RESUMEN
Numerical simulations of D y 3+-doped aluminosilicate fiber lasers for yellow light emission are presented. The 4 F 9/2â6 H 13/2 laser transition emitting at approximately 580 nm has been developed experimentally with 445 nm diode pumping and shows promise for higher output power in both silicate and in particular fluoride glass hosts. In this report, we focus on accumulating the published spectroscopic data in order to quantify cross relaxation (CR) in each of these hosts and use it to estimate its role in the laser dynamics. The model involves calculation of the branching ratios, and radiative and nonradiative decay rates and compares well with reported experimental results. We show the important role of the background losses on previous laser performance and the relatively strong increase in the laser threshold as a result of CR despite the moderately low D y 3+ concentrations that have been experimentally tested.
RESUMEN
We report the high-efficiency operation of a 3.05 µm dysprosium-doped fluoroindate glass fiber laser that is in-band pumped at 2.83 µm using an erbium-doped fluorozirconate glass fiber laser. The demonstrated slope efficiency of the free-running laser of 82% represents approximately 90% of the Stokes efficiency limit; a maximum output power of 0.36 W, the highest for a fluoroindate glass fiber laser, was recorded. Narrow-linewidth wavelength stabilization at 3.2 µm was achieved by utilizing a first-reported, to the best of our knowledge, high-reflectivity fiber Bragg grating inscribed in the Dy3+-doped fluoroindate glass. These results lay the foundation for future power-scaling of mid-infrared fiber lasers using fluoroindate glass.
RESUMEN
For the first time, to the best of the authors' knowledge, a cladding-pumped bismuth-doped fiber laser (BDFL) is demonstrated. A "home-made" Bi-doped germanosilicate fiber with a 125 µm circular outer cladding made of fused silica and coated by a low refractive index polymer is used as an active medium pumped by commercial multimode laser diodes with a total output power of 25 W at 808 nm. We find that the BDFL with a free-running cavity (when feedback is provided by ≈4% back reflection from two bare right-angle cleaved fiber ends) composed of a 100-m-long bismuth-doped fiber is capable of emitting at a wavelength of 1440 nm. A slope efficiency of 0.5% with respect to the absorbed pump power with a maximum output power of ≈50 mW is obtained in a BDFL with a cavity formed by a highly reflective Bragg grating at 1461 nm and a right-angle cleaved fiber end. The beam quality factors (M2) of the output BDFL in the horizontal and vertical directions are measured to be 1.18 and 1.13, respectively. The processes affecting the efficiency of the BDFLs are also discussed. The possible improvements for the output power scaling and increasing the efficiency of the cladding-pumped BDFLs are proposed.
RESUMEN
During last decades there has been considerable interest in developing a fiber amplifier for the 1.3-[Formula: see text]m spectral region that is comparable in performance to the Er-doped fiber amplifier operating near 1.55 [Formula: see text]m. It is due to the fact that most of the existing fiber-optic communication systems that dominate terrestrial networks could be used for the data transmission in O-band (1260-1360 nm), where dispersion compensation is not required, providing a low-cost increase of the capacity. In this regard, significant efforts of the research laboratories were initially directed towards the study of the praseodymium-doped fluoride fiber amplifier having high gain and output powers at the desired wavelengths. However, despite the fact that this type of amplifiers had rapidly appeared as a commercial amplifier prototype it did not receive widespread demand in the telecom industry because of its low efficiency. It stimulated the search of novel optical materials for this purpose. About 10 years ago, a new type of bismuth-doped active fibers was developed, which turned out to be a promising medium for amplification at 1.3 [Formula: see text]m. Here, we report on the development of a compact and efficient 20-dB (achieved for signal powers between [Formula: see text] and [Formula: see text] dBm) bismuth-doped fiber amplifier for a wavelength region of 1300-1350 nm in the forward, backward and bi-directional configurations, which can be pumped by a commercially available laser diode at 1230 nm with an output power of 250 mW. The compactness of the tested amplifier was provided by using a depressed cladding active fiber with low bending loss, which was coiled on a reel with a radius of 1.5 cm. We studied the gain and noise figure characteristics at different pump and signal powers. A record gain coefficient of 0.18 dB/mW (at the pump-to-signal power conversion efficiency of above 27[Formula: see text]) has been achieved.
RESUMEN
For the first time, we report on the fabrication of a bend-insensitive single-mode bismuth (Bi)-doped $ {{\rm P}_2}{{\rm O}_5} {-} {{\rm SiO}_2} $P2O5-SiO2 fiber having a depressed cladding design and study its gain characteristics at a spectral region of 1.3-1.4 µm. It was shown that the obtained Bi-doped fiber can efficiently operate in the spectral band even at a bend radius of 1.5 cm. In addition, it was shown that this type of fiber has a smaller mode-field diameter in comparison with a step-index single-mode Bi-doped $ {{\rm P}_2}{{\rm O}_5} {-} {{\rm SiO}_2} $P2O5-SiO2 fiber with $ \Delta {n} \approx 0.006 $Δn≈0.006 that resulted in a decrease of saturation power and, as a consequence, in a reduction of the total pump power required to a high-level-gain operation. The laser and gain experiments show the possibility of the construction of a compact high-performance optical amplifier for O-band based on the depressed-cladding Bi-doped fiber.