Are we approaching the development of a novel calcium phosphate-based bioceramic dental material?

OBJECTIVES: Develop a sustainable bovine hydroxyapatite dental ceramic with the addition of titanium dioxide (TiO2) nanoparticles (5 % and 8 % by weight), analyzing the outcome of this addition to the microstructure, as well as its mechanical and chemical properties, in order to evaluate whether they satisfy the International Organization for Standardization (ISO) 6872:2015 for dental ceramics or not. METHODS: Disks were obtained through uniaxial followed by isostatic pressing from bovine hydroxyapatite powder and TiO2 nanoparticles and sintered at 1300ºC for 2 h. Three experimental groups were developed (HA, HA+5 %TiO2 and HA+8 %TiO2) and subjected to X-ray diffraction (XRD), scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), indentation fracture (IF), biaxial flexural strength (BFS) and chemical solubility test. RESULTS: XRD revealed, for HA group, the appearance of a peak corresponding to b-tricalcium phosphate (ß-TCP). For HA+ 5 %TiO2 and HA+ 8 %TiO2, the entire composition was converted into ß-TCP and calcium titanate (CaTiO3). The SEM images showed a dense ceramic matrix and a uniform distribution of another phase in groups with TiO2 nanoparticles. HA+ 5 %TiO2 (1.40 ± 0.18 MPa.m1/2) and HA+ 8 %TiO2 (1.32 ± 0.18 MPa.m1/2) showed significantly higher fracture toughness values than HA (0.67 ± 0.09 MPa.m1/2). HA showed significantly higher characteristic stress (295.8 MPa) in comparison to groups with 5 % (235.1 MPa) and 8 % (214.4 MPa) TiO2 nanoparticles. Differences were not observed between the Weibull modulus values. The solubility results indicated that all experimental ceramics were above the 2000 ug/cm2 limit set by the ISO 6872:2015. SIGNIFICANCE: This study proposed the development and characterization of a new ceramic for dental prosthesis made from HA extracted from bovine bones, with the intention of reusing these solids waste and transforming them into a sustainable and low-cost material. Although the experimental calcium phosphate ceramic with additions of 5 % and 8 % of TiO2 achieved desirable mechanical properties, the chemical solubility values were very high.

Development of a new biomaterial based on cashew tree gum (Anarcadium occidentale L.) enriched with hydroxyapatite and evaluation of cytotoxicity in adipose-derived stem cell cultures.

Cashew tree gum is a polysaccharide material highly available in the Northeast region of Brazil. It has been explored for biocompatibility with human tissues. This research aimed to describe the synthesis and characterization of cashew gum/hydroxyapatite scaffold and evaluate the possible cytotoxicity in murine adipose-derived stem cells (ADSCs) cultures. ADSCs of the subcutaneous fat tissue of Wistar rats were collected, isolated, expanded, differentiated into three strains, and characterized immunophenotypically. The scaffolds were synthesized through chemical precipitation, lyophilized and characterized through scanning electron microscopy (SEM), infrared spectroscopy (FTIR), X-ray diffraction (XRD), thermal analysis (TG and DTG), and mechanical testing. The scaffold presented a crystalline structure and pores with an average diameter of 94.45 ± 50.57 µm. By mechanical tests, the compressive force and modulus of elasticity were like the cancellous bone. The isolated adipose-derived stem cells (ADSCs) presented fibroblast morphology, adhesion capacity to plastic, differentiation in osteogenic, adipogenic and chondrogenic lineages, positive expression for the CD105 and CD90 markers and negative expression for the CD45 and CD14 markers. The MTT test showed increased cell viability, and the biomaterial showed a high level of hemocompatibility (<5 %). This study allowed the development of a new scaffold for future surgical applicability in tissue regeneration.

Fabrication and characterization of a bioactive polymethylmethacrylate-based porous cement loaded with strontium/calcium apatite nanoparticles.

Polymethylmethacrylate (PMMA)-based cements are used for bone reparation due to their biocompatibility, suitable mechanical properties, and mouldability. However, these materials suffer from high exothermic polymerization and poor bioactivity, which can cause the formation of fibrous tissue around the implant and aseptic loosening. Herein, we tackled these problems by adding Sr2+ -substituted hydroxyapatite nanoparticles (NPs) and a porogenic compound to the formulations, thus creating a microenvironment suitable for the proliferation of osteoblasts. The NPs resembled the structure of the bone's apatite and enabled the controlled release of Sr2+ . Trends in the X-ray patterns and infrared spectra confirmed that Sr2+ replaced Ca2+ in the whole composition range of the NPs. The inclusion of an effervescent additive reduced the polymerization temperature and lead to the formation of highly porous cement exhibiting mechanical properties comparable to the trabecular bone. The formation of an opened and interconnected matrix allowed osteoblasts to penetrate the cement structure. Most importantly, the gas formation confined the NPs at the surface of the pores, guaranteeing the controlled delivery of Sr2+ within a concentration sufficient to maintain osteoblast viability. Additionally, the cement was able to form apatite when immersed into simulated body fluids, further increasing its bioactivity. Therefore, we offer a formulation of PMMA cement with improved in vitro performance supported by enhanced bioactivity, increased osteoblast viability and deposition of mineralized matrix assigned to the loading with Sr2+ -substituted hydroxyapatite NPs and the creation of an interconnected porous structure. Altogether, our results hold promise for enhanced bone reparation guided by PMMA cements.

Development and characterization of poultry collagen-based hybrid hydrogels for bone regeneration

Purpose: Poultry by-products can contribute as an innovative natural source for the development of composites based on polymers and minerals aiming at bone regeneration. The objective of this study was the physicochemical and biological characterization of collagen-based hydrogels crosslinked with ultraviolet (UV)-riboflavin. Methods: Pure hydrogels of 100% collagen (G1) or hybrid hydrogels, 90% collagen:10% apatite (G2), 90% collagen:10% nanokeratin (G3), and 90% collagen:5% apatite:5% nanokeratin (G4) were characterized by scanning electron microscope, Fourier-transform infrared spectroscopy, differential scanning calorimetry, swelling degree and quali-quantitative histological analysis. Ectopic implantation in subcutaneous tissue in mice at one, three and nine weeks allowed to assess the inflammation (neutrophils, lymphocytes, macrophages, and giant cells) and repair (neovascularization, and connective tissue) to determine biocompatibility and the integrity of biomaterials to score their biodegradability. Histomorphometry on critical size defects in rat calvaria at one and three months evaluated the percentage of bone, connective tissue, and biomaterials in all groups. Results: The hydrogels presented porous microstructure, water absorption and physicochemical characteristics compatible with their polymeric and/or mineral composition. All materials exhibited biocompatibility, biodegradability, and low osteoconductivity. G2 showed greater density of new bone and biomaterial than the G1, G3 and G4. Conclusions: The collagen-apatite group formulation suggests potential for development as osteopromoting membrane.