Functional and structural assessment of an experimental section gap graded modified with sugarcane bagasse ash.

Gap-graded aggregate combined with asphalt rubber presents a high-performance alternative for roads with heavy traffic loads, offering advantages over conventional mixtures in terms of permanent deformation (rutting), fatigue life, and texture. In this study, the conventional filler in the well-established mixture was substituted with sugarcane bagasse bottom ash (SCBA) at a proportion of 5% of the total mineral aggregates. The objective was to enhance the mechanical performance of the asphalt coating while ensuring proper disposal of this waste material. Compared to conventional filler, SCBA is less dense, has smaller dimensions, and exhibits greater roughness, thereby affecting the volumetric parameters of the Marshall mix design. Consequently, the volume of voids in mineral aggregates and voids filled with asphalt increased while maintaining the same volume of air voids (5.3%). Consequently, there was a notable increase in Marshall Stability (40%) and Indirect Tensile Test (22%) mechanical parameters. Following laboratory analysis, the modified mixtures were applied as asphalt coating on a high-traffic highway (BR-158). Field specimens revealed an 18% increase in the Resilience Modulus (4088 MPa; 3478 MPa). Additionally, its Flow Number exhibited a 73% increase (16,707; 9681), and its permanent deformation rate was 28% lower within 10,000 cycles in the dynamic creep test. This was further supported by an 11% reduction in permanent deformation rate in the Hamburg Wheel Tracking Device (HWTD) within 20,000 cycles (3.2 mm; 3.6 mm). In conclusion, the partial replacement of conventional filler with sugarcane bagasse ash within the established granulometric range has demonstrated technical feasibility both in laboratory and field settings.

Machine learning for the adsorptive removal of ciprofloxacin using sugarcane bagasse as a low-cost biosorbent: comparison of analytic, mechanistic, and neural network modeling.

Contamination with traces of pharmaceutical compounds, such as ciprofloxacin, has prompted interest in their removal via low-cost, efficient biomass-based adsorption. In this study, classical models, a mechanistic model, and a neural network model were evaluated for predicting ciprofloxacin breakthrough curves in both laboratory- and pilot scales. For the laboratory-scale (d = 2.2 cm, Co = 5 mg/L, Q = 7 mL/min, T = 18 °C) and pilot-scale (D = 4.4 cm, Co = 5 mg/L, Q = 28 mL/min, T = 18 °C) setups, the experimental adsorption capacities were 2.19 and 2.53 mg/g, respectively. The mechanistic model reproduced the breakthrough data with high accuracy on both scales (R2 > 0.4 and X2 < 0.15), and its fit was higher than conventional analytical models, namely the Clark, Modified Dose-Response, and Bohart-Adams models. The neural network model showed the highest level of agreement between predicted and experimental data with values of R2 = 0.993, X2 = 0.0032 (pilot-scale) and R2 = 0.986, X2 = 0.0022 (laboratory-scale). This study demonstrates that machine learning algorithms exhibit great potential for predicting the liquid adsorption of emerging pollutants in fixed bed.

Sugarcane bagasse derived xylooligosaccharides produced by an arabinofuranosidase/xylobiohydrolase from Bifidobacterium longum in synergism with xylanases.

Arabinoxylan is a major hemicellulose in the sugarcane plant cell wall with arabinose decorations that impose steric restrictions on the activity of xylanases against this substrate. Enzymatic removal of the decorations by arabinofuranosidases can allow a more efficient arabinoxylan degradation by xylanases. Here we produced and characterized a recombinant Bifidobacterium longum arabinofuranosidase from glycoside hydrolase family 43 (BlAbf43) and applied it, together with GH10 and GH11 xylanases, to produce xylooligosaccharides (XOS) from wheat arabinoxylan and alkali pretreated sugarcane bagasse. The enzyme synergistically enhanced XOS production by GH10 and GH11 xylanases, being particularly efficient in combination with the latter family of enzymes, with a degree of synergism of 1.7. We also demonstrated that the enzyme is capable of not only removing arabinose decorations from the arabinoxylan and from the non-reducing end of the oligomeric substrates, but also hydrolyzing the xylan backbone yielding mostly xylobiose and xylose in particular cases. Structural studies of BlAbf43 shed light on the molecular basis of the substrate recognition and allowed hypothesizing on the structural reasons of its multifunctionality.

Characterization of sugarcane bagasse solubilization and utilization by thermophilic cellulolytic and saccharolytic bacteria at increasing solid loadings.

In Brazil the main feedstock used for ethanol production is sugarcane juice, resulting in large amounts of bagasse. Bagasse has high potential for cellulosic ethanol production, and consolidated bioprocessing (CBP) has potential for lowering costs. However, economic feasibility requires bioprocessing at high solids loadings, entailing engineering and biological challenges. This study aims to document and characterize carbohydrate solubilization and utilization by defined cocultures of Clostridium thermocellum and Thermoanaerobacterium thermosaccharolyticum at increasing loadings of sugarcane bagasse. Results show that fractional carbohydrate solubilization decreases as solids loading increases from 10 g/L to 80 g/L. Cocultures enhance solubilization and carbohydrate utilization compared to monocultures, irrespective of initial solids loading. Rinsing bagasse before fermentation slightly decreases solubilization. Experiments studying inhibitory effects using spent media and dilution of broth show that negative effects are temporary or reversible. These findings highlight the potential of converting sugarcane bagasse via CBP, pointing out performance limitations that must be addressed.

Unlocking Agronutrient Resources: Sorption Strategies for sugar-energy industry waste.

Vinasse and ash from sugarcane bagasse (SCB) are key byproducts in the sugar-energy industry. Vinasse is nutrient-rich but environmentally challenging, while sugarcane bagasse ash (SCBA) offers excellent adsorbent for treating effluents. This work aims to assess the effectiveness of SCBA in removing nitrogen (N) and potassium (K) nutrients from Vinasse. Simulated standard solutions of K2SO4 and (NH4)2HPO4 were used to mimic the nutrient concentrations in Vinasse and optimize experimental parameters such as adsorbent mass and contact time. Kinetic and isotherm models were also applied to elucidate the underlying adsorption mechanisms. Structural, morphological, and thermal analyses revealed the micro-mesoporous and heterogeneous nature of SCBA, primarily composed of SiO2 (quartz and cristobalite). The sorption assessment indicated the ideal conditions involved lower SCBA masses (2.5 g) and 6 h of contact time for the simulated standard solutions. The replicated conditions for Vinasse (at an adjusted sorption time of 24 h) demonstrated nutrient sorption and pH correction of the Vinasse, attributed to the alkaline nature of SCBA. Analysis of the sorption kinetic models for K+ and NH4+ revealed that SCBA interacts diffusively with the environment, not necessarily controlled by adsorption on active sites, indicating non-uniform characteristics. The sorption isotherms for K+ and NH4+ showed the non-linearized Freundlich model was the most suitable, indicating the adsorption sites with varying energy levels and a multilayer sorption process. In conclusion, we successfully demonstrated the sorption of nutrients from Vinasse by SCBA, enhancing the value of these residues and mitigating their environmental impact when used in agricultural applications.

Hydrothermal co-liquefaction of microalgae, sugarcane bagasse, brewer's spent grain, and sludge from a paper recycling mill: Modeling and evaluation of biocrude and biochar yield.

Biomass can be used as an energy source to thermochemical conversion processes to biocrude production. However, the supply and dependence on only one biomass for biocrude production can be an obstacle due to its seasonality, availability, and logistics costs. In this way, biomass waste and agroindustrial residues can be mixture and used as feedstock to the hydrothermal co-liquefaction (co-HTL) process as an alternative to obtaining biocrude. In this sense, the present paper analyzed the biocrude yield influence of the co-HTL from a quaternary unprecedented blend of different biomasses, such as sugarcane bagasse, brewer's spent grain (BSG), sludge from a paper recycling mill (PRM), and microalgae (Chlorella vulgaris). In this way, a simplex lattice design was employed and co-HTL experiments were carried out in a 2000 mL high-pressure stirred autoclave reactor under 275 °C for 60 min, considering 15% of feedstock/water ratio. Significant effects in each feedstock and their blends were analyzed aiming to increase biocrude and biochar yield. It was found that the addition of microalgae is only significant when considered more than 50% into the blend with BSG and PRM sludge to increase biocrude yield.

New blend of renewable bioplastic based on starch and acetylated xylan with high resistance to oil and water vapor.

Renewable materials of biological origin exhibit attractive properties in relation to traditional plastics, as they can be partially or completely replaced, thereby reducing environmental impacts. Hemicelluloses are a group of polysaccharides that have expanded applications when acetylated. Acetylation can improve the mechanical strength and water vapor barrier properties of xylan-based bioplastics. By partially acetylating xylan in the present study, it was possible to use water as a solvent for the film-forming solution and starch as a second polysaccharide in the formation of bioplastics. Xylan was modified via partial chemical acetylation by varying the reaction time, solvent, and catalyst content. The bioplastics were formed by non-acetylated xylan and acetylated xylan with degrees of substitution (DS) of 0.45 and 0.9, respectively, with starch to form blends using glycerol as a plasticizer. Acetylation with DS 0.45 showed better results in increasing the hydrophilicity of the bioplastic. On the other hand, acetylation influenced the thermal stability of bioplastics, increasing the maximum temperature of the degradation rate from 302 °C to 329 °C and 315 °C, owing to changes in the crystallinity of the polymers. In addition to the modulus of elasticity 2.99 to 290.61 and 274.67 MPa for the non-acetylated bioplastic and the bioplastic with DS of 0.45 and 0.90, respectively. Thus, the films obtained presented suitable physicochemical properties for use in various industrial applications, such as active and intelligent packaging in the food sector.

Modulating the properties and structure of lignins produced by alkaline delignification of sugarcane bagasse pretreated with two different mineral acids at pilot-scale.

Sugarcane bagasse was pretreated with dilute phosphoric acid or sulfuric acid to facilitate cellulose hydrolysis and lignin extraction. With phosphoric acid, only 8 % of the initial cellulose was lost after delignification, whereas pretreatment with sulfuric acid resulted in the solubilization of 38 % of the initial cellulose. After enzymatic hydrolysis, the process using phosphoric acid produced approximately 35 % more glucose than that using sulfuric acid. In general, the lignins showed 95-97 % purity (total lignin, w/w), an average molar mass of 9500-10,200 g mol-1, a glass transition temperature of 140-160 °C, and a calorific value of 25 MJ kg-1. Phosphoric acid lignin (PAL) was slightly more polar than sulfuric acid lignin (SAL). PAL had 13 % more oxidized units and 20 % more OH groups than SAL. Regardless of the acid used, the lignins shared similar properties, but differed slightly in the characteristics of their functional groups and chemical bonds. These findings show that pretreatment catalyzed with either of the two acids resulted in lignin with sufficiently good characteristics for use in industrial processes.

Comparative analysis of Chrysoporthe cubensis exoproteomes and their specificity for saccharification of sugarcane bagasse.

The phytopathogenic fungus Chrysoporthe cubensis is a relevant source of lignocellulolytic enzymes. This work aimed to compare the profile of lignocellulose-degrading proteins secreted by C. cubensis grown under semi-solid state fermentation using wheat bran (WB) and sugarcane bagasse (SB). The exoproteomes of the fungus grown in wheat bran (WBE) and sugarcane bagasse (SBE) were qualitative and quantitatively analyzed by liquid chromatography-electrospray ionization tandem mass spectrometry (LC-ESI-MS/MS). Data are available via ProteomeXchange with identifier PXD046075. Label-free proteomic analysis of WBE and SBE showed that the fungus produced a spectrum of carbohydrate-active enzymes (CAZymes) with exclusive characteristics from each extract. While SBE resulted in an enzymatic profile directed towards the depolymerization of cellulose, the enzymes in WBE were more adaptable to the degradation of biomass rich in hemicellulose and other non-lignocellulosic polymers. Saccharification of alkaline pre-treated sugarcane bagasse with SBE promoted glucose release higher than commercial cocktails (8.11 g L-1), while WBE promoted the higher release of xylose (5.71 g L-1). Our results allowed an in-depth knowledge of the complex set of enzymes secreted by C. cubensis responsible for its high lignocellulolytic activity and still provided the identification of promising target proteins for biotechnological applications in the context of biorefinery.

Fermentative Production of ß-Carotene from Sugarcane Bagasse Hydrolysate by Rhodotorula glutinis CCT-2186.

Β-Carotene is a red-orange pigment that serves as a precursor to important pharmaceutical molecules like vitamin A and retinol, making it highly significant in the industrial sector. Consequently, there is an ongoing quest for more sustainable production methods. In this study, glucose and xylose, two primary sugars derived from sugarcane bagasse (SCB), were utilized as substrates for ß-carotene production by Rhodotorula glutinis CCT-2186. To achieve this, SCB underwent pretreatment using NaOH, involved different concentrations of total solids (TS) (10%, 15%, and 20%) to remove lignin. Each sample was enzymatically hydrolyzed using two substrate loadings (5% and 10%). The pretreated SCB with 10%, 15%, and 20% TS exhibited glucose hydrolysis yields (%wt) of 93.10%, 91.88%, and 90.77%, respectively. The resulting hydrolysate was employed for ß-carotene production under batch fermentation. After 72 h of fermentation, the SCB hydrolysate yielded a ß-carotene concentration of 118.56 ± 3.01 mg/L. These findings showcase the robustness of R. glutinis as a biocatalyst for converting SCB into ß-carotene.

Analysis of the Mechanical Properties of a Stabilized Subgrade Type Soil under a Sustainable Approach for Construction.

This article presents an experimental study to analyze the mechanical properties of a soil stabilized with ordinary Portland cement (OPC) under a sustainable approach consisting of a significant substitution of OPC for sugarcane bagasse ash (SCBA) to reduce the quantity of cement used in the stabilization, reaching the necessary mechanical requirements for its use as a subgrade layer. Soil specimens were elaborated with 3%, 5%, and 7% OPC as a stabilizing agent by weight of the soil. These mixtures were then partially substituted with 25%, 50%, and 75% SCBA, with these percentages being by weight of the stabilizer (OPC). Compaction, compressive strength, and California bearing ratio (CBR) tests were performed to evaluate the mechanical properties of the specimens. The results indicate that a 25% substitution of OPC by SCBA shows a similar performance to the mixture with only Portland cement, so a reduction in OPC use can be made. Further, with a substitution of 100% OPC by SCBA, the CBR of natural soil without stabilizers is improved.

Sugarcane Bagasse Ash as an Alternative Source of Silicon Dioxide in Sodium Silicate Synthesis.

To reduce the environmental impacts from sodium silicate synthesis, a ceramic method was suggested, with sugarcane bagasse ash (SCBA) as the source of silicon dioxide and sodium carbonate. Although the production of sodium silicate is carried out on a large scale, it should be noted that its process requires temperatures above 1000 °C; it also requires the use of highly corrosive agents such as sodium hydroxide and chlorine gas to neutralize the remaining sodium hydroxide. In the present study, the synthesis temperatures were reduced to 800 °C with a reaction time of 3 h by pressing equimolar mixtures of previously purified SCBA and sodium carbonate; then, heat treatment was carried out under the indicated conditions. The resulting materials were analyzed with Fourier transform infrared spectroscopy (FTIR) and X-ray diffraction (XRD). Among the crystalline phases, calcium disodium silicate was identified, in addition to sodium silicate; thus, it was inferred that the other components of the ash can interfere with the synthesis of silicate. Therefore, in order to obtain the highest composition of sodium silicate, a leaching treatment of the SCBA is required.

Enzymatic potential of endophytic fungi: xylanase production by Colletotrichum boninense from sugarcane biomass.

Endophytic fungi constitute a major part of the still unexplored fungal diversity and have gained interest as new biological sources of natural active compounds, including enzymes. Endophytic fungi were isolated from soybean leaves and initially screened on agar plates for the production of CMCase (carboxymethylcellulase), xylanase, amylase and protease. The highest Enzymatic Indexes (IE) were verified for xylanase (2.14 and 1.31) with the fungi M6-A6P5F2 and M12-A5P3F1.2 and CMCase (1.92 and 1.62) with the fungi M13-A9P2F1 and M12-A5P3F1.2, respectively. The production of xylanase and CMCase by the selected fungi was evaluated in submerged cultivation using beechwood xylan and carboxymethylcellulose (CMC), as well as sugarcane straw and bagasse in different ratios as carbon sources. Both types of lignocellulosic biomass proved to be good inducers of enzymatic activity. The best xylanase producer among the isolates was identified as Colletotrichum boninense. With this fungus, the highest xylanase activity was obtained with a sugarcane straw-bagasse mixture in a 50:50 ratio (383.63 U mL-1), a result superior to that obtained with the use of beechwood xylan (296.65 U mL-1). Regardingthe kinetic behavior of the crude xylanase, there was found optimal pH of 5.0 and optimal temperatures of 50°C and 60°C. At 40°C and 50°C, xylanase retained 87% and 76% of its initial catalytic activity, respectively. These results bring new perspectives on bioprospecting endophytic fungi for the production of enzymes, mainly xylanase, as well as the exploitation of agro-industrial by-products, such as sugarcane straw and bagasse.

Trichoderma longibrachiatum and thermothelomyces thermophilus co-culture: improvement the saccharification profile of different sugarcane bagasse varieties.

OBJECTIVES: The aim of the present work was to perform the co-culture between Trichoderma longibrachiatum LMBC 172, a mesophilic fungus, with Thermothelomyces thermophilus LMBC 162, a thermophilic fungus, by submerged fermentation in a bioreactor. RESULTS: There was an increase in protein production, reaching the value of 35.60 ± 3.76 µg/ml at 72 h. An increase in the amount of proteins of 27.5% in relation to the isolated cultivation of T. longibrachiatum and 19.7% in comparison when T. thermophilus was isolated and cultivated. After that, the saccharification profile of three varieties of sugarcane (sugarcane in natura, culms of sugarcane SP80-3280, and culms of Energy cane) submitted in two pretreatments (autohydrolysis and chemical) was performed. The (e) chemical pretreatment was the better in generating of fermentable sugars from sugarcane bagasse and culms of Energy cane, while with the autohydrolysis pretreatment was obtained the better values to culms of SP80-3280 sugarcane. The sugars found were glucose, xylose, arabinose, and cellobiose. CONCLUSION: These results suggest that the co-culture between these microorganisms has the potential to produce an enzymatic cocktail with high performance in the hydrolysis of materials from the sugar-alcohol industry.

Eco-friendly synthesis of a novel adsorbent from sugarcane and high-pressure boiler water.

The development of industrial process in line with the circular economy and the environmental, social and corporate governance (ESG) is the foundation for sustainable economic development. Alternatives that make feasible the transformation of residues in added value products are promising and contribute to the repositioning of the industry towards sustainability, due to financial leverage obtained from lesser operational costs when compared with conventional processes, therefore increasing the company competitivity. In this study, it is presented a promising and innovative technology for the recycling of agro-industrial residues, the sugarcane bagasse and the high-pressure water boiler effluent, in the development of a low-cost adsorbent (HC-T) using the hydrothermal carbonization processes and its application in the adsorption of herbicide Diuron and Methylene Blue dye from synthetic contaminated water. The hydrothermal carbonization was performed in a Teflon contained inside a sealed stainless-steel reactor self-pressurized at 200°C, biomass-to-effluent (m/v) ratio of 1:3 and 24 h. The synthesized material (HC) was activated in an oven at 450°C for 10 min, thus being named adsorbent (HC-T) and characterized by textural, structural and spectroscopic analyses. The low-cost adsorbent HC-T presented an 11-time-fold increase in surface area and ∼40% increase in total pore volume in comparison with the HC material. The kinetic and isotherm adsorption experiment results highlighted that the HC-T was effective as a low-cost adsorbent for the removal of herbicide Diuron and Methylene Blue dye from synthetic contaminated waters, with an adsorption capacity of 35.07 (63.25% removal) and 307.09 mg g-1 (36,47% removal), respectively.

Improvement of enzymatic saccharification by simultaneous pulping of sugarcane bagasse and washing of its cellulose fibers in a batch reactor.

A modification of the conventional batch organosolv process is proposed in a way where the solid biomass remains inside a basket, physically separated from the liquid phase, with the vapor promoting the fractionation of the biomass and the extracted compounds and fragments being washed down to the liquid phase. The modified organosolv process applied to sugarcane bagasse (SB-M) delivers a rich cellulosic solid phase that after enzymatic hydrolysis leads to a hydrolyzed with approximately 100 g L-1 of glucose. At the same enzymatic hydrolysis conditions, the conventional organosolv process (SB-C) delivers a hydrolyzed with 80 g L-1 of glucose, while the autohydrolysis process (SB-A) leads to 55 g L-1 of glucose. These different results are related to the cellulose content: SB-M (70%), SB-C (57%), e SB-A (44%), as well the reduced lignin content in the SB-M. The novelty of this study is the confirmation that it is possible to degrade lignin from sugarcane bagasse and simultaneously remove its fragments from the cellulose fibers in a batch reactor containing an internal basket. This study describes a simple and rapid protocol for the isolation of the main components of lignocellulosic biomass (cellulose, hemicellulose, and lignin), which may lead to the study of new catalysts for the chemical transformation of these components separately or simultaneously to the step of pretreatment.

Production of recombinant lytic polysaccharide monooxygenases and evaluation effect of its addition into Aspergillus fumigatus var. niveus cocktail for sugarcane bagasse saccharification.

Lignocellulosic biomass is a promising alternative for producing biofuels, despite its recalcitrant nature. There are microorganisms in nature capable of efficiently degrade biomass, such as the filamentous fungi. Among them, Aspergillus fumigatus var. niveus (AFUMN) has a wide variety of carbohydrate-active enzymes (CAZymes), especially hydrolases, but a low number of oxidative enzymes in its genome. To confirm the enzymatic profile of this fungus, this study analyzed the secretome of AFUMN cultured in sugarcane bagasse as the sole carbon source. As expected, the secretome showed a predominance of hydrolytic enzymes compared to oxidative activity. However, it is known that hydrolytic enzymes act in synergy with oxidative proteins to efficiently degrade cellulose polymer, such as the Lytic Polysaccharide Monooxygenases (LPMOs). Thus, three LPMOs from the fungus Thermothelomyces thermophilus (TtLPMO9D, TtLPMO9H, and TtLPMO9O) were selected, heterologous expressed in Aspergillus nidulans, purified, and used to supplement the AFUMN secretome to evaluate their effect on the saccharification of sugarcane bagasse. The saccharification assay was carried out using different concentrations of AFUMN secretome supplemented with recombinant T. thermophilus LPMOs, as well as ascorbic acid as reducing agent for oxidative enzymes. Through a statistic design created by Design-Expert software, we were able to analyze a possible cooperative effect between these components. The results indicated that, in general, the addition of TtLPMO9D and ascorbic acid did not favor the conversion process in this study, while TtLPMO9O had a highly significant cooperative effect in bagasse saccharification compared to the control using only AFUMN secretome.

Ethanol organosolv pretreatment of sugarcane bagasse assisted by organic acids and supercritical carbon dioxide.

The scCO2-assisted organosolv pretreatment of sugarcane bagasse was carried out using aqueous ethanol and organic acid catalysts. Variables involved were temperature (150-190 °C), time (0-60 min), type of catalyst (acetic, citric, and oxalic acids), amount of CO2 (25-50 g), ethanol titer in water (0-80 vol%), and catalyst concentration (0.5 to 1.5 % w·v-1). The best delignification (86 wt%) and glucan retention (89 wt%) were achieved at 170 °C for 15 min using 60 vol% ethanol in water, 1 wt% oxalic acid, and 25 g CO2. Organic acid esterification was a limitation for pretreatment operations using ethanol titers above 60 vol%. Enzymatic hydrolysis of pretreated materials at 1 % (w·v-1) glucans released 74.3 ± 0.2 % glucose in 96 h using Cellic CTec3 (Novozymes) at 9.89 FPU·gglucans-1. The concentrated pretreatment liquor allowed lignin recovery by water precipitation in high yields, while the aqueous supernatant contained low levels of fermentation inhibitors.

Optimization of chemical solution concentration and exposure time in the alkaline pretreatment applied to sugarcane bagasse for methane production.

ABSTRACTSugarcane is the most traded crop in the world, with Brazil being the world's largest producer. Sugarcane processing generates up to 28% of sugarcane bagasse (SB) from the entire plant, with only 50% of it used for energy generation. SB is a lignocellulosic biomass that can be converted into biogas. However, the optimization of pretreatment process parameters is essential for its successful scaling up. This study evaluated the effect of mild alkaline pretreatment of SB using NaOH and KOH at concentrations of 1-10% and exposure time of 1-12 hours) on the biochemical methane potential (BMP) under mesophilic temperature. The central composite rotatable design (CCRD) was applied as statistical tool to generate optimal operating pretreatment conditions. The tests were performed in triplicates totalizing 84 batch bottles. The BMP of the untreated SB varied between 297-306 LN CH4 kg VS-1 while the BMP of the pretreated samples with NaOH and KOH were 19% and 20% higher. The optimized conditions were NaOH at 7.7% and KOH at 8.3% KOH for 12 hours. However, the range indicated by the statistical design with CCRD revealed that there was no statistical difference in terms of methane yield when concentrations between 4-10% NaOH and 6-10% KOH during 12 hours were applied, when compared to the specific optimized points. The optimization of the pretreatment parameters demonstrated to be a key-factor to improve the anaerobic digestion of lignocellulosic substrates, leading to a less chemically dependent and more sustainable approach, while allowing a more profitable process.

Dilute acid pretreatment for enhancing the enzymatic saccharification of agroresidues using a Botrytis ricini endoglucanase.

The enormous amount of agroindustrial residues generated in Brazil can be used as biomass to produce fermentable sugars. This study compared the pretreatments with different proportions of dilute acid. The method involved pretreatment with 0.5%, 1%, and 1.5% (v/v) sulfuric acid, followed by hydrolysis using the halotolerant and thermostable endoglucanase from Botrytis ricini URM 5627. The physicochemical characterization of plant biomass was performed using XRD, FTIR, and SEM. The pretreatment significantly increased the production of fermentable sugars following enzymatic saccharification from wheat bran, sugarcane bagasse, and rice husk: 153.67%, 91.98%, and 253.21% increment in sugar production; 36.39 mg⋅g-1 ± 1.23, 39.55 mg⋅g-1 ± 1.70, and 42.53 mg⋅g-1 ± 7.61 mg⋅L-1 of glucose; and 3.26 ± 0.35 mg⋅g-1 , 3.61mg⋅g-1 ± 0.74 and 3.59 mg⋅g-1 ± 0.80 of fructose were produced, respectively. In conclusion, biomass should preferably be pretreated before the enzymatic saccharification using B. ricini URM 5627 endoglucanase.