RESUMEN
PURPOSE: To evaluate the wear resistance of a printed interim resin manufactured with different printing and postpolymerization parameters. MATERIALS AND METHODS: Overall, 130 rectangular resin specimens (15 × 10 × 10 mm) were 3D-printed. Among the specimens, 60 were printed with different printing orientations (0, 45, and 90 degrees) and layer thicknesses (50 and 100 µm) to create six groups to investigate the effects of the printing parameters (n = 10 per group). The remaining 70 specimens were used to evaluate the effects of postpolymerization; for this, seven groups were created as follows (n = 10 per group): nonpostpolymerized; postpolymerized for 5, 15, and 30 minutes with an ultraviolet light-emitting diode (LED) device; and postpolymerized for 5, 15, and 30 minutes with an ultraviolet light bulb device. After masticatory simulation, the wear volume loss was calculated with 3D metrology software. One-way and two-way ANOVA were used for intergroup comparisons (α = .05). RESULTS: The group printed with a build angle of 45 degrees showed lower wear volume loss than the 0- and 90-degree groups (P < .01). The wear volume loss in the ultraviolet LED group was significantly greater than that in the ultraviolet light bulb group (P = .04). No significant difference was observed in the wear volume loss of the printed resin with respect to the layer thickness and polymerization time (P > .05). However, the non-postpolymerized group showed significantly greater wear volume loss than the other groups (P < .001). CONCLUSIONS: The printed resin showed greater wear resistance when it was printed at a build angle of 45 degrees and postpolymerized with an ultraviolet light bulb device.
Asunto(s)
Impresión Tridimensional , Programas Informáticos , Ensayo de Materiales , Simulación por ComputadorRESUMEN
OBJECTIVES: Evidence on the reliability of digital techniques for wear volume assessment using three-dimensional (3D) scan datasets is scarce. This study evaluated the reliability of a repeated-scan superimposition technique and two single-scan techniques in assessing wear volume loss on flat surfaces of 3D-printed resin specimens. METHODS: Cuboid-shaped (15×10×10 mm) resin specimens were 3D-printed (n = 14) and scanned before and after 200,000 cycles of masticatory simulation. For the repeated-scan superimposition technique, digital 3D models of specimens before and after masticatory simulation were superimposed, and the volume loss was determined. The first single-scan technique utilized a computer-aided design freeware program, while the second one employed a 3D-metrology software program. In the freeware program, the worn area of 3D objects was edited directly to obtain a flat surface. In the 3D-metrology software program, the worn area was deleted first and then filled to the flat surface. The volume differences before and after editing were calculated in each software program. Agreement between the three measurement techniques was determined through intraclass correlation coefficients (ICCs). One-way analysis of variance was performed to compare the wear volume loss assessed by the three techniques (α = 0.05). RESULTS: High inter-technique reliability was observed between the three assessment techniques (ICC = 0.998, p < .001). On pair-wise comparisons of two of the three techniques, all pairs showed high consistency (ICC ≥ 0.999, p < .001). No significant difference was found in the wear volume loss assessed using the three techniques (p = .996). CONCLUSIONS: Digital repeated-scan superimposition and two single-scan techniques demonstrated high reliability in assessing wear volume loss on flat surfaces. CLINICAL SIGNIFICANCE: The repeated-scan superimposition technique can be effectively utilized to assess wear volume loss of anatomically shaped specimens and flat surfaces. This study indicates that the single-scan techniques may serve as a suitable alternative to the repeated-scan superimposition technique when evaluating wear volume loss of flat surfaces.
Asunto(s)
Diseño Asistido por Computadora , Programas Informáticos , Reproducibilidad de los Resultados , Simulación por Computador , Imagenología Tridimensional/métodosRESUMEN
OBJECTIVES: Both resin-modified glass ionomer cement (RMGIC) and self-adhesive resin cement (SAC) may be suitable for cementation of full-coverage zirconia restorations. This retrospective study aimed to investigate the clinical outcomes of zirconia-based restorations cemented with RMGIC and compare them with those cemented with SAC. METHODS: Cases of full-coverage zirconia-based restorations cemented with either RMGIC or SAC between March 2016 and February 2019 were evaluated in this study. The clinical outcomes of the restorations were analyzed according to the type of cement used. In addition, cumulative success and survival rates were evaluated according to the cement and abutment types. Non-inferiority, Kaplan-Meier, and Cox hazard tests were conducted (α=.05). RESULTS: A total of 288 full-coverage zirconia-based restorations (natural teeth, 157; implant restorations, 131) were analyzed. Loss of retention occurred in only one case; a single-unit implant crown cemented with RMGIC, which decemented 4.25 years post-restoration. RMGIC was non-inferior to SAC in terms of loss of retention (<5%). For single-unit natural tooth restorations, the four-year success rates in the RMGIC and SAC groups were 100% and 95.65%, respectively (p=.122). For single-unit implant restorations, the four-year success rates in the RMGIC and SAC groups were 95.66% and 100%, respectively (p=.365). The hazard ratios of all the predictor variables, including cement type, were not significant (p>.05). CONCLUSIONS: Cementation of full-coverage zirconia restorations of both natural teeth and implants using RMGIC and SAC yields satisfactory clinical outcomes. Furthermore, RMGIC is non-inferior to SAC in terms of cementation success. CLINICAL SIGNIFICANCE: Cementation with RMGIC or SAC for full-coverage zirconia restorations has favorable clinical outcomes in both natural teeth and implants. Both RMGIC and SAC have advantages in the cementation of full-coverage zirconia restorations to abutments with favorable geometries.
Asunto(s)
Cementación , Cementos Dentales , Cementos de Resina , Estudios Retrospectivos , Cementos de Ionómero Vítreo , Circonio , CoronasRESUMEN
Current restorative methods of restoring worn or eroded dentition present drawbacks that may deter dentists or patients from pursuing complete mouth rehabilitation. A novel additive manufacturing approach using 3D-printed definitive composite resin restorations is described as a less technique-sensitive and more cost-effective alternative. These restorations are straightforward to repair, modify, or replace.
RESUMEN
STATEMENT OF PROBLEM: Interim restorations are often used along with mouth rinses during the healing period following surgical procedures. However, evidence regarding the color and surface properties of digitally fabricated interim restorations after oral rinsing is lacking. PURPOSE: The purpose of this in vitro study was to evaluate whether different mouth rinses could affect the color and surface roughness of milled and printed interim restorations after simulated oral rinsing. MATERIAL AND METHODS: Disk-shaped specimens (Ø15×2 mm; N=180) were fabricated by using conventional (Jet Tooth Shade), milled (Yamahachi PMMA Disk), and printed (NextDent C&B) resin materials. All resin specimens were divided into 3 different groups according to the rinsing material: distilled water, whitening mouth rinse (Listerine Healthy White), and conventional mouth rinse (Listerine Cool Mint). The specimens were further allocated into short- and long-term subgroups, and oral rinsing simulation was performed (n=10). Short-term rinsing simulated the conditions in a usual interim restoration period, and long-term rinsing was performed to evaluate the properties of the interim materials. The color differences (CIEDE2000, ΔE00) between the baseline and each time point were determined by using a spectrophotometer. The surface roughness of the tested specimens was measured by using a confocal laser scanning microscope. Kruskal-Wallis and Friedman tests with nonparametric pairwise comparisons were used to analyze the data (α=.05). RESULTS: On simulation of a 6-month use of the mouth rinse, the color change in the milled resin did not differ from that in the conventional resin (P>.334), but the printed resin showed a significantly greater color change than the other resins (P<.007). The greatest color change with the printed resin was observed when a conventional mouth rinse was used. However, all color changes were below a perceptible threshold of 1.30. When daily rinsing for 14 years was simulated, all resin groups showed a perceptible color change when conventional mouth rinse was used, and the printed resin showed the greatest median ±interquartile range ΔE00 (2.24 ±0.2). In both short- and long-term simulations, the printed resin rinsed with the conventional mouth rinse showed significantly greater roughness than that rinsed with distilled water (P<.009). CONCLUSIONS: The printed resin showed higher stainability than the conventional resin, and the color change was greatest with the conventional mouth rinse. However, in 6 months of daily mouth rinse simulation, all the tested resin materials exhibited imperceptible color change and clinically acceptable surface roughness.
Asunto(s)
Antisépticos Bucales , Diente , Materiales Dentales , Agua , Ensayo de Materiales , Propiedades de Superficie , ColorRESUMEN
Purpose Completely edentulous arches can be restored using various prosthetic modalities, and the treatment outcome may include masticatory and speech discomforts. This study aimed to investigate the current status of prosthetic restoration modalities used for completely edentulous patients and investigate the association between prosthetic restoration modalities and subjective discomfort in mastication and speech by analyzing nationwide big data.Methods Of 97,622 individuals, data from 1,576 adults aged ≥40 years with no natural teeth and no requirement for additional prosthetic treatments were included. Oral examination data were analyzed, and the prostheses of the edentulous arches were categorized as follows: CD, removable complete denture; OD, implant-retained overdenture; and IF, implant-supported fixed dental prosthesis. Discomforts in mastication and speech according to the prosthetic restorative modality groups was statistically analyzed using analysis of covariance (α = 0.05).Results The maxillary/mandibular prosthetic restorative modality most commonly used was CD/CD, followed by CD/OD, IF/IF, OD/OD, and CD/IF, with weighted percentages of 93.23%, 2.48%, 1.83%, 1.46%, and 0.84%, respectively. Even after adjusting for various covariates, masticatory discomfort in the CD/CD group was significantly greater than that in the OD/OD (P = 0.0004) and IF/IF (P = 0.0002). The CD/CD group also had significantly greater discomfort in speech than did the IF/IF group (P = 0.0119).Conclusions Most completely edentulous patients were rehabilitated with bimaxillary removable complete dentures; however, the discomforts in mastication and speech were the lowest when both arches were restored with implant-supported fixed restorations.
RESUMEN
STATEMENT OF PROBLEM: Three-dimensionally (3D)-printed composite resins have been marketed as materials for definitive restorations. However, limited information is available regarding the stability of the adhesive interface and the efficiency of 3D-printed composite resins. PURPOSE: The purpose of this in vitro study was to evaluate the integrity of the marginal adhesive interface before and after thermal and mechanical fatigue of an initial formulation of a 3D-printed composite resin and to evaluate the efficiency of this manufacturing method. MATERIAL AND METHODS: Freshly extracted molars were prepared for onlays and adhesively restored with either 3D-printed composite resin (VarseoSmile Crown Plus) (Group 3D), milled composite resin (Tetric CAD) (Group MCOMP), milled PMMA (Telio CAD) (Group PMMA), and milled lithium disilicate (IPS e.max CAD) (Group EM). Marginal analysis was performed under a scanning electron microscope before and after fatigue by thermomechanical cyclic loading, and initial and terminal percentages of continuous margin (%CM) were compared. The time required for the production of each type of restoration was recorded, and the production costs were also compared. RESULTS: Before aging, 3D, MCOMP, and EM presented comparable values of %CM (69.8%, 75.9%, and 63.1%, respectively) that were statistically significantly higher (P<.05) than those of PMMA (45.1%). After aging, 3D and EM had comparable results (44.7% and 43.7%, respectively), which were lower than those of the MCOMP group (68.5%) but higher than those of the PMMA group (20.5%). Regarding time efficiency, 3D printing took less time than MCOMP or PMMA if more than 8 restorations were fabricated. For the production costs, 3D printing was 5.5, 8.7, and 10.2 times less expensive than PMMA, MCOMP, and EM, respectively. The initial equipment cost was also lower for the additive manufacturing method. However, 3D printing did not always considerably reduce waste. CONCLUSIONS: In terms of marginal adaptation, the evaluated initial formulation of a 3D-printed composite resin behaved similarly to other well-established definitive restoration materials and better than milled PMMA, both before and after fatigue. Three-dimensionally printed resins present advantages in terms of equipment and consumable costs, even for a single restoration, but also for production time when more than 8 restorations were fabricated.
RESUMEN
PURPOSE: To evaluate the effect of light-curing exposure time and location on polymerization of a restorative bulk-fill resin composite to lute endocrowns. METHODS: A light-cured restorative bulk-fill resin composite (Filtek One Bulk Fill) was submitted to direct light-curing by a high-power LED light-curing unit for 20 seconds as the positive control group (n= 10). Five more groups (n= 10) were light-cured in a natural tooth mold from two sites (labial and lingual) through a nanohybrid resin composite CAD-CAM restoration (Lava Ultimate A2 LT), for different irradiation times: 90 seconds per site, 40 seconds per site, 30 seconds per site, 20 seconds per site and 10 seconds per site. Vickers microhardness measurements were made at two different depths and test/control ratios were calculated. Ratios of 0.8 were considered as an adequate level of curing. A quantile regression was run to identify the minimally sufficient time of light-curing, and a two-way ANOVA was used to compare the results to previous findings and evaluate the effect of curing location. RESULTS: Analysis showed that 40 seconds x 2 is the minimal irradiation time that presents a test/control ratio above 0.8. Quantile regressions showed that the required irradiation time to reach a test/control ratio of 0.8 at a confidence level of 95% is 41.5 seconds and 39.2 seconds at 200 µm and 500 µm depths in the luting agent, respectively. There was no statistically significant difference between microhardness of the two depths except for the irradiation time of 10 seconds. The two-site to three-site light curing comparison showed no statistically significant difference except for the 90-second time. CLINICAL SIGNIFICANCE: Systematic light-curing through the labial, lingual and occlusal surfaces of thick indirect restorations is not always required for sufficient polymerization and can even waste valuable clinical time especially in the case of multiple restorations luted with resin composites.
Asunto(s)
Luces de Curación Dental , Curación por Luz de Adhesivos Dentales , Resinas Compuestas , Diseño Asistido por Computadora , Cementos Dentales , Materiales Dentales , Cementos de Ionómero Vítreo , Dureza , Curación por Luz de Adhesivos Dentales/métodos , Ensayo de Materiales , Polimerizacion , Propiedades de SuperficieRESUMEN
OBJECTIVES: To compare gloss retention of four different resin composites with their corresponding CAD/CAM composite blocks. MATERIALS AND METHODS: Four direct resin composites (Filtek Supreme XTE A2 Body (3M, USA), Tetric EvoCeram A2 (Ivoclar Vivadent, Liechtenstein), GrandioSO x-tra A2 (VOCO, Germany), G-aenial Universal A2 (GC, Japan)), and their corresponding CAD/CAM composite blocks were tested. A total of 288 samples were prepared and three different tests were performed: brushing, exposition to acidic fluoride gel and exposition to alcoholic solution. Gloss values were obtained by means of a glossmeter at T0 before aging and T60 after 1 h of aging. RESULTS: Mean gloss values ranged from 0.9 after brushing tests to 79.0 after the alcohol test witnessing a high gloss variability depending on the materials and the aging test. Statistical analysis by means of two-way repeated measures ANOVA followed by Fisher's LSD post-hoc test revealed significant differences between materials, storage media, and their interactions. CONCLUSION: Gloss retention seems to be dependent on the composite type (direct or CAD/CAM block) and composite brand and varies in respect to the type of aging. CAD/CAM materials showed a higher resistance toward alcohol exposure.
Asunto(s)
Diseño Asistido por Computadora , Cepillado Dental , Japón , Ensayo de Materiales , Propiedades de Superficie , Cepillado Dental/métodosRESUMEN
Objectives: The aim of this study was to evaluate the effect of different enamel surface treatments on the micro-shear bond strength. Materials and methods: Sixty-four approximal surfaces from freshly extracted molars were randomly assigned to eight groups, according to combinations of the following enamel surface treatments: ground or unground, 37.5% phosphoric acid etching time of 15 or 30 s, and with or without primer application. The same bonding agent (Optibond FL™ Adhesive, Kerr) was then used for all groups, and a 1.8 mm diameter resin composite (Harmonize™, Kerr) cylinder was built up on the bonded surface. Samples underwent a shear force test at a crosshead speed of 1 mm/min until failure. Bond strength was calculated, and failure modes were inspected under an optical microscope. Results: Bond-strength values ranged from 8.2 MPa for 15 s etched unground enamel with primer application to 19.6 MPa for 30 s etched ground enamel without primer application. ANOVA and Fisher's LSD post hoc tests revealed significant differences between the groups. Conclusions: Etching time and grinding have a statistically significant effect on the micro-shear bond strength of a three-step etch-and-rinse adhesive system on enamel. Primer application does not seem to be beneficial for enamel adhesion.
RESUMEN
Purpose To explore fracture strength and failure behaviour of minimally invasive CAD-CAM composite resin overlay restorations.Methods Eighty bi- and tri-layer cylindrical overlay model including the restoration bonded over bovine tooth dentin (Groups D) and enamel-dentin (Groups E) were assembled (diameter 9 mm). Restorations were milled from CAD-CAM composite resin blocks (Brilliant Crios, Coltène/Whaledent AG) in different thicknesses (0.5mm, 1mm, 1.5mm, 2mm) and equally distributed in four Groups D and four Groups E (n=10). All specimens were submitted to an Hertzian load-to-failure contact test with spherical indenter. Critical loads were recorded in Newton and data were analysed using Kruskal-Wallis test for multiple and Mann-Whitney test for 2-samples comparisons (p < 0.05). Fragments were examined using SEM. The stress distribution for specimens with restorations of 0.5 mm and 2 mm was also investigated with FEA.Results For all specimens, the mean static loads in Newton increased with an increase in restoration thickness. On contrary, restorations with the same thickness displayed higher resistance values when bonded over enamel than dentin, except for the 2-mm thick restorations. A damage competition was detected between cone/median cracks originating at the loading contact area of the restorations and radial cracks beginning at their inner surface, with the former prevailing in restorations bonded on enamel and the latter being dominant for restorations bonded on dentin.Conclusions For bonded ultra-thin resin composite restorations (0.5 mm to 1.5 mm) enamel as bonding substrate assures higher critical loads to fracture than dentin. This influence gradually decreases as restoration thickened.
Asunto(s)
Recubrimiento Dental Adhesivo , Porcelana Dental , Animales , Bovinos , Resinas Compuestas , Cementos Dentales , Análisis del Estrés Dental , Dentina , Ensayo de Materiales , Cementos de Resina , Propiedades de SuperficieRESUMEN
Analysis of marginal adaptation of dental adhesive interfaces using scanning electron microscopy has proven to be a powerful nondestructive method to evaluate the quality of adhesion. This methodology is, however, time-consuming and needs expensive equipment. The purpose of this study was to evaluate the possibility and efficiency of using a digital optical microscope (DOM) to perform marginal analysis and to compare it with the scanning electron microscope (SEM) analysis. Fifteen defect-free molars were selected for this study. Class V cavities were prepared and restored with resin composite, and epoxy replicas were obtained from silicone impressions of the restored teeth. Custom-made image analysis software was then used to measure the percentage of the noncontinuous margins (NCM) of each sample. To compare the DOM to the gold standard, SEM, each sample was analyzed 10 times using the DOM and three times using the SEM, by the same experienced operator. The repeatability coefficient and concordance were evaluated, and a Bland and Altman analysis was used for comparison of the two methods of measurements. To validate the DOM analysis method, an ANOVA approach (Gage R R) was used. Repeatability and reproducibility, which are two components of precision to validate the DOM analysis system, were calculated. For this, the same restorations were analyzed by two additional operators three times with the DOM. The duration of each step of the analysis using both methods was also recorded as a secondary outcome. Regarding the repeatability of each method, the Friedman test showed no statistically significant difference within the repetitions of measurements by SEM and DOM (p = 0.523 and p = 0.123, respectively). Moreover, the Bland-Altman analysis revealed a bias of 0.86 and concluded no statistically significant difference between the two methods, DOM and SEM. ANOVA evaluated DOM measurement system variation including the variances of repeatability and reproducibility that represented, respectively, 0.3% and 4% of the variance components. Reproducibility or inter-operator variability represented the principal source of variability with a statistically significant difference (p = 0.024). The time required for analysis with SEM was almost double that of DOM. The use of digital optical microscopy appears to be a valid alternative to the SEM for the analysis of marginal adaptation of dental adhesive interfaces. Further studies to evaluate the effect of training of operators in digital optical microscopy could reveal higher accuracy for this method and inter-operator agreement when experience is gained.
RESUMEN
The purpose of this in-vitro study was to evaluate the fracture resistance and failure mode of non-invasively reinforced endodontically treated mandibular molars. Sixty freshly extracted defect-free mandibular molars were divided into four experimental groups with extensive MOD cavities on endodontically treated teeth with different restoration types and one control group with intact teeth (n = 12). The groups were as follows: "Normal": direct resin composite; "Ring": glass fiber-reinforced strip (Dentapreg) wrapped around buccal and lingual walls followed by direct resin composite; "Inlay": indirect CAD/CAM resin composite inlay; "Onlay": indirect CAD/CAM resin composite onlay; "Intact": Intact teeth (Control). Tetric EvoCeram and Adhese Universal (Ivoclar Vivadent) were used for direct restorations and Tetric CAD (Ivoclar Vivadent) adhesively luted with Adhese Universal and Variolink Esthetic LC (Ivoclar Vivadent) were used for indirect restorations. All teeth were submitted to thermo-mechanical cyclic loading. All samples were then submitted to a compressive load until fracture. Fracture load was noted and teeth were analyzed to classify the failure mode as either catastrophic (C) or non-catastrophic (NC). No statistically significant difference was found between fracture strength of the five groups when all specimens were considered (p = 0.1461). Intact group showed the lowest percentage of catastrophic failures (41.67%). Ring group presents less catastrophic failures (75%) than Normal group (83.34%), and failures of indirect restorations-Inlay and Onlay-were almost all catastrophic (91.67% and 100%, respectively).
Asunto(s)
Fracturas de los Dientes , Diente no Vital , Resinas Compuestas , Análisis del Estrés Dental , Resistencia Flexional , Humanos , Incrustaciones , Diente MolarRESUMEN
PURPOSE: To compare the gloss retention of four resin based materials, two direct resin composites (Tetric EvoCeram and Filtek Supreme) and two indirect resin composite CAD-CAM blocks (Tetric CAD and Lava Ultimate). METHODS: 36 samples of 1 mm thickness were readied of each test material and manually polished with polishing discs (Sof-Lex) up to the finest grit size. Three gloss measurements per sample were taken (one every 120 degrees of sample rotation) by means of a glossmeter (Novo-Curve) for a total of 60 values obtained per tested material. Samples of each material were then randomly divided into three equal groups and aged with 75% alcohol (Group 1), amine fluoride gel (Elmex gelée) (Group 2) or mechanical brushing (Group 3). Another set of gloss measurements was performed on all samples after 1 hour of aging. Gloss values were statistically evaluated by means of repeated measures ANOVA and Fisher's LSD post-hoc tests. RESULTS: Gloss retention values ranged from 59.0 (Tetric EvoCeram) to 70.9 (Lava Ultimate) for alcohol, from 59.3 (Filtek Supreme) to 67.5 (Lava Ultimate) for Elmex gelèe and from 33.3 (Tetric EvoCeram) to 53.4 (Lava Ultimate) for mechanical brushing. Statistical analysis revealed: (1) significant difference between intial and final gloss values for all materials and groups; (2) significant difference between final gloss values of all the materials in the alcohol group; (3) significant difference between final gloss values of Lava Ultimate and all the other materials in the Elmex gelèe group; (4) significant difference between final gloss values of Lava Ultimate and Tetric CAD with the other tested materials in the brushing group. CLINICAL SIGNIFICANCE: Direct resin composites in general are widely used, and CAD-CAM resin composite materials are becoming progressively more accessible. Making the choice between direct and indirect techniques is still a challenge, and understanding the advantages of CAD-CAM resin composites in the form of higher gloss retention, which translates into higher durability of esthetics, may be one the parameters facilitating the decision.
Asunto(s)
Resinas Compuestas , Diseño Asistido por Computadora , Pulido Dental , Ensayo de Materiales , Propiedades de Superficie , Cepillado DentalRESUMEN
PURPOSE: To evaluate the minimal irradiation time to reach a sufficient polymerization of a photopolymerizable restorative bulk-fill resin composite to lute endocrowns. METHODS: A photopolymerizable restorative bulk-fill resin composite (Filtek One Bulk Fill) was submitted to direct light-curing by a high power LED light-curing unit for 20 seconds as the positive control group (n = 10). Five more test groups (n= 10) were light-cured in a natural tooth mold from three sites (buccal, palatal and occlusal) under a 9.5 mm thick nanohybrid resin composite CAD-CAM endocrown (Lava Ultimate A2 LT), for different irradiation times: 90 seconds per site, 40 seconds per site, 30 seconds per site, 20 seconds per site and 10 seconds per site. Vickers microhardness measurements were made at two different depths and test/control ratios were calculated. Ratios of 0.8 were considered as an adequate level of curing. RESULTS: Analysis shows that 30 seconds x 3 was the minimal irradiation time that presented a test/control ratio above 0.8. Quantile regressions showed that the required irradiation time to reach a test/control ratio of 0.8 at a confidence level of 95% was 38 seconds and 37 seconds for 200 µm and 500 µm, respectively. There was no statistically significant difference between microhardness of the two depths except for the irradiation time of 10 seconds. A 120-second (40 seconds per buccal, palatal and occlusal site) light-curing of photopolymerizable bulk-fill resin composite to lute a resin composite CAD-CAM endocrown restoration can be considered sufficient to reach adequate polymerization.
Asunto(s)
Luces de Curación Dental , Curación por Luz de Adhesivos Dentales , Resinas Compuestas , Diseño Asistido por Computadora , Dureza , Ensayo de Materiales , PolimerizacionRESUMEN
Extraoral facial scanning using a mobile phone has emerged as a viable, cost-effective option for certain applications not requiring high precision, such as patient education and 3-dimensional (3D) digital smile design. This technological development is particularly promising for general practitioners (GPs) who may not be able to invest in expensive,complex digital impressioning devices. This article describes and illustrates a relatively simple and accessible workflow that avails digital 3D facial scanning benefits to GPs.
Asunto(s)
Teléfono Celular , Cara/anatomía & histología , Imagenología Tridimensional , Sonrisa , Diseño Asistido por Computadora , Humanos , FotogrametríaRESUMEN
In the original publication of the article, the author's name "Prof. René Daher" was inadvertently missed in the author group. This has been updated in this erratum. Also, the original article has been corrected.
RESUMEN
The goals of the present study were to evaluate, in vitro, the staining of different composite resins submitted to different common beverages, and to compare the staining effect of each of these solutions. A total of 288 specimens were randomly divided into six groups and immersed for 4 weeks in five staining solutions represented by red wine, orange juice, coke, tea and coffee or in artificial saliva as a control group. When analyzed over a black background, mean ΔE00 values varied from 0.8 for Venus Diamond, Saremco Microhybrid and ELS in saliva and Estelite Posterior in coke to 37.6 for Filtek Supreme in red wine. When analyzed over a white background, mean ΔE00 values varied from 0.5 for Saremco Microhybrid in saliva to 51.1 for Filtek Supreme in red wine. All materials showed significant changes in color after 4 weeks of immersion in staining solutions. Significant differences were found between the tested composite resins and also between the staining solutions.
Asunto(s)
Bebidas , Color , Resinas Compuestas/química , Materiales Dentales/química , Bebidas Gaseosas , Café , Jugos de Frutas y Vegetales , Técnicas In Vitro , Ensayo de Materiales , Distribución Aleatoria , Saliva Artificial , Espectrofotometría , Propiedades de Superficie , Té , VinoRESUMEN
The goal of this short communication is to present finite element analysis comparison of the stress distribution between CAD/CAM full crowns made of Lava Ultimate and of IPS e.max CAD, adhesively luted to natural teeth and to implant abutments with the shape of natural teeth. Six 3D models were prepared using a 3D content-creating software, based on a micro-CT scan of a human mandibular molar. The geometry of the full crown and of the abutment was the same for all models representing Lava Ultimate full crowns (L) and IPS e.max CAD full crowns (E) on three different abutments: prepared natural tooth (n), titanium abutment (t) and zirconia abutment (z). A static load of 400 N was applied on the vestibular and lingual cusps, and fixtures were applied to the base of the models. After running the static linear analysis, the post-processing data we analyzed. The stress values at the interface between the crown and the abutment of the Lt and Lz groups were significantly higher than the stress values at the same interface of all the other models. The high stress concentration in the adhesive at the interface between the crown and the abutment of the Lava Ultimate group on implants might be one of the factors contributing to the reported debondings of crowns.
Asunto(s)
Resinas Compuestas/química , Diseño Asistido por Computadora , Coronas , Pilares Dentales , Porcelana Dental/química , Diseño de Prótesis Dental , Análisis del Estrés Dental , Procesamiento de Imagen Asistido por Computador , Mandíbula , Ensayo de Materiales , Diente Molar , Microtomografía por Rayos XRESUMEN
OBJECTIVES: To evaluate the biomechanical influence of reconnecting the buccal and lingual walls of endodontically treated lower molar with a large MOD cavity. METHODS: 3D models were created from a micro-CT scan of an extracted intact lower human molar. Finite element analysis was then used to compare the stress distribution and displacement of the structures between different models: Unrestored MOD on ETT (Unrest), MOD on ETT restored with composite resin (Norm), MOD on ETT reinforced with a non-invasive ring (Ring) and intact tooth as the control (Int). RESULTS: This study showed that the Unrest model presented the highest stress values at the cervical level. The non-invasive Ring model showed the lowest stress values at the cervical level, and the lowest deflection of the cusps. CONCLUSIONS: Mechanically reconnecting the remaining tooth structures has a direct positive effect on stress distribution and deformation of the remaining structures. CLINICAL RELEVANCE: Reinforcing ETT in a non-invasive direct approach is efficient in terms of preserving sound tooth structures, reducing the time of treatment and eliminating the laboratory steps required to create the restorations.