Preparation of deep eutectic solvent modified magnetic graphene oxide/metal organic framework nanocomposites for the extraction of three estrogens in cosmetics.

A novel magnetic dispersive solid phase extraction (MDSPE) procedure based on the deep eutectic solvent (DES) modified magnetic graphene oxide/metal organic frameworks nanocomposites (MGO@ZIF-8@DES) was established and used for the efficient enrichment of estradiol, estrone, and diethylstilbestrol in cosmetics (toner, lotion, and cream) for the first time. Then, the three estrogens were separated and determined by UHPLC-UV analysis method. In order to study the features and morphology of the synthesized adsorbents, various techniques such as FT-IR, SEM, and VSM measurements were executed. The MGO@ZIF-8@DES nanocomposites combine the advantages of high adsorption capacity, adequate stability in aqueous solution, and convenient separation from the sample solution. To achieve high extraction recoveries, the Box-Behnken design and single factor experiment were applied in the experimental design. Under the optimum conditions, the method detection limits for three estrogens were 20-30 ng g-1. This approach showed a good correlation coefficient (r more than 0.9998) and reasonable linearity in the range 70-10000 ng g-1. The relative standard deviations for intra-day and inter-day were beneath 7.5% and 8.9%, respectively. The developed MDSPE-UHPLC-UV method was successfully used to determine  three estrogens in cosmetics, and acceptable recoveries in the intervals of 83.5-95.9% were obtained. Finally, three estrogens were not detected in some cosmetic samples. In addition, the Complex GAPI tool was used to evaluate the greenness of the developed pretreatment method. The developed MDSPE-UHPLC-UV method is sensitive, accurate, rapid, and eco-friendly, which provides a promising strategy for determining hormones in different complex samples.

Estrogenic Activity of Mycoestrogen (3ß,5α,22E)-Ergost-22-en-3-ol via Estrogen Receptor α-Dependent Signaling Pathways in MCF-7 Cells.

Armillariella tabescens (Scop.) Sing., a mushroom of the family Tricholomataceae, has been used in traditional oriental medicine to treat cholecystitis, improve bile secretion, and regulate bile-duct pressure. The present study evaluated the estrogen-like effects of A. tabescens using a cell-proliferation assay in an estrogen-receptor-positive breast cancer cell line (MCF-7). We found that the methanol extract of A. tabescens fruiting bodies promoted cell proliferation in MCF-7 cells. Using bioassay-guided fractionation of the methanol extract and chemical investigation, we isolated and identified four steroids and four fatty acids from the active fraction. All eight compounds were evaluated by E-screen assay for their estrogen-like effects in MCF-7 cells. Among the tested isolates, only (3ß,5α,22E)-ergost-22-en-3-ol promoted cell proliferation in MCF-7 cells; this effect was mitigated by the ER antagonist, ICI 182,780. The mechanism underlying the estrogen-like effect of (3ß,5α,22E)-ergost-22-en-3-ol was evaluated using Western blot analysis to detect the expression of extracellular signal-regulated kinase (ERK), phosphatidylinositol 3-kinase (PI3K), Akt, and estrogen receptor α (ERα). We found that (3ß,5α,22E)-ergost-22-en-3-ol induced an increase in phosphorylation of ERK, PI3K, Akt, and ERα. Together, these experimental results suggest that (3ß,5α,22E)-ergost-22-en-3-ol is responsible for the estrogen-like effects of A. tabescens and may potentially aid control of estrogenic activity in menopause.

Highly sensitive determination of endocrine disrupting chemicals in foodstuffs through magnetic solid-phase extraction followed by high-performance liquid chromatography-tandem mass spectrometry.

BACKGROUND: Endocrine disrupting chemicals (EDCs), proved to be potential carcinogenic threats to human health, have received great concerns in food field. It was essential to develop effective methods to detect EDCs in food samples. The present study proposed an efficient method to determine trace EDCs including estrone (E1), 17ß-estradiol (E2), estriol (E3) and bisphenol A (BPA) based on magnetic solid-phase extraction (MSPE) coupled high-performance liquid chromatography-tandem mass spectrometry (HPLC-MS/MS) in meat samples. RESULTS: Fe3 O4 @COF(TpBD)/TiO2 nanocomposites were synthesized via functionalization of magnetic covalent organic frameworks (COFs) with titanium dioxide (TiO2 ) nanoparticles, and used as absorbents of MSPE to enrich EDCs. The efficient EDCs enrichment relies on π-π stacking interaction, hydrogen bonding, and the interaction between titanium ions (IV, Ti4+ ) and hydroxyl groups in EDCs, which improves the selectivity and sensitivity. Under the optimized conditions, target EDCs were rapidly extracted through MSPE with 5 min. Combining Fe3 O4 @COF(TpBD)/TiO2 based MSPE and HPLC-MS/MS to determine EDCs, good linearities were observed with correlation coefficient (R2 ) ≥ 0.9989. The limits of detection (LODs) and limits of quantification (LOQs) were 0.13-0.41 µg kg-1 and 0.66-1.49 µg kg-1 , respectively. Moreover, the proposed method was successfully applied to real samples analysis. CONCLUSIONS: The established MSPE-HPLC-MS/MS method was successfully applied to determine EDCs in meat samples with rapidness, improved selectivity and sensitivity. It shows great prospects for EDCs detection in other complicated matrices. © 2020 Society of Chemical Industry.

Enhanced adsorption of steroid estrogens by one-pot synthesized phenyl-modified mesoporous silica: Dependence on phenyl-organosilane precursors and pH condition.

In this study, the phenyl-modified mesoporous materials were successfully synthesized using phenyl-organosilanes (trimethoxyphenylsilane and triethoxyphenylsilanea) by one-pot co-condensation method for the removal of estrone (E1), 17ß-estradiol (E2), and 17α-ethinyl estradiol (EE2). Both the triethoxyphenylsilane-modified material (20%EtPh-MCM-41) and trimethoxyphenylsilane-modified material (20%MePh-MCM-41) could rapidly achieve equilibrium in 30 min at low adsorbent dosage of 0.025 g L-1. But the different hydrolysable groups of trimethoxyphenylsilane and triethoxyphenylsilane led to the discrepancies in physicochemical properties of the 20%EtPh-MCM-41 and 20%MePh-MCM-41, and thus affected adsorption performance. The 20%EtPh-MCM-41 exhibited the faster estrogen adsorption rates expressed in pseudo-second-order kinetic constant than the 20%MePh-MCM-41 due to the more hydrophobicity. Conversely, the 20%MePh-MCM-41 had much more estrogen adsorption capacities than the 20%EtPh-MCM-41 because of the more available adsorption sites. The addition of the phenyl-organosilane improved estrogen adsorption by π-π and hydrophobic interactions, and the Langmuir-model-based maximum adsorption amounts could reach 99.02, 83.47, and 53.60 mg g-1 for EE2, E2, and E1, respectively. But excessive concentration of phenyl-organosilane decreased adsorption capacities due to poor pore structure. Alkaline solution, which induced estrogen deprotonation and negative surface charge of absorbents, inhibited estrogen adsorption by electrostatic repulsion and the decreased hydrophobic interaction, but acidic and neutral solutions, ionic strength, and humic acid did not significantly affect estrogen removal. This work not only showed the high potential of trimethoxyphenylsilane-modified MCM-41 used in water purification for steroid estrogens, but also demonstrated the suitable selection of organosilane precursors was key in producing favorable materials with designed functionality.

Study of the adsorption of endocrine disruptor compounds on typical filter materials using a quartz crystal microbalance.

Drinking water containing environmental endocrine disruptor compounds (EDCs) endangers human health, and researching the purification process of drinking water for the effective removal of EDCs is vitally important. Filtering plays a crucial role in the bio-adsorption of EDCs, but the adsorption mechanism that occurs between the EDCs and filters remains unclear. In this study, a quartz crystal microbalance (QCM) was employed to elucidate the adsorption mechanism because QCM is a label-free method that possesses high selectivity, high stability, and high sensitivity. The results indicated that a pseudo-first-order kinetic model best fits the adsorption process of four different EDCs, which included bisphenol A (BPA), estrone (E1), estradiol (E2), and sulfamethoxazole (SMZ), on silica (quartz sand), a typical filter material surface. The order of the amount of individual EDCs absorbed on the silica surface was qE2 > qE1 > qSMZ > qBPA and related to their molecular structure, polarity, and chargeability. As the initial EDC concentration increased, the adsorbed amount of the four EDCs on the silica surface increased; however, the initial concentration had little effect on removal efficiency. The calculated Freundlich exponent (1/n) demonstrated SMZ and BPA showed a greater tendency for adsorption than E1 and E2. The mass response time on the surface of the silica gradually increased as the pH increased (from 5.5 to 8.5), indicating the adsorption rate was inhibited by the increase in pH. The addition of electrolytes shortened the mass response time of EDCs on the QCM chip. The pH and ionic strength produced no significant effects on adsorption because hydrophobicity was the primary contributor to adsorption. This study facilitated a better understanding of the interaction between EDCs and filters in water treatment.

Determination of estrone and 17α-ethinylestradiol in digested sludge by ultrasonic liquid extraction and high-performance liquid chromatography with fluorescence detection.

Estrone, 17ß-estradiol and 17α-ethinylestradiol are increasingly recognised as important micropollutants to be monitored in wastewater treatment plants. These estrogens are retained onto sludge due to their high adsorption and since they are largely used in land applications, the monitoring of these chemicals in sludge samples is of great importance. This study describes a method for the determination of estrone and 17α-ethinylestradiol in fresh sludge samples. After spiking fresh digested sludge with estrone and 17α-ethinylestradiol and maintaining in contact during 5, 30 and 60 min, the freeze-dried samples were subjected to ultrasonic liquid extraction, with methanol and acetone, and analysed by high-performance liquid chromatography with fluorescence detection. The average recoveries obtained for estrone and 17α-ethinylestradiol using the different contact times were 103 ± 3 and 97 ± 4%, respectively. Fresh sludge samples from one waste water treatment plant located in Portugal were analysed and estrone was detected in primary fresh sludge, anaerobic digested sludge and dehydrated sludge at a concentration in the range of 1-4.8 µg/g. The method here developed does not require any sample clean-up, being fast and simple, reliable and inexpensive, making possible its application for monitoring the contamination of sludge with these estrogens.

N-propyl functionalized spherical mesoporous silica as a rapid and efficient adsorbent for steroid estrogen removal: Adsorption behaviour and effects of water chemistry.

To achieve an enhanced and selective adsorption of steroid estrogens, the n-propyl functionalization was applied to the mesoporous silica material (MCM-41) according to the physico-chemical property analysis of steroid estrogens. Adsorption behaviour and water chemistry effects were evaluated with the most concerned steroid estrogens: estrone (E1), 17ß-estradiol (E2) and 17α-ethinyl estradiol (EE2) based on the materials characterization. The results showed the uptakes of E1, E2, and EE2 onto the modified MCM-41 were enhanced and accelerated by the n-propyl functionalization, which was positively correlated with the hydrophobicity of the synthesized materials. Kinetic data fitted the pseudo-second-order model well. Based on the Langmuir model, the maximum adsorption capacities of the n-propyl modified MCM-41 were up to 119.87, 88.38, and 86.91 mg g-1 for EE2, E1, and E2, respectively. Importantly, both acid and neutral solutions were beneficial to estrogen removal, but ionic strength and humic acid did not affect the estrogen adsorption. The above results suggested that the n-propyl functionalized MCM-41 would be a promising adsorbent for the rapid and efficient removal of estrogens with the selectivity from natural organic matter like humic acid. Mechanism analysis showed the key role of hydrophobic interaction, and it also confirmed the contribution of the carbonylic lone pair electrons of E1, which helped the formation of stronger hydrogen bonds with silicon hydroxyls and enhanced the dipole-dipole interaction between E1 and the synthesized materials.

Adsorption of estrone with few-layered boron nitride nanosheets: Kinetics, thermodynamics and mechanism.

Boron nitride Nanosheets (BNNSs) was fabricated with a method of heating the mixture of boric acid and urea in N2 atmosphere and used to remove estrone (E1) from water. The obtained BNNSs exhibited a higher surface area of 896 m2/g, a large pore volume of 0.76 cm3/g, and only few layers (0.398 nm) with the boric acid and urea ratio of 1:80. The layer number of BNNSs decreased from 15 to 4 with the mole ratio of boric acid and urea decreasing from 1:20 to 1:80, which was identified by SEM, TEM, AFM and BET measurements. More importantly, BNNSs presented an outstanding adsorption performance for estrone with the adsorption capacity of 249.15 mg E1/g BNNSs. The adsorption process could be best fitted by pseudo second-order kinetic model and the equilibrium data at different temperatures were well fitted by Langmuir isotherm model. The thermodynamics analysis revealed that E1 adsorption on BNNSs was spontaneous (ΔG = -29.33 kJ mol-1), enthalpy-retarded (ΔH = 29.75 kJ mol-1), entropy-driven (ΔS = 198.26 J mol-1 K-1), and mostly chemical adsorption. The adsorption rates of E1 in water were sharply enhanced with thinner BNNSs as absorbents and removal efficiency by BN-60 regenerated after 6 times was above 95%, it was shown that the surface areas, mesopores and remarkable structure played important roles in the adsorption process. The firmness of E1 onto BNNSs and the stability of adsorption efficiency made BNNSs as a potential absorbent for efficient removal of E1 from wastewater.

Facile preparation of polydopamine-coated imprinted polymers on the surface of SiO2 for estrone capture in milk samples.

Estrone molecularly imprinted polymers were synthesized through the self-polymerization of dopamine on the surface of silica gels, which had the characteristics of mild polymerization conditions, simple reaction procedure and good specific recognition ability for estrone. The estrone molecularly imprinted polymers were characterized by scanning electron microscopy, Fourier transform infrared spectroscopy, thermogravimetric analysis, elemental analysis and nitrogen adsorption-desorption tests. The characterization confirmed that the imprinted polymers were successfully grafted on the surface of silica gels. Through investigating the adsorption performance, the prepared estrone molecularly imprinted polymers exhibited high adsorption capacity, fast mass transfer, as well as excellent selectivity toward estrone. The estrone molecularly imprinted polymers as the solid-phase extraction adsorbent coupled with high-performance liquid chromatography was developed to determine estrone from the milk samples. The developed estrone molecularly imprinted polymer solid-phase extraction with high-performance liquid chromatography method exhibited satisfactory specificity, precision, accuracy and good linearity relationship in the range of 0.2-20 µg/mL. The developed method is simple, fast, effective and high specificity method and it provides a new method to detect the residues of estrone in animal foods.

A MALDI-MS-based quantitative analytical method for endogenous estrone in human breast cancer cells.

The level of endogenous estrone, one of the three major naturally occurring estrogens, has a significant correlation with the incidence of post-menopausal breast cancer. However, it is challenging to quantitatively monitor it owing to its low abundance. Here, we develop a robust and highly sensitive mass-assisted laser desorption/ionization mass spectrometry (MALDI-MS)-based quantitative platform to identify the absolute quantities of endogenous estrones in a variety of clinical specimens. The one-step modification of endogenous estrone provided good linearity (R(2) > 0.99) and significantly increased the sensitivity of the platform (limit of quantitation: 11 fmol). In addition, we could identify the absolute amount of endogenous estrones in cells of the breast cancer cell line MCF-7 (34 fmol/10(6) cells) by using a deuterated estrone as an internal standard. Finally, by applying the MALDI-MS-based quantitative method to endogenous estrones, we successfully monitored changes in the metabolic expression level of estrones (17.7 fmol/10(6) letrozole-treated cells) in MCF-7 cells resulting from treatment with an aromatase inhibitor. Taken together, these results suggest that this MALDI-MS-based quantitative approach may be a general method for the targeted metabolomics of ketone-containing metabolites, which can reflect clinical conditions and pathogenic mechanisms.