Interfacial Reactivity of Silicon Electrodes: Impact of Electrolyte Solvent and Presence of Conductive Carbon.

Silicon (Si) is a promising high-capacity material for lithium-ion batteries; however, its limited reversibility hinders commercial adoption. Approaches such as particle and crystallite size reduction, introduction of conductive carbon, and use of different electrolyte solvents have been explored to overcome these electrochemical limitations. Herein, operando isothermal microcalorimetry (IMC) is used to probe the influence of silicon particle size, electrode composition, and electrolyte additives fluoroethylene carbonate and vinylene carbonate on the heat flow during silicon lithiation. The IMC data are complemented by X-ray photoelectron and Raman spectroscopies to elucidate differences in solid electrolyte interphase (SEI) composition. Nanosized (∼50 nm, n-Si) and micrometer-sized (∼4 µm, µ-Si) silicon electrodes are formulated with and without amorphous carbon and electrochemically lithiated in ethylene carbonate (EC), fluoroethylene carbonate (FEC), or vinylene carbonate (VC) based electrolytes. Notably, n-Si electrodes generate 53-61% more normalized heat relative to their µ-Si counterparts, consistent with increased surface area and electrode/electrolyte reactivity. Introduction of amorphous carbon significantly alters the heat flow profile where multiple exothermic peaks and increased normalized heat dissipation are observed for all electrolyte types. Notably, the VC-containing electrolyte demonstrates the greatest normalized heat dissipation of the electrode compositions tested showing as much as a 50% increase compared to the EC or FEC counterparts. The results are relevant to the understanding of silicon negative electrode function in the presence of electrolyte additives and provide insight relative to silicon containing cell reactivity and safety.

Dry heat sterilization as a method to recycle N95 respirator masks: The importance of fit.

In times of crisis, including the current COVID-19 pandemic, the supply chain of filtering facepiece respirators, such as N95 respirators, are disrupted. To combat shortages of N95 respirators, many institutions were forced to decontaminate and reuse respirators. While several reports have evaluated the impact on filtration as a measurement of preservation of respirator function after decontamination, the equally important fact of maintaining proper fit to the users' face has been understudied. In the current study, we demonstrate the complete inactivation of SARS-CoV-2 and preservation of fit test performance of N95 respirators following treatment with dry heat. We apply scanning electron microscopy with energy dispersive X-ray spectroscopy (SEM/EDS), X-ray diffraction (XRD) measurements, Raman spectroscopy, and contact angle measurements to analyze filter material changes as a consequence of different decontamination treatments. We further compared the integrity of the respirator after autoclaving versus dry heat treatment via quantitative fit testing and found that autoclaving, but not dry heat, causes the fit of the respirator onto the users face to fail, thereby rendering the decontaminated respirator unusable. Our findings highlight the importance to account for both efficacy of disinfection and mask fit when reprocessing respirators to for clinical redeployment.

Characterization of Materials Used as Face Coverings for Respiratory Protection.

Use of masks is a primary tool to prevent the spread of the novel COVID-19 virus resulting from unintentional close contact with infected individuals. However, detailed characterization of the chemical properties and physical structure of common mask materials is lacking in the current literature. In this study, a series of commercial masks and potential mask materials, including 3M Particulate Respirator 8210 N95, a material provided by Oak Ridge National Laboratory Carbon Fiber Technology Facility (ORNL/CFTF), and a Filti Face Mask Material, were characterized by a suite of techniques, including scanning electron microscopy, X-ray diffraction, Raman spectroscopy, and X-ray photoelectron spectroscopy. Wetting properties of the mask materials were quantified by measurements of contact angle with a saliva substitute. Mask pass-through experiments were performed using a dispersed metal oxide nanoparticle suspension to model the SARS-CoV-2 virus, with quantification via spatially resolved X-ray fluorescence mapping. Notably, all mask materials tested provided a strong barrier against respiratory droplet breakthrough. The comparisons and characterizations provided in this study provide useful information when evaluating mask materials for respiratory protection.

Reusing Face Covering Masks: Probing the Impact of Heat Treatment.

The COVID-19 pandemic resulted in imminent shortages of personal protective equipment such as face masks. To address the shortage, new sterilization or decontamination procedures for masks are quickly being developed and employed. Dry heat and steam sterilization processes are easily scalable and allow treatment of large sample sizes, thus potentially presenting fast and efficient decontamination routes, which could significantly ease the rapidly increasing need for protective masks globally during a pandemic like COVID-19. In this study, a suite of structural and chemical characterization techniques, including scanning electron microscopy (SEM), contact angle, X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and Raman were utilized to probe the heat treatment impact on commercially available 3M 8210 N95 Particulate Respirator and VWR Advanced Protection surgical mask. Unique to this study is the use of the synchrotron-based In situ and Operando Soft X-ray Spectroscopy (IOS) beamline (23-ID-2) housed at the National Synchrotron Light Source II at Brookhaven National Laboratory for near-edge X-ray absorption spectroscopy (NEXAFS).

Self-healing, Improved Efficiency Solid State Rechargeable Li/I2 Based Battery.

Solid state electrolytes are receiving significant interest due to the prospect of improved safety, however, addressing the incidence and consequence of internal short circuits remains an important issue. Herein, a battery based on a LiI-LiI(HPN)2 solid state electrolyte demonstrated self-healing after internal shorting where the cells recovered and continued to cycle effectively. The functional rechargeable electrochemistry of the self-forming Li/I2-based battery was investigated through interfacial modification by inclusion of Li metal (at the negative interface), and/or fabricated carbon nanotube substrates at the positive interface. A cell design with lithium metal at the negative and a carbon substrate at the positive interface produced Coulombic efficiencies > 90% over 60 cycles. Finally, the beneficial effects of moderately elevated temperature were established where a 10°C temperature increase led to ~5X lower resistance.

Energy dispersive X-ray diffraction (EDXRD) for operando materials characterization within batteries.

This perspective article describes the use of energy dispersive X-ray diffraction (EDXRD) to study the evolution of electrochemical energy storage materials. Using a synchrotron light source, EDXRD allows crystallographic changes in materials to be tracked from deep within large specimens, due to the use of highly penetrating X-rays and the ability to define a well-controlled diffraction gauge volume in space. Herein we provide an overview of battery work performed using the EDXRD technique, as developed at beamline X17B1 at the National Synchrotron Light Source (NSLS), and continued at beamline 6BM-A at the Advanced Photon Source (APS), beamline I12 at the Diamond Light Source, and beamline 7T-MPW-EDDI at the Berlin Electron Storage Ring Society for Synchrotron Radiation (BESSY II). The High Energy Engineering X-Ray Scattering (HEX) beamline currently under construction at the National Synchrotron Light Source II (NSLS-II) by Brookhaven National Lab and the State of New York will further expand capability for and access to this technique. The article begins with a general introduction to the technique of EDXRD, including a description of the photon energy and d-spacing relationship and a discussion of the gauge volume. The primary topic of the review, battery characterization by EDXRD, includes discussion of batteries of differing materials chemistries (lithium-based batteries and aqueous batteries) which store energy by different mechanisms (insertion and conversion materials). A discussion of high temperature batteries is also included.

The effect of chemically preintercalated alkali ion on structure of layered titanates and their electrochemistry in aqueous energy storage systems.

We introduce a novel chemical preintercalation based synthesis technique based on hydrogen peroxide induced sol-gel process to obtain alkali ion containing ternary layered titanates (MTO, where M = Li, Na, K). Synthesis parameters leading to the formation of single-phase materials with homogeneous elemental distribution are reported for each of the preintercalated ion. Our analyses indicate that the interlayer spacing in the structure of the layered titanates increases with the increase of the radius of the hydrated preintercalated ion. Scanning and transmission electron microscopy imaging revealed morphological diversity: the LTO phase crystallized as nanoplates assembled in "peony-like" spherical agglomerates while NTO and KTO particles exhibited one-dimensional nanobelt or wire-like morphology, with the KTO nanobelts being shorter and more aggregated than the NTO nanobelts. Structural refinement corroborated by electron diffraction and high-resolution transmission electron microscopy revealed that the structure of the LTO phase is built by stacking Ti-O layers containing a single straight layer of connected TiO6 octahedra. The layers in NTO and KTO structures form differently and consist of double Ti-O layers with ragged arrangement of units built by TiO6 octahedra with two titanium rows. The NTO electrodes exhibited the highest electrochemical performance in cells with aqueous 1 M Na2SO4 electrolyte, followed by the KTO electrodes and then LTO electrodes, and this trend is maintained at various scan rates. The established relationships between the structure and electrochemical performance reveal that, in addition to interlayer distance and chemistry of the interlayer region, the structure of the layers can play an important role in charge storage properties of layered oxide electrodes. The double Ti-O layers in the structure of NTO and KTO phases provide a larger number of redox centers which could contribute to the superior electrochemical performance as compared to the LTO electrodes. Our findings indicate that layered materials containing double transition metal oxide layers are promising candidates for exfoliation and assembly with electronically conductive layers with the aim to create 2D heterostructures with high electrochemical performance.

PROGRESS AND OUTLOOK ON FEW COMPONENT COMPOSITE SOLID STATE ELECTROLYTES.

Lithium solid-state composite electrolytes (LiSCEs) provide the opportunity for long life spans, low self-discharge, high reliability, high energy density, and safety. Additionally, this class of electrolytes can be used in electrolytically formed solid-state batteries (EFBs), which may promote reductions in cell manufacturing costs due to their simplicity of design and permit the formation of batteries with diverse architectures. Herein, we provide a discussion of LiSCEs, highlight some of the recent progress in EFB development, and present a forward outlook.

Investigation of prototypal MOFs consisting of polyhedral cages with accessible Lewis-acid sites for quinoline synthesis.

A series of prototypal metal-organic frameworks (MOFs) consisting of polyhedral cages with accessible Lewis-acid sites, have been systematically investigated for Friedländer annulation reaction, a straightforward approach to synthesizing quinoline and its derivatives. Amongst them MMCF-2 demonstrates significantly enhanced catalytic activity compared with the benchmark MOFs, HKUST-1 and MOF-505, as a result of a high-density of accessible Cu(II) Lewis acid sites and large window size in the cuboctahedral cage-based nanoreactor of MMCF-2.