Plasma chemical and chemical functionalization of polystyrene colloidal crystals.

Self-assembling systems of colloidal spheres are widely used as templates for the structured deposition of metals and semiconductors. Multilayer samples of ordered polystyrene spheres are prepared by a flow induced process. The subsequent surface activation by a dielectric barrier discharge in oxygen is followed by the fabrication of protecting polysiloxane layers. Electrochemical deposition of copper is used to test the stability of the pre-treated colloidal crystal. The arrangement of the spheres is preserved during the deposition process, due to the polysiloxane layer. The results of the consecutive preparation steps are investigated concerning topographical and chemical changes by atomic force microscopy, scanning electron microscopy and X-ray photoelectron spectroscopy.

Plasma electrochemistry in ionic liquids: deposition of copper nanoparticles.

We report on the synthesis of copper nanoparticles in two different water- and air-stable ionic liquids using plasma electrochemical deposition. The copper nanoparticles were deposited in 1-butyl-1-methylpyrrolidinium bis(trifluoromethylsulfonyl)amide ([Py(1,4)]Tf(2)N) and 1-ethyl-3-methylimidazolium bis(trifluoromethylsulfonyl)amide ([EMIm]Tf(2)N). To get information on the dimensions of the particles made, we have applied in situ transmission electron microscopy (TEM) (particles in ionic liquid). The chemical composition was investigated by ex situ X-ray photoelectron spectroscopy (XPS). We found that the copper particles produced in [Py(1,4)]Tf(2)N were larger in size compared to the particles obtained in [EMIm] Tf(2)N (roughly 20 vs. 10 nm). The chemical composition of the particle surface differs too. In both cases the particles are partly oxidised leading to a CuO shell, but the particles obtained in [Py(1,4)]Tf(2)N carry a lot of residues from the ionic liquid.

Oxygen incorporation into strontium titanate single crystals from CO(2) dissociation.

Oxygen incorporation from CO(2) into Fe-doped SrTiO(3)(100) single crystals (0.013 at% Fe, 0.039 at% Fe and 0.13 at% Fe) was investigated. Oxygen incorporation processes using (13)C(18)O(2) as the gas source were studied by isotope exchange depth profiling (IEDP) and subsequent secondary-ion mass spectroscopy (SIMS). The interaction of CO(2) with SrTiO(3) (100) surfaces was further studied with different surface analytical techniques like metastable induced electron spectroscopy (MIES), ultraviolet photoelectron spectroscopy (UPS) and X-ray photoelectron spectroscopy (XPS). Results indicate that CO(2) interaction with SrTiO(3) (100) surfaces does not change the surface at all. It seems that CO(2) provides a very low sticking probability on the surface as it is not traced by valence band spectroscopy even at room temperature. Nonetheless, (13)C(18)O(2) acts as an incorporation source of (18)O into the Fe-doped SrTiO(3) single crystals. The diffusion coefficient exhibits a peculiar behaviour when Fe concentration increases. No carbon incorporation is observed at all.

Nanostructures on La-doped SrTiO3 surfaces.

SrTiO(3)(100) single crystals with high donor dopant concentrations (5 at% La) were annealed at 1000 degrees C for up to 150 h in ultrahigh vacuum (UHV). By applying scanning tunneling microscopy (STM) nanostructures are observed on top of the surface with typical diameters of 20 nm and typical heights of 8 nm. To characterize their electronic structure and chemical composition, the surface was analyzed by metastable impact electron spectroscopy (MIES), ultraviolet photoelectron spectroscopy (UPS), scanning tunneling spectroscopy (STS), and depth profiling Auger electron spectroscopy (AES). Investigations of the stoichiometry suggest that the secondary phases consist of LaTiO(3). We present a defect chemistry model which attempts to explain the observed effects.