RESUMEN
Magnesium (Mg) and its alloys are a class of promising materials for biodegradable orthopedic and craniomaxillofacial implants; however, rapid release of hydrogen gas remains a key challenge for clinical translation. This study reported the optimal parameters of electrophoretic deposition (EPD), at which magnesium oxide nanoparticles (nMgO) could be deposited onto Mg substrates with homogeneous surface morphology and elemental distribution. The results showed that the distribution and uniformity of the nMgO coatings on Mg improved when the nMgO concentration in ethanol increased and the time of applied voltage decreased. The nMgO-coated Mg showed a homogeneous surface and distinct degradation mode during the 9-day immersion studies in revised simulated body fluid (r-SBF) and Dulbecco's modified Eagle's medium (DMEM), when compared with the noncoated Mg controls. The nMgO coating initially mitigated hydrogen gas formation. The degradation layer on nMgO-coated Mg was thicker than the noncoated Mg and enriched with Ca and P that are favorable for skeletal implant applications. In the direct culture study with bone marrow derived mesenchymal stem cells (BMSCs) in vitro, the cell adhesion density and morphology were not affected by the solubilized degradation products released by the nMgO-coated Mg under indirect contact. However, at the cell-biomaterial interface, the cell spreading decreased under direct contact, possibly because of the continuous dynamic degradation of the samples. The electrophoretically deposited nMgO coatings on Mg-based medical implants should be further studied to improve the coating-substrate and cell-material interfaces for clinical applications.
RESUMEN
This article reports anodization of Mg in KOH electrolyte and the associated surface, degradation, and biological properties for bioresorbable implant applications. The preparation procedures for electrodes and anodization setup significantly enhanced reproducibility of samples. The results of anodization performed at the applied potentials of 1.8, 1.9, or 2.0V showed that the sample anodized at 1.9V and annealed, referred to as the 1.9 AA sample, had homogenous surface microstructure and elemental composition, and a reduction in corrosion current density in the electrochemical testing. In comparison with Mg control, the 1.9 AA sample showed a distinct mode of degradation, e.g., continuous growth of a passivation layer enriched with Ca and P instead of typical localized pitting and undermining, and a greater release rate of Mg2+ ions when immersed in physiologically relevant media. In the direct culture with bone marrow derived mesenchymal stem cells (BMSCs) in vitro, the 1.9 AA sample did not affect BMSC adhesion and morphology under indirect contact; however, the 1.9 AA sample showed a reduction in cell spreading under direct contact. The change in surface topography/composition at the dynamic interface of the anodized-annealed Mg sample might have contributed to the change in BMSC morphology. In summary, this study demonstrated the potential of anodic oxidation to modulate the degradation behaviors of Mg-based biomaterials and BMSC responses in vitro, and confirmed the value of direct culture method for studying cytocompatibility of Mg-based biomaterials for medical implant applications. STATEMENT OF SIGNIFICANCE: Magnesium (Mg)-based biomaterials have been specifically designed and actively explored for biodegradable implant applications since the early 2000s. To realize the benefits of Mg-based materials for medical implant applications, it is critical to control the rate of Mg degradation (i.e. corrosion) in the body. We investigated an environmentally friendly anodization process using KOH electrolyte for modifying the surface of Mg-based materials, and the resulted surface, degradation, and biological properties for biomedical applications. This study reported critical considerations that are important for repeatability of anodization process, homogeneity of surface microstructure and composition, and in vitro evaluations of the degradation and biological properties of surface treated Mg samples. The details in preparation of electrodes, anodization setup, annealing, and sample handling before and after surface treatment (e.g. re-embedding) reported in this article are valuable for studying a variety of electrochemical processes for surface treatment of Mg-based metals, because of enhanced reproducibility.
