RESUMEN
Integrated quantum photonic circuits require the efficient coupling of photon sources to photonic waveguides. Hybrid plasmonic/photonic platforms are a promising approach, taking advantage of both plasmon modal confinement for efficient coupling to a nearby emitter and photonic circuitry for optical data transfer and processing. In this work, we established directional quantum dot (QD) emission coupling to a planar TiO2waveguide assisted by a Yagi-Uda antenna. Antenna on waveguide is first designed by scaling radio frequency dimensions to nano-optics, taking into account the hybrid plasmonic/photonic platform. Design is then optimized by full numerical simulations. We fabricate the antenna on a TiO2planar waveguide and deposit a few QDs close to the Yagi-Uda antenna. The optical characterization shows clear directional coupling originating from antenna effect. We estimate the coupling efficiency and directivity of the light emitted into the waveguide.
RESUMEN
Optical refractive-index sensors exploiting selective co-integration of plasmonics with silicon photonics has emerged as an attractive technology for biosensing applications that can unleash unprecedented performance breakthroughs that reaps the benefits of both technologies. However, towards this direction, a major challenge remains their integration using exclusively CMOS-compatible materials. In this context, herein, we demonstrate, for the first time to our knowledge, a CMOS-compatible plasmo-photonic Mach-Zehnder-interferometer (MZI) based on aluminum and Si3N4 waveguides, exhibiting record-high bulk sensitivity of 4764â nm/RIU with clear potential to scale up the bulk sensitivity values by properly engineering the design parameters of the MZI. The proposed sensor is composed of Si3N4 waveguides butt-coupled with an aluminum stripe in one branch to realize the sensing transducer. The reference arm is built by Si3N4 waveguides, incorporating a thermo-optic phase shifter followed by an MZI-based variable optical attenuation stage to maximize extinction ratio up to 38â dB, hence optimizing the overall sensing performance. The proposed sensor exhibits the highest bulk sensitivity among all plasmo-photonic counterparts, while complying with CMOS manufacturing standards, enabling volume manufacturing.
RESUMEN
We demonstrate a photonic integrated Mach-Zehnder interferometric sensor, utilizing a plasmonic stripe waveguide in the sensing branch and a photonic variable optical attenuator and a phase shifter in the reference arm to optimize the interferometer operation. The plasmonic sensor is used to detect changes in the refractive index of the surrounding medium exploiting the accumulated phase change of the propagating Surface-Plasmon-Polariton (SPP) mode that is fully exposed in an aqueous buffer solution. The variable optical attenuation stage is incorporated in the reference Si3N4 branch, as the means to counter-balance the optical losses introduced by the plasmonic branch and optimize interference at the sensor output. Bulk sensitivity values of 1930 nm/RIU were experimentally measured for a Mach Zehnder Interferometer (MZI) with a Free Spectral Range of 24.8 nm, along with extinction ratio of more than 35 dB, demonstrating the functional benefits of the co-integration of plasmonic and photonic waveguides.
Asunto(s)
Técnicas Biosensibles/métodos , Interferometría/métodos , Óptica y Fotónica/métodos , Compuestos de Silicona/química , Electricidad , RefractometríaRESUMEN
We demonstrate wavelength-division-multiplexed (WDM) 200 Gb/s (8 × 25 Gb/s) data transmission over 100 µm long aluminum (Al) surface-plasmon-polariton (SPP) waveguides on a Si3N4 waveguide platform at telecom wavelengths. The Al SPP waveguide was evaluated in terms of signal integrity by performing bit-error-rate (BER) measurements that revealed error-free operation for all eight 25 Gb/s non-return-to-zero (NRZ) modulated data channels with power penalties not exceeding 0.2 dB at 10-9. To the best of our knowledge, this is the first demonstration of WDM enabled data transmission over complementary-metal-oxide-semiconductor (CMOS) SPP waveguides fueling future development of CMOS compatible plasmo-photonic devices for on-chip optical interconnections.
RESUMEN
Damping distances of surface plasmon polariton modes sustained by different thin titanium nitride (TiN) films are measured at the telecom wavelength of 1.55 µm. The damping distances are correlated to the electrical direct current resistivity of the films sustaining the surface plasmon modes. It is found that TiN/Air surface plasmon mode damping distances drop non-linearly from 40 to 16µm as the resistivity of the layers increases from 28 to 130µΩ.cm, respectively. The relevance of the direct current (dc) electrical resistivity for the characterization of TiN plasmonic properties is investigated in the framework of the Drude model, on the basis of parameters extracted from spectroscopic ellipsometry experiments. By probing a parametric space of realistic values for parameters of the Drude model, we obtain a nearly univocal dependence of the surface plasmon damping distance on the dc resistivity demonstrating the relevance of dc resistivity for the evaluation of the plasmonic performances of TiN at telecom frequencies. Finally, we show that better plasmonic performances are obtained for TiN films featuring a low content of oxygen. For low oxygen content and corresponding low resistivity, we attribute the increase of the surface plasmon damping distances to a lower confinement of the plasmon field into the metal and not to a decrease of the absorption of TiN.
RESUMEN
Dielectric loaded surface plasmon waveguides (DLSPPWs) comprised of polymer ridges deposited on top of CMOS compatible metal thin films are investigated at telecom wavelengths. We perform a direct comparison of the properties of copper (Cu), aluminum (Al), titanium nitride (TiN) and gold (Au) based waveguides by implementing the same plasmonic waveguiding configuration for each metal. The DLSPPWs are characterized by leakage radiation microscopy and a fiber-to-fiber configuration mimicking the cut-back method. We introduce the ohmic loss rate (OLR) to analyze quantitatively the properties of the CMOS metal based DLSPPWs relative to the corresponding Au based waveguides. We show that the Cu, Al and TiN based waveguides feature extra ohmic loss compared to Au of 0.027 dB/µm, 0.18 dB/µm and 0.52 dB/µm at 1550nm respectively. The dielectric function of each metal extracted from ellipsometric spectroscopic measurements is used to model the properties of the DLSP-PWs. We find a fairly good agreement between experimental and modeled DLSPPWs properties except for Al featuring a large surface roughness. Finally, we conclude that TiN based waveguides sustaining intermediate effective index (in the range 1.05-1.25) plasmon modes propagate over very short distances restricting the the use of those modes in practical situations.
RESUMEN
In this paper we report on a low energy consumption CMOS-compatible plasmonic modulator based on Franz-Keldysh effect in germanium on silicon. We performed integrated electro-optical simulations in order to optimize the main characteristics of the modulator. A 3.3 dB extinction ratio for a 30 µm long modulator is demonstrated under 3 V bias voltage at an operation wavelength of 1647 nm. The estimated energy consumption is as low as 20 fJ/bit.
RESUMEN
We investigate numerically a novel plasmonic polarization converter relying on the excitation of a so-called dihedron dielectric loaded plasmon polariton. The dihedron dielectric loaded waveguide consists of a dielectric ridge implemented at the inner corner of a metal-coated dielectric step. For a dielectric ridge with a square cross section, the plasmon polariton modes supported by each side of the metallized step hybridize to create supermodes with crossed polarizations. We show that the two supermodes can be operated in a dual-mode interferometer configuration to perform an efficient (24 dB) TE-TM/TM-TE polarization conversion over typical distances below 30 µm at telecommunications wavelengths. In addition, on the basis of the thermo-optical properties of our device, we find that the dihedron plasmonic polarization converter is temperature insensitive.
RESUMEN
The thermo-optical dynamics of polymer loaded surface plasmon waveguide (PLSPPW) based devices photo-thermally excited in the nanosecond regime is investigated. We demonstrate thermo-absorption of PLSPPW modes mediated by the temperature-dependent ohmic losses of the metal and the thermally controlled field distribution of the plasmon mode within the metal. For a PLSPPW excited by sub-nanosecond long pulses, we find that the thermo-absorption process leads to modulation depths up to 50% and features an activation time around 2 ns whereas the relaxation time is around 800 ns, four-fold smaller than the cooling time of the metal film itself. Next, we observe the photo-thermal activation of PLSPPW racetrack shaped resonators at a time scale of 300 ns followed however by a long cooling time (18 µs) attributed to the poor heat diffusivity of the polymer. We conclude that nanosecond excitation combined to high thermal diffusivity materials opens the way to high speed thermo-optical plasmonic devices.
RESUMEN
We report on photo-thermal modulation of thin film surface plasmon polaritons (SPP) excited at telecom wavelengths and traveling at a gold/air interface. By operating a modulated continuous-wave or a Q-switched nanosecond pump laser, we investigate the photo-thermally induced modulation of SPP propagation mediated by the temperature-dependent ohmic losses in the gold film. We use a fiber-to-fiber characterization set-up to measure accurately the modulation depth of the SPP signal under photo-thermal excitation. On the basis of these measurements, we extract the thermo-plasmonic coefficient of the SPP mode defined as the temperature derivative of the SPP damping constant. Next, we introduce a figure of merit which is relevant to characterize the impact of temperature onto the properties of bounded or weakly leaky SPP modes supported by a given metal at a given wavelength. By combining our measurements with tabulated values of the temperature-dependent imaginary part of gold dielectric function, we compute the thermo-optical coefficients (TOC) of gold at telecom wavelengths. Finally, we investigate a pulsed photo-thermal excitation of the SPP in the nanosecond regime. The experimental SPP depth of modulation obtained in this situation are found to be in fair agreement with the modulation depths computed by using our values of gold TOC.
RESUMEN
We report on the photo-thermal activation of dielectric loaded plasmonic switches comprised of gold nanoparticle-doped polymer deposited onto a gold film. The plasmonic switches rely on a multi-mode interferometer design and are fabricated by electron beam lithography applied to a positive resin doped with gold nanoparticles at a volume ratio of 0.52%. A cross-bar switching is obtained at telecom wavelengths by pumping the devices with a visible beam having a frequency within the localized surface plasmon resonance band of the embedded nanoparticles. By comparing the switching performances of doped and undoped devices, we show that for the modest doping level we consider, the power needed to activate the doped switches is reduced by a factor 2.5 compared to undoped devices. The minimization of activation power is attributed to enhanced light-heat conversion and optimized spatial heat generation for doped devices and not to a change of the thermo-optic coefficient of the doped polymer.
Asunto(s)
Oro/química , Nanopartículas del Metal/química , Nanotecnología/instrumentación , Óptica y Fotónica/instrumentación , Resonancia por Plasmón de Superficie/instrumentación , Telecomunicaciones/instrumentación , Diseño de Equipo , Análisis de Elementos Finitos , Calor , Luz , Microtecnología/instrumentación , Microtecnología/métodos , Modelos Teóricos , Nanotecnología/métodos , Óptica y Fotónica/métodos , Polímeros/química , Resonancia por Plasmón de Superficie/métodosRESUMEN
We demonstrate Wavelength Division Multiplexed (WDM)-enabled transmission of 480Gb/s aggregate data traffic (12x40Gb/s) as well as high-quality 1x2 thermo-optic tuning in Dielectric-Loaded Surface Plasmon Polariton Waveguides (DLSPPWs). The WDM transmission characteristics have been verified through BER measurements by exploiting the heterointegration of a 60 µm-long straight DLSPPW on a Silicon-on-Insulator waveguide platform, showing error-free performance for six out of the twelve channels. High-quality thermo-optic tuning has been achieved by utilizing Cycloaliphatic-Acrylate-Polymer as an efficient thermo-optic polymer loading employed in a dual-resonator DLSPPW switching structure, yielding a 9 nm wavelength shift and extinction ratio values higher than 10 dB at both output ports when heated to 90°C.
Asunto(s)
Dispositivos Ópticos , Procesamiento de Señales Asistido por Computador/instrumentación , Resonancia por Plasmón de Superficie/instrumentación , Telecomunicaciones/instrumentación , Diseño de Equipo , Análisis de Falla de Equipo , TemperaturaRESUMEN
We develop a theoretical model to compute the local density of states in a confined plasmonic waveguide. Based on this model, we derive a simple formula with a clear physical interpretation for the lifetime modification of emitters embedded in the waveguide. The gain distribution within the active medium is then computed following the formalism developed in a recent work [Phys. Rev. B 78, 161401 (2008)], by taking rigorously into account the pump irradiance and emitters lifetime modifications in the system. We finally apply this formalism to describe gain-assisted propagation in a dielectric-loaded surface plasmon polariton waveguide.
Asunto(s)
Simulación por Computador , Luz , Modelos Teóricos , Dispositivos Ópticos , Resonancia por Plasmón de Superficie/instrumentación , Diseño Asistido por Computadora , Diseño de Equipo , Dispersión de Radiación , Pesos y MedidasRESUMEN
Using a single-mode dielectric-loaded surface plasmon polariton waveguide doped with quantum dots, we were able to slightly increase the propagation length of the mode by stimulated emission of plasmon. We analyse the amplification phenomenon in the visible range by combining leakage radiation microscopy and surface plasmon coupled emission techniques.
RESUMEN
This paper demonstrates the efficiency of the differential method, a conventional grating theory, to investigate dielectric loaded surface plasmon polariton waveguides (DLSPPWs), known to be a potential solution for optical interconnects. The method is used to obtain the mode effective indices (both real and imaginary parts) and the mode profiles. The results obtained with the differential method are found to be in good agreement with those provided by the effective index method or finite elements. The versatility of the differential method is demonstrated by considering complex configurations such as trapezoidal waveguides or DLSPPWs lying on a finite width metal stripe.
RESUMEN
We analytically and numerically analyze the fluorescence decay rate of a quantum emitter placed in the vicinity of a spherical metallic particle of mesoscopic size (i.e with dimensions comparable to the emission wavelength). We discuss the efficiency of the radiative decay rate and non-radiative coupling to the particle as well as their distance dependence. The electromagnetic coupling mechanisms between the emitter and the particle are investigated by analyzing the role of the plasmon modes and their nature (dipole, multipole or interface mode). We demonstrate that near-field coupling can be expressed in a simple form verifying the optical theorem for each particle modes.
RESUMEN
We introduce a new experimental method to measure the local electromagnetic density of states (LDOS) by integrating the differential scattering cross section. The signal detected essentially reflects the intrinsic scattering response of the photonic structures and renders the partial LDOS dominated by evanescent modes. We give a theoretical understanding of the LDOS image formation and show a qualitative agreement between experimental images and theoretical maps. This approach can be practically applied to the direct measurement of an optical antenna's scattering efficiency and can provide valuable information for designing optimum structures utilized in radiative decay engineering.
RESUMEN
We show that interfering surface plasmon polaritons can be excited with a focused laser beam at normal incidence to a plane metal film. No protrusions or holes are needed in this excitation scheme. Depending on the axial position of the focus, the intensity distribution on the metal surface is either dominated by interferences between counterpropagating plasmons or by a two-lobe pattern characteristic of localized surface plasmon excitation. Our experiments can be accurately explained by use of the angular spectrum representation and provide a simple means for locally exciting standing surface plasmon polaritons.
RESUMEN
The optical properties of in-plane integrated surface plasmon polariton (SPP) cavities comprised of a thin film area sandwiched between two one-dimensional Bragg SPP mirrors are investigated numerically and experimentally. We discuss the resonance condition of these cavities, and we analyze in details the physical origin of the dispersion of this resonance. On the basis of numerical results, we show that in-plane SPP cavities can be used to achieve local SPP field enhancement and antireflecting SPP layers. The numerical results are compared to near-field optical images recorded by operating a photon scanning tunneling microscope. From the near-field images recorded over cavities with different sizes at different frequencies, we verify the resonance condition obtained numerically and we measure the quality factor of a submicrometer in-plane integrated SPP cavity.
RESUMEN
The launching of surface plasmons by micro-gratings of subwavelength apertures milled in a thick metal film is important for the development of surface plasmon based circuits. By comparing the near-field optical images of such surface plasmon sources with the results of a Huygens-Fresnel principle based scattering model, we show that the properties of the locally launched SP beams such as divergence or uniformity can be tuned by adjusting the shape of the micro-gratings. This allows us to propose an optimized source array well adapted for providing a narrow, collimated and uniform beam.