Microstructural characterization, mechanical and microbiological properties of acrylic resins added with reduced graphene oxide.

To evaluate the microstructural characterization, mechanical properties and antimicrobial activity of acrylic resins incorporated with different concentrations of reduced graphene oxide (rGO). Specimens were made of self-cured and heat-cured acrylic resins for the control group and concentrations of 0.5%, 1%, and 3%. The microstructural characterization was evaluated by scanning electron microscopy (SEM) and energy-dispersive X-ray (EDS). For mechanical testing, flexural strength, and Knoop hardness tests were performed. Microbiological evaluations were performed by colony forming units (CFU) analysis, tetrazolium salt reduction (XTT), and SEM images. The modified acrylic resins showed increased mechanical properties at low concentrations (p < 0.05) and with reduced S. mutans (p < 0.05). Reduced graphene oxide interfered with the mechanical performance and microbiological properties of acrylic resins depending on the concentration of rGO, and type of polymerization and microorganism evaluated. The incorporation of graphene compounds into acrylic resins is an alternative to improve the antimicrobial efficacy and performance of the material.

Structure-properties correlation of acrylic resins modified with silver vanadate and graphene.

This study aimed to incorporate ß-AgVO3 and rGO into self-curing (SC) and heat-curing (HC) acrylic resins and to evaluate their physicochemical, mechanical, and antimicrobial properties while correlating them with the characterized material structure. Acrylic resin samples were prepared at 0 % (control), 0.5 %, 1 %, and 3 % for both nanoparticles. The microstructural characterization was assessed by scanning electron microscopy (SEM) (n = 1) and energy dispersive X-ray spectroscopy (EDS) (n = 1). The physicochemical and mechanical tests included flexural strength (n = 10), Knoop hardness (n = 10), roughness (n = 10), wettability (n = 10), sorption (n = 10), solubility (n = 10), porosity (n = 10), and color evaluation (n = 10). The microbiological evaluation was performed by counting colony-forming units (CFU/mL) and cell viability (n = 8). The results showed that the ß-AgVO3 samples showed lower counts of Candida albicans, Pseudomonas aeruginosa, and Streptococcus mutans due to their promising physicochemical properties. The mechanical properties were maintained with the addition of ß-AgVO3. The rGO samples showed higher counts of microorganisms due to the increase in physicochemical properties. It can be concluded that the incorporation of ß-AgVO3 into acrylic resins could be an alternative to improve the antimicrobial efficacy and performance of the material.

Influence of abrasive dentifrices on polymeric reconstructive material properties after simulated toothbrushing.

To assess the influence of dentifrices with different abrasiveness levels on the properties of dental reconstructive materials. Forty-eight cylinders were obtained from four polymeric materials, being two CAD/CAM acrylic resins (Ivotion-Dent and Ivotion-Base), one injected acrylic resin (IvoBase-Hydrid) and one light-cured resin composite (Empress Direct). Specimens were allocated to four subgroups for toothbrushing simulation according to the dentifrice relative dentin abrasivity (RDA) and silica content: (i) RDA 0 = 0%; (ii) RDA 50 = 3%; (iii) RDA 100 = 10%; and (iv) RDA 120 = 25%. Specimens were then subjected to toothbrushing. Surface analyses [surface roughness Ra (SR) and scanning electron microscopy (SEM)] along with hardness and optical properties [translucency parameter (TP) and contrast ratio (CR)] were evaluated before and after toothbrushing. Statistical analyses were performed using ANOVA and Tukey test. A significant increase in SR was observed after toothbrushing with higher RDA toothpastes for Ivotion-Dent (100 and 120) and IvoBase-Hybrid (120). Ivotion-Base and Empress Direct presented no significant differences in SR when analyzed as a function of timepoint and RDA levels. Hardness was not influenced by toothbrushing with different RDA dentifrices, except for Empress Direct with RDA 0 toothpaste, where a decrease in the hardness was observed. TP of Ivotion-Dent and Empress Direct significantly decreased after toothbrushing with higher RDA dentifrices and CR of Ivotion-Dent, Empress Direct and IvoBase-Hybrid significantly increased with higher RDA dentifrices. The levels of dentifrice abrasiveness affected differently the SR, hardness and optical properties of polymeric reconstructive materials after toothbrushing.

Effect of Hygiene Protocols on the Mechanical and Physical Properties of Two 3D-Printed Denture Resins Characterized by Extrinsic Pigmentation as Well as the Mixed Biofilm Formed on the Surface.

To assess the effect of hygiene protocols and time on the physical-mechanical properties and colony-forming units (CFU) of Candida albicans, Staphylococcus aureus, and Streptococcus mutans on 3D-printed denture resins (SmartPrint and Yller) with extrinsic pigmentation compared to conventional resin (CR). The protocols were evaluated: brushing (B), brushing and immersion in water (W), 0.25% sodium hypochlorite (SH), and 0.15% triclosan (T), simulating 0, 1, 3, and 5 years. The data were analyzed by ANOVA with repeated measurements, ANOVA (Three-way) and Tukey's post-test, generalized linear model with Bonferroni adjustment, and ANOVA (Two-way) and Tukey's post-test (α = 0.05). The protocols influenced color (p = 0.036) and Knoop hardness (p < 0.001). Surface roughness was influenced by protocols/resin (p < 0.001) and time/resin (p = 0.001), and flexural strength by time/protocols (p = 0.014). C. albicans showed interactions with all factors (p = 0.033). Staphylococcus aureus was affected by protocols (p < 0.001). Streptococcus mutans exhibited no count for SH and T (p < 0.001). Yller resin showed more color changes. The 3D-printed resins displayed lower microhardness, increased roughness, and decreased flexural strength compared to CR with all protocols in a simulated period of 5 years. The indication of printed resins should be restricted to less than 3 years.

Efeito dos diferentes tipos de polimento sobre a rugosidade de superfície de uma resina acrílica comercial quimicamente ativada: estudo in vitro / Effect of different types of polishing on the surface roughness of a chemically activated commercial acrylic resin: an in vitro study

Objetivo: avaliar in vitro o polimento sobre resina acrílica quimicamente ativada (RAQA), por meio da rugosidade de superfície (Ra). Materiais e Método: Foram confeccionadas 40 amostras de RAQA, com dimensões de 10 a 10 x 2 mm, e foram divididas em quatro grupos (n=10): ausência do acabamento (AA); Ausência de polimento (AP); Polimento químico (PQ); Polimento com borrachas siliconadas + Escovas (PM). Os espécimes foram avaliados no quanto a rugosidade média (Ra) antes e após o envelhecimento em água destilada em uma estufa por 60 dias. Três medições de Ra (µm), na horizontal foram realizadas e calculada uma média para cada espécime. Os dados foram analisados de forma descritiva e inferencial, ANOVA de medidas repetidas e teste de Tukey com nível de significância de 5%. Resultados: Inicialmente, o grupo AA teve os menores valores de Ra e o grupo AP os maiores valores de rugosidade, com média e desvio padrão respectivamente 0,17 (±0,11) e 0,52 (±0,10). Após o envelhecimento, o grupo AA teve as menores médias e o grupo PQ os maiores valores de Ra, sendo 0,38 (±0,20) e 1,33 (±0,32), respectivamente. Os resultados evidenciaram diferença estatística significante quando as amostras foram submetidas ao acabamento com brocas. Conclusão: A RAQA necessita de polimento após acabamento com brocas, uma vez que a ausência de polimento comprometerá a lisura de superfície do material.(AU)

Objective: to evaluate in vitro polishing on chemically activated acrylic resin (RAQA), using surface roughness (Ra). Materials and Method: 40 RAQA samples were made, measuring 10 to 10 x 2 mm, and divided into four groups (n=10): absence of finishing (AA); Lack of polishing (AP); Chemical polishing (PQ); Polishing with silicone rubbers + Brushes (PM). The specimens were evaluated for their average roughness (Ra) before and after aging in distilled water in an oven for 60 days. Three horizontal Ra (µm) measurements were taken and an average was calculated for each specimen. Data were analyzed descriptively and inferentially, using repeated measures ANOVA and Tukey test with a significance level of 5%. Results: Initially, the AA group had the lowest Ra values and the AP group the highest roughness values, with mean and standard deviation respectively 0.17 (±0.11) and 0.52 (±0.10). After aging, the AA group had the lowest averages and the PQ group the highest Ra values, being 0.38 (±0.20) and 1.33 (±0.32), respectively. The results showed a statistically significant difference when the samples were finished with drills. Conclusion: RAQA requires polishing after finishing with drills, as the lack of polishing will compromise the surface smoothness of the material.(AU)

Do denture cleansers influence the surface roughness and adhesion and biofilm formation of Candida albicans on acrylic resin? Systematic review and meta-analysis.

PURPOSE: To evaluate the influence of denture cleansers on the surface roughness, Candida albicans adhesion, and biofilm formation on denture base acrylic resins. STUDY SELECTION: Electronic databases and gray literature were searched using an individual search strategy. In vitro studies that evaluated the effects of immersion in denture cleansers on the surface roughness (µm) and antimicrobial activity (CFU/mL) on samples of heat-polymerized denture base acrylic resins were included. RESULTS: After screening, 17 studies were included, and a qualitative synthesis was performed. After assessing the risk of bias, only nine studies were included in the meta-analysis. The meta-analysis results showed that the evaluated solutions (0.5% sodium hypochlorite, 1% sodium hypochlorite, alkaline peroxide, and natural substances) did not influence the roughness of the acrylic resin. However, in the qualitative analysis, it was not possible to confirm an association between roughness and C. albicans adhesion and biofilm formation on the acrylic resin samples. CONCLUSION: Denture cleansers did not affect the surface roughness of denture base acrylic resins.

Influence of Light-Curing Glaze and Chlorhexidine Gluconate in the Acrylic Resin Properties: An in situ Study.

This in-situ study aimed to evaluate the chromatic stability, microhardness, and surfacefree energy of chemically activated acrylic resin (CAAR) samples. Eighty CAAR samples were made and each volunteer (n = 20) received two palatal plates with two sides of groups (without and with glaze application). The samples were exposed to two conditions: the control condition (sucrose 30%) and the test condition (sucrose 30% and 0.12% chlorhexidine). The volunteers used the first palatal device (control condition) for seven days and the second palatal device (test condition) for another seven days, with a seven-day break between them. Then, the ΔΕ00, microhardness, and surface-free energy tests were performed. Analysis of Variance and the Tukey test were used (α = 0.05). The control group with glaze showed higher ΔΕ00 compared to the group without the glaze. The test group with glaze had less ΔΕ00 than their respective controls. In both periods, when the glaze was applied, higher microhardness values were found for all groups. Groups with glaze showed lower roughness and higher surface-free energy than groups without the glaze. The values obtained in this study were satisfactory, showing the clinical efficacy of glaze and the use of 0.12% CH for maintaining the physical and mechanical properties of CAAR.

Influência de diferentes tratamentos de superfície na resistência de união entre PEEK e materiais de revestimento estético: revisão sistemática e metaanálise / The influence of different surface treatments on the bond strength between PEEK and aesthetic coating materials: a systematic review and meta-analysis

Poliéter-éter-cetona (Polyetheretherketone - PEEK) é um polímero de excelentes propriedades mecânicas, o que o torna um potencial candidato para substituir ligas metálicas em diversas especialidades odontológicas. Quando utilizado como infraestrutura para confecção de próteses odontológicas, a adesão do PEEK ao material de revestimento estético é determinante para a longevidade do tratamento, embora a baixa energia de superfície e grande estabilidade química do polímero tornem essa adesão um desafio a ser superado. Objetivo: Responder à pergunta: "Outros tratamentos de superfície do PEEK geram resistências de união superiores ao adesivo comercial?" Métodos: A busca foi feita nas bases Pubmed, , LILACS, Scopus, Web of Science, EMBASE, ProQuest e Google Scholar em junho de 2023 e não houve restrição relativa ao idioma ou à data de publicação dos estudos. Foram utilizados os seguintes termos e operadores booleanos: "polyether ether ketone" [MH] OR "polyether ether ketone" OR "polyetheretherketone" OR "polyetherketoneketone" OR "PEEK" AND "shear strength" [MH] OR "shear strength" OR "shear bond strength" OR "tensile bond strength" OR "shear" OR "tensile" OR "microtensile" OR "microshear" OR "bonding" OR "bond strength" OR "microtensile strength" OR "microshear bond strength" OR "bond" OR "adhesion" OR "bond integrity" OR "bonded" OR "Bonding Strength" OR "Bonding Behavior" OR "Adhesive Performance" OR " surface bonding" OR "tensile strength" [MH] OR "tensile strength". Foram incluídos exclusivamente estudos in vitro. Resinas compostas e resinas acrílicas foram consideradas como materiais de revestimento para PEEK. A média e o desvio padrão expressos em MPa e obtidos a partir de testes de cisalhamento e tração foram utilizados para relatar a resistência de união entre o PEEK e os materiais de revestimento. As meta-análises foram realizadas e a ferramenta Cochrane Collaboration avaliou o risco de viés (RoBDEMAT). Resultados: Foram selecionados 23 estudos. A resistência de união entre PEEK e resina composta foi favorecida pelo uso do adesivo (P<0,00001), independentemente do tipo de adesivo. O pré-tratamento com jato de areia Al2O3 (P<0,00001), ácido sulfúrico (P<0,00001), plasma frio (P=0,0006) e laser (P<0,00001) mostrou-se eficiente, embora o condicionamento com solução piranha não tenha tido efeito estatisticamente significativo (P=0,47). Conclusão: A aplicação de ácido sulfúrico antes do adesivo apresentou melhores resultados de resistência de união em comparação ao uso isolado do adesivo.

Polyether-ether-ketone (Polyetheretherketone - PEEK) is a polymer with excellent mechanical properties, which makes it a potential candidate to replace metallic alloys in several dental specialties. When used as an infrastructure for the manufacture of dental prostheses, the adhesion of PEEK to the aesthetic coating material is decisive for the longevity of the treatment, although the low surface energy and great chemical stability of the polymer make this adhesion a challenge to be overcome. Objective: Answer the question: "Do other PEEK surface treatments generate bond strengths superior to commercial adhesive?" Methods: The search was carried out in the Pubmed, LILACS, Scopus, Web of Science, and EMBASE, ProQuest and Google Scholar databases in June 2023 and there were no restrictions regarding the language or publication date of the studies. The following terms and bolean operators were used: "polyether ether ketone" [MH] OR "polyether ether ketone" OR "polyetheretherketone" OR "polyetherketoneketone" OR "PEEK" AND "shear strength" [MH] OR "shear strength" OR " shear bond strength" OR "tensile bond strength" OR "shear" OR "tensile" OR "microtensile" OR "microshear" OR "bonding" OR "bond strength" OR "microtensile strength" OR "microshear bond strength" OR "bond" OR "adhesion" OR "bond integrity" OR "bonded" OR "Bonding Strength" OR "Bonding Behavior" OR "Adhesive Performance" OR "surface bonding" OR "tensile strength" [MH] OR "tensile strength". Only in vitro studies were included. Composite resins and acrylic resins were considered as coating materials for PEEK. The mean and standard deviation expressed in MPa and obtained from shear and tensile tests were used to report the bond strength between PEEK and coating materials. Meta-analyses were performed and the Cochrane Collaboration tool assessed the risk of bias (RoBDEMAT). Results: 23 studies were selected. The bond strength between PEEK and composite resin was favored by the use of the adhesive (P<0,00001), regardless of the type of adhesive. Pretreatment with Al2O3 sandblasting (P<0,00001), sulfuric acid (P<0,00001), cold plasma (P=0,0006) and laser (P<0,00001) proved to be efficient, although conditioning with piranha solution did not have a statistically significant effect (P=0,47). Conclusion: The application of sulfuric acid before the adhesive showed better results in bond strength compared to the use of the adhesive alone.

Recobrimento da resina acrílica ativada termicamente com glaze e nanopartículas de ZnO e TiO2: estudo da ação antifúngica e de características mecânicas / Thermally activated acrylic resin coating with glaze and nanoparticles of ZnO and TiO2: study of antifungical action and mechanical characteristics

A resina acrílica é muito utilizada para a confecção de próteses removíveis parciais ou totais e apresenta uma grande interação com o meio bucal, além de possuir uma superfície que favorece o acúmulo de biofilme. Aplicação de materiais como glaze visam minimizar este efeito indesejável, através de uma ação que controle a formação de biofilme, muito embora esta ação ainda não seja tão efetiva. Neste sentido, o objetivo deste trabalho foi incorporar nanopartículas de dióxido de titânio e óxido de zinco, através da técnica de pulverização no glaze aplicado sob a superfície da resina acrílica ativada termicamente (RAAT), a fim de promover uma ação antimicrobiana. Para isso 4 grupos foram determinados: G: RAAT + glaze (controle); AlG: RAAT + glaze + óxido de alumínio (controle da rugosidade dos demais grupos); TiG: RAAT + glaze + dióxido de titânio; e ZnG: RAAT + glaze + óxido de zinco. Foram realizados testes de caracterização do material (DRX e MEV), teste de resistência a flexão com análise de Weibull e análise fractográfica, mensuração de cor e translucidez, perfilometria, goniometria, análise do efeito antibiofilme da Candida albicans e teste ANOVA um - fator. Os resultados obtidos mostraram que: não houve diferença estatística significante com relação a resistência mecânica destes grupos; existe uma diferença estatística significante na rugosidade, mensuração de cor e translucidez, do grupo controle quando comparado aos demais grupos; nos resultados de goniometria, os grupos com superfície tratada apresentaram maior molhamento, quando comparados com o grupo controle; e no teste de ação antifúngica, não foi possível perceber uma diferença estatística significante entre os grupos. Concluiu-se que a aplicação de nanopartículas melhora o molhamento superficial da resina, o que permite um melhor selamento periférico e uma maior retenção das próteses totais, muito embora não tenha proprocionado ação antifúngica para a metodologia proposta (AU).

Acrylic resin is widely used for the manufacture of partial or total removable prostheses and presents a great interaction with the oral environment, in addition to having a surface that favors the accumulation of biofilm. Application of materials such as glaze aim to minimize this undesirable effect, through an action that controls the biofilm formation, although this action is still not as effective. Therefore, the objective of this work was to incorporate nanoparticles of titanium dioxide and zinc oxide, through the spraying technique in the glaze applied under the surface of the thermally activated acrylic resin (RAAT), to promote an action antifungical. For this, 4 groups were determined: G: RAAT + glaze (control); AlG: RAAT + glaze + aluminum oxide (roughness control of the other groups); TiG: RAAT + glaze + titanium dioxide; and ZnG: RAAT + glaze + zinc oxide. Material characterization tests (DRX and SEM), flexural strength test with Weibull analysis and fractographic analysis, measurement of color and translucency, profilometry (roughness analysis), goniometry, antibiobilm analysis under the fungus C. albicans and ANOVA one ­ factor test. The results obtained showed that: there is no statistically significant difference regarding the mechanical resistance of these groups; there is a statistically significant difference in roughness, measurement of color and translucency, in the control group when compared to the other groups; in the goniometry results, the groups with treated surface showed greater wetting, when compared with the control group; and in the antifungical action test, it was not possible to perceive a statistically significant difference between the groups. It was concluded that the application of nanoparticles improves the surface wetting of the resin, which allows a better peripheral sealing and greater retention of complete dentures, although it did not determine antimicrobial action for the proposed methodology (AU).

Water Absorption Behavior of Oil Palm Empty Fruit Bunch (OPEFB) and Oil Palm Kernel Shell (OPKS) as Fillers in Acrylic Thermoplastic Composites.

In recent years, the use of oil palm wastes has been an interesting approach for the development of sustainable polymer matrix composites. Nevertheless, the water absorption behavior of these materials is one of the most critical factors for their performance over time. In this study, the water uptake characteristics of acrylic thermoplastic matrix composites reinforced separately with oil palm empty fruit bunch (OPEFB) and oil palm kernel shell (OPKS) were evaluated through immersion test in distilled water. The specimens of both composites were manufactured using the compression molding technique at three temperatures (80, 100, and 120 °C) using different particle sizes (425−600 and 600−850 µm). The composites, before and after the absorption test, were characterized by means of Fourier transform infrared spectroscopy, thermogravimetry, and scanning electron microscopy. The evaluation was complemented by the application of the Fickian diffusion model. Overall results showed that water absorption capacity decreased at a higher processing temperature and a larger particle size. In particular, it was observed that the type of reinforcement also influenced both water absorption and diffusivity. OPKS/acrylic and OPEFB/acrylic composites reached a maximum absorption of 77 and 86%, with diffusivities of 7.3 × 10−9 and 15.2 × 10−9 m2/min, respectively. Experimental evidence suggested that the absorption mechanism of the composites followed a non-Fickian model (n < 1.0).

Longitudinal Evaluation of Ethyl Cyanoacrylate Adhesives on Candida albicans Biofilm

ABSTRACT: The aim of this study is to evaluate the effect of two ethyl cyanoacrylate-based adhesives on the growth of Candida albicans biofilms on a heat-polymerized resin, after 7, 14, and 30 days of exposure. Ninety circular (10 x 2 mm) heat-polymerized resin specimens were equally divided into three groups: control, conventional ethyl cyanoacrylate (ECAc), and ethyl cyanoacrylate gel (ECAg). Two layers of 50 µL of each material were applied to the respective groups. C. albicans SC5314 strain was activated and standardized to 107 cells/mL-1. Specimens were immersed in 1 mL of artificial saliva and deposited in 1 mL fungal suspension, washed, and immersed in 1 mL of RPMI for 7, 14, and 30 days. The medium was changed at 48-hour intervals. The final suspension was diluted (10 -1 to 10-4) and deposited on Sabouraud dextrose agar for 48 h at 37 °C. After this period, the colonies were quantified using the CFU/mL calculation. Data were evaluated using one- way ANOVA and Tukey's test for post-hoc analysis (P=0.05). It was observed that both adhesives significantly reduced (P<0.05) biofilm formation compared to the control at all evaluated periods. In conclusion, an immediate and long-term inhibitory effect on C. albicans biofilm formation was observed.

RESUMEN: El objetivo del estudio fue evaluar el desarrollo microbiano en superficies de resina acrílica de termopolimerización, acondicionadas previamente, con adhesivos a base de etil cianoacrilato después de 7, 14 y 30 días de exposición en biofilm de Candida albicans. Noventa muestras circulares (10 x 2 mm) de resina acrílica de termopolimerización se dividieron por igual en tres grupos: control, etil cianoacrilato convencional (ECAc) y etil cianoacrilato en gel (ECAg). Se aplicaron dos capas de 50 µl de cada adhesivo en cada muestra. Simultáneamente, se activó la cepa C. albicans SC5314 y se estandarizó a 107 células/ml-1. Las muestras fueron sumergidas en 1 mL de saliva artificial por dos horas y luego se depositó 1 mL de suspensión fúngica por una hora. En seguida cada muestra se lavó y se sumergió en 1 mL de RPMI durante 7, 14 y 30 días, con cambios del medio a cada 48 horas. La suspensión final se diluyó (10-1 a 10-4) y se depositó en agar dextrose Sabouraud durante 48 h a 37° C. Después de este período, las colonias se cuantificaron mediante el cálculo de UFC / mL. Los datos obtenidos se evaluaron por medio del test ANOVA-one way y la prueba de Tukey para el análisis post- hoc (p = 0,05). Se observó que ambos adhesivos redujeron significativamente (P<0,05) la formación del biofilm de Candida albicans al ser comparados con el grupo control en todos los períodos evaluados. Los adhesivos a base de etil cianoacrilato poseen un efecto inhibidor de biofilm de Candida albicans de hasta 30 días, al ser aplicados dos veces en resinas acrílicas de termopolimerización.

Effect of silver-coated silica nanoparticles on the thermal conductivity of thermally activated acrylic resin / Efeito das nanopartículas de sílica revestidas por prata na condutividade térmica da resina acrílica ativada termicamente

Objective: Thermally activated acrylic resins (RAATs) are widely used in dentures as a base material due to their good dimensional stability and biocompatibility. However, their low thermal conductivity is a disadvantage, as it affects acceptance when using dental prostheses. Thus, the objective of this work was to measure the conduction heat in RAATs with and without incorporation of silica and silver nanoparticles (NP) and rigid reline (RR). Material and Methods: For this, samples were made and divided into 10 groups (n = 6). The first five groups were 2-mm-thick samples: G1 (RAAT control), G2 (RAAT + RR control), G3 (RAAT and NP + RR), G4 (RAAT + RR and NP), and G5 (RAAT and RR modified by NP). In the other five groups, 8-mm-thick samples were made: G6 (RAAT control), G7 (RAAT + RR control), G8 (RAAT and NP + RR), G9 (RAAT + RR and NP), and G10 (RAAT and RR modified by NP). The heat that cross the surface of the specimens was quantified using a wireless device. The data were submitted to two-factor ANOVA statistical analysis and Tukey ́s test with a 5% significance level. Results: After measuring the temperature variation as a function of time, it can be observed that there was a statistically significant difference for thermal conduction between the control groups and those modified with NP. Conclusion: Thus, it was possible to conclude that the NP improved the heat conduction in RAAT and in the RR because the nanoparticles have a higher thermal conductivity. (AU)

Objetivo: As resinas acrílicas termicamente ativadas (RAATs) são amplamente utilizada em próteses dentárias como material de base, pois possuem uma boa estabilidade dimensional e biocompatibilidade. Porém, como desvantagem, possuem baixa condutividade térmica, o que prejudica a aceitação do uso de próteses dentárias. Assim, o objetivo deste trabalho foi medir a condução de calor em RAAT com e sem incorporação de nanopartículas de sílica e prata (NP) e reembasador rígido (RR). Material e Métodos: Para isso, foram confeccionadas amostras que foram divididas em 10 grupos (n=6). Os primeiros cinco grupos eram amostras de 2 mm de espessura: G1 (RAAT controle), G2 (RAAT + RR controle), G3 (RAAT e NP + RR), G4 (RAAT + RR e NP) e G5 (RAAT e RR modificados por NP). E nos outros cinco grupos foram feitas amostras com espessura de 8 mm: G6 (RAAT controle), G7 (RAAT + RR controle), G8 (RAAT e NP + RR), G9 (RAAT + RR e NP) e G10 (RAAT e RR modificados por NP). O calor percorrido pela superfície dos corpos ­ de prova foi quantificado por meio de um dispositivo sem fio. Os dados foram submetidos à análise estatística ANOVA dois fatores e teste de Tukey com 5% de significância. Resultados: Após medir a variação da temperatura em função do tempo, pode-se observar que houve diferença estatisticamente significante para a condução térmica entre os grupos controle e os modificados com NP. Conclusão: Assim, foi possível concluir que a NP melhorou a condução de calor na RAAT e no RR, pois as nanopartículas apresentam maior condutividade térmica. (AU)

Comparación del módulo de elasticidad y resistencia de la resina acrílica de termocurado y la resina flexible superpoliamida. Estudio in vitro / Comparison of the module of elasticity and resistance of thermal curing acrylic resin and flexible superpolyamide resin. An in vitro study

Objetivo: Comparar el módulo de elasticidad y resistencia de la resina acrílica de termocurado y la resina flexible superpoliamida. Métodos: Se diseñó un estudio experimental que empleó dos tipos de resinas acrílicas preparadas en cera para obtener una forma rectangular de 64 mm de largo, 10 mm de ancho y 2,5 mm de grosor, pasadas a acrílico de termocurado y resina flexible superpoliamida. Se emplearon 10 bloques de resina acrílica de cada tipo sometidas a compresión por la máquina de ensayos universal, que generó una fuerza de aproximación de 0,001 N sobre los bloques con un avance de 0,01 mm/min. El módulo de resistencia y el módulo de elasticidad se analizaron mediante la prueba de flexión de tres puntos. Resultados: El módulo de elasticidad de la resina acrílica de termocurado fue de 2501,83 ± 139,42, mientras que el módulo de resistencia fue de 78,36 ± 11,69 MPa. Por otro lado, el módulo de elasticidad de la resina flexible superpoliamida fue de 1020,59 ± 92,95, mientras que el módulo de resistencia fue de 36,04 ± 2,71 MPa. El módulo de elasticidad de la resina acrílica de termocurado fue mayor al de la resina flexible superpoliamida, esta diferencia fue de 1481,24 MPa. El módulo de resistencia de la resina acrílica de termocurado fue mayor al de la resina flexible superpoliamida. Conclusiones: Se concluyó que el módulo de elasticidad (rigidez) y resistencia fue mayor en la resina acrílica de termocurado en comparación a la resina flexible superpoliamida(AU)

Objective: Compare the module of elasticity and resistance of thermal curing acrylic resin and flexible superpolyamide resin. Methods: An experimental study was conducted of two types of acrylic resins molded in wax to obtain a 64 mm long, 10 mm wide and 2.5 mm thick rectangular shape, and then transferred to thermal curing acrylic resin and flexible superpolyamide resin. Ten acrylic resin blocks of each type were used. The blocks were compressed by the universal testing machine, which generated an approximation force of 0.001 N on the blocks at a forward speed of 0.01 mm/min. The resistance module and the elasticity module were analyzed with the three point flexural test. Results: The elasticity module of the thermal curing acrylic resin was 2501.83 ± 139.42, whereas the resistance module was 78.36 ± 11.69 MPa. The elasticity module of the flexible superpolyamide resin was 1020.59 ± 92,95, whereas the resistance module was 36.04 ± 2.71 MPa. The elasticity module of the thermal curing acrylic resin was greater than that of the flexible superpolyamide resin, the difference being 1481.24 MPa. The resistance module of the thermal curing acrylic resin was greater than that of the flexible superpolyamide resin. Conclusions: The elasticity (rigidity) and resistance module was greater in the thermal curing acrylic resin than in the flexible superpolyamide resin(AU)

Effectiveness of Oil-Based Denture Dentifrices-Organoleptic Characteristics, Physicochemical Properties and Antimicrobial Action.

Denture dentifrices must be effective and not deleterious to prosthetic devices. This study formulated and evaluated dentifrices based on oils of Copaifera officinalis, Eucalyptus citriodora, Melaleuca alternifolia, Pinus strobus, and Ricinus communis. Organoleptic characteristics (appearance, color, odor, taste), physicochemical properties (pH, density, consistency, rheological, abrasiveness, weight loss, and surface roughness) and antimicrobial (Hole-Plate Diffusion-HPD)/anti-biofilm (Colony Forming Units-CFU) action against Staphylococcus aureus, Streptococcus mutans, and Candida albicans were evaluated. Formulations were compared with water (negative control) and a commercial dentifrice (positive control). The data were analyzed by Kruskal-Wallis and Dunn tests (α = 0.05). The organoleptic and physicochemical properties were adequate. All dentifrices promoted weight losses, with high values for C. officinalis and R. communis, and an increase in surface roughness, without differing from each other. For antimicrobial action, C. officinalis and E. citriodora dentifrices were similar to positive control showing effectiveness against S. mutans and C. albicans and no dentifrice was effective against S. aureus; regarding the anti-biofilm action, the dentifrices were not effective, showing higher CFU counts than positive control for all microorganisms. The dentifrices presented satisfactory properties; and, although they showed antimicrobial action when evaluated by HPD, they showed no effective anti-biofilm action on multispecies biofilm.

Comportamiento cromático de resinas acrílicas y bisacrílicas para restauraciones provisionales / Chromatic behavior of acrylic and bisacrylic resins used for provisional restorations

Introducción: Las prótesis provisionales son restauraciones usadas en prótesis fijas durante un tiempo, hasta la cementación de la prótesis definitiva. Uno de los problemas que presentan este tipo de restauraciones es el cambio de color, que afecta a la estética y, en consecuencia, produce sensación de desagrado en los pacientes. Objetivo: Evaluar, para restauraciones provisionales, con y sin el pulido final de la superficie, la estabilidad del color de dos resinas al ser sumergidas en café. Métodos: Estudio experimental in vitro, realizado en el Laboratorio de Prótesis de la Facultad de Odontología de la Universidad Nacional del Nordeste, Corrientes-Argentina, 2019. Se comparó una resina acrílica (Duralay®) con una bisacrílica (ProtempIV 3M®) para restauraciones provisionales. Se elaboraron 40 discos de resinas a partir de moldes metálicos de 25 mm de diámetro y 2 mm de espesor. Se utilizaron 20 discos para cada tipo de resina, de ellos, 10 pulidos y 10 sin pulir. Las muestras fueron almacenadas en agua destilada en estufa a 37 °C durante 24 h para hidratarlos. Luego se procedió a la toma del color. Con posterioridad, cada grupo se sumergió en café, manteniéndolos en estufa a 37 °C durante 24 h más. Seguidamente, se realizó la segunda toma del color. Se utilizó el colorímetro Kónica Minolta®, determinando la diferencia total de color ΔE. Para el análisis estadístico se utilizó ANOVA una vía y test de Tukey para identificar la diferencia entre grupos. Resultados: Se observó en el grupo de resina acrílica pulida una diferencia ΔE = 0,82 ± DS = 0,22 y de ΔE = 3,86 ± DS = 0,30 sin pulido. En el grupo de resina bisacrílica pulido se obtuvo ΔE = 4,84 ± DS = 0,25 y, para el no pulido, ΔE = 5,85 ± DS = 0,29. Conclusiones: Se comprobaron diferencias significativas en la estabilidad del color de ambas resinas. La resina bisacrílica fue la menos estable, independientemente del pulido(AU)

Introduction: Provisional prosthesis are restorations used in fixed prostheses for a while, until the definitive prosthesis is cemented. One of the problems posed by this type of restoration is the change in color, which affects esthetics and therefore creates a feeling of displeasure in patients. Objective: Evaluate, in the case of provisional restorations with and without final surface polish, the color stability of two resins when soaked in coffee. Methods: An in vitro experimental study was conducted in the Prosthesis Laboratory at the Dental School of the National University of the Northeast in Corrientes, Argentina, in the year 2019. A comparison was made of an acrylic resin (Duralay®) versus a bisacrylic resin (ProtempIV 3M®) for provisional restorations. Forty resin disks were made from metal molds 2 mm thick and 25 mm in diameter. Twenty disks were used for each type of resin, of which 10 were polished and 10 were not. The samples were stored in distilled water in a stove at 37ºC for 24 h to hydrate them. Color measurements were then taken. Next, each group was soaked in coffee and kept in the stove at 37ºC for another 24 h. A second color measurement was then taken. A Konica Minolta® colorimeter was used to determine total color difference ΔE. Statistical analysis was based on one-way ANOVA and Tukey's test was used to identify the difference between the groups. Results: In the polished acrylic resin group a difference was found of ΔE = 0.82 ± SD = 0.22, whereas in the non-polish group the difference was ΔE = 3.86 ± SD = 0.30. In the polished bisacrylic resin group the difference was ΔE = 4.84 ± SD = 0.25, whereas in the non-polish group the difference was ΔE = 5.85 ± SD = 0.29. Conclusions: Significant differences were found in the color stability of both resins. The bisacrylic resin was the least stable, regardless of polish(AU)

Properties of Acrylic Resin For CAD/CAM: A Systematic Review and Meta-Analysis of In Vitro Studies.

PURPOSE: This systematic review and meta-analysis of in vitro studies compared the prepolymerized acrylic resin used for CAD/CAM complete denture manufacturing versus the heat-polymerized acrylic resin for conventional complete dentures in terms of surface roughness, wettability, hardness and flexural strength. MATERIALS AND METHODS: An electronic search was performed in the PubMed, Embase, LILACS and Web of Science databases, without language or date restrictions. Gray literature and manual search tools were also used. The systematic review was carried out by two researchers independently, following the inclusion criteria: in vitro studies testing the CAD/CAM acrylic resin with a control group of heat-polymerized acrylic resin which compared at least one of the four material properties above. The meta-analysis was performed separately for each property, using a random effect model. RESULTS: Of the 914 studies found by means of search strategies, 698 were selected for the systematic review. After applying the eligibility criteria, only 17 articles were selected for the qualitative analysis in the systematic review; among these, 14 were included in the quantitative meta-analysis. The CAD/CAM prepolymerized acrylic resin in blocks had similar properties when compared to heat-polymerized acrylic resin in almost all outcome measures, with the exception of a statistically significant reduction in surface roughness. CONCLUSIONS: Based on the findings of this systematic review and meta-analysis, equally satisfactory results can be expected from dental prosthesis manufactured by the CAD/CAM system when compared to conventional ones, with the additional potential of reducing the pigmentation and attached microorganisms due to the reduced surface roughness of the prepolymerized resin.

Fibrin Biopolymer Incorporated with Antimicrobial Agents: A Proposal for Coating Denture Bases.

The characteristics of the denture base surface, in combination with the oral environment, promote the colonization and development of Candida albicans biofilm, which is the main cause of denture stomatitis. This study evaluated the effectiveness of fibrin biopolymer with digluconate chlorhexidine or Punica granatum alcoholic extract to prevent C. albicans biofilm. Conventional heat polymerized and pre-polymerized poly(methyl methacrylate) (PMMA) circular specimens (10 × 2 mm) were fabricated (n = 504) and randomly divided into groups: no treatment (control-CT), fibrin biopolymer coating (FB), fibrin biopolymer with P. granatum (FBPg), or digluconate of chlorhexidine (FBCh) coating. The specimens were inoculated with C. albicans SC5314 (1 × 107 cells/mL) and incubated for 24, 48, and 72 h. Crystal violet and colony-forming unit assays were used to quantify the total biofilm biomass and biofilm-living cells. A qualitative analysis was performed using confocal laser scanning microscopy. Data obtained are expressed as means and standard deviations and were statistically analyzed using a three-way analysis of variance (α = 0.05). The FBPg and FBCh groups inhibited the growth of C. albicans biofilm in both PMMA materials analyzed, with FBCh performing better in all periods evaluated (p < 0.0001). The colony forming unit (CFU) assay showed that the FB group favored the C. albicans biofilm growth at 24 h and 48 h (p < 0.0001), with no differences with CT group at 72 h (p = 0.790). All groups showed an enhancement in biofilm development up to 72 h (p < 0.0001), except the FBCh group (p = 0.100). No statistical differences were found between the PMMA base materials (p > 0.050), except in the FB group (p < 0.0001). Fibrin biopolymer, albeit a scaffold for the growth of C. albicans, when combined with chlorhexidine digluconate or P. granatum, demonstrated excellent performance as a drug delivery system, preventing and controlling the formation of denture biofilm.

Comparison of oral microbiome profile of polymers modified with silver and vanadium base nanomaterial by next-generation sequencing.

This study aimed to evaluate two methods of the incorporation of nanostructured silver vanadate decorated with silver nanoparticles (AgVO3) into acrylic resin and characterize the profile of early and late microbial communities in class and family taxonomic level by pyrosequencing. The specimens were made by adding different concentrations of AgVO3 (1, 2.5, and 5%) to the heat-activated acrylic resin by two methods: vacuum spatulation (VS) and polymeric film (PF). A control group (0%) without AgVO3 was also obtained for both methods. After 24 h and 7 days of incubation in human saliva, biofilm samples were collected, DNA was extracted, and 16S rRNA genes were sequenced by the 454-Roche sequencing platform. Seventeen classes and 51 families of bacteria were identified. The abundance of Bacteroidia, Bacilli, Negativicutes, Fusobacteria and Betaproteobacteria classes decreased after 7 days of incubation, and Clostridia, Gammaproteobacteria, and unclassified bacteria increased. The Negativicutes and Betaproteobacteria classes were more abundant when the PF method was used, and Gammaproteobacteria was more abundant when VS was used. The incorporation of 5% AgVO3 promoted a reduction in the prevalence of Bacilli, Clostridia, Negativicutes, Betaproteobacteria, and unclassified bacteria, and increased Gammaproteobacteria. The addition of AgVO3 to acrylic resin altered the early and mature microbiome formed on the specimen surface, and the PF method presented a more favorable microbial profile than the VS method.

Surface roughness of acrylic resins used for denture base after chemical disinfection: A systematic review and meta-analysis.

OBJECTIVE: This study aimed to systematically review the literature regarding the surface roughness of polymethylmethacrylate (PMMA) for denture bases, disinfected with different chemical agents and analyse the outcomes of the included studies. BACKGROUND: Various chemical disinfection protocols to clean the removable dental prosthesis are reported in the literature, however systematic reviews analysing the outcomes in the surface roughness of the PMMA are lacking. METHODS: The Preferred Reporting Items for Systematic Review and Meta-Analyses (PRISMA) checklist was used to structure this systematic review. The inclusion criteria were as follows: clinical trials, in vitro studies, studies in English and studies comparing the effects of chemical disinfection products on the surface roughness of PMMA. An electronic search was performed in the following databases: PubMed/MEDLINE, Scopus and Web of Science.; we also conducted a manual search for articles published in specific journals of dental prostheses and dental materials. RESULTS: Thirteen in vitro studies in this systematic review and meta-analysis. According to the meta-analysis, the effects of 0.5% (P = .32; MD: 0.06; CI: -0.05 to 0.17; heterogeneity: P < .00001; I2  = 92%) and 1% NaOCl solutions (P = .27; MD: 0.01; CI: -0.01. to 0.03; heterogeneity: P = .03; I2  = 55%) did not statistically differ between the groups studied. Effects of alkaline peroxide were statistically significant (P = .0009; MD: 0.01; CI: 0.01-0.02; heterogeneity: P = .004; I2  = 65%), suggesting that it promotes deterioration of the PMMA surface. CONCLUSION: The alkaline peroxide, when used as a disinfectant, generated changes on the surface roughness of PMMA and should be used with caution; however, NaOCl, even at different concentrations, caused fewer changes on the surface of the denture base.

Antifungal biomaterial for reducing infections caused by Candida albicans in edentulous patients.

INTRODUCTION: Polymethylmethacrylate (PMMA) acrylic resins are used to make dentures for edentulous patients. OBJECTIVE: To find out the prevalence of Candida species in patients with and without removable prostheses from a dental clinic in León, Guanajuato, as well as to assess the antifungal effect and biological behavior of an experimental PMMA with silver nanoparticles for its possible application in prostheses. METHOD: To identify Candida species, smear samples were obtained from the palatal mucosa of 140 patients aged ≥ 60 years. The experimental PMMA with silver nnoparticles was placed in Candida albicans cultures, which were stained with the Live/Dead® kit for analysis under confocal microscopy; subsequently, it was implanted in Wistar rats in order to know its behavior in the surrounding tissues. RESULTS: Candida albicans was the most prevalent species in the evaluated patients, followed by Candida tropicalis and Candida krusei. The acrylic resin with silver nanoparticles significantly decreased the presence of Candida albicans. In the animal model, a discrete and controlled inflammatory reaction was found, which indicated biocompatibility of the acrylic resin that was used. CONCLUSIONS: It is possible for the nanostructured material with antifungal effect to be used in order to promote the reduction of oral Candida infections in edentulous patients.

INTRODUCCIÓN: Las resinas acrílicas de polimetilmetacrilato (PMMA) son utilizadas para elaborar dentaduras para pacientes edéntulos. OBJETIVO: Conocer la prevalencia de las especies de Candida en pacientes con y sin prótesis removibles de una clínica de odontología en León, Guanajuato; así como valorar el efecto antifúngico y el comportamiento biológico de un PMMA experimental con nanopartículas de plata para su posible aplicación en prótesis. MÉTODO: Para identificar las especies de Candida se obtuvieron muestras para frotis de la mucosa palatina de 140 pacientes con edad ≥ 60 años. El PMMA experimental con nanopartículas de plata fue colocado en cultivos de Candida albicans, los cuales fueron teñidos con el kit Live/Dead® para su análisis bajo microscopia confocal; posteriormente, se implantó en ratas Wistar para conocer su comportamiento en los tejidos circundantes. RESULTADOS: Candida albicans fue la especie más prevalente en los pacientes valorados, seguida de Candida tropicalis y Candida krusei. La resina acrílica con nanopartículas de plata disminuyó significativamente la presencia de Candida albicans. En el modelo animal se encontró reacción inflamatoria discreta y controlada, lo cual indicó la biocompatibilidad de la resina acrílica utilizada. CONCLUSIONES: Es posible utilizar el material nanoestructurado con efecto antifúngico para promover la reducción de infecciones orales por Candida en pacientes edéntulos.