RESUMEN
Petrochemical plants use on-stream inspection often to detect and monitor the corrosion on the equipment and piping system. Compared to ultrasonic thickness gauging and pulse-echo A-scan, phased array corrosion mapping has better coverability and can scan a large area to detect general and localized corrosion. This paper's objective is to obtain documentary evidence for the accuracy of corrosion detection from 30 °C to 250 °C on A36 low-carbon steel by carrying out simulation experiments every 10 °C step. A minimum of three sets of phased array corrosion mapping data in each temperature were collected to study and evaluate the detectability. The data evidence could enhance the confidence level of the plant's end users in using phased array mapping in the future during inspections. The experiments were found to be insufficiently thorough despite addressing the initial concerns, leaving more area for discussion in further studies, such as expanding the investigation to thicker carbon steel, stainless steel, and wedge materials.
RESUMEN
On-stream inspections are the most appropriate method for routine inspections during plant operation without undergoing production downtime. Ultrasonic inspection, one of the on-stream inspection methods, faces challenges when performed at high temperatures exceeding the recommended 52 °C. This study aims to determine the ultrasonic velocity and attenuation with known material grade, thickness, and temperatures by comparing theoretical calculation and experimentation, with temperatures ranging between 30 °C to 250 °C on low-carbon steel, covering most petrochemical equipment material and working conditions. The aim of the theoretical analysis was to obtain Young's modulus, Poisson's ratio, and longitudinal velocity at different temperatures. The experiments validated the theoretical results of ultrasonic change due to temperature increase. It was found that the difference between the experiments and theoretical calculation is 3% at maximum. The experimental data of velocity and decibel change from the temperature range provide a reference for the future when dealing with unknown materials information on site that requires a quick corrosion status determination.
RESUMEN
The structure of energy rotor components includes different structural materials in the sections, which are subjected to varying levels of thermal loading. The first component section has to include a precipitation-hardened nickel-based alloy, while the second one may be manufactured from other materials. Due to the installation cost, the use of expensive nickel-based materials is not recommended for applications in sections with a lower degree of thermal loading. Therefore, this aspect is still actually from an engineering point of view and is discussed in the paper by means of manufacturing and experimental approaches. The paper follows the welding problems related to a hybrid joint made of superalloy (Alloy 59) and hard rusting steel (S355J2W+N steel). The problem is solved using the MIG process at various parameters. With respect to the joint quality, microstructural features and mechanical parameters of the examined zone are presented. In the case of microstructure analysis, the dendritic and cellular natures of austenite were dominant elements of the joint. Mechanical tests have expressed a 50% reduction in elongation of the steel and alloy steel weld and lowering mechanical parameters. Mechanical parameters of the joint were on the level of their values observed for the steel, while the hardening coefficient followed the hardening curve of the alloy. Decohesion of the steel and mixed weld has reflected the constant proportion of values of axial and shear stress components up to the total separation. It is noted the tensile curves of the alloy and alloy steel joint follow a very similar shape, reporting the same response on the monotonic tension. The materials can be analysed by applying constitutive equations at very similar values of their coefficients. The obtained results enabled elaborating and examining the MIG welding process for thick-walled structures (not smaller than 8 mm) in detail giving all parameters required for technology. Finally, the technology for producing a hybrid joint using difficult-to-weld materials with different physical and mechanical properties, such as nickel alloys and low-alloy steels, is proposed. Results have shown it possible to develop a technology for producing of hybrid joints (supper alloy + hard rusting steel) with assumed physical and mechanical properties for rotors applied in the power boiler. This solution was proposed instead of previously used elements of rotors from expensive materials. It was assumed that the newly proposed and utilised method of welding will allow for obtaining good properties in terms of energy devices.
RESUMEN
This study presents the results of testing for abrasive wear of Vanadis 60 SuperClean powder metallurgy steel as compared to Hardox 600 steel and PMFe60P padding weld. The testing was conducted by the "rotating bowl" method using natural abrasive soil masses. Two types of abrasive masses with particle size distributions corresponding to light soil and medium soil were used. The obtained results enable the conclusion that the weight loss for Vanadis 60 SuperClean powder steel in both types of abrasive mass was approximately seven times lower than that for Hardox 600 steel and two times lower than PMFe60P padding weld. The high resistance of powder steel to abrasive wear in abrasive soil masses is related to the presence of a large number of fine M6C (tungsten-molybdenum) and MC (vanadium) carbide precipitates in its microstructure. The obtained test results indicate that the application of Vanadis 60 SuperClean steel may be extended to working elements operating in mineral abrasive environments.
RESUMEN
This study aimed to investigate the possibility of utilizing oat by-products for fiber preparation. Oat husk (OH) and oat bran (OB) were micronized and used to prepare a novel product rich in fiber and with enhanced antioxidant properties. The basic chemical composition and phenolic acid profile were determined in OH and OB. The antioxidant properties of OH and OB were also analyzed. The type and strength of interactions between the biologically active compounds from their mixtures were characterized by an isobolographic analysis. The analyses showed that the sum of phenolic acids was higher in OH than in OB. Ferulic acid was dominant in both OH and OB; however, its content in OH was over sixfold higher than that in OB. The results also suggested that both OH and OB can be used for preparing fiber with enhanced antioxidant properties. The optimal composition of the preparation, with 60-70% of OH and 30-40% of OB, allows for obtaining a product with 60-70% fiber and enhanced antioxidant activity due to bioactive substances and their synergistic effect. The resulting product can be a valuable additive to various food and dietary supplements.
Asunto(s)
Antioxidantes , Avena , Antioxidantes/química , Avena/química , Fibras de la Dieta/análisis , Estructuras de las Plantas/químicaRESUMEN
Oat husk (OH; hull) is a by-product generated from oat processing and is rich in insoluble fibre and phenolic compounds. The aim of this work was to study the particle size distribution, antioxidant activity, and phenolic profile of micronized OH. For this purpose, the hull was first sterilized using superheated steam and was then ground using an impact classifier mill. The particle size distribution (PSD) of the ground husk was determined using the laser diffraction method and the parameters characterizing the PSD of the ground husk, and its antioxidant activity were calculated. In addition, UPLC-MS/MS analysis of phenolic acids was also performed. Micronization of the sterilized husk effectively decreased the size of the particles, and with the increasing speed of the rotor and classifier, the median size of the particles (d50) decreased from 63.8 to 16.7 µm. The following phenolic acids were identified in OH: ferulic, caffeic, p-hydroxybenzoic, vanillic, syringic, and synapic acid. Ferulic acid constituted about 95% of total phenolic acids. The antioxidant activity of the obtained extracts increased as the particle size of the micronized husk decreased. The highest half maximal inhibitory concentration (EC50 index) was found for chelating power, and the lowest was found in the case of radical scavenging activity against DPPH.