A knotless bidirectional-barbed tendon repair is inferior to conventional 4-strand repairs in cyclic loading.

UNLABELLED: We divided 21 flexor digitorum profundus tendons in the index, middle and ring fingers in seven cadaver hands into three groups. The tendons were cut in zone 2 and repaired using a 4-strand cruciate core suture repair with one of the following three materials in each group: (1) a knotless repair with a 2-0 bidirectional-barbed suture, which has similar tensile strength as a 4-0 non-barbed suture used in the other two groups; (2) a knotted locking repair with a non-barbed 4-0 conventional suture; and (3) a non-locking repair with a non-barbed 4-0 knotless suture. The repaired fingers were cyclically loaded through a simulated active range of motion to a 5 N load. We monitored and recorded the gap sizes at regular intervals during the test. The 2-0 bidirectional-barbed suture group and non-barbed suture groups developed gaps of 2.2 mm after 10 cycles and 2.4 mm after 20 cycles, respectively. Over 1000 cycles, the mean gaps were 3.2 mm in the 4-0 conventional suture group and 9.1 mm in the 2-0 bidirectional-barbed group. The tendons in the 2-0 bidirectional-barbed group gapped earlier, with statistically significant differences compared with those in the locking repair with a non-barbed 4-0 knotless suture group. The repair strength of the barbed suture technique was inferior to the cruciate repairs using a conventional 4-0 non-barbed suture tested in this cyclic-loading model. LEVEL OF EVIDENCE: Level V.

Tibiotalocalcaneal arthrodesis: a biomechanical analysis of the rotational stability of the Biomet Ankle Arthrodesis Nail.

We hypothesized that the posterior-to-anterior (PA) calcaneal interlocking screw of the Biomet Ankle Arthrodesis Nail would increase rotational stability secondary to increased bone purchase compared with the standard lateral-to-medial (transverse) screw. Each of 10 fresh human cadaver lower limbs (five matched pairs) were stabilized with a nail inserted retrograde through the calcaneus, talus, and tibia according to standard technique. One limb of each pair was fixed with a transverse calcaneal screw; the contralateral limb, with a PA calcaneal screw. Each limb was then subjected to torsional testing on an MTS Mini Bionix load frame. The PA screw construct was significantly stiffer than the transverse screw construct: 1.96 and 1.41 Nm/E, respectively (P < 0.036).

The contribution of the medial calcaneal osteotomy to the correction of flatfoot deformities.

HYPOTHESES/PURPOSE: The success of the medial displacement calcaneal osteotomy in correcting flatfoot deformities is likely to be the result of a shift of the Achilles tendon forces on the hindfoot. The purpose of this study was twofold: 1) to define the contribution of the Achilles tendon to the flatfoot deformity, and 2) to define the effect of a calcaneal medial displacement osteotomy. METHODS: We used six different experimental dynamic stages: 1) intact foot without Achilles loading; 2) intact foot with Achilles loading; 3) flatfoot without medial calcaneal displacement osteotomy and without Achilles loading; 4) flatfoot without medial calcaneal displacement osteotomy but with Achilles loading; 5) flatfoot with medial calcaneal displacement osteotomy but without Achilles loading; and 6) flatfoot with medial calcaneal displacement osteotomy and with Achilles loading. The experimental flaffoot was developed by releasing the posterior tibial tendon, spring ligament, and plantar fascia and applying 7,000 cycles of axial fatigue load (range, 700 to 1,400 N; 1-Hz frequency). To simulate the phase of midstance, the peroneus longus, peroneus brevis, flexor digitorum longus, and flexor hallucis longus tendons were grasped by clamps, connected to pneumatic actuators, and loaded with precalculated forces. Anteroposterior and lateral radiographs were obtained for each stage on which the following measurements were made: talonavicular coverage angle, talar-first metatarsal angle, talocalcaneal angle, and height of the medial cuneiform. These measurements were compared with a one-way ANOVA. RESULTS: Between stages 1 and 2, all measurements were statistically insignificant. Between stages 3 and 4, for all measurements, Achilles tendon loading aggravated the flatfoot deformity (p < 0.05). After medial calcaneal osteotomy (stages 5 and 6), the Achilles tendon contributed less to the arch-flattening. We found that the medial displacement osteotomy plays an important role in reducing and/or delaying the progress of flatfoot deformity. CONCLUSIONS/SIGNIFICANCE: In the flatfoot, loading of the Achilles tendon increases the deformity. Medial calcaneal osteotomy significantly decreases the arch-flattening effect of this tendon and therefore limits the potential increase of the deformity.

Cyclic loading of rotator cuff repairs: A comparison of bioabsorbable tacks with metal suture anchors and transosseous sutures.

PURPOSE: The purposes of the study were (1) to compare rotator cuff repair strengths after cyclic loading of 2 bioabsorbable nonsuture-based tack-type anchors, transosseous sutures, and a metal suture-based anchor, and (2) to correlate bone mineral density with mode of failure and cycles to failure. We hypothesized that specimens with a lower bone density would fail through bone at a lower number of cycles independent of the method of cuff fixation. TYPE OF STUDY: Ex vivo biomechanical study. METHODS: Standardized full-thickness rotator cuff defects were created in 30 fresh-frozen cadaveric shoulders that were randomized to 1 of 4 repair groups: transosseous sutures; Mitek Super suture anchors (Mitek Surgical Products, Westwood, MA); smooth bioabsorbable 8-mm Suretacs (Acufex, Smith & Nephew Endoscopy, Mansfield, MA); or spiked bioabsorbable 8-mm Suretacs (Acufex). All repairs were cyclically loaded from 10 to 180 N; the numbers of cycles to 50% (gap, 5 mm) and 100% (gap, 10 mm) failure were recorded. RESULTS: In comparing the repair groups, we found only 1 significant difference: the number of cycles to 100% failure was significantly higher (P <.05) for the smooth bioabsorbable tack than for the transosseous suture group. There were no statistically significant (P

Biomechanical evaluation of the ability of casts and braces to immobilize the ankle and hindfoot.

We evaluated the ability of seven devices to immobilize a prosthetic ankle-foot complex against plantarflexion, dorsiflexion, inversion, and eversion forces: two casts (plaster of Paris and Fiberglas) and five removable braces (molded ankle/foot orthosis, composite boot brace, pneumatic boot walker, nonarticulating fracture boot, and ankle stirrup). Each device was applied to a prosthetic ankle-foot complex and evaluated on a test frame for resistance to sagittal motion and coronal torque. Results showed that casts offered significantly (P < or = 0.05) more resistance to motion in all directions tested than did the braces. The resistance offered by the devices tested depends on the conformity of the device to the shape of the foot in that plane and the material properties of the device. Braces offer the advantage of being easily removed and reapplied. Different braces offer specific advantages and disadvantages in different planes tested, and immobilization selection should be individualized based on this information.

Experimental flatfoot model: the contribution of dynamic loading.

The goal of this study was to determine if the application of muscle forces (simulating the dynamic phase of the midstance part of gait) had an effect on flatfoot deformity. We created a flatfoot model in each of seven cadaver foot specimens by grasping the Achilles, peroneus longus, peroneus brevis, flexor digitorum longus, and flexor hallucis longus tendons with soft-tissue vice clamps connected via wire cables to pneumatic cylinders. The experiment included four stages: 1) initial static axial loading; 2) axial loading after 3,000 load cycles (average, 735 N; range, 70 to 1400 N); 3) axial loading after releasing the spring ligament and plantar fascia; and 4) axial loading after an additional 3,000 load cycles. At each stage, both static (with axial loading only) and dynamic (axial loading with tensioning of the tendons to simulate the muscle forces at midstance) conditions were evaluated radiographically. No change was observed between the static and dynamic conditions in the first two phases of the experiment. After the third phase, changes in the talar-first metatarsal angle and the height of the medial cuneiform were noted, particularly in the dynamic condition. These and additional radiographic changes were magnified in the fourth phase, but only in the dynamic condition. We concluded that, to create an effective flatfoot model, the medial structures, including the spring ligament and possibly the plantar fascia, must be severed. Cyclic loading of the foot further increased the arch flattening, and this effect was magnified by dynamic loading.

Dorsiflexion contracture after the Weil osteotomy: results of cadaver study and three-dimensional analysis.

For metatarsalgia caused by a dislocated lesser metatarsophalangeal (MTP) joint and isolated over-long lesser metatarsals, surgical treatment options without sacrificing the joint are limited. Recently, the Weil osteotomy has been advocated for the treatment of this deformity. In our experience, preliminary results with this technique have revealed a high rate of dorsiflexion contracture of the MTP joints at follow-up. We performed a cadaver study and a three-dimensional analysis on sawbones to investigate this phenomenon. In the cadaveric portion of this study, the second MTP joints of two fresh-frozen cadavers were dissected; the entire ray, with the metatarsal shaft, MTP joint, toe, and plantar fascia, was removed en bloc. After gross anatomic structures were photographed, a Weil osteotomy was performed at 25 degrees relative to the long axis of the metatarsal shaft. The positions of muscles, ligaments, and tendons were noted and photographed before and after the osteotomy. In the sawbones portion of this study, a Weil osteotomy was performed at four different angles (25 degrees, 30 degrees, 35 degrees, and 40 degrees) relative to the long axis of the metatarsal. To ensure reproducibility, the sawbone models were fixed proximally to a vertical milling machine with the second metatarsals inclined 15 degrees to simulate the anatomic position. After making the cut, the plantar fragment was translated along the dorsal fragment proximally for a distance of 5 mm. Before and after the osteotomy, selected x, y, and z coordinates were obtained using a Microscribe 3D digitizer. Data analysis was performed with Microsoft Excel, and ANOVA was used to determine significant differences (p < 0.05) between the various osteotomies. Analysis of the cadaver dissection revealed that after the Weil osteotomy, the tendons of the interosseous muscles move dorsally with respect to the axis of the MTP joint due to the depression of the plantar fragment of the metatarsal. The loss of their flexion effect on the joint permits the pull of the extensor to dorsiflex the toe. The size of the depression for the various osteotomies averaged: 25 degrees osteotomy, 3.03 mm (range, 1.8 to 3.8 mm); 30 degrees osteotomy, 3.2 mm (range, 1.9 to 4.0 mm); 35 degrees osteotomy, 3.5 mm (range, 1.7 to 5.7 mm); and 40 degrees osteotomy, 4.2 mm (range, 2.8 to 6.4 mm). Amounts of shortening relative to the long axis of the metatarsal for the various osteotomies averaged: 25 degrees osteotomy, 5.03 mm (range, 4.77 to 5.30 mm); 30 degrees osteotomy, 4.59 mm (range, 3.47 to 5.19 mm); 35 degrees osteotomy, 4.27 mm (range, 2.87 to 5.00 mm); and 40 degrees osteotomy, 3.65 mm (range, 3.20 to 4.31 mm). According to our analysis, depression of the plantar fragment always occurs after a Weil osteotomy. This depression changes the center of rotation of the MTP joint, and the interosseous muscles then act more as dorsiflexors than as plantarfexors.

Six first metatarsal shaft osteotomies: mechanical and immobilization comparisons.

Because malunion (usually with dorsal elevation of the first metatarsal) has been reported after the treatment of severe hallux valgus deformities by proximal osteotomies, the current study was designed to compare the sagittal stability of six different metatarsal shaft osteotomies: the proximal crescentic, proximal chevron, Mau, Scarf, Ludloff, and biplanar closing wedge osteotomies. A plate was used in the biplanar closing wedge osteotomy; all others used screws for fixation. Ten fresh-frozen, human anatomic lower extremity specimens were used for each osteotomy. Failure loads were measured as units of force (newtons) and converted to pressure (kilopascals). Then the F-Scan system, which uses a thin insole to measure plantar pressure, was used to evaluate the pressure under the first metatarsal of seven volunteers using four types of shoes. According to the results, in patients with normal bone stock who are compliant, any of the four shoe types tested may be used after a Ludloff, Scarf, biplanar wedge (plantar screw fixation), or Mau osteotomy, but the wedge-based shoe should be used after a proximal crescentic or chevron osteotomy or for patients with severe osteopenic bone.

Fixation of patella fractures with braided polyester suture: a biomechanical study.

We tested the quality of fixation of displaced transverse patella fractures using braided polyester suture to investigate the suitability of this material as an alternative to stainless steel wire for fixation of these fractures. Osteotomies were created to simulate fractures of the patella in ten cadaveric knee specimens and were sequentially fixed using two techniques: the modified tension-band technique and the longitudinal anterior band (Lotke) technique. Each technique was implemented using either 1.25-mm stainless steel wire or 7-metric braided polyester suture (No. 5 Ethibond). The quality of fixation for each technique was tested by measuring the fracture gap during three simulated extensions of the knee against gravity on a materials testing machine. All techniques behaved comparably under the loading conditions used. In the four groups, there was no fixation failure (fracture gap > 3 mm) nor any significant difference between the mean maximum fracture gaps. The quality of fixation for braided polyester suture was comparable to that of stainless steel wire for such fractures, providing sufficient stability to withstand loads likely to be encountered during postoperative rehabilitation. Our results support the use of braided polyester suture as an alternative to stainless steel wire for fixation of displaced patella fractures.

Compression arthrodesis of the ankle by triangular external fixation: biomechanical and clinical evaluation.

This article describes a technique of ankle arthrodesis using a triangular external fixation frame and presents the results of biomechanical analysis and clinical experience with the frame. Clinical evaluation of 23 ankle arthrodeses performed using a triangular external fixation frame yielded a 91.3% fusion rate at an average of 11 weeks postfusion. The triangular frame was 79% stiffer than a compression-only external frame in torsion and 39% stiffer in anteroposterior bending. This high rate of fusion is attributed to the elimination of micromotion at the fusion site because of the increased rigidity of the triangular external compression frame.