RESUMEN
The electrification of ammonia synthesis is a key target for its decentralization and lowering impact on atmospheric CO2 concentrations. The lithium metal electrochemical reduction of nitrogen to ammonia using alcohols as proton/electron donors is an important advance, but requires rather negative potentials, and anhydrous conditions. Organometallic electrocatalysts using redox mediators have also been reported. Water as a proton and electron donor has not been demonstrated in these reactions. Here a N2 to NH3 electrocatalytic reduction using an inorganic molecular catalyst, a tri-iron substituted polyoxotungstate, {SiFe3W9}, is presented. The catalyst requires the presence of Li+ or Na+ cations as promoters through their binding to {SiFe3W9}. Experimental NMR, CV and UV-vis measurements, and MD simulations and DFT calculations show that the alkali metal cation enables the decrease of the redox potential of {SiFe3W9} allowing the activation of N2. Controlled potential electrolysis with highly purified 14N2 and 15N2 ruled out formation of NH3 from contaminants. Importantly, using Na+ cations and polyethylene glycol as solvent, the anodic oxidation of water can be used as a proton and electron donor for the formation of NH3. In an undivided cell electrolyzer under 1 bar N2, rates of NH3 formation of 1.15 nmol sec-1 cm-2, faradaic efficiencies of â¼25%, 5.1 equiv of NH3 per equivalent of {SiFe3W9} in 10 h, and a TOF of 64 s-1 were obtained. The future development of suitable high surface area cathodes and well solubilized N2 and the use of H2O as the reducing agent are important keys to the future deployment of an electrocatalytic ammonia synthesis.
RESUMEN
Semiconducting nanowires are widely studied as building blocks for electro-optical devices; however, their limited cross-section and hence photo-response hinder the utilization of their full potential. Herein, we present an opto-electronic device for broad spectral detection ranging from the visible (VIS) to the short wavelength infra-red (SWIR) regime, using SiGe nanowires coupled to a broadband plasmonic antenna. The plasmonic amplification is obtained by deposition of a metallic nanotip at the edge of a nanowire utilizing a bottom-up synthesis technique. The metallic nanotip is positioned such that both optical plasmonic modes and electrical detection paths are coupled, resulting in a specific detectivity improvement of â¼1000 compared to conventional SiGe NWs. Detectivity and high gain are also measured in the SWIR regime owing to the special plasmonic response. Furthermore, the temporal response is improved by â¼1000. The fabrication process is simple and scalable, and it relies on low-resolution and facile fabrication steps with minimal requirements for top-down techniques.
RESUMEN
Metal nanoparticle arrays are excellent candidates for a variety of applications due to the versatility of their morphology and structure at the nanoscale. Bottom-up self-assembly of metal nanoparticles provides an important complementary alternative to the traditional top-down lithography method and makes it possible to assemble structures with higher-order complexity, for example, nanospheres, nanocubes, and core-shell nanostructures. Here we present a mechanism study of the self-assembly process of 1-D noble metal nanoparticles arrays, composed of Au, Ag, and AuAg alloy nanoparticles. These are prepared within an encapsulated germanium nanowire, obtained by the oxidation of a metal-germanium nanowire hybrid structure. The resulting structure is a 1-D array of equidistant metal nanoparticles with the same diameter, the so-called nanobead (NB) array structure. Atom-probe tomography and transmission electron microscopy were utilized to investigate the details of the morphological and chemical evolution during the oxidation of the encapsulated metal-germanium nanowire hybrid-structures. The self-assembly of nanoparticles relies on the formation of a metal-germanium liquid alloy and the migration of the liquid alloy into the nanowire, followed by dewetting of the liquid during shape-confined oxidation where the liquid column breaks-up into nanoparticles due to the Plateau-Rayleigh instability. Our results demonstrate that the encapsulating oxide layer serves as a structural scaffold, retaining the overall shape during the eutectic liquid formation and demonstrates the relationship between the oxide mechanical properties and the final structural characteristics of the 1-D arrays. The mechanistic details revealed here provide a versatile tool-box for the bottom-up fabrication of 1-D arrays nanopatterning that can be modified for multiple applications according to the RedOx properties of the material system components.