Effect of polymerization cycles on the linear dimensional change, hardness and impact strength of denture base acrylic resins.

AIM: This study verified the effect of polymerizing cycles on the linear dimensional change, hardness and impact strength of denture acrylic resins. METHODS: One hundred and twenty samples (N.=10) each for the Classico and Vipi acrylic resins were made according to the manufacturers' instructions. The polymerization cycles were: 1- water bath at 74 ºC for 9 hr; 2- water bath at 74ºC for 8 hr and temperature increased to 100 ºC for 1 hr; 3- water bath at 74 ºC for 2 hr and temperature increased to 100 ºC for 1 hr; and 4- water bath at 120ºC and 60 pounds pressure for 1 hr. Samples were deflasked after flask cooling and submitted to finishing. Linear distances between referential points in the samples were measured at deflasking and after water storage for 7 and 30 days with a comparator microscope with an accuracy of 0.0005 mm. Knoop hardness test was accomplished in a durometer with a load of 25 gf for 10 sec and an average of three indentations was considered for the sample hardness. Impact strength (kgf/cm²) was measured by the Charpy system with load of 40 kpcm. Data were submitted to ANOVA and Tukey's test (5%). RESULTS: Dimensional changes in the A-B and A-C distances, hardness values and impact strength for Classico and Vipi resins were differently influenced by the polymerization cycles, when deflasking and water storage for 7 and 30 days were considered. CONCLUSION: Linear dimensional change, hardness and impact strength of denture acrylic resins were differently affected by the polymerization cycles.

Effects of laser-weld joint opening size on fatigue strength of Ti-6Al-4V structures with several diameters.

This study was conducted to evaluate the fatigue strength of Ti-6Al-4V laser-welded joints with several diameters and joint openings. Sixty dumbbell rods were machined in Ti-6Al-4V alloy with central diameters of 1·5, 2·0 and 3·5 mm. The specimens were sectioned and then welded using two joint openings (0·0 and 0·6 mm). The combination of variables created six groups, which when added to the intact groups made a total of nine groups (n = 10). Laser welding was executed as follows: 360 V per 8 ms (1·5 and 2·0 mm) and 380 V per 9 ms (3·5 mm) with focus and frequency regulated to zero. The joints were finished, polished and submitted to radiographic examination to be analysed visually for the presence of porosity. The specimens were then subjected to a mechanical cyclic test, and the number of cycles until failure was recorded. The fracture surface was examined with a scanning electron microscope (SEM). The Kruskal-Wallis test and Dunn test (α = 0·05) indicated that the number of cycles required for fracture was lower for all specimens with joint openings of 0·6 mm, and for 3·5-mm-diameter specimens with joint openings of 0·0 mm. The Spearman correlation coefficient (α = 0·05) indicated that there was a negative correlation between the number of cycles and the presence of porosity. So, laser welding of Ti-6Al-4V structures with a thin diameter provides the best conditions for the juxtaposition of parts. Radiographic examination allows for the detection of internal voids in titanium joints.

Passive fit of frameworks in titanium and palladium-silver alloy submitted the laser welding.

This study evaluated the precision of fit of implant frameworks cast in titanium (cp Ti) and palladium-silver alloy (Pd-Ag), made by the one-piece cast and laser welding techniques. From a metal matrix with five implants, 20 master casts were obtained, to which replicas of implants were incorporated. On these masters 10 frameworks were made for each type of material (cp Ti and Pd-Ag alloy). Half of these were made by the one-piece cast technique and the other half by the laser welding technique. The implant/prosthesis interface was analysed and measured in the vestibular and lingual regions of the central and distal implants with the help of a measuring microscope. The results indicated that in the central cylinders, the Tukey test (P<0.0005) showed a significant difference in the passive fit between the laser-welded frameworks (34.73 microm) and those one-piece cast frameworks (151.39 microm), and as regards materials, the palladium-silver alloy (66.30 microm) showed better results than the titanium (119.83 microm). In the distal cylinders there was no significant difference between the frameworks cast in titanium and palladium-silver by the one-piece technique. However, after laser welding, there was a significant difference for the frameworks cast in titanium (31.37 microm) and palladium-silver (106.59 microm).

Surface roughness of acrylic resins submitted to mechanical and chemical polishing.

Surface roughness is extremely important as it influences micro-organism accumulation and consequently oral health. The aim of the present study was to evaluate the influence of mechanical polishing (MP) and chemical polishing (CP) on surface roughness of four heat-cured denture base acrylic resins. Twenty sample discs were prepared for each of the following acrylic resins: Classico (CL), QC 20 (QC), Acron MC (AC) and Onda Cryl (ON). The first two are boiling cured resins and the latter two are microwave cured. After curing and deflasking, samples were ground and subdivided into two groups: MP, which received pumice slurry, chalk powder, soft brush and felt cone, at a bench vice; and CP, which received fluid specifically for chemical polisher. Surface roughness was measured using a Surf Corder SE 1700 rugosimeter. Data collected were statistically analysed by analysis of variance followed by Tukey's test. Surface roughness means in mum were: CL-MP: 0.0350; CL-CP: 0.2298; QC-MP: 0.0307; QC-CP: 0.1792; AC-MP: 0.0312; AC-CP: 0.2700; ON-MP: 0.0321; ON-CP: 0.2949. It can be concluded that MP produced significantly smoother surfaces than CP and that surface roughness because of MP was not influenced by acrylic resin type, whereas this was not true of CP.

Influence of adhesive systems on the bonding of dental amalgam to glass ionomer cement.

STATEMENT OF PROBLEM: Dental amalgam restorations have traditionally been retained in cavity preparations by surgical procedures called retention form. In this procedure healthy dental structure is usually removed to create adequate retention. The increasing use of bonding systems for restorative procedures may result in more conservative cavity preparations. PURPOSE: The purpose of this study was to evaluate the tensile bond strength of the amalgam to glass ionomer cement under the influence of three adhesive systems (Panavia-EX, Vidrion F fresh mix, and Alpha Seal). MATERIAL AND METHODS: The bonded assemblies were stored in an environment of 100% relative humidity and 37 degrees C for 24-hour and 30-day storage periods. The test specimen was loaded in tension to failure on a universal testing machine with a crosshead speed of 6 mm/min. RESULTS: The results revealed that in the 24-hour period without acid etch fresh Vidrion F and Panavia Ex adhesives were stronger than autopolymerizing sealant. Panavia Ex adhesive was stronger in the 24-hour period with acid etch. CONCLUSIONS: The 30-day period with acid etch revealed no statistical difference among the adhesives. In the 30-day period without acid etch, the fresh Vidrion F adhesive recorded the greatest tensile bond strength.