RESUMEN
This research addresses challenges with silver nanowires (Ag NWs) as transparent conductive electrodes (TCEs) and heaters in commercial devices. Here, zinc oxide nanoparticles (ZnO NPs) are first reported as a protective layer for Ag NWs. Multi-physics simulations confirm enhanced thermal stability due to improved heat dissipation, temperature distribution, and thermal conductivity from ZnO. When Ag NWs are surrounded by air, heat transfers mainly through convection and radiation because of air's low conduction coefficient. Encasing Ag NWs in ZnO enhances heat transfer to the ZnO surface, accelerating cooling and dissipating more heat into the atmosphere via convection. The results show composite's efficiency in the Joule effect, maintaining a consistent temperature of 78 °C for 700 s after 500 bending cycles, a significant improvement over Ag NWs operating for only 5 s at 80 °C. Additionally, the composite film exhibited exceptional performance, including a sheet resistance of 9.8 Ω sq-1 and an optical transmittance of 96.96 %, outperforming Ag NWs, which have a sheet resistance of 12 Ω sq-1 and a transmittance of 94.11%. The combination of enhanced electrical, thermal, and mechanical stability, along with impressive optical properties, makes Ag NWs/ZnO NPs a promising candidate for transparent conductive electrode materials in various applications.
RESUMEN
Plasmonic color printing has received significant attention owing to its advantages such as nonfading and nontoxic color expression, without necessitating the use of chemical dyes. Recently, color generation from laser-induced plasmonic nanostructures has been extensively explored because of its simplicity, cost-effectiveness, and large-scale processability. However, these methods usually utilize a top-down method that causes unexpected background colors. Here, we proposed a novel method of plasmonic color printing via a bottom-up type laser-induced photomodification process. In the proposed method, selective silver nanoparticles (Ag NPs) structure could be fabricated on a transparent substrate through a unique organometallic solution-based laser patterning process. A set of color palettes was formed on the basis of different processing parameters such as laser fluence, scanning speed, and baking time. This color change was verified by finite-difference time-domain (FDTD) simulations via monitoring the spectral peak shift of the localized surface plasmon resonance (LSPR) at Ag NPs. It was also confirmed that the colors can be fabricated at a relatively high scanning speed (≥10 mm/s) on a large substrate (>300 mm2). Since semitransparent color images can be patterned on various transparent substrates, this process will broaden the application range of laser-induced plasmonic color generation.
RESUMEN
The flashlight annealing process has been widely used in the field of flexible and printed electronics because it can instantly induce chemical and structural modifications over a large area on an electronic functional layer in a subsecond time range. In this study, for the first time, we explored a straightforward method to develop strong self-adhesion on a metal nanowire-based flexible and transparent conductive film via flashlight irradiation. Nanowire interlocking, for strong mechanical bonding at the interface between the nanowires and polyamide film, was achieved by simple hot pressing. Then, by irradiating the nanowire-impregnated film with a flashlight, several events such as interdiffusion and melting of surface polymers could be induced along with morphological changes leading to an increase in the film surface area. As a result, the surface of the fabricated film exhibited strong interfacial interactions while forming intimate contact with the heterogeneous surfaces of other objects, thereby becoming strongly self-adhesive. This readily achievable, self-attachable, flexible, and transparent electrode allowed the self-interconnection of a light-emitting diode chip, and it was also compatible for various applications, such as defogging windows and transparent organic light-emitting diodes.
RESUMEN
Development of electronic devices on ultrathin flexible plastic substrates is of great value in terms of portability, cost reduction, and mechanical flexibility. However, because thin plastic substrates with low heat capacity can be more easily damaged by thermal energy, their use is limited. Highly flexible nanowire (NW) transparent conductive electrodes on ultrathin (â¼10 µm) low cost polyethylene terephthalate (PET) substrates are fabricated. The control of intense pulsed light (IPL) irradiation process parameters to induce NW welding for maximum conductivity and minimal thermal damage of the PET substrate is explored. For this purpose, trends in temperature variation of NW thin films irradiated by IPL under various operating conditions are numerically analyzed using commercial software. Simulations indicate that irradiating light operated at a higher voltage and for a shorter time, and use of multiple pulses of low frequency can reduce thermal deformation of the PET substrate. Furthermore, we experimentally confirm that NW transparent electrodes can be successfully fabricated with less thermal deformation of the ultrathin plastic substrate when light is irradiated under well-controlled conditions derived from the simulation. The highly flexible NW transparent conducting electrode exhibits excellent mechanical flexibility to withstand severe deformation and can be successfully implemented in flexible organic light-emitting diodes (OLEDs).
RESUMEN
We develop a facile route to the scalable fabrication of flexible reattachable ionomer nanopatterns (RAINs) by continuous nanoinscribing and low-temperature roll imprinting, which are repeatedly attachable to and detachable from arbitrarily shaped surfaces. First, by sequentially performing continuous nanoinscribing over a polymer substrate along the multiple directions, we readily create the multidimensional nanopattern, which otherwise demands complex nanofabrication. After its transfer to an elastomer pad for use as a soft nanoimprinting stamp, we then conduct a low-temperature roll imprinting of the ionomer film to fabricate a flexible and highly transparent RAIN. Reversible loosening of ionic units in the ionomer material at the mild temperature as low as â¼60-70 °C enables the faithful nanopatterning over thermosensitive organic compounds and fragile materials under a slight pressure. The excellent adhesion purely emerging from ionic interactions uniquely realizes the conformal attachability and clean detachability of RAINs for universal targets in ambient conditions, particularly beneficial for individual wearable and mobile devices requiring the user-specific "on/off" of the nanopattern-driven functionalities. As one vivid example, we demonstrate that a single light-emitting device can be switched from the focused pointer to the widespread flashlight depending on the RAIN application upon user's purpose.
RESUMEN
A simple route to fabricate defect-free Ag-nanoparticle-carbon-nanotube composite-based high-resolution mesh flexible transparent conducting electrodes (FTCEs) is explored. In the selective photonic sintering-based patterning process, a highly soft rubber or thin plastic substrate is utilized to achieve close and uniform contact between the composite layer and photomask, with which uniform light irradiation can be obtained with diminished light diffraction. This well-controlled process results in developing a fine and uniform mesh pattern (≈12 µm). The mesh patternability is confirmed to be dependent on heat distribution in the selectively light-irradiated film and the pattern design for FTCE could be adopted for more precise patterns with desired performance. Moreover, using a very thin substrate could allow the mesh to be positioned closer to the strain-free neutral mechanical plane. Due to strong interfacial adhesion between the mesh pattern and substrate, the mesh FTCE could tolerate severe mechanical deformation without performance degradation. It is demonstrated that a transparent heater with fine mesh patterns on thin substrate can maintain stability after 100 repeated washing test cycles in which a variety of stress situations occurring in combination. The presented highly durable FTCE and simple fabrication processes may be widely adoptable for various flexible, large-area, and wearable optoelectronic devices.