Development and Calibration of a Microfluidic, Chip-Based Sensor System for Monitoring the Physical Properties of Water Samples in Aquacultures.

In this work, we present a compact, bifunctional chip-based sensor setup that measures the temperature and electrical conductivity of water samples, including specimens from rivers and channels, aquaculture, and the Atlantic Ocean. For conductivity measurements, we utilize the impedance amplitude recorded via interdigitated electrode structures at a single triggering frequency. The results are well in line with data obtained using a calibrated reference instrument. The new setup holds for conductivity values spanning almost two orders of magnitude (river versus ocean water) without the need for equivalent circuit modelling. Temperature measurements were performed in four-point geometry with an on-chip platinum RTD (resistance temperature detector) in the temperature range between 2 °C and 40 °C, showing no hysteresis effects between warming and cooling cycles. Although the meander was not shielded against the liquid, the temperature calibration provided equivalent results to low conductive Milli-Q and highly conductive ocean water. The sensor is therefore suitable for inline and online monitoring purposes in recirculating aquaculture systems.

Analytical and numerical modeling of nonlinear lamb wave interaction with a breathing crack with low-frequency modulation.

To characterize fatigue crack, an analytical calculation and finite element (FE) simulation of Lamb wave propagating through the region of a breathing crack in a two-dimensional(2D) isotropic plate were studied. Contact surface boundary conditions between the two surfaces of the vertical crack were considered to study contact acoustic nonlinearity (CAN) from the breathing contact crack in conjunction with the modal decomposition method, Fourier transform, and variational principle-based algorithm. Reflection and transmission coefficients in the fundamental frequency and second harmonic frequency were calculated and analyzed quantitatively. Different ratios of incident wave amplitude to crack width were studied to calculate CAN results related to micro-crack width. In addition, a low-frequency (LF) vibration(10 Hz) excitation was introduced to perturb the free surface vertical crack to close, and an interrogating Lamb wave(1 MHz) was used to study crack-related CAN in different conditions for interpreting the modulation mechanism. The contact boundary conditions between two surfaces of vertical crack were set which were dynamically changed due to the low frequency modulation. The clapping effects when the crack closed due to the modulation of the contact boundary conditions between the crack surfaces were studied and analyzed to get the quantitative correlation between CAN and LF modulation. The results obtained from the analytical model were compared with those from the FE simulation, showing good consistency. Knowledge of these effects is essential to correctly gauge the severity of surface cracks in the plate, which can be spotlighted in its application to quantitative evaluation of micro fatigue cracks in structural health monitoring(SHM).

Adaptive polarization photoacoustic computed tomography for biological anisotropic tissue imaging.

Most photoacoustic computed tomography (PACT) systems usually ignore the anisotropy of the tissue absorption coefficient, which will lead to the lack of information in reconstructed images. In this work, the effect is addressed of the possible optical absorption anisotropy of tissue on PACT images. The functional relationship is derived between the photoacoustic response and the polarization angle of the excitation light. An adaptive polarized light photoacoustic imaging (AP-PACT) approach is proposed and shown to make up for the lack of imaging information and achieve optimal image contrast when imaging samples with anisotropic optical absorption, by utilizing the standard deviation of photoacoustic response as the feedback signal in an adaptive data acquisition process. The method is implemented both on phantom and in vitro experiments, which show that AP-PACT can recover anisotropic absorption-related information from reconstructed images and thus significantly improve their quality.

Phase behavior of medium-length hydrophobically associating PEO-PPO multiblock copolymers in aqueous media.

HYPOTHESIS: The micellization of block copolymers of poly(ethylene oxide) (PEO) and poly(propylene oxide) (PPO) is driven by the dehydration of PPO at elevated temperatures. At low concentrations, a viscous solution of isolated micelles is obtained, whereas at higher concentrations, crowding of micelles results in an elastic gel. Alternating PEO-PPO multiblock copolymers are expected to exhibit different phase behavior, with altered phase boundaries and thermodynamics, as compared to PEO-PPO-PEO triblock copolymers (Pluronics®) with equal hydrophobicity, thereby proving the pivotal role of copolymer architecture and molecular weight. EXPERIMENTS: Multiple characterization techniques were used to map the phase behavior as a function of temperature and concentration of PEO-PPO multiblock copolymers (ExpertGel®) in aqueous solution. These techniques include shear rheology, differential and adiabatic scanning calorimetry, isothermal titration calorimetry and light transmittance. The micellar size and topology were studied by dynamic light scattering. FINDINGS: Multiblocks have lower transition temperatures and higher thermodynamic driving forces for micellization as compared to triblocks due to the presence of more than one PPO block per chain. With increasing concentration, the multiblock copolymers in solution gradually evolve into a viscoelastic network formed by soluble bridges in between micellar nodes, whereas hairy triblock micelles jam into liquid crystalline phases resembling an elastic colloidal crystal.

Revisiting impulsive stimulated thermal scattering in supercooled liquids: Relaxation of specific heat and thermal expansion.

Impulsive stimulated thermal scattering (ISTS) allows one to access the structural relaxation dynamics in supercooled molecular liquids on a time scale ranging from nanoseconds to milliseconds. Till now, a heuristic semi-empirical model has been commonly adopted to account for the ISTS signals. This model implicitly assumes that the relaxation of specific heat, C, and thermal expansion coefficient, γ, occur on the same time scale and accounts for them via a single stretched exponential. This work proposes two models that assume disentangled relaxations, respectively, based on the Debye and Havriliak-Negami assumptions for the relaxation spectrum and explicitly accounting for the relaxation of C and γ separately in the ISTS response. A theoretical analysis was conducted to test and compare the disentangled relaxation models against the stretched exponential. The former models were applied to rationalize the experimental ISTS signals acquired on supercooled glycerol. This allows us to simultaneously retrieve the frequency-dependent specific heat and thermal expansion up to the sub-100 MHz frequency range and further to compare the fragility and time scale probed by thermal, mechanical, and dielectric susceptibilities.

A Miniature, Fiber-Optic Vibrometer for Measuring Unintended Acoustic Output of Active Hearing Implants during Magnetic Resonance Imaging.

Making use of magnetic resonance imaging (MRI) for diagnostics on patients with implanted medical devices requires caution due to mutual interactions between the device and the electromagnetic fields used by the scanner that can cause a number of adverse events. The presented study offers a novel test method to quantify the risk of unintended output of acoustically stimulating hearing implants. The design and operating principle of an all-optical, MRI safe vibrometer is outlined, followed by an experimental verification of a prototype. Results obtained in an MRI environment indicate that the system can detect peak displacements down to 8 pm for audible frequencies. Feasibility testing was performed with an active middle ear implant that was exposed to several pulse sequences in a 1.5 Tesla MRI environment. Magnetic field induced actuator vibrations, measured during scanning, turned out to be equivalent to estimated sound pressure levels between 25 and 85 dB SPL, depending on the signal frequency. These sound pressure levels are situated well below ambient sound pressure levels generated by the MRI scanning process. The presented case study therefore indicates a limited risk of audible unintended output for the examined hearing implant during MRI.

All-optical dynamic analysis of the photothermal and photoacoustic response of a microcantilever by laser Doppler vibrometry.

Light absorption induced thermoelastic and photoacoustic excitation, combined with laser Doppler vibrometry, was utilized to analyze the dynamic mechanical behavior of a microcantilever. The measured frequency response, modal shapes, and acoustic coupling effects were interpreted in the framework of a simple Bernouilli-Euler model and quantitative 3D finite element method (FEM) analysis. Three opto-mechanical generation mechanisms, each initiated by modulated optical absorption and heating, were identified both by an analytical and finite element model. In decreasing order of importance, optically induced cantilever bending is found to be caused by: (i) differences in photoacoustically induced pressure oscillations in the air adjacent to the illuminated and dark side of the cantilever, resulting from heat transfer from the illuminated cantilever to the nearby air, acting as a volume velocity piston, and (ii) thermoelastic stresses accompanying temperature and thermal expansion gradients in the cantilever, (iii) photoacoustically induced pressure oscillations in the air adjacent to the illuminated cantilever holder and frame.

Time-resolved thermal lens investigation of glassy dynamics in supercooled liquids: Theory and experiments.

This work reports results on the simultaneous spectroscopy of the specific heat and thermal expansivity of glycerol by making use of a wideband time-resolved thermal lens (TL) technique. An analytical model is presented which describes TL transients in a relaxing system subjected to impulsive laser heating. Experimentally, a set of TL waveforms, from 1 ns to 20 ms, has been recorded for a glycerol sample upon supercooling, from 300 to 200 K. The satisfactory fitting of the TL signals to the model allows the assessment of relaxation strength and relaxation frequency of the two quantities up to sub-100 MHz, extending the specific heat and thermal expansion spectroscopy by nearly three and eight decades, respectively. Fragility values, extracted from the relaxation behavior of the specific heat and the thermal expansion coefficient, are found to be similar, despite a substantial difference in relaxation strength.

Safety of active auditory implants in magnetic resonance imaging.

Magnetic resonance imaging (MRI) has become the gold standard for the diagnosis of many pathologies. Using MRI in patients with auditory implants can however raise concerns due to mutual interactions between the implant and imaging device, resulting in potential patient risks. Several implant manufacturers have been working towards more MRI safe devices. Older devices are however often labelled for more stringent conditions, possibly creating confusion with patients and professionals. With this myriad of different devices that are implanted in patients for lifetimes of at least 20 years, it is crucial that both patients and professionals have a clear understanding of the safety of their devices. This work aims at providing an exhaustive overview on the MRI safety of active auditory implants. The available industry standards that are followed by manufacturers are outlined and an overview of the latest scientific developments focusing on the last five years is provided. In addition, based on the analysis of the adverse events reported to the Food and Drug Administration (FDA) and in literature within the past ten years, a systematic review of the most commonly occurring issues for patients with auditory implants in the MRI environment is provided. Results indicate that despite the release of more MRI conditional active hearing implants on the market, adverse events still occur. An extensive overview is provided on the MRI safety of active auditory implants, aiming to increase the understanding of the topic for healthcare professionals and contribute to safer scanning conditions for patients.

Discrimination of 2D wall textures by passive echolocation for different reflected-to-direct level difference configurations.

In this work, we study people's ability to discriminate between different 2D textures of walls by passive listening to a pre-recorded tongue click in an auralized echolocation scenario. In addition, the impact of artificially enhancing the early reflection magnitude by 6dB and of removing the direct component while equalizing the loudness was investigated. Listening test results for different textures, ranging from a flat wall to a staircase, were assessed using a 2 Alternative-Forced-Choice (2AFC) method, in which 14 sighted, untrained participants were indicating 2 equally perceived stimuli out of 3 presented stimuli. The average performance of the listening subjects to discriminate between different textures was found to be significantly higher for walls at 5m distance, without overlap between the reflected and direct sound, compared to the same walls at 0.8m distance. Enhancing the reflections as well as removing the direct sound were found to be beneficial to differentiate textures. This finding highlights the importance of forward masking in the discrimination process. The overall texture discriminability was found to be larger for the walls reflecting with a higher spectral coloration.

Visualization of ultrasonic wave field by stroboscopic polarization selective imaging.

A stroboscopic method based on polarization selective imaging is proposed for dynamic visualization of ultrasonic waves propagating in a transparent medium. Multiple independent polarization parametric images were obtained, which enabled quantitative evaluation of the distribution of the ultrasonic pressure in quartz. In addition to the detection of optical phase differences δ in conventional photo-elastic techniques, the azimuthal angle φ and the Stokes parameter S2 of the polarized light are found to be highly sensitive to the wave-induced refraction index distribution, opening a new window on ultrasonic field visualization.

Optical wavelength dependence of photoacoustic signal of gold nanofluid.

We investigate the optical wavelength dependence of the photoacoustic (PA) signal, detected with bandwidth (BW) in the MHz range, of gold nanospheres (NSs) immersed in water upon illumination with ns laser pulses. We compare the wavelength dependence of the PA signal (within the MHz BW) with the one of the optical absorption coefficient as determined from optical transmission measurements. Thermal boundary conductance (TBC) at the gold-water interface is taken into account, as well as the temperature dependence of the thermal expansion coefficient of water. The effects of NS size and laser pulse duration on the PA signal are also explored. The PA signal is investigated with an opto-thermo-acoustic model considering light absorption in gold NS and in a surrounding water shell.

Conformal Prediction Based on Raman Spectra for the Classification of Chinese Liquors.

This work extends the conventional back-propagation neural network (BPNN) to the classification of Chinese liquors of different flavors according to their Raman spectra. Conformal prediction is applied to assign reliable confidence measures for each classification and support an effective framework to make the machine learning on classification trustable. The BPNN can be used to predict the flavors of Chinese liquors according to their Raman spectra, and a classification rate of 88.96% can be achieved. In order to evaluate each classification, a non-conformity score is defined to generate a P-value for each classification. Moreover, the validity of conformal prediction in online mode is discussed. The number of cumulative errors in the conformal prediction is much less than that without conformal prediction. The relationship between the cumulative error and confidence levels shows that a high confidence level leads to low cumulative errors, but many cumulative errors will occur under a very high confidence level. The result implies that conformal prediction is a useful framework, which can employ classification satisfying a certain level of confidence. Meanwhile, the conformal prediction can improve our classification using a BPNN, when the number of data points is limited.

Photoacoustic temperature imaging based on multi-wavelength excitation.

Building further upon the high spatial resolution offered by ultrasonic imaging and the high optical contrast yielded by laser excitation of photoacoustic imaging, and exploiting the temperature dependence of photoacoustic signal amplitudes, this paper addresses the question whether the rich information given by multispectral optoacoustic tomography (MSOT) allows to obtain 3D temperature images. Numerical simulations and experimental results are reported on agarose phantoms containing gold nanoparticles and the effects of shadowing, reconstruction flaws, etc. on the accuracy are determined.

Assessment of short-term exposure to an ultrasonic rodent repellent device.

The objectives of the present study were to investigate the acoustical properties of the very high frequencies and/or ultrasound signals produced by a repellent device and to investigate potential adverse factors as a result of short-term exposure to these signals. Potential adverse effects were evaluated perceptually with 25 young and 25 middle-aged persons, all with normal hearing thresholds, in a quiet room using different outcome measures, including a 15-item survey presented before and immediately after each condition. Spectral analyses showed that, besides emitting frequency modulated sounds in the expected frequency ranges, a faint but audible sound in the 4-5 kHz range was present. On average, a relatively short exposure to the sound produced by a repellent device did not lead to significant adverse effects. Yet, when the signal was perceived, as it was frequently for the younger population at the two lower frequencies settings (12-14 kHz, 25-25 kHz) and with 2 sources emitting, it was considered to be disturbing by several participants. Given the increasing usage of ultrasonic devices as well as the much longer exposure of high frequency and ultrasound in domestic usage, careful consideration and better guidelines are required, especially for those who are most sensitive to sound.

Conformational Changes of a Surface-Tethered Polymer during Radical Growth Probed with Second-Harmonic Generation.

The surface-induced polymerization of a chromophore-functionalized monomer was probed in situ for the first time using a nonlinear optical technique, second-harmonic generation. During the first hours of the polymerization reaction, dramatic changes in the tilt angle of the chromophore-functionalized side groups were observed. Following evaluation of the nonlinear optical data with those obtained from atomic force microscopy and ultraviolet-visible, we conclude that second-harmonic generation efficiently probes the polymerization reaction and the conformational changes of the surface-grafted polymer. With polymerization time, the conformation of the surface-tethered polymer changes from a conformation with the polymer backbone and its side groups flat on the surface, i.e., a "pancake" conformation, to a conformation where the polymer backbone is stretched away combined with tilted side groups or an enlarged tilt angle distribution, i.e., a "brush-type" conformation.

Texture in steel plates revealed by laser ultrasonic surface acoustic waves velocity dispersion analysis.

A photoacoustic, laser ultrasonics based approach in an Impulsive Stimulated Scattering (ISS) implementation was used to investigate the texture in polycrystalline metal plates. The angular dependence of the 'polycrystalline' surface acoustic wave (SAW) velocity measured along regions containing many grains was experimentally determined and compared with simulated results that were based on the angular dependence of the 'single grain' SAW velocity within single grains and the grain orientation distribution. The polycrystalline SAW velocities turn out to vary with texture. The SAW velocities and their angular variations for {110} texture were found to be larger than that the ones for {111} texture or the strong γ fiber texture. The SAW velocities for {001} texture were larger than for {111} texture, but with almost the same angular dependence. The results infer the feasibility to apply angular SAW angular dispersion measurements by laser ultrasonics for on-line texture monitoring.

Investigation of synthetic spider silk crystallinity and alignment via electrothermal, pyroelectric, literature XRD, and tensile techniques.

The processes used to create synthetic spider silk greatly affect the properties of the produced fibers. This paper investigates the effect of process variations during artificial spinning on the thermal and mechanical properties of the produced silk. Property values are also compared to the ones of the natural dragline silk of the N. clavipes spider, and to unprocessed (as-spun) synthetic silk. Structural characterization by scanning pyroelectric microscopy is employed to provide insight into the axial orientation of the crystalline regions of the fiber and is supported by XRD data. The results show that stretching and passage through liquid baths induce crystal formation and axial alignment in synthetic fibers, but with different structural organization than natural silks. Furthermore, an increase in thermal diffusivity and elastic modulus is observed with decreasing fiber diameter, trending towards properties of natural fiber. This effect seems to be related to silk fibers being subjected to a radial gradient during production.

Homogeneous liquid-liquid extraction of metal ions with non-fluorinated bis(2-ethylhexyl)phosphate ionic liquids having a lower critical solution temperature in combination with water.

Ionic liquids with an ether-functionalised cation and the bis(2-ethylhexyl)phosphate anion show thermomorphic behaviour in water, with a lower critical solution temperature. These ionic liquids are useful for homogeneous liquid-liquid extraction of first-row (3d) transition metals.

Imaging of transient surface acoustic waves by full-field photorefractive interferometry.

A stroboscopic full-field imaging technique based on photorefractive interferometry for the visualization of rapidly changing surface displacement fields by using of a standard charge-coupled device (CCD) camera is presented. The photorefractive buildup of the space charge field during and after probe laser pulses is simulated numerically. The resulting anisotropic diffraction upon the refractive index grating and the interference between the polarization-rotated diffracted reference beam and the transmitted signal beam are modeled theoretically. The method is experimentally demonstrated by full-field imaging of the propagation of photoacoustically generated surface acoustic waves with a temporal resolution of nanoseconds. The surface acoustic wave propagation in a 23 mm × 17 mm area on an aluminum plate was visualized with 520 × 696 pixels of the CCD sensor, yielding a spatial resolution of 33 µm. The short pulse duration (8 ns) of the probe laser yields the capability of imaging SAWs with frequencies up to 60 MHz.