RESUMEN
The large thickness COPV is designed by netting theory and the finite element simulation method, but the actual performance is low and the cylinder performance still cannot be improved after increasing the thickness of the composite winding layer. This paper analyzes the reasons for this and puts forward a feasible solution: without changing the thickness of the winding layer, the performance of COPV can be effectively increased by increasing the proportion of annular winding fiber. This method has been verified by tests and is supported by theory.
RESUMEN
Epoxy and epoxide composites have a wide range of outdoor applications wherein they are affected by ageing. In this study, epoxy casting plates and epoxy-based composite rods for use in overhead conductors were prepared. A concurrent investigation concerning the ageing of epoxy resins and their carbon fibre composites was carried out via artificially accelerated experiments under hygrothermal and salt mist conditions. The moisture penetration along the depth, water absorption, appearance, hardness, density of the epoxy resins, and variation patterns of the impact strength and tensile strength of the epoxy-based composites were investigated. The ageing mechanisms were explored using Fourier transform infrared spectroscopy (FTIR) and scanning electron microscopy (SEM). Both ageing modes had essentially similar influences on the properties of the resins and their composites; moreover, they did not significantly affect the chemical structure and microstructure of the epoxy resin, with the physical adsorption of water primarily observed during the ageing process. The moisture absorption behaviour of the epoxy obeyed Fick's law. Although the water penetration rate in the salt mist ageing mode was slightly higher than that in the hygrothermal ageing mode during the early ageing stage, it was essentially the same during the later stage. The final moisture absorption rate at saturation was approximately 1.1% under both modes. The flexural strengths and impact strengths of the composites in both ageing modes followed a similar trend. They decreased gradually with the ageing time and then stabilized at almost the same value. The flexural strength was reduced from 803 MPa to 760 MPa and the impact strength from 383 J/m2 to 310 J/m2, indicating a decrease of approximately 5.4% and 19%, respectively. The absorbed water during the ageing process caused micro-cracks at the interface between the fibres and resin, weakening the interfacial strength and reducing the mechanical properties of the composites.
RESUMEN
The heat resistant aluminum alloy wire composite material core conductor (ACCC/HW) which was used in overhead transmission lines is developed and studied in this work. The composite material core is carbon fiber/glass cloth reinforced modified epoxy resin composite. Tensile stress tests and stress-strain tests of both composite core and conductor are taken at 25 °C and 160 °C. Sag test, creep test and current carrying capacity test of composite conductor are taken. The stress of composite conductor are 425.2 MPa and 366.9 MPa at 25 °C and 160 °C, respectively. The sag of conductor of 50 m length are 95 mm, 367 mm, and 371 mm at 25 °C, 110 °C, and 160 °C, respectively. The creep strain are 271 mm/km, 522 mm/km, and 867 mm/km after 10 years under the tension of 15% RTS (Rated Tensile Strength), 25% RTS and 35% RTS at 25 °C, and 628 mm/km under 25% RTS at 160 °C, according to the test result and calculation. The carrying capacity of composite conductor is basically equivalent to ACSR (Aluminum Conductor Steel Reinforced). ACCC/HW is suitable in overhead transmission lines, and it has been used in 50 kV power grid, according to the results.
RESUMEN
Hybrid nanoparticles modified bisphenol A type epoxy/acid anhydride resin system applicable for filament winding forming process was studied using elastic core-shell rubber (CSR) nanoparticles with a large particle size (nearly 100 nm) and rigid nano-SiO2 particles with a small particle size (about 16 nm). The formulation, process properties, mechanical properties, thermal properties and microstructure of modified resin and its wound composite were studied. The results suggested that at the content of 10 phr CSR and 2 phr nano-SiO2, the resin system achieved optimum comprehensive performance. The viscosity of modified resin system was nearly 1000 mPa·s at 25 °C and service life was over 6 h. The resin tensile strength and modulus were 89 MPa and 3.5 GPa, while flexural strength and modulus reached 128 MPa and 3.2 GPa, respectively. The impact strength was 26.6 kJ·m-2, and the glass transition temperature (Tg) reached 145.9 °C. Modified epoxy resin enhanced the mechanical properties of carbon fiber reinforced wound composite. The tensile strength, tensile modulus and interlaminar shear strength were enhanced by 14.0%, 4.56% and 18.9%, respectively, compared with a composite based on unmodified resin. The above test results and scanning electron microscopy (SEM) analysis suggest that the hybrid nanoparticles modified resin system was suitable for carbon fiber wet filament winding products.
