Hydrochars derived from real organic wastes as carbonaceous precursors of activated carbons for the removal of NO from contaminated gas streams.

The improvement of air quality in densely-populated urban regions constitutes an environmental challenge of increasing concern. In this respect, the abatement of NO emissions, primarily emanating from combustion processes associated with motor-vehicles, along with industrial/domestic combustion systems, represents one of the main problems. Here, three hydrochars from diverse organic residues were used as activated carbon precursors for their evaluation in the NO removal in two potential application scenarios. Hydrochars were physically activated at 800 °C with pure-CO2 or diluted-O2. These materials were tested in a lab-scale biofilter at different conditions (NO concentration, temperature, relative humidity, NO-containing gas and carbon particle size) and in a larger-scale biofilter to evaluate the long-term NO removal capacity. Hydrochar-derived carbons present a relatively well-developed micro- and mesoporous structure, with BET areas of up to 421 m2/g, and a variety of oxygen surface functionalities (carboxylic, lactone, carbonyl and quinone groups), especially concerning CO2-activated carbons. These exhibited an excellent behaviour at low NO concentration (5 ppmv) between 25 and 75 °C with removal capacities of ≈97 % and > 82 %, respectively; and still good-performance (≈66 %) in a more concentrated gas (120 ppmv). Whilst, carbons obtained by diluted-O2 activation from the same hydrochars, evidenced a higher removal capacity loss at high NO concentration. The O2 presence in the gas stream was confirmed as a crucial factor in the NO elimination, since both co-adsorb on the carbon surface favouring NO oxidation to NO2. Besides, the humidity in the airstream diminished the NO removal capacity from 0.88 to 0.51 mgNO/gcarbon, but still remained at 0.54 mgNO/gcarbon, when the carbon (in pellet) was operated at larger-scale biofilter in 9-fold longer test under humid air. Therefore, this study highlights the potential of renewable carbons to serve as cost-effective component in urban biofilters, to mitigate NO emissions from exhaust gases in biomass boilers and urban semi-close areas.

Scaling-Up Microwave-Assisted Synthesis of Highly Defective Pd@UiO-66-NH2 Catalysts for Selective Olefin Hydrogenation under Ambient Conditions.

The need to develop green and cost-effective industrial catalytic processes has led to growing interest in preparing more robust, efficient, and selective heterogeneous catalysts at a large scale. In this regard, microwave-assisted synthesis is a fast method for fabricating heterogeneous catalysts (including metal oxides, zeolites, metal-organic frameworks, and supported metal nanoparticles) with enhanced catalytic properties, enabling synthesis scale-up. Herein, the synthesis of nanosized UiO-66-NH2 was optimized via a microwave-assisted hydrothermal method to obtain defective matrices essential for the stabilization of metal nanoparticles, promoting catalytically active sites for hydrogenation reactions (760 kg·m-3·day-1 space time yield, STY). Then, this protocol was scaled up in a multimodal microwave reactor, reaching 86% yield (ca. 1 g, 1450 kg·m-3·day-1 STY) in only 30 min. Afterward, Pd nanoparticles were formed in situ decorating the nanoMOF by an effective and fast microwave-assisted hydrothermal method, resulting in the formation of Pd@UiO-66-NH2 composites. Both the localization and oxidation states of Pd nanoparticles (NPs) in the MOF were achieved using high-angle annular dark-field scanning transmission electron microscopy (HAADF-STEM) and X-ray photoelectron spectroscopy (XPS), respectively. The optimal composite, loaded with 1.7 wt % Pd, exhibited an extraordinary catalytic activity (>95% yield, 100% selectivity) under mild conditions (1 bar H2, 25 °C, 1 h reaction time), not only in the selective hydrogenation of a variety of single alkenes (1-hexene, 1-octene, 1-tridecene, cyclohexene, and tetraphenyl ethylene) but also in the conversion of a complex mixture of alkenes (i.e., 1-hexene, 1-tridecene, and anethole). The results showed a powerful interaction and synergy between the active phase (Pd NPs) and the catalytic porous scaffold (UiO-66-NH2), which are essential for the selectivity and recyclability.

An electroencephalogram microdisplay to visualize neuronal activity on the brain surface.

Functional mapping during brain surgery is applied to define brain areas that control critical functions and cannot be removed. Currently, these procedures rely on verbal interactions between the neurosurgeon and electrophysiologist, which can be time-consuming. In addition, the electrode grids that are used to measure brain activity and to identify the boundaries of pathological versus functional brain regions have low resolution and limited conformity to the brain surface. Here, we present the development of an intracranial electroencephalogram (iEEG)-microdisplay that consists of freestanding arrays of 2048 GaN light-emitting diodes laminated on the back of micro-electrocorticography electrode grids. With a series of proof-of-concept experiments in rats and pigs, we demonstrate that these iEEG-microdisplays allowed us to perform real-time iEEG recordings and display cortical activities by spatially corresponding light patterns on the surface of the brain in the surgical field. Furthermore, iEEG-microdisplays allowed us to identify and display cortical landmarks and pathological activities from rat and pig models. Using a dual-color iEEG-microdisplay, we demonstrated coregistration of the functional cortical boundaries with one color and displayed the evolution of electrical potentials associated with epileptiform activity with another color. The iEEG-microdisplay holds promise to facilitate monitoring of pathological brain activity in clinical settings.

Simultaneous removal of brominated and chlorinated species during the production of oils by e-waste plastics catalytic hydropyrolysis.

The production of added-value chemicals via pyrolysis of plastic wastes, such as those from electrical and electronic equipment (WEEE), needs addressing their usual contamination with halogens (mainly Br and Cl). This work compares the conversion via pyrolysis and hydropyrolysis of a real WEEE plastic, having a complex composition, in two different reactor configurations: down-flow (DF) and up-flow (UF). Likewise, the effects of incorporating a Pd/Al2O3 catalyst and using two different pressures (1 and 6 bar) have been assessed. With the DF mode, pyrolysis at 1 bar leads to an oil yield above 80 wt% and a total halogen content of about 600 ppm (vs 1600 ppm in the water-washed WEEE plastic). Under DF catalytic hydropyrolysis at 6 bar, this high oil yield is maintained while its dehalogenation degree is improved (142 ppm). Operating with the up-flow configuration, under 6 bar and H2 presence, leads to some reduction in the oil yield (about 70 wt%) but significantly decreases the oil halogen content (55 ppm Cl and total elimination of Br). These results have been related to the slower pyrolysis and longer residence time in the thermal zone of the UF configuration, which favours the halogen-trapping effect of the char fraction, and the pressure-enhanced hydrodehalogenation activity of the catalyst. This study highlights the environmental benefits of the proposed process, emphasizing the lower halogen content in the resulting oils and promoting a more sustainable approach to plastic waste valorisation.

The Brain Electroencephalogram Microdisplay for Precision Neurosurgery.

Brain surgeries are among the most delicate clinical procedures and must be performed with the most technologically robust and advanced tools. When such surgical procedures are performed in functionally critical regions of the brain, functional mapping is applied as a standard practice that involves direct coordinated interactions between the neurosurgeon and the clinical neurology electrophysiology team. However, information flow during these interactions is commonly verbal as well as time consuming which in turn increases the duration and cost of the surgery, possibly compromising the patient outcomes. Additionally, the grids that measure brain activity and identify the boundaries of pathological versus functional brain regions suffer from low resolution (3-10 mm contact to contact spacing) with limited conformity to the brain surface. Here, we introduce a brain intracranial electroencephalogram microdisplay (Brain-iEEG-microdisplay) which conforms to the brain to measure the brain activity and display changes in near real-time (40 Hz refresh rate) on the surface of the brain in the surgical field. We used scalable engineered gallium nitride (GaN) substrates with 6" diameter to fabricate, encapsulate, and release free-standing arrays of up to 2048 GaN light emitting diodes (µLEDs) in polyimide substrates. We then laminated the µLED arrays on the back of micro-electrocorticography (µECoG) platinum nanorod grids (PtNRGrids) and developed hardware and software to perform near real-time intracranial EEG analysis and activation of light patterns that correspond to specific cortical activities. Using the Brain-iEEG-microdisplay, we precisely ideFSntified and displayed important cortical landmarks and pharmacologically induced pathological activities. In the rat model, we identified and displayed individual cortical columns corresponding to individual whiskers and the near real-time evolution of epileptic discharges. In the pig animal model, we demonstrated near real-time mapping and display of cortical functional boundaries using somatosensory evoked potentials (SSEP) and display of responses to direct electrical stimulation (DES) from the surface or within the brain tissue. Using a dual-color Brain-iEEG-microdisplay, we demonstrated co-registration of the functional cortical boundaries with one color and displayed the evolution of electrical potentials associated with epileptiform activity with another color. The Brain-iEEG-microdisplay holds the promise of increasing the efficiency of diagnosis and possibly surgical treatment, thereby reducing the cost and improving patient outcomes which would mark a major advancement in neurosurgery. These advances can also be translated to broader applications in neuro-oncology and neurophysiology.

Removal of NO at low concentrations from polluted air in semi-closed environments by activated biochars from renewables feedstocks.

Efficient measures are urgently required in large cities for nitric oxide (NO) elimination from air in urban semi-closed environments (parking lots and tunnels), characterized by low NO concentrations (<10 ppmv) and temperatures. One of the most promising abatement alternatives is the NO oxidation to NO2, which can be further easily captured in an alkali solution or over a porous solid. However, most of the research devoted to this topic is focused on the elimination of NO from fuel exhaust gases, with high NO concentrations (400-2000 ppmv). In this work, sustainable and low-cost activated biochars of different origin and having very different ash contents were employed in NO removal at very low concentrations. Thus, low ash content forestry (oak woodchips, OAK) and high ash content from agriculture (oilseed rape straw, OSR) biochars were subjected to physical activation with CO2 at 900 °C (OAK550-A900CO2 and OSR700-A900CO2, respectively). The NO removal performance tests of such activated carbons were carried out at different experimental conditions: i.e., temperature, relative humidity (0-50 vol% RH), NO-containing gas (N2 or air), amount of activated carbon, and NO concentration, to assess how the activated biochar properties influence their NO removal capacity. The sample OSR700-A900CO2 contained a higher population of oxygen surface functionalities, which might play an important role in the NO removal efficiency in dry conditions since they could assist NO oxidation on carbon active sites when used above room temperature (50-75 °C). However, at room temperature (25 °C), the presence of narrow micropore size distribution at 6 Å became a more relevant property, since it facilitates an intimate contact between NO and O2. Accordingly, the activated biochar from OAK was much more efficient, achieving complete removal of NO from air flow (dry or with 50 vol% RH) at 25 °C during 400 min of testing, making it an ideal candidate as biofilter for purifying air streams of semi-closed spaces contaminated with low concentrations of NO.

Removal of NO at low concentration from air in urban built environments by activated miscanthus biochar.

This work presents an innovative and sustainable approach to remove NO emissions from urban ambient air in confined areas (underground parking areas or tunnels) using low-cost activated carbons obtained from Miscanthus biochar (MSP700) by physical activation (with CO2 or steam) at temperatures ranging from 800 to 900 °C. The NO removal capacity of the activated biochars was evaluated under different conditions (temperature, humidity and oxygen concentration) and compared against a commercial activated carbon. This last material showed a clear dependence on oxygen concentration and temperature, exhibiting a maximum capacity of 72.6% in air at 20 °C, whilst, its capacity notably decreased at higher temperatures, revealing that physical NO adsorption is the limiting step for the commercial sample that presents limited oxygen surface functionalities. In contrast, MSP700-activated biochars reached nearly complete NO removal (99.9%) at all tested temperatures in air ambient. Those MSP700-derived carbons only required low oxygen concentration (4 vol%) in the gas stream to achieve the full NO removal at 20 °C. Moreover, they also showed an excellent performance in the presence of H2O, reaching NO removal higher than 96%. This remarkable activity results from the abundance of basic oxygenated surface groups, which act as active sites for NO/O2 adsorption, along with the presence of a homogeneous microporosity of 6 Å, which enables intimate contact between NO and O2. These features promote the oxidation of NO to NO2, which is further retained over the carbon surface. Therefore, the activated biochars studied here could be considered promising materials for the efficient removal of NO at low concentrations from air at moderate temperatures, thus closely approaching real-life conditions in confined spaces.

Jacaranda oil administration improves serum biomarkers and bioavailability of bioactive conjugated fatty acids, and alters fatty acid profile of mice tissues.

Jacaric acid, a conjugated linolenic acid (CLNA) present in jacaranda oil (JO), is considered a potent anticarcinogenic agent. Several studies have focused on its biological effects, but the metabolism once consumed is not clear yet. The aim of this work was to evaluate the effects of two different daily doses of JO on serum parameters and fatty acid (FA) profile of mice tissues after 4 weeks of feeding. No significant changes on body weight gain, food intake, or tissue weight were determined after 0.7 or 2 ml/kg of JO supplementation compared to control animals. Significantly lower blood low-density lipoproteins-cholesterol (20 mg/dl) and glucose (~147-148 mg/dl) levels were detected in both oil-treated groups compared to control (31.2 and 165 mg/dl, respectively). Moreover, jacaric acid was partially converted into cis9, trans11 conjugated linoleic acid (CLA) and thus further incorporated into tissues. Liver evidenced the highest total conjugated fatty acid content (1.1%-2.2%), followed by epididymal (0.7%-1.9%) and mesenteric (1.4%-1.8%) fat. Lower saturated and higher unsaturated fatty acid content was detected in both oil-treated groups compared to control. Our results support the safety of JO and its potential application with a functional or nutraceutical propose, by increasing human CLNA consumption and further availability of CLA.

Determining the Role of Fe-Doping on Promoting the Thermochemical Energy Storage Performance of (Mn1- x Fex )3 O4 Spinels.

Mn oxides are promising materials for thermochemical heat store, but slow reoxidation of Mn3 O4 to Mn2 O3 limits efficiency. In contrast, (Mn1- x Fex )3 O4 oxides show an enhanced transformation rate, but fundamental understanding of the role played by Fe cations is lacking. Here, nanoscale characterization of Fe-doped Mn oxides is performed to elucidate how Fe incorporation influences solid-state transformations. X-ray diffraction reveals the presence of two distinct spinel phases, cubic jacobsite and tetragonal hausmannite for samples with more than 10% of Fe. Chemical mapping exposes wide variation of Fe content between grains, but an even distribution within crystallites. Due to the similarities of spinels structures, high-resolution scanning transmission electron microscopy cannot discriminate unambiguously between them, but Fe-enriched crystallites likely correspond to jacobsite. In situ X-ray absorption spectroscopy confirms that increasing Fe content up to 20% boosts the reoxidation rate, leading to the transformation of Mn2+  in the spinel phase to Mn3+ in bixbyite. Extended X-ray absorption fine structure shows that FeO length is larger than MnO, but both electron energy loss spectroscopy and X-ray absorption near edge structure indicate that iron is always present as Fe3+  in octahedral sites. These structural modifications may facilitate ionic diffusion during bixbyite formation.

Lipoabdominoplastia em âncora / Anchor lipoabdominoplasty

A obesidade mórbida se caracteriza por acúmulo de tecido adiposo que se distribui de maneira heterogênea em todo o organismo, tendo a gastroplastia como o mais recente método de tratamento cirúrgico. Após perda considerável de peso, o doente apresenta sobras cutâneas, sob essas sobras acumulam-se secreções que favorecem a instalação de infecções cutâneas que podem ser minimizadas com a execução de dermolipectomias. Os autores descrevem a técnica de lipoabdominoplastia em âncora, adaptando os princípios de descolamento reduzido do retalho, lipoaspiração de abdome e flancos, e preservação da fáscia de Scarpa infraumbilical associado à marcação pré-cirúrgica em "Fleur-de-Lis". A técnica foi realizada em 17 pacientes em pós-operatório tardio de gastroplastia, entre janeiro de 2018 e junho de 2019, com idade entre 35 a 66 anos, sendo 16 pacientes do sexo feminino e 1 do sexo masculino. Todos os pacientes foram operados com exames pré-operatórios dentro da normalidade, condições clínicas satisfatórias e IMC<30. Na presente série de casos, um paciente apresentou epidermólise de coto umbilical; todos os pacientes apresentaram edema e equimoses, e um paciente apresentou seroma no 13º dia de pós-operatório. Hematoma, necrose, infecção, deiscência de ferida operatória ou eventos tromboembólicos não foram observados em nenhum paciente. A técnica demostrou ser segura e eficaz no tratamento de pacientes com excedente cutâneo abdominal, com melhora do contorno corporal, porém há necessidade de maior tempo de acompanhamento pós-operatório e maior número de casos operados para melhor mensurar os resultados, bem como a incidência de complicações.

Morbid obesity is characterized by the accumulation of adipose tissues distributed heterogeneously throughout the body, and gastroplasty is the latest method of surgical treatment. After considerable weight loss, patients present with excess skin under which secretions accumulate, increasing susceptibility for skin infections, which can be minimized with dermolipectomy. Herein, we describe the anchor lipoabdominoplasty technique, adapting the principles of reduced flap detachment, abdominal and flank liposuctions, and preservation of the infraumbilical Scarpa's fascia associated with the preoperative fleurde- lis marking. The technique was used for seventeen patients, including sixteen women and one man, with late postoperative gastroplasty, aged 35­66 years in the period from January 2018 to June 2019. The patients presented with normal preoperative testing, satisfactory clinical conditions, and body mass index scores less than 30 kg/m2. In the present case series, one patient had umbilical cord remnant epidermolysis; all patients had edema and ecchymosis; and one patient had seroma on postoperative day 13. Hematoma, necrosis, infection, wound dehiscence, or thromboembolic events were not observed in any patient. The technique is safe and effective in the treatment of patients with abdominal excess skin, improving their body contour. However, longer postoperative follow-up periods and more cases are necessary to better measure the results and incidence of complications.

Scaling-Up of Bio-Oil Upgrading during Biomass Pyrolysis over ZrO2 /ZSM-5-Attapulgite.

Ex situ catalytic biomass pyrolysis was investigated at both laboratory and bench scale by using a zeolite ZSM-5-based catalyst for selectively upgrading the bio-oil vapors. The catalyst consisted of nanocrystalline ZSM-5, modified by incorporation of ZrO2 and agglomerated with attapulgite (ZrO2 /n-ZSM-5-ATP). Characterization of this material by means of different techniques, including CO2 and NH3 temperature-programmed desorption (TPD), NMR spectroscopy, UV/Vis microspectroscopy, and fluorescence microscopy, showed that it possessed the right combination of accessibility and acid-base properties for promoting the conversion of the bulky molecules formed by lignocellulose pyrolysis and their subsequent deoxygenation to upgraded liquid organic fractions (bio-oil). The results obtained at the laboratory scale by varying the catalyst-to-biomass ratio (C/B) indicated that the ZrO2 /n-ZSM-5-ATP catalyst was more efficient for bio-oil deoxygenation than the parent zeolite n-ZSM-5, producing upgraded bio-oils with better combinations of mass and energy yields with respect to the oxygen content. The excellent performance of the ZrO2 /n-ZSM-5-ATP system was confirmed by working with a continuous bench-scale plant. The scale-up of the process, even with different raw biomasses as the feedstock, reaction conditions, and operation modes, was in line with the laboratory-scale results, leading to deoxygenation degrees of approximately 60 % with energy yields of approximately 70 % with respect to those of the thermal bio-oil.

Transition Metal Phosphide Nanoparticles Supported on SBA-15 as Highly Selective Hydrodeoxygenation Catalysts for the Production of Advanced Biofuels.

A series of catalysts constituted by nanoparticles of transition metal (M = Fe, Co, Ni and Mo) phosphides (TMP) dispersed on SBA-15 were synthesized by reduction of the corresponding metal phosphate precursors previously impregnated on the mesostructured support. All the samples contained a metal-loading of 20 wt% and with an initial M/P mole ratio of 1, and they were characterized by X-ray diffraction (XRD), N2 sorption, H2-TPR and transmission electron microscopy (TEM). Metal phosphide nanocatalysts were tested in a high pressure continuous flow reactor for the hydrodeoxygenation (HDO) of a methyl ester blend containing methyl oleate (C17H33-COO-CH3) as main component (70%). This mixture constitutes a convenient surrogate of triglycerides present in vegetable oils, and following catalytic hydrotreating yields mainly n-alkanes. The results of the catalytic assays indicate that Ni2P/SBA-15 catalyst presents the highest ester conversion, whereas the transformation rate is about 20% lower for MoP/SBA-15. In contrast, catalysts based on Fe and Co phosphides show a rather limited activity. Hydrocarbon distribution in the liquid product suggests that both hydrodeoxygenation and decarboxylation/decarbonylation reactions occur simultaneously over the different catalysts, although MoP/SBA-15 possess a selectivity towards hydrodeoxygenation exceeding 90%. Accordingly, the catalyst based on MoP affords the highest yield of n-octadecane, which is the preferred product in terms of carbon atom economy. Subsequently, in order to conjugate the advantages of both Ni and Mo phosphides, a series of catalysts containing variable proportions of both metals were prepared. The obtained results reveal that the mixed phosphides catalysts present a catalytic behavior intermediate between those of the monometallic phosphides. Accordingly, only marginal enhancement of the yield of n-octadecane is obtained for the catalysts with a Mo/Ni ratio of 3. Nevertheless, owing to this high selectivity for hydrodeoxygenation MoP/SBA-15 appears as a very promising catalyst for the production of advanced biofuels.

Functional bread with n-3 alpha linolenic acid from whole chia (Salvia hispanica L.) flour.

This work proposed to study the effects of the addition of whole chia flour (WCF) on the technological, nutritional and sensory qualities of bread. Different WCF contents (0 and 20 %) and vital gluten (VG) (0 and 4 %) were added to bread according to a 2(2) central composite rotational design. WCF decreased the specific volume, lightness and hue angle of the bread loaves, but did not affect the chroma values. WCF and VG contributed to maintenance of the moisture content of the loaves during the storage period. The increased firmness found with the addition of high levels of WCF (more than 10 %) was countered by larger amounts of VG (more than 2 %). The optimum loaf (10 % WCF and 2 % VG) showed 26 % more lipids, 19 % more protein and 11 % more ash than the standard loaf (0 % WCF and 0 % VG). A better lipid profile was also found (higher omega-3 fatty acid content and a better omega-6/omega-3 ratio). Both breads were positively rated in the sensory profile analysis.

Improving the Thermochemical Energy Storage Performance of the Mn2 O3 /Mn3 O4 Redox Couple by the Incorporation of Iron.

Redox cycles of manganese oxides (Mn2 O3 /Mn3 O4 ) are a promising alternative for thermochemical heat storage systems coupled to concentrated solar power plants as manganese oxides are abundant and inexpensive materials. Although their cyclability for such a purpose has been proved, sintering processes, related to the high-temperature conditions at which charge-discharge cycles are performed, generally cause a cycle-to-cycle decrease in the oxidation rate of Mn3 O4 . To guarantee proper operation, both reactions should present stable reaction rates. In this study, it has been demonstrated that the incorporation of Fe, which is also an abundant material, into the manganese oxides improves the redox performance of this system by increasing the heat storage density, narrowing the redox thermal hysteresis, and, above all, stabilizing and enhancing the oxidation rate over long-term operation, which counteracts the negative effects caused by sintering, although its presence is not avoided.

[Latent tuberculosis infection screening in healthcare workers in four large hospitals in Santiago, Chile]. / Pesquisa de infección tuberculosa latente en personal de la salud en cuatro instituciones de salud en Santiago de Chile.

BACKGROUND: It is currently unknown which is the prevalence of latent tuberculosis infection in healthcare workers in Chile, but this group has been described as at higher risk of developing active tuberculosis than general population. OBJECTIVES: To determine the prevalence of latent tuberculosis infection in a sample of healthcare workers from at risk areas. METHODOLOGY: A cross-sectional, descriptive study, conducted in health care workers from clinical laboratories or respiratory care areas in four hospitals in Santiago. Latent tuberculosis infection detection was determined by Quantiferon® TB Gold In Tube testing (QFT). RESULTS: QFT resulted positive in 20 of 76 (26.3%) of the individuals tested. Test positivity reached 62.5% among the personnel that reported history of past TB contact in the community, 50% among the personnel who belonged to the national tuberculosis control program and 38% among those doing induced sputum, acid fast smear or mycobacterial cultures. The proportion of individuals with positive QFT was significantly lower in those personnel who had no such risk factors (15.7%, p = 0.03). The proportion of latent tuberculosis infection also increased in direct relation to the age of the subject. CONCLUSION: Latent tuberculosis infection as detected by QFT testing was highly prevalent in healthcare workers included in the present study. Further exploring the limitations and possible scenarios for this new diagnostic tool is needed, with emphasis on health personnel at higher-risk and younger individuals.

Pesquisa de infección tuberculosa latente en personal de la salud en cuatro instituciones de salud en Santiago de Chile / Latent tuberculosis infection screening in healthcare workers in four large hospitals in Santiago, Chile

Background: It is currently unknown which is the prevalence of latent tuberculosis infection in healthcare workers in Chile, but this group has been described as at higher risk of developing active tuberculosis than general population. Objectives: To determine the prevalence of latent tuberculosis infection in a sample of healthcare workers from at risk areas. Methodology: A cross-sectional, descriptive study, conducted in health care workers from clinical laboratories or respiratory care areas in four hospitals in Santiago. Latent tuberculosis infection detection was determined by Quantiferon® TB Gold In Tube testing (QFT). Results: QFT resulted positive in 20 of 76 (26.3%) of the individuals tested. Test positivity reached 62.5% among the personnel that reported history of past TB contact in the community, 50% among the personnel who belonged to the national tuberculosis control program and 38% among those doing induced sputum, acid fast smear or mycobacterial cultures. The proportion of individuals with positive QFT was significantly lower in those personnel who had no such risk factors (15.7%, p = 0.03). The proportion of latent tuberculosis infection also increased in direct relation to the age of the subject. Conclusion: Latent tuberculosis infection as detected by QFT testing was highly prevalent in healthcare workers included in the present study. Further exploring the limitations and possible scenarios for this new diagnostic tool is needed, with emphasis on health personnel at higher-risk and younger individuals.

Introducción: Se desconoce en la actualidad cuál es la real prevalencia de infección tuberculosa latente en el personal de salud en Chile; sin embargo, este grupo ha sido descrito como con mayor riesgo de desarrollar tuberculosis activa que la población general. Objetivo: Determinar la prevalencia de infección tuberculosa latente en funcionarios de la salud en diferentes áreas laborales de riesgo. Metodología: Estudio de corte transversal, descriptivo, realizado en funcionarios pertenecientes a laboratorios clínicos o áreas de atención broncopulmonar de cuatro hospitales de la Región Metropolitana en quienes se hizo test de Quantiferon TB Gold®In tube(QFT). Resultados: Se evidenció infección tuberculosa latente en 20 de las 76 (26,3%) personas estudiadas. En aquellos funcionarios que referían antecedente de contacto en el pasado en la comunidad con enfermos de tuberculosis, la positividad del test llegó a 62,5%; en aquellos que pertenecían al Programa Nacional de Control de la Tuberculosis, a 50% y en los que realizaban toma de esputo inducido, baciloscopias o cultivo de micobacterias, a 38%. La proporción de individuos con QFT positivo fue significativamente menor en aquellos funcionarios que no tenían estos antecedentes (15,7%, p = 0,03). Se encontró además una mayor proporción de infección tuberculosa latente a mayor edad del individuo estudiado. Conclusión: La infección tuberculosa latente medida por QFT resultó altamente prevalente en el personal de la salud incluido en el presente estudio. Es necesario seguir profundizando en los posibles escenarios de implementación y limitaciones del uso de esta nueva herramienta diagnóstica, haciendo énfasis en el personal de la salud de mayor riesgo y menor edad.

Pneumocystis colonization in older adults and diagnostic yield of single versus paired noninvasive respiratory sampling.

The presence of Pneumocystis was assessed in oropharyngeal wash specimens from 110 adults (median age, 76 years; age range, 69-95 years), 66 of whom had a paired nasal swab specimen. Pneumocystis jirovecii DNA was detected in 12.8% of oropharyngeal wash specimens, and the frequency increased to 21.5% in paired specimens. Pneumocystis colonization is prevalent in older adults. Double noninvasive sampling increases the diagnostic yield.

Turning TS-1 zeolite into a highly active catalyst for olefin epoxidation with organic hydroperoxides.

A new synthesis route, based on the silanization of zeolitic seeds, has been applied to prepare nanocrystalline TS-1 zeolite with hierarchical porosity, leading to materials exhibiting high catalytic activity in 1-octene epoxidation with organic hydroperoxides as oxidizing agents.

Ordered mesoporous carbons as highly active catalysts for hydrogen production by CH(4) decomposition.

Ordered mesoporous carbons have been applied, for the first time, as catalysts for hydrogen production via methane decomposition, showing higher and more stable activity than commercial carbonaceous catalysts.

Preparation of bimodal micro-mesoporous TiO2 with tailored crystalline properties.

A new mild crystallization procedure has been applied after a synthesis route in the presence of a non-ionic surfactant, leading to the preparation of bimodal micro-mesoporous TiO2, with remarkable textural properties and pore walls formed by anatase nanocrystals, which exhibit photocatalytic activity.