Study of Lightweight Ceramic Matrix-Less Syntactic Foam Composed of Cenosphere Using Spark Plasma Sintering.

The current investigation presents porous ceramic materials prepared with cenospheres (CS) by using spark plasma sintering. The impact of sintering temperature, mould diameter (20, 30 and 50 mm) and cenosphere size on the properties of the sintered material was investigated. Shrinkage of the samples during sintering started at 900 °C. Total sample shrinkage during sintering increases with increasing temperature and decreases with increasing mould size; increasing sample sintering temperature increases the apparent density of all sample series CS 63-150 µm in a 20 mm mould from 0.97 to 2.3 g·cm-3 at 1050-1300 °C; in a 30 mm mould, 0.81-1.87 g·cm-3 at 1050-1200 °C; in 50 mm mould, 0.54-0.75 g·cm-3 at 1050-1150 °C; while CS 150-250 µm in a 20 mm mould is 0.93-1.96 g·cm-3 at 1050-1200 °C. Total porosity decreases from 61.5% to 3.9% by increasing sintering temperature from 1050 to 1250 °C, while open porosity reduces at lower temperatures, with closed porosity being highest in samples sintered at 1150 °C. When the sintering temperature increases from 1050 to 1300 °C, the compressive strength of the CS 63-150 samples produced in a 20 mm mould increases from 11 MPa to 312 MPa. These results correlate with the Rice model, which describes an exponential dependence of compressive strength on material porosity and fully dense material compressive strength.

Preparation and Characteristics of High-Performance, Low-Density Metallo-Ceramics Composite.

By applying the physical vapour deposition method, hollow ceramic microspheres were coated with titanium, and subsequently, they were sintered using the spark plasma sintering technique to create a porous ceramic material that is lightweight and devoid of a matrix. The sintering process was carried out at temperatures ranging from 1050 to 1200 °C, with a holding time of 2 min. The samples were subjected to conventional thermal analyses (differential scanning calorimetry, thermogravimetry, dilatometry), oxidation resistance tests, and thermal diffusivity measurements. Phase analysis of the samples was performed using the XRD and the microstructure of the prepared specimens was examined using electron microscopy. The titanium coating on the microspheres increased the compressive strength and density of the resulting ceramic material as the sintering temperature increased. The morphology of the samples was carefully examined, and phase transitions were also identified during the analysis of the samples.

High-Temperature, Lightweight Ceramics with Nano-Sized Ferrites for EMI Shielding: Synthesis, Characterisation, and Potential Applications.

The present study focuses on the synthesis and characterisation of a lightweight ceramic material with electromagnetic interference (EMI) shielding properties, achieved using mullite containing micrometre-sized hollow spheres (cenospheres) and CoFe2O4 nanoparticles. This research explores compositions with varying CoFe2O4 contents ranging from 0 up to 20 wt.%. Conventional sintering in an air atmosphere is carried out at a temperature between 1100 and 1300 °C. The addition of ferrite nanoparticles was found to enhance the process of sintering cenospheres, resulting in improved material density and mechanical properties. Furthermore, this study reveals a direct correlation between the concentration of ferrite nanoparticles and the electromagnetic properties of the material. By increasing the concentration of ferrite nanoparticles, the electromagnetic shielding effect of the material (saturation magnetisation (Ms) and remanent magnetisation (Mr)) was observed to strengthen. These findings provide valuable insights into designing and developing lightweight ceramic materials with enhanced electromagnetic shielding capabilities. The synthesized ceramic material holds promise for various applications that require effective electromagnetic shielding, such as in the electronics, telecommunications, and aerospace industries.

The Effect of Zinc Oxide on DLP Hybrid Composite Manufacturability and Mechanical-Chemical Resistance.

The widespread use of epoxy resin (ER) in industry, owing to its excellent properties, aligns with the global shift toward greener resources and energy-efficient solutions, where utilizing metal oxides in 3D printed polymer parts can offer extended functionalities across various industries. ZnO concentrations in polyurethane acrylate composites impacted adhesion and thickness of DLP samples, with 1 wt.% achieving a thickness of 3.99 ± 0.16 mm, closest to the target thickness of 4 mm, while 0.5 wt.% ZnO samples exhibited the lowest deviation in average thickness (±0.03 mm). Tensile stress in digital light processed (DLP) composites with ZnO remained consistent, ranging from 23.29 MPa (1 wt.%) to 25.93 MPa (0.5 wt.%), with an increase in ZnO concentration causing a reduction in tensile stress to 24.04 MPa and a decrease in the elastic modulus to 2001 MPa at 2 wt.% ZnO. The produced DLP samples, with their good corrosion resistance in alkaline environments, are well-suited for applications as protective coatings on tank walls. Customized DLP techniques can enable their effective use as structural or functional elements, such as in Portland cement concrete walls, floors and ceilings for enhanced durability and performance.

Physical, Thermal, and Chemical Properties of Fly Ash Cenospheres Obtained from Different Sources.

Cenospheres are hollow particles in fly ash, a by-product of coal burning, and are widely used as a reinforcement when developing low-density composites called syntactic foams. This study has investigated the physical, chemical, and thermal properties of cenospheres obtained from three different sources, designated as CS1, CS2, and CS3, for the development of syntactic foams. Cenospheres with particle sizes ranging from 40 to 500 µm were studied. Different particle distribution by size was observed, and the most uniform distribution of CS particles was in the case of CS2: above 74% with dimensions from 100 to 150 µm. The CS bulk had a similar density for all samples and amounted to around 0.4 g·cm-3, with a particle shell material density of 2.1 g·cm-3. Post-heat-treatment samples showed the development of a SiO2 phase in the cenospheres, which was not present in the as-received product. CS3 had the highest quantity of Si compared to the other two, showing the difference in source quality. Energy-dispersive X-ray spectrometry and a chemical analysis of the CS revealed that the main components of the studied CS were SiO2 and Al2O3. In the case of CS1 and CS2, the sum of these components was on average from 93 to 95%. In the case of CS3, the sum of SiO2 and Al2O3 did not exceed 86%, and Fe2O3 and K2O were present in appreciable quantities in CS3. Cenospheres CS1 and CS2 did not sinter during heat treatment up to 1200 °C, while sample CS3 was already subjected to sintering at 1100 °C because of the presence of a quartz phase, Fe2O3 and K2O. For the application of a metallic layer and subsequent consolidation via spark plasma sintering, CS2 can be deemed the most physically, thermally, and chemically suitable.