costheta = 1 to give gammaC data for the control group and groups 1-3. In all cases reasonable linearity was observed (r2 > or = 0.87). Data (mN m(-1)) were: control group: 50.8; group 1: 45.1; group 2: 43.2; group 3: 39.5. The SBS and gammaC were then plotted against each other and linear regression analysis performed. It was concluded that increasing concentrations of bacteria in wash water decreased both SBS and gammaC and that a linear correlation (R2 = 0.84) was found between the values of these two parameters.

A clinical pilot study of the time-dependent composition of tooth bleaching systems.

This pilot study was undertaken to determine the compositional changes in tooth bleaching materials as a function of time in vivo. Ten patients were recruited and two bleaching systems were used - one a paste and the other a gel. Each material was placed in a custom bleaching tray and worn by each patient for each of four times - 15, 30, 60 and 120 min. The material was collected and chemically analysed for water by Karl Fischer titration and titrated for carbamide peroxide by the US Pharmacopoeia method. The paste material contained 18.66% water as supplied, and after 2 h this rose to between 28.6 and 64.4%. The gel material contained 2.85% water as supplied, and after 2 h this was diluted to between 28.5 and 73.4%. There was considerable difference in saliva uptake by the custom tray between patients. Most water uptake usually occurred within the first 30 min. Peroxide concentrations decreased in an approximately linear manner with time. There was a significant difference between the materials from baseline to 30 min and thereafter (P < 0.0009). This pilot study is an effective technique for chemical evaluation of bleaching materials. The effect of saliva is an important factor to consider, and is one that has hitherto not always been appropriately emphasized.

Assessing restorative dental materials: 2. Questions for a dental sales representative.

Many methodologies are used during the testing of dental materials, although different tests are suitable for different materials and clinical situations. This paper discusses factors relevant to the choice of a dental material, and suggests questions that a practitioner would find helpful to ask a dental sales representative, such as ease of use, effect on the environment and the relevance of fluoride release.

Assessing restorative dental materials: I. Test methods and assessment of results.

Many methodologies are used during the testing of dental materials. Among these are compressive, tensile and flexural strengths, and fracture toughness. However, different tests are relevant to different materials and clinical situations. This paper describes different test methodologies and discusses the substantiation of research claims in publications and advertising.

Effects of restorative and adhesive curing methods on dentin bond strengths.

PURPOSE: To evaluate the shear bond strengths of "one-bottle" adhesives to dentin when used with self-cured composite. MATERIALS AND METHODS: 100 bovine teeth were ground to expose superficial dentin, which was polished to 600-grit. The dentin was etched for 15 s with 35% phosphoric acid, rinsed, and blotted with tissue paper. The surface remained visibly moist for all specimens. The following adhesives were applied to the etched dentin according to manufacturers' directions: Scotchbond Multi-Purpose (in its visible light-cured [VLC] and self-cure modes) as a control, One-Step (VLC only), OptiBond Solo Plus (VLC only), Prime & Bond NT (VLC) and Prime & Bond NT Dual-Cure. For each adhesive, specimens were bonded with a self-cure composite, while 10 were bonded with a VLC composite as a control. After 24 hrs water storage, shear bond strengths were determined using an Instron universal testing machine. Data were analyzed using two-way ANOVA, Tukey's test, and Student's t-tests. RESULTS: Using the light-cured composite, mean bond strengths ranged from 11.0 MPa for light-cured Prime & Bond NT to 26.3 MPa for OptiBond Solo Plus. Using the self-cure composite, mean bond strengths ranged from 0.0 for light-cured Prime & Bond NT to 21.4 MPa for One-Step. Two adhesives, light-cured Prime & Bond NT and OptiBond Solo Plus, had significantly lower bond strengths when used with the self-cure composite. CLINICAL SIGNIFICANCE: Some "one-bottle" dentin adhesives may not provide acceptable bonding to tooth structure when they are used with self-cure composites.

Alpha- and beta-forms of gutta-percha in products for root canal filling.

AIM: This study was undertaken to evaluate which materials were in the alpha-form of gutta-percha as claimed, and which were in the more conventional beta-form, and to explore the effect of heating on the materials. METHODOLOGY: Samples of gutta-percha without chemical additives, and dental gutta-percha formulations which included (i) two products previously studied; (ii) 12 newer products; and (iii) one newer product that had been stored at high temperature, were analysed by simultaneous differential thermal analysis and thermogravimetry. RESULTS: It was found that only four of the newer materials contained the alpha-form; all the rest comprised beta-gutta-percha. No weight loss was found for any material under the conditions of the present experiments. A typical heating cycle up to 130 degrees C caused changes in material behaviour - that is, on reheating fewer endothermic peaks were present. Storage of gutta-percha samples for 10 years under ambient temperature and storage in a heater at 80 degrees C appeared to have no effect on properties. CONCLUSIONS: It was concluded that heating dental gutta-percha to 130 degrees C causes physical changes; this was not seen with chemically pure gutta-percha. The presence of additives in the dental samples altered material behaviour.

Rheological properties of vinyl polysiloxane impression pastes.

OBJECTIVES: Some vinyl polysiloxane impression (VPS) materials are claimed to be 'thixotropic' so that they will have 'non-drip' properties and not flow off an impression tray during insertion of the material into the mouth. This work was carried out to investigate rheological properties of VPS materials by determination of their flow properties under different experimental conditions relevant to their dental application. METHODS: The rheological characteristics of each component paste of two low viscosity VPS materials were assessed by a Dynamic Stress Rheometer using cone and plate geometry. RESULTS: Both pastes of one product (Imprint II) showed a yield stress of around 40 Pa in addition to some degree of true thixotropy. In contrast, both Examix pastes had no yield stress value, but the catalyst paste was markedly thixotropic, as shown by a drop in viscosity as a result of application of shear force over time. Both products had thixotropic properties. The Imprint II in addition showed a yield stress that would also contribute to the 'non-drip' properties. SIGNIFICANCE: Combination of yield stress and thixotropy will prevent the undesirable drip of the materials once it has been injected around the tooth preparation until the impression tray is loaded and seated. After seating the tray, a thixotropic material will not flow.

Shear bond strength of stainless steel orthodontic brackets with a moisture-insensitive primer.

The purposes of this study were (1) to evaluate the shear bond strength of stainless steel orthodontic brackets bonded to dry and wet (with water and saliva) etched enamel with the use of the moisture-insensitive primer (MIP; Transbond; 3M Unitek, Monrovia, Calif) and (2) to evaluate the effectiveness of MIP with chemically activated (Concise; 3M Dental Products, St Paul, Minn) and light-activated (Transbond XT; 3M Unitek) resin. One hundred forty-four freshly extracted bovine teeth were divided into 12 groups (n = 12 teeth), and brackets were bonded with either of the 2 resins in combination with the conventional primer or MIP in dry or wet enamel surface conditions. The test specimens were mounted in a screw-driven mechanical testing machine (model 4204; Instron Corp, Canton, Mass) and subjected to a crosshead speed of 0.5 mm/min. The data were analyzed by 2-way analysis of variance. MIP with Concise produced slightly higher bond strengths compared with the conventional primers under wet conditions (MIP vs conventional: saliva, P <.001; water, P =.004). However, MIP in combination with Transbond XT produced comparable bond strengths on both the dry and wet etched enamel (dry, 10.14 MPa; water, 9.69 MPa; saliva, 8.90 MPa). The results of this study suggest that MIP be used only with light-activated composite resins.

Effect of surface treatments on the wettability of vinyl polysiloxane impression materials.

STATEMENT OF PROBLEM: A number of vinyl polysiloxane (VPS) impression materials are claimed to be hydrophilic, but it has been hypothesized that the degree of hydrophilicity may be altered by the exposure to saliva, disinfecting agents, and surfactants. PURPOSE: This study compared the effects of 6 treatment regimes on the hydrophilicity of 3 VPS materials. MATERIAL AND METHODS: Three VPS materials (Dimension Garant L, Hydroflex, Imprint II, referred to as G, H, and I, respectively) were each treated with: (1) nothing (control), (2) saliva, (3) saliva and NaOCl, (4) saliva and 2-propanol-based disinfectant, (5) saliva, NaOCl and surfactant, and 6) saliva, 2-propanol-based disinfectant, and surfactant. Advancing contact angles (thetaA) were measured using a Cahn Dynamic contact angle analyzer and WinDCA software. Using saturated CaSO4 solutions, thetaA was determined for the 3 materials in each of the 6 conditions. For each combination of VPS and treatment, 5 determinations were made using fresh samples and fresh solution each time. Considerable contact angle hysteresis was observed. Two-way ANOVA was performed, followed by post-hoc Boneferroni-Dunn tests. RESULTS: For all outcome variables, the treatment effects were not the same for all materials (P < .001). However, for all materials, treatments that included surfactants were among the groups with the lowest thetaA values and thus had the best wettability. For example, materials G and I, as made, had high thetaA values (109.7 and 115.2 degrees, respectively), but these values reduced to approximately 90 degrees after surfactant treatment. Material H had a thetaA value of 87.1 degrees. Exposure of material H to saliva and/or a disinfectant raised this value, but a thetaA close to the original value was achieved by the use of a surfactant. CONCLUSION: Treatments affected the VPS materials in different ways but, after disinfectant treatment, the wetting of "hydrophilic" VPS materials was improved by surfactant treatment.

Dentine bonding systems: 1. Mode of action.

The achievement of a reliable bond to dentine has been more difficult than bonding to enamel, due principally to the anatomy of the dentine substrate. The mechanisms of bonding are now much better understood than a decade ago and clinically-viable bond strengths to dentine are now achieved with many dentine bonding systems.

Dentine bonding systems: 2. Clinical uses.

As the reliability of dentine bonding agents has improved, the clinical uses of these systems has increased and now include the bonding of directly and indirectly constructed restorations, amalgam bonding and treatment of dentinal sensitivity. Areas of potential use which require further evaluation include pulp capping and the attachment of fractured tooth fragments.

Rheological characteristics of tooth bleaching materials.

Tooth bleaching materials need to flow easily on insertion but should have high viscosity at low stresses to stay in place on the teeth. Some degree of elasticity may also aid retention on the teeth thereby maximizing efficacy. The present work was undertaken to study the comparative rheology of three tooth bleaching systems: two gels (Opalescence, Ultradent; Perfecta Trio, American Dental Hygienics) and a paste (Colgate Platinum, Colgate). A dynamic stress rheometer (Rheometrics Scientific) with cone and plate geometry was used, with the materials maintained at 37.0+/-0.1 degrees C with a vapour hood to minimize volatilization. Stress creep and recovery experiments were carried out. Steady shear viscosity for all three systems was high (>10(6) Pa s(-1)) for stresses <20 Pa. Between 100 and 200 Pa stress, all three materials showed a large drop in viscosity and flowed readily. The recovery portion of the data showed a marked difference where the elasticity of the gels was nearly two orders of magnitude higher than that of the paste. It was concluded that all materials would flow readily on insertion into the mouth and all have desirable high viscosity at low stress, but the paste material had the lowest elasticity. The effect of elasticity on performance needs to be determined clinically.

Contemporary resin-based composite materials for direct placement restorations: packables, flowables and others.

Resin-based composite (RBC) materials are composed of principal and diluent monomers, fillers, coupling agents and other components. These materials have been developed in recent years to produce packable and flowable materials, and materials which may release ions under specific conditions and which may contain fibres. Materials which are organic-inorganic copolymers have also become available. Long term clinical trial data are not available for the most recently introduced materials.

Fracture resistance of five pin-retained core build-up materials on teeth with and without extracoronal preparation.

Core build-ups should provide satisfactory strength and resistance to fracture both before and after crown preparation. This paper examines the resistance to fracture of core build-ups in different materials and the fracture resistance of core build-ups when these have been reduced for full crown preparation. Standardized core build-ups were made on groups of extracted molar teeth of similar size, with 10 teeth per group. Three resin-composite (prisma APH: Dentsply, Weybridge, UK; Ti-Core, Essential Dental Systems, NJ, US and Coradent, Vivadent, Liechtenstein), one cermet (Ketac-Silver, ESPE GmbH, Seefeld, Germany) and one amalgam material (Duralloy, Degussa Ltd, Cheshire, UK). These specimens were subjected to compressive force on a universal testing machine and the force at fracture noted. Standardized full crown preparations were made on a further five groups of core build-up specimens using the same materials as above. These prepared specimens were subjected to compressive force on a universal testing machine and the force to fracture noted. The results indicated that amalgam core build-ups demonstrated higher fracture resistance than the other materials examined. There was a general decrease in the fracture strength of the specimens following crown preparation, with the teeth restored with the amalgam core build-ups showing a greater percentage reduction in fracture strength than the other materials tested. Prepared core build-ups in a hybrid composite material provided the highest fracture resistance. The cermet material used provided the lowest resistance to fracture in both the core build-up and crown preparation specimens. In terms of fracture resistance, no advantage was apparent in using the two composite materials designated as being specifically appropriate for core build-ups.

Mechanical properties of direct core build-up materials.

OBJECTIVE: This work was undertaken to measure mechanical properties of a diverse group of materials used for direct core build-ups, including a high copper amalgam, a silver cermet cement, a VLC resin composite and two composites specifically developed for this application. METHODS: Compressive strength, elastic modulus, diametral tensile strength and flexural strength and modulus were measured for each material as a function of time up to 3 months, using standard specification tests designed for the materials. RESULTS: All the materials were found to meet the minimum specification requirements except in terms of flexural strength for the amalgam after 1 h and the silver cermet at all time intervals. SIGNIFICANCE: There proved to be no obvious superior material in all respects for core build-ups, and the need exists for a specification to be established specifically for this application.

Magnetron sputtered tin coatings on unbiased ceramic substrates.

OBJECTIVES: The aim of this work was to study the application of tin oxide coatings on alumina, with a view to developing improved bonding for high-alumina dental ceramics. METHODS: By use of a magnetron sputtering technique, alumina was coated with tin which was subsequently oxidized, and the bond strength of coated surfaces to a resin-based dental cement was measured in tension. Tensile bond strength data were assessed for their degree of skewness and the homogeneity of the residual variances with a view to applying appropriate transformations prior to performing ANOVA with subsequent Tukey's analysis as necessary. The color of coatings, as a function of the amount of oxidation of the surface, was noted. Coatings were characterized by SEM and EDAX. It has been found possible to produce esthetic tin oxide coatings on alumina using a simplified magnetron sputtering apparatus in conjunction with post-deposition oxidation. RESULTS: Although mean tensile bond strength (TBS) values in excess of 15 MPa were recorded for a number of groups, no causal relationship was found between coating time and mean TBS. SIGNIFICANCE: The need exists for improved bonding of alumina-based ceramics; further development of a magnetron sputtering technique may provide the means for achieving this.

The future of dental materials.

This article reviews some of the rapid developments in dental materials that have occurred during the last 25 years, especially adhesive, biocompatible and aesthetic materials. Some innovative research developments, which have exciting possibilities for future dental treatment, are outlined.

A new single-step technique for apical retrofilling that significantly reduces microleakage.

One of the properties of an ideal retrofilling material is little or no microleakage. A new dentin bonding agent based on polyacrylic acid (PAA) is ideally suited to the moist apical environment because of its hydrophilic nature. PAA as a dentin bonding agent for apical retrofillings was tested in an in vivo leakage study using single canal roots of extracted human teeth. Bonding was attained by pretreatment of the dentin in apical retrofilling preparations with a solution of PAA, followed by placement of a nonaqueous restorative material. Using PAA as dentin bonding agent reduced apical leakage at statistically significant levels with Super EBA as a restorative material. In vivo testing is required to validate these findings.

Properties of gypsum with the addition of gum arabic and calcium hydroxide.

The purpose of this work was to study the effects of adding a mixture of gum arabic and calcium hydroxide to a type III stone and an improved die stone. The effect on the water/powder ratio, compressive and tensile strength, hardness, and setting expansion was determined. Data for mechanical properties were subjected to two-way analysis of variance, followed by the Bonferroni-Dunn procedure to determine any significance (1%) between pairs of means. For the type III material the additives had little effect on setting expansion, but the additives significantly improved surface hardness. The additives did not improve compressive or tensile strength for the type III materials. In contrast, the improved die stone's hardness was not enhanced by the additives, and in some instances a reduction in strength was observed. It was concluded that dental cast materials with superior surface properties can be produced by a simple change of formulation.