Synthesis and Characterization of Titanium Dioxide Hollow Nanofiber for Photocatalytic Degradation of Methylene Blue Dye.

Environmental crisis and water contamination have led to worldwide exploration for advanced technologies for wastewater treatment, and one of them is photocatalytic degradation. A one-dimensional hollow nanofiber with enhanced photocatalytic properties is considered a promising material to be applied in the field. Therefore, we synthesized titanium dioxide hollow nanofibers (THNF) with extended surface area, light-harvesting properties and an anatase-rutile heterojunction via a template synthesis method and followed by a calcination process. The effect of calcination temperature on the formation and properties of THNF were determined and the possible mechanism of THNF formation was proposed. THNF nanofibers produced at 600 °C consisted of a mixture of 24.2% anatase and 75.8% rutile, with a specific surface area of 81.2776 m2/g. The hollow nanofibers also outperformed the other catalysts in terms of photocatalytic degradation of MB dye, at 85.5%. The optimum catalyst loading, dye concentration, pH, and H2O2 concentration were determined at 0.75 g/L, 10 ppm, pH 11, and 10 mM, respectively. The highest degradation of methylene blue dye achieved was 95.2% after 4 h of UV irradiation.

Development of a P84/ZCC Composite Carbon Membrane for Gas Separation of H2/CO2 and H2/CH4.

Hydrogen (H2) has become one of the promising alternative clean energy resources. Membrane technology is a potential method for hydrogen separation or production. This study aims to develop a new carbon membrane for hydrogen separation or production. Moreover, the permeation behavior of H2, CO2, and CH4 through a hollow fiber composite carbon membrane derived from P84 co-polyimide and with incorporation of zeolite composite carbon (ZCC) was also examined. ZCC was synthesized via the impregnation method of sucrose into zeolite-Y pores, followed by carbonization at 800 °C. Thus, this filler has a high surface area, high microporosity, ordered pore structure, and low hydrophilicity. The presence of zeolites in ZCC is predicted to increase certain gases' affinity for the membrane. Various heating rates (1-5 °C/min) were applied during pyrolysis to understand the effect of the heating rate on the pore structure and H2/CO2 and H2/CH4 gas separation performance. Moreover, gas permeation was evaluated at various temperatures (298-373 K) to study the thermodynamic aspect of the process. A characteristic graphite peak was detected at 2θ ∼ 44° in all carbon samples. Scanning electron microscopy (SEM) observations revealed the void-free surface and the asymmetric structure of the carbon membranes. During the permeation test, it was found that gas permeation through the membrane was significantly affected by the temperature of the separation process. The highest permeability of H2, CO2, and CH4 was detected on the composite carbon membrane at a 3 °C/min heating rate with a permeation temperature of 373 K. The thermodynamic study shows that CO2 and H2 have lower activation energies compared to CH4. The transport mechanism of the membrane involved adsorption and activated surface diffusion. The permeation temperature has a large impact on the transport of small penetrants in the carbon matrix.

The utilization of micro-mesoporous carbon-based filler in the P84 hollow fibre membrane for gas separation.

This research involved carrying out a unique micro-mesoporous carbon particle incorporation into P84 co-polyimide membrane for improved gas separation performance. The carbon filler was prepared using a hard template method from zeolite and known as zeolite-templated carbon (ZTC). This research aims to study the loading amount of ZTC into P84 co-polyimide toward the gas separation performance. The ZTC was prepared using simple impregnation method of sucrose into hard template of zeolite Y. The SEM result showing a dispersed ZTC particle on the membrane surface and cross-section. The pore size distribution (PSD) of ZTC revealed that the particle consists of two characteristics of micro and mesoporous region. It was noted that with only 0.5 wt% of ZTC addition, the permeability was boosted up from 4.68 to 7.06 and from 8.95 to 13.15 barrer, for CO2 and H2 respectively when compared with the neat membrane. On the other hand, the optimum loading was at 1 wt%, where the membrane received thermal stability boost of 10% along with the 62.4 and 35% of selectivity boost of CO2/CH4 and H2/CH4, respectively. It was noted that the position of the filler on the membrane surface was significantly affecting the gas transport mechanism of the membrane. Overall, the results demonstrated that the addition of ZTC with proper filler position is a potential candidate to be applicable in the gas separation involving CO2 and H2.

Superwetting materials for hydrophilic-oleophobic membrane in oily wastewater treatment.

The vast amount of oily wastewater released to the environment through industrialization has worsened the water quality in recent years, posing adverse impacts on general human health. Oil emulsified in water is one of the most difficult mixtures to be treated, making it imperative for new technology to be explored to address this issue. The use of conventional water treatment such as flotation, coagulation, precipitation, adsorption, and chemical treatment have low separation efficiencies and high energy costs, and are not applicable to the separation of oil/water emulsions. Therefore, there is a demand for more efficient methods and materials for the separations of immiscible oil/water mixtures and emulsions. Superwetting materials that can repel oil, while letting water pass through have been widely explored to fit into this concern. These materials usually make use of simultaneous hydrophilic/oleophobic mechanisms to allow a solid surface to separate oily emulsion with little to no use of energy. Also, by integrating specific wettability concepts with appropriate pore scale, solid surfaces may achieve separation of multifarious oil/water mixtures namely immiscible oil/water blends and consolidated emulsions. In this review, materials used to impart superwetting in solid surfaces by focusing on superhydrophilic/superoleophobic wetting properties of the materials categorized into fluorinated and non-fluorinated surface modification are summarized. In each material, its background, mechanism, fabricating processes, and their effects on solid surface's wetting capability are elaborated in detail. The materials reviewed in this paper are mainly organic and green, suggesting the alternative material to replace the fluorine group that is widely used to achieve oleophobicity in oily wastewater treatment.

Novel Activated Carbon Nanofibers Composited with Cost-Effective Graphene-Based Materials for Enhanced Adsorption Performance toward Methane.

Various types of activated carbon nanofibers' (ACNFs) composites have been extensively studied and reported recently due to their extraordinary properties and applications. This study reports the fabrication and assessments of ACNFs incorporated with graphene-based materials, known as gACNFs, via simple electrospinning and subsequent physical activation process. TGA analysis proved graphene-derived rice husk ashes (GRHA)/ACNFs possess twice the carbon yield and thermally stable properties compared to other samples. Raman spectra, XRD, and FTIR analyses explained the chemical structures in all resultant gACNFs samples. The SEM and EDX results revealed the average fiber diameters of the gACNFs, ranging from 250 to 400 nm, and the successful incorporation of both GRHA and reduced graphene oxide (rGO) into the ACNFs' structures. The results revealed that ACNFs incorporated with GRHA possesses the highest specific surface area (SSA), of 384 m2/g, with high micropore volume, of 0.1580 cm3/g, which is up to 88% of the total pore volume. The GRHA/ACNF was found to be a better adsorbent for CH4 compared to pristine ACNFs and reduced graphene oxide (rGO/ACNF) as it showed sorption up to 66.40 mmol/g at 25 °C and 12 bar. The sorption capacity of the GRHA/ACNF was impressively higher than earlier reported studies on ACNFs and ACNF composites. Interestingly, the CH4 adsorption of all ACNF samples obeyed the pseudo-second-order kinetic model at low pressure (4 bar), indicating the chemisorption behaviors. However, it obeyed the pseudo-first order at higher pressures (8 and 12 bar), indicating the physisorption behaviors. These results correspond to the textural properties that describe that the high adsorption capacity of CH4 at high pressure is mainly dependent upon the specific surface area (SSA), pore size distribution, and the suitable range of pore size.

New Perspectives on Fuel Cell Technology: A Brief Review.

Energy storage and conversion is a very important link between the steps of energy production and energy consumption. Traditional fossil fuels are a natural and unsustainable energy storage medium with limited reserves and notorious pollution problems, therefore demanding a better choice to store and utilize the green and renewable energies in the future. Energy and environmental problems require a clean and efficient way of using the fuels. Fuel cell functions to efficiently convert oxidant and chemical energy accumulated in the fuel directly into DC electric, with the by-products of heat and water. Fuel cells, which are known as effective electrochemical converters, and electricity generation technology has gained attention due to the need for clean energy, the limitation of fossil fuel resources and the capability of a fuel cell to generate electricity without involving any moving mechanical part. The fuel cell technologies that received high interest for commercialization are polymer electrolyte membrane fuel cells (PEMFCs), solid oxide fuel cells (SOFCs), and direct methanol fuel cells (DMFCs). The optimum efficiency for the fuel cell is not bound by the principle of Carnot cycle compared to other traditional power machines that are generally based on thermal cycles such as gas turbines, steam turbines and internal combustion engines. However, the fuel cell applications have been restrained by the high cost needed to commercialize them. Researchers currently focus on the discovery of different materials and manufacturing methods to enhance fuel cell performance and simplify components of fuel cells. Fuel cell systems' designs are utilized to reduce the costs of the membrane and improve cell efficiency, durability and reliability, allowing them to compete with the traditional combustion engine. In this review, we primarily analyze recent developments in fuel cells technologies and up-to-date modeling for PEMFCs, SOFCs and DMFCs.

Adsorptive removal of heavy metal ions using graphene-based nanomaterials: Toxicity, roles of functional groups and mechanisms.

The endless introduction of toxic heavy metals through industrialization has worsened the heavy metal pollution in the environment. Thus, the need for its effective removal has become more crucial than before. Studies on graphene-based nanomaterials and their use in removing heavy metals are gaining tremendous traction over the past decade. The properties of graphene oxide (GO), such as large surface areas, desired functional groups and excellent mechanical properties are advantageous. Nevertheless, due to its tendency to agglomerate and difficulty in phase separation after treatment, the functionalization of GO using various materials of different surface functional groups is an ongoing study. The surface modification of GO is done by using various materials to introduce heteroatoms, which have high affinity for heavy metals. This review summarizes the utilization of different surface functional groups, such as oxygen-containing, nitrogen-containing, and sulphur-containing functionalized graphene oxide composites in the adsorption of cationic and oxyanionic heavy metals. The toxicity of these heavy metals is also addressed. Furthermore, the interactions between adsorbents and heavy metals which are influenced by pH and surface functional groups, are also discussed in detail. This is followed by the review in adsorption isotherms and kinetics. Future research needs are also offered.

Development of Copper-Aluminum Layered Double Hydroxide in Thin Film Nanocomposite Nanofiltration Membrane for Water Purification Process.

This study aims to fabricate a thin film composite (TFC) membrane, modified with copper-aluminium layered double hydroxide (LDH) nanofillers via interfacial polymerization technique for nanofiltration (NF) processes. It was found that Cu-Al LDH nanofillers possessed layered structured materials with typical hexagonal plate-like shape and positive surface charge. The study revealed that TFN membrane exhibits a relatively smooth surface and a less nodular structure compared to pristine TFC membrane. The contact angle of TFN progressively decreased from 54.1° to 37.25°, indicating enhancement in surface hydrophilicity. Moreover, the incorporation of LDH nanofillers resulted in a less negative membrane as compared to the pristine TFC membrane. The best NF performance was achieved by TFN2 membrane with 0.1° of Cu-Al LDH loading and a water flux of 7.01 Lm-2h-1.bar. The addition of Cu-Al LDH resulted in excellent single salt rejections of Na2SO4 (96.8%), MgCl2 (95.6%), MgSO4 (95.4%), and NaCl (60.8%). The improvement in anti-fouling properties of resultant TFN membranes can be observed from the increments of pure water flux recovery and normalized water flux by 14% and 25% respectively. The findings indicated that Cu-Al LDH is a promising material in tailoring membrane surface properties and fouling resistance. The modification of the LDH-filled TFN membrane shows another alternative to fabricating a high-performance composite membrane, especially for water softening and partial desalination process.