Aluminum Alloy Anode with Various Iron Content Influencing the Performance of Aluminum-Ion Batteries.

Considerable research has been devoted to the development of cathode materials for Al-ion batteries, but challenges remain regarding the behavior of aluminum anodes. Inert oxide (Al2O3) film on Al surfaces presents a barrier to electrochemical activity. The structure of the oxide film needs to be weakened to facilitate ion transfer during electrochemical activity. This study addresses oxide film challenges by studying Al alloy anodes with different iron content. The results reveal that using an anode of 99% Al 1% Fe in a cell increases the cycling lifetime by 48%, compared to a 99.99% Al anode. The improvement observed with the 99% Al 1% Fe anode is attributed to its fractional surface area corrosion being about 12% larger than that of a 99.99% Al anode. This is coupled to precipitation of a higher number of Al3Fe particles, which are evenly scattered in the Al matrix of 99% Al 1% Fe. These Al3Fe particles constitute weak spots in the oxide film for the electrolyte to attack, and access to fresh Al. The addition of iron to an Al anode thus offers a cheap and easy route for targeting the oxide passivating film challenge in Al-ion batteries.

A review of the advances in composites/nanocomposites for triboelectric nanogenerators.

Material development is essential when studying triboelectric nanogenerators (TENGs). This importance is because the performance of TENGs is highly dependent on the properties of the utilized triboelectric materials. To obtain more specific properties, composites have been developed that combine the features of their components. According to Google Scholar, 55% of published papers related to triboelectric nanogenerators have utilized or mentioned composites. This number is 34.5% if one searches with the keyword nanocomposites instead of composites. The importance of composites is because they can exhibit new dielectric properties, better mechanical strength, enhanced charge affinities, etc. Therefore, the development of new composites has great importance in TENG studies. In this paper, we review the production of nanocomposites, the types of nanocomposites, and their application in TENG studies. This review gives an overview of how nanocomposites boost the performance of TENGs and provides guidance for future studies.

Highly Stable Cycling of Silicon-Nanographite Aerogel-Based Anode for Lithium-Ion Batteries.

Silicon anodes are considered as promising electrode materials for next-generation high capacity lithium-ion batteries (LIBs). However, the capacity fading due to the large volume changes (∼300%) of silicon particles during the charge-discharge cycles is still a bottleneck. The volume changes of silicon lead to a fracture of the silicon particles, resulting in recurrent formation of a solid electrolyte interface (SEI) layer, leading to poor capacity retention and short cycle life. Nanometer-scaled silicon particles are the favorable anode material to reduce some of the problems related to the volume changes, but problems related to SEI layer formation still need to be addressed. Herein, we address these issues by developing a composite anode material comprising silicon nanoparticles and nanographite. The method developed is simple, cost-efficient, and based on an aerogel process. The electrodes produced by this aerogel fabrication route formed a stable SEI layer and showed high specific capacity and improved cyclability even at high current rates. The capacity retentions were 92 and 72% of the initial specific capacity at the 171st and the 500th cycle, respectively.

Cellulose-Based Fully Green Triboelectric Nanogenerators with Output Power Density of 300 W m-2.

Triboelectric nanogenerators (TENGs) have attracted increasing attention because of their excellent energy conversion efficiency, the diverse choice of materials, and their broad applications in energy harvesting devices and self-powered sensors. New materials have been explored, including green materials, but their performances have not yet reached the level of that for fluoropolymers. Here, a high-performance, fully green TENG (FG-TENG) using cellulose-based tribolayers is reported. It is shown that the FG-TENG has an output power density of above 300 W m-2 , which is a new record for green-material-based TENGs. The high performance of the FG-TENG is due to the high positive charge density of the regenerated cellulose. The FG-TENG is stable after more than 30 000 cycles of operations in humidity of 30%-84%. This work demonstrates that high-performance TENGs can be made using natural green materials for a broad range of applications.

Silicon-Nanographite Aerogel-Based Anodes for High Performance Lithium Ion Batteries.

To increase the energy storage density of lithium-ion batteries, silicon anodes have been explored due to their high capacity. One of the main challenges for silicon anodes are large volume variations during the lithiation processes. Recently, several high-performance schemes have been demonstrated with increased life cycles utilizing nanomaterials such as nanoparticles, nanowires, and thin films. However, a method that allows the large-scale production of silicon anodes remains to be demonstrated. Herein, we address this question by suggesting new scalable nanomaterial-based anodes. Si nanoparticles were grown on nanographite flakes by aerogel fabrication route from Si powder and nanographite mixture using polyvinyl alcohol (PVA). This silicon-nanographite aerogel electrode has stable specific capacity even at high current rates and exhibit good cyclic stability. The specific capacity is 455 mAh g-1 for 200th cycles with a coulombic efficiency of 97% at a current density 100 mA g-1.

Frequency and voltage response of a wind-driven fluttering triboelectric nanogenerator.

Triboelectric nanogenerators (TENG:s) are used as efficient energy transducers in energy harvesting converting mechanical energy into electrical energy. Wind is an abundant source of mechanical energy but how should a good triboelectric wind harvester be designed? We have built and studied a TENG driven by air flow in a table-top sized wind tunnel. Our TENG constitutes of a plastic film of size 10 cm × 2 cm which is fluttering between two copper electrodes generating enough power to light up a battery of LED:s. We measured the voltage and frequency of fluttering at different wind speeds from zero up to 8 m/s for three electrode distances 6 mm, 10 mm and 14 mm. We found that the frequency increases linearly with the wind speed with a cutoff at some low speed. Power was generated already at 1.6 m/s. We seem to be able to explain the observed frequency dependence on wind speed by assuming excitation of the film into different harmonics in response to von Kármán vortices. We also find that the voltage increase linearly with frequency. We anticipate that TENG:s of this design could be useful both as generators and speed sensors because they work at low air speeds.

Schottky model for triboelectric temperature dependence.

The triboelectric effect, charging by contact, is the working principle in a device called a triboelectric nanogenerator. They are used as efficient energy transducers in energy harvesting. In such generators the charging of surfaces at contact is followed by a separation of the surfaces increasing the electrical energy which can subsequently be used. Different materials have different triboelectric potentials leading to charging at contact. The temperature dependence of the charging has just recently been studied: the triboelectric effect is decreasing with temperature for a generator of Al-PTFE-Cu. Here, we suggest a mechanism to explain this effect assuming ion transfer using a two-level Schottky model where the two levels corresponds to the two surfaces. The difference in binding energy for ions on the two surfaces then enters the formula for charging. We fit the triboelectric power density as a function of temperature obtained from a two-level Schottky model to measured data for nanogenerators made of Al-PTFE-Cu found in three references. We obtain an average separation energy corresponding to a temperature of 365 K which is of the right magnitude for physically adsorbed atoms. We anticipate that this model could be used for many types of triboelectric nanogenerators.

Photoconductivity of acid exfoliated and flash-light-processed MoS2 films.

MoS2 has been studied intensively during recent years as a semiconducting material in several fields, including optoelectronics, for applications such as solar cells and phototransistors. The photoresponse mechanisms of MoS2 have been discussed but are not fully understood, especially the phenomenon in which the photocurrent slowly increases. Here, we report on a study of the photoresponse flash-light-processed MoS2 films of different thicknesses and areas. The photoresponse of such films under different light intensities and bias voltages was measured, showing significant current changes with a quick response followed by a slow one upon exposure to pulsed light. Our in-depth study suggested that the slow response was due to the photothermal effect that heats the MoS2; this hypothesis was supported by the resistivity change at different temperatures. The results obtained from MoS2 films with various thicknesses indicated that the minority-carrier diffusion length was 1.36 µm. This study explained the mechanism of the slow response of the MoS2 film and determined the effective thickness of MoS2 for a photoresponse to occur. The method used here for fabricating MoS2 films could be used for fabricating optoelectronic devices due to its simplicity.

Quantification of the second-order nonlinear susceptibility of collagen I using a laser scanning microscope.

Characteristic changes in the organization of fibrillar collagen can potentially serve as an early diagnostic marker in various pathological processes. Tissue types containing collagen I can be probed by pulsed high-intensity laser radiation, thereby generating second harmonic light that provides information about the composition and structure at a microscopic level. A technique was developed to determine the essential second harmonic generation (SHG) parameters in a laser scanning microscope setup. A rat-tail tendon frozen section was rotated in the xy-plane with the pulsed laser light propagating along the z-axis. By analyzing the generated second harmonic light in the forward direction with parallel and crossed polarizer relative to the polarization of the excitation laser beam, the second-order nonlinear optical susceptibilities of the collagen fiber were determined. Systematic variations in SHG response between ordered and less ordered structures were recorded and evaluated. A 500 microm-thick z-cut lithiumniobate (LiNbO(3)) was used as reference. The method was applied on frozen sections of malignant melanoma and normal skin tissue. Significant differences were found in the values of d(22), indicating that this parameter has a potential role in differentiating between normal and pathological processes.

A study of kinetic molecular exchange processes in the medium frequency range by surface SHG on an oscillating bubble.

The dilatational properties of fluid surfaces and interfaces have been comprehensively investigated in recent years. For example, an improved oscillating bubble device provided experimental results that allow for critical testing of established surface models, such as the Lucassen/van den Tempel (LvdT) model. The comparison of the LvdT model with the oscillating bubble experiments demonstrates a mismatch between the model parameters. For example, near the CMC or the limit of solubility the calculated parameters of surfactant solutions become unrealistically large. The deviation can be explained by the introduction of more detailed surface models, in particular by the modification of the effective thickness of the surface layer, its internal structure and the molecular exchange processes between these structures. For the verification of such processes an experimental setup was realized which allows for an independent determination of the instantaneous adsorption state at the surface of an oscillating bubble inside a surfactant solution. The setup utilizes the Second Harmonic Generation (SHG)--effect at the air-solution interface generated by the light of a pulsed LASER. The set-up is described in detail, and the results of a first experimental series are presented and discussed in this paper. As system, aqueous solutions of the fluortenside F381 were used.