Fatliquor for fungus resistant leather-a sustainable ecofriendly approach.

Surface-active softening agents, such as Fatliquors, have a significant impact on the leather industry as they enhance the physicochemical properties of leather. This study focuses on analyzing the synthesis, properties, characterization, and sulfonation of Swietenia mahagoni seed oil to determine its potential as a fatliquoring agent for leather. An investigation was conducted to verify the alteration of Swietenia mahagoni oil through the analysis of its properties before and after the sulfonation process. A scientific analysis was carried on the oil using GC-FID, revealing the presence of various unsaturated fatty acids such as linoleic, linolenic, oleic, palmitic, and arachidic acids. This demonstrates the sulfonating capability of this sky fruit seed oil. A fatliquor was created by sulfonating the oil, and the sulfonation was verified through Fourier Transform Infrared Spectroscopy (FTIR) and 1H Nuclear Magnetic Resonance (NMR) spectra. The prominent peak observed at 1209 cm-1 in the FTIR spectra indicated the stretching of S=O in both sulfate and sulfonate groups. The newly formed protons (H-C-S or H-C-O) showed signals between δ 4.09 and 4.29 ppm in the 1H NMR spectra, confirming the sulfonation of the fatliquor that was prepared. Moreover, the change in the melting point of sulfonated Mahogany oil from 40.8 °C to 48.1 °C suggests increased saturation levels. The fatliquor's emulsion stability was found to be at a satisfactory level. After conducting tests on the treated leather, the physical strength and morphological structure was analyzed using Field Emission Scanning Electron Microscopy (FE-SEM), the fatliquor improved the lubrication and strengthened the fibrous network structure of the leather, composed of thin and tight collagen fibers. The BOD5/COD ratio of the effluent from the experimental trial was determined to be 0.52, suggesting that the fatliquor developed is a biodegradable product. Finally, the antifungal capabilities of the fatliquor-treated leather were tested against four different fungus species: Aspergillus niger, Aspergillus flavus, Penicillium notatum, and Candida albicans, and the treated leather sample shown favorable antifungal activity.

Comparative evaluation of tannin from banana bunch and stem syrup for leather processing.

Utilization of vegetable tannins in leather processing is one of the convenient solutions to protect the environment pollution. Herein, the banana bunch and syrup of banana stem are utilized to prepare an ecofriendly tanning agent. The yield of banana bunch extraction efficiency is found 69.80 %. FT-IR analysis confirmed the presence of condensed type tanning component owing to the bearing of different polyphenolic groups. The content of tannins in extracted banana bunch and stem syrup is 3.13 % and 2.6 %, respectively. The phenolic content in the banana bunch extract is determined to be 1332.37 mg GAE/100g of dried weight and in syrup was 873.92 mg GAE/100g of dried weight. This makes it possible to be used as vegetable tanners. The extracted bunch and syrup are applied to re-tan leather and compared with conventionally used vegetable tanning agent (quebracho) in parallel. Tensile strength, tear strength and elongation percentage for the extracted banana bunch and syrup are obtained at 23.84 N/mm2, 68.26 N/mm, 47.07 %, and 22.97 N/mm2, 68.38 N/mm, 40.70 %, respectively. The softness is found 1.41 for the extracted bunch and 2.01 for the syrup. The grain crack load, distension at grain crack, strength at ball burst, distension at ball burst are 246.86 N, 13.24 mm, 530.77 N, 24.54 mm for banana stem syrup and 338.77 N, 13.42 mm, 460.65 N, 29.08 mm for bunch extract, respectively. The shrinkage temperatures recorded for banana bunch extract, syrup and Quebracho (control trial) tannins tanned leather samples are 76.5 °C, 75 °C and 84 °C subsequently. The flexing endurance of the bunch extract and syrup revealed acceptable values that are less than 4. Moreover, the bunch extract tanned leather shows greater thermal stability and for syrup it is similar with the quebracho tanned leather. All the results are satisfactory compared to the control trial. Finally, tanned leather is evaluated to assess the possibility of the newly developed tannin which proves its efficiency as a potential source of tanning material for the leather industry.

Spatiotemporal distribution, ecological risk assessment, and human health implications of currently used pesticide (CUP) residues in the surface water of Feni River, Bangladesh.

Spatiotemporal monitoring of pesticide residues in river water is urgently needed due to its negative environmental and human health consequences. The present study is to investigate the occurrence of multiclass pesticide residue in the surface water of the Feni River, Bangladesh, using an optimized salting-out assisted liquid-liquid microextraction (SALLME) coupled with liquid chromatography-tandem mass spectrometry (LC-MS/MS). The optimized SALLME method was developed and validated following the SANTE/11312/2021 guidelines. A total of 42 water samples were collected and analyzed to understand the spatiotemporal distribution of azoxystrobin (AZ), buprofezin (BUP), carbofuran (CAR), pymetrozine (PYM), dimethoate (DMT), chlorantraniliprole (CLP), and difenoconazole (DFN). At four spike levels (n = 5) of 20, 40, 200, and 400 µg/L, the recovery percentages were satisfactory, ranging between 71.1 % and 107.0 % (RSD ≤13.8 %). The residues ranged from below the detection level (BDL) to 14.5 µg/L. The most frequently detected pesticide was DMT (100 %), followed by CLP (52.3809-57.1429), CAR (4.7619-14.2867), and PYM (4.7619-9.5238). However, AZ and BUP were below the detection limit in the analyzed samples of both seasons. Most pesticides and the highest concentrations were detected in March 2023, while the lowest concentrations were present in August 2023.Furthermore, ecological risk assessment based on the general-case scenario (RQm) and worst-case scenario (RQex) indicated a high (RQ > 1) risk to aquatic organisms, from the presence of PYM and CLP residue in river water. Human health risk via dietary exposure was estimated using the hazard quotient (HQ). Based on the detected residues, the HQ (<1) value indicated no significant health risk. This report provides the first record of pesticide residue occurrences scenario and their impact on the river environment of Bangladesh.

Utilization of factory tea (Camellia sinensis) wastes in eco-friendly dyeing of jute packaging fabrics.

Eco-friendly dyeing of jute packaging fabrics was evaluated using aqueous extraction of factory tea (Camellia sinensis) wastes. Jute and factory tea wastes are available in Bangladesh and jute bags are used for packaging of various exportable agricultural commodities. The extract of factory tea waste (FTW) is dark coffee colored and it was characterized by attenuated total reflection-fourier transform infrared (ATR-FTIR) and microbial analysis. Nontoxic, non-allergic and eco-friendly natural dyeing process of jute packaging fabrics using extract of FTW were developed and optimized. Metal mordants 10 % on the weight of fabric was used to get the fastness properties of dyed jute fabric. The methods of application of mordants were pre-mordanting, simultaneous or meta-mordanting and post-mordanting. The color fastness and tensile properties were measured for all jute packaging fabrics and it is found that the dyed jute packaging fabrics showed a slight decrease in tensile breaking force (N) than undyed jute packaging fabric. The highest color fastness obtained with the meta mordanting method with ferrous sulfate mordant in a shade of dark coffee. The results of the color fastness for light and washing showed an excellent value of grade 4-5.

Source-specific geochemical and health risk assessment of anthropogenically induced metals in a tropical urban waterway.

Thorough deliberation is necessary to safeguard the tropical urban streams near the shoreline from human interference, as it is becoming a notable environmental danger. Consequently, an in-depth study was carried out on a significant urban waterway located on the southern seashore of Bangladesh, which is positioned in the Bengal delta, renowned as the largest delta in the globe. The current investigation assesses the potential health hazards associated with trace metals (Hg, Cu, As, Pb, Ni, Zn, Cd, Cr, Fe, and Mn) and uses chemometric analysis to determine where they originate. Likewise geochemical methods are used to analyze the levels of trace metal enrichment and pollution in the sediments of the river. Almost all of the elements' mean concentrations were observed to be within the standard limits. The findings not only demonstrate the extent of trace metal contamination but also the health threats that it poses to the public (male, female, and children) by polluting the sediment. For all age groups of people, the hazard index was <1, suggesting there was no non-carcinogenic threat. Regardless of age and sex, exposure occurred in descending order: ingestion > dermal > inhalation. Total carcinogenic risk (TCR) values for males, females, and children were 1.45E-05, 1.56E-05, and 1.34E-04, respectively, recommending that children are at greater vulnerability than adults. The geochemical approach and chemometric analysis corroborate the human-induced impact of trace metal loading in the sediment of the waterway, which is predominantly caused by the oil industry, domestic garbage, and untreated waste discharge.

Holistic perilous index-based environmental appraisal of Metal(oid)s in the sole coral-bearing island of northeastern bay of Bengal.

This study aimed to evaluate the concentration, distribution, along with the environmental and human health impact of eight heavy metals-Pb, Cr, Cu, Cd, Zn, Mn, Ni, and As-on St. Martin's Island in the northeastern Bay of Bengal, and in doing so to help implement new legislations to protect the island. Focusing on the island's significance as a tourist destination, with seafood being a prominent dietary component, three sample types (sediment, seawater, and crustaceans) were selected for a comprehensive assessment, considering seasonal variations. Concentration of metals was observed to be lower than the established standards in sediment samples, but in seawater samples, Pb, Cr, Cd and Zn were higher than US-EPA values for natural marine water. The metals displayed a decreasing trend of Zn > Ni > Pb > Cu > Mn > As > Cd > Cr in crustacean samples for both seasons. Crustacean samples displayed higher metal concentrations in winter than in monsoon. Pb exceeded the maximum allowable limit for crustaceans with a concentration of about 3 and 4 mg kg-1 in monsoon and winter respectively; being more than 6-8 times the standard for Bangladesh which is only about 0.5 mg kg-1. Health indices displayed that although adults may suffer less from carcinogenic/non-carcinogenic health effects, the risks are far greater for children. For both age groups, As and Ni displayed possibilities of developing cancer. Principal Component Analysis (PCA)shed light on the sources of metals and showed that most of them were from anthropogenic sources. Overall, this study found that the quality of the environment of the island was better in comparison to previous studies made before the pandemic, and so, if the trend continues, it may lead to a better environment for the organisms around the island and help to keep the negative physiological impacts from the consumption of these organisms to a minimal.

Fabrication and Characterization of a Bioscaffold Using Hydroxyapatite and Unsaturated Polyester Resin.

Outstanding biodegradability and biocompatibility are attributes associated with particular polyester substances that make this group useful in specific biomedical fields. To assess the potential as a biomaterial, a novel composite consisting of hydroxyapatite (HAp) and unsaturated polyester resin (UPR) was developed in this work. Using a hand-lay-up technique, various percentages (50, 40, 30, 20, and 10%) of HAp were reinforced into the UPR matrix to fabricate composite materials out of glass sheets. Prior to processing of the composite samples, hydroxyapatite was chemically synthesized in a wet chemical manner. Using a universal testing machine (UTM), Fourier transform infrared (FTIR) spectroscopy, scanning electron microscopy (SEM), and thermo-gravimetric analysis (TGA), the fabricated samples were characterized. The crystallographic parameters of synthesized hydroxyapatite (HAp) were also estimated through a range of formulas. The optimal amount for hydroxyapatite was 40% according to the findings of the tensile strength (TS), tensile modulus (TM), percentage of elongation at break (EB), bending strength (BS), and bending modulus (BM). Improvements in TS, TM, BS, and BM for the ideal combination were 39.39, 9.21, 912.05, and 259.96%, in each case, over the controlled one. Thermogravimetric analysis (TGA) has been implemented to determine the degradation temperature of the fabricated composites up to 600 °C.

Synthesis of pure and doped nano-calcium phosphates using different conventional methods for biomedical applications: a review.

The applications of calcium phosphates (hydroxyapatite, tetracalcium phosphate, tricalcium phosphate (alpha and beta), fluorapatite, di-calcium phosphate anhydrous, and amorphous calcium-phosphate) are increasing day by day. Calcium hydroxyapatite, commonly known as hydroxyapatite (HAp), represents a mineral form of calcium apatite. Owing to its close molecular resemblance to the mineral constituents of bones, teeth, and hard tissues, HAp is often employed in the biomedical domain. In addition, it is extensively employed in various sectors such as the remediation of water, air, and soil pollution. The key advantage of HAp lies in its potential to accommodate a wide variety of anionic and cationic substitutions. Nevertheless, HAp and tricalcium phosphate (TCP) syntheses typically involve the use of chemical precursors containing calcium and phosphorus sources and employ diverse techniques, such as solid-state, wet, and thermal methods or a combination of these processes. Researchers are increasingly favoring natural sources such as bio-waste (eggshells, oyster shells, animal bones, fish scales, etc.) as viable options for synthesizing HAp. Interestingly, the synthesis route significantly influences the morphology, size, and crystalline phase of calcium phosphates. In this review paper, we highlight both dry and wet methods, which include six commonly used synthesis methods (i.e. solid-state, mechano-chemical, wet-chemical precipitation, hydrolysis, sol-gel, and hydrothermal methods) coupled with the variation in source materials and their influence in modifying the structural morphology from a bulky state to nanoscale to explore the applications of multifunctional calcium phosphates in different formats.

Method development of multi pesticide residue analysis in country beans collected from Dhaka, Bangladesh, and their dietary risk assessment.

The aim of the study was to develop a modified QuEChERS method coupled with liquid chromatography-tandem mass spectrometry (LC-MS/MS) for the simultaneous determination of five multi-class pesticides in country beans collected from Dhaka, Bangladesh. Pesticides were extracted using ACN, and to minimize the co-extraction matrix, optimized d-SPE cleanup was done using sorbents (GCB, PSA, and C18). In the calibration range, the method showed excellent linearity with a correlation coefficient of R2 ≥ 0.9990 both in solvent- and matrix-matched calibration. For the selected pesticides, average recoveries (at four spiking levels (n = 5) of 10, 20, 100, and 200 µg/kg) of 70-100 % were achieved with relative standard deviations (RSDs) ≤ 9.5 %. The limit of detection (LOD) and limit of quantification (LOQ) ranged from 0.3333 to 1.3333 µg/kg and 1.0 to 4.0 µg/kg, respectively. The dietary risk assessment, in terms of hazard quotient (HQ), was calculated to assess consumers' health risks.

Ophiorrhiza mungos-Mediated Silver Nanoparticles as Effective and Reusable Adsorbents for the Removal of Methylene Blue from Water.

Green synthesis of silver nanoparticles (AgNPs) using a plant extract has attracted significant attention in recent years. It is found as an alternative for other physicochemical approaches because of its simplicity, low cost, and eco-friendly rapid steps. In the present study, Ophiorrhiza mungos (Om)-mediated AgNPs have been shown to be effective bioadsorbents for methylene blue (MB) dye removal (88.1 ± 1.74%) just after 1 h at room temperature in the dark from an aqueous medium for the first time. Langmuir and Freundlich isotherms fit the experimental results having the correlation coefficient constants R2 = 0.9956 and R2 = 0.9838, respectively. From the Langmuir fittings, the maximum adsorption capacity and adsorption intensity were found to be 80.451 mg/g and 0.041, respectively, indicating the excellent performance and spontaneity of the process. Taking both models under consideration, interestingly, our findings indicated a fairly cooperative multilayer adsorption that might have been governed by chemisorption and physisorption, whereas the adsorption kinetics followed the pseudo-second-order kinetics mechanism. The positive and low values of enthalpy (ΔH0 = 4.91 kJ/mol) confirmed that adsorption is endothermic and physical in nature; however, the negative free energy and positive entropy value (ΔS0 = 53.69 J/mol K) suggested that the adsorption is spontaneous. The biosynthesized adsorbent was successfully reused up to the fifth cycle. A proposed reaction mechanism for the adsorption process of MB dye onto Om-AgNPs is suggested. The present study may offer a novel finding such as an effective and sustainable approach for the removal of MB dye from water using biosynthesized Om-AgNPs as reusable adsorbents at a comparatively faster rate at a low dose for industrial applications.

Phase tunable nickel doped Mn3O4 nanoparticle synthesis by chemical precipitation: kinetic study on dye degradation.

Nickel (Ni) doped Mn3O4 nanoparticles (NPs) were synthesized by a quick and facile chemical precipitation technique to investigate their performance in the degradation of methylene blue (MB) in the absence of light. XRD, FESEM, TEM, AAS, XPS, and FT-IR were used for the investigation of the structural, surface morphological, and elemental composition of Ni doped Mn3O4 NPs. XRD confirms the formation of a tetragonal phase structure of pure Mn3O4 and 1% and 3% Ni doped Mn3O4 NPs. However, mixed phases were found in the case of 5 to 10% Ni doped Mn3O4 NPs. Well-defined spherical-shaped morphology was presented through FESEM. Particle sizes decreased linearly (58.50 to 23.68 nm) upon increasing the doping concentration from 0% (pure Mn3O4) to 7% respectively, and then increased (48.62 nm) in the case of 10% doping concentration. TEM further confirmed spherical shaped 32 nm nanoparticles for 7% Ni doped Mn3O4. The elemental composition and oxidation state of the prepared NPs were confirmed by using XPS spectra. Mixed valence Mn2+ and Mn4+ states were found in pure Mn3O4 and 1% and 3% Ni doped Mn3O4 NPs in the ratio of 2MnO-MnO2. In addition, three different oxidation states Mn2+, Mn3+, and Mn4+ were found in 5 to 10% Ni doped Mn3O4 NPs. Moreover, as a dopant Ni exists as Ni2+ and Ni3+ states in all Ni doped Mn3O4 NPs. The synthesized NPs were then applied as potent oxidants for the degradation of MB at pH 3. With the increase of doping concentration to 7%, the degree of degradation was increased to 79% in the first 10 min and finally, it became about 98%. The degradation of MB follows the pseudo-first-order linear kinetics with a degradation rate of 0.0342 min-1.

Genetic variants rs2910164, rs4636297 and rs895819 may contribute to the onset of acute myocardial infarction in Pakistani population.

The most serious type of coronary artery disease (CAD), acute myocardial infarction (AMI), is a major global cause of death. The development of AMI is accompanied by several risk factors. AMI may be caused by variations in the microRNA (miRNA) genes, which have a negative impact on miRNA-mediated regulation of gene expression. The target mRNAs are dysregulated because of these genetic changes in the miRNA genes, which interfere with the vital biological processes that result in AMI. Using allele-specific PCR, the aim of the study is to examine the association of the variants (rs2910164, rs4636297, and rs895819) in MIR146A, MIR126, and MIR27A with AMI susceptibility. A difference in genotype distribution among the patients and control for variation rs2910164 was identified by co-dominant [χ2 = 68.34,2; P value<0.0001], dominant (G/G vs G/C + C/C) [OR = 4.167 (2.860-6.049); P value<0.0001], recessive (C/C vs G/C + G/G) [OR = 0.2584 (0.1798-0.3731); P value<0.0001], and additive models [OR = 3.847 (2.985-4.959); P value<0.0001]. Whereas the association of rs4636297 was investigated by co-dominant [χ2 = 6.882,2; P value = 0.0320], dominant (G/G vs G/A + A/A) [OR = 0.6914 (0.4849-0.9948); P value = 0.0489], recessive (A/A vs A/G + G/G) [OR = 2.434 (0.9849-5.616830); P value = 0.0595], and additive models [OR = 0.7716 (0.6000-0.9918); P value = 0.0433]. Similarly, association of rs895819 was determined by co-dominant [χ2 = 5.277, 2; P value = 0.0715], dominant (G/G vs G/A + A/A) [OR = 1.654(0.9819-2.801); P value = 0.06440], recessive (A/A vs A/G + G/G) [OR = 0.7227 (0.5132-1.022); P value = 0.0748], and additive models [OR = 1.3337 (1.041-1.719); P value = 0.0233]. The results of this study found a significant association of rs2910164 and rs4636297 with AMI and are considered as the risk factor for AMI in the Pakistani population. We observed no significant association of the variant MIR27A (rs895819) with AMI incidence.

Impaired intestinal immunity and microbial diversity in common carp exposed to cadmium.

Waterborne cadmium (Cd) accumulates in the fish intestine and causes irreversible toxicity by disrupting intestinal immunity and microbial diversity. To explore the toxicity of environmentally available high Cd concentration on intestinal immunity and microbial diversity of fish, we selected the widely used bioindicator model species, Common carp (Cyprinus carpio). Literature review and Cd pollution data supported sequential doses of 0.2, 0.4, 0.8, 1.6, 3.2, and 6.4 mg/L Cd for 30 days. Based on intestinal tissue Cd accumulation, previous studies, and environmentally available Cd data, 0.4 and 1.6 mg/L Cd were selected for further studies. Intestinal Cd bioaccumulation increased significantly to ~100 times in fish exposed to 1.6 mg/L Cd. We observed villous atrophy, increased goblet cells with mucus production, muscularis erosion, and thickened lamina propria due to intense inflammatory cell infiltration in the intestine at this Cd concentration. Cd-induced immunosuppression occurred with increased lysozyme, alkaline phosphate (AKP), and acid phosphate (ACP). High levels of catalase (CAT), total antioxidant capacity (T-AOC), malondialdehyde (MDA), and hydrogen peroxide (H2O2) suggested induced oxidative stress and poor metabolism by α-amylase and lipase suppression for Cd toxicity. Proteobacteria (41.2 %), Firmicutes (21.8 %), and Bacteroidetes (17.5 %) were the dominant bacterial phyla in the common carp intestine. Additionally, potential pathogenic Cyanobacteria increased in Cd-treated fish. The decrease of beneficiary bacteria like Aeromonas, and Cetobacterium indicated Cd toxicity. Overall, these findings indicate harmful consequences of high Cd concentration in the intestinal homeostasis and health status of fish.

The miRNA variants MIR196A2 (rs11614913) and MIR423 (rs6505162) contribute to an increase in the risk of myocardial infarction.

INTRODUCTION: MicroRNAs (miRNAs) are small, single-stranded RNA molecules that negatively regulate gene expression and play a key role in the pathogenesis of human diseases. Recent studies have suggested that miRNAs contribute to cardiovascular diseases (CVDs). However, the association between single-nucleotide polymorphisms (SNPs) in miRNAs and myocardial infarction (MI) remains in infancy. AIM: The current study was designed to find out the association of SNPs in MIR196A2 and MIR423 (rs11614913 and rs6505162, respectively). METHODS: Using Tetra-Primer Amplification Refractory Mutation System-Polymerase Chain Reaction (T-ARMS PCR) in 400 cases (MI patients) and 336 healthy controls. Using different inheritance models (co-dominant, homozygous dominant, homozygous recessive, and additive models), the association of these SNPs was genotyped with MI risk. RESULTS: For variant rs11614913, significant distribution of the genotypes among the cases and controls was determined by co-dominant [χ2 = 29.19, 2; p value < 0.0001], dominant (C/C vs. C/T + T/T) [OR = 0.45 (0.34 to 0.61); p < 0.0001], recessive (T/T vs. C/T + C/C) [OR = 1.009 (0.63 to 1.63); p-value p value > 0.999], and additive models [OR = 0.65 (0.52 to 0.80); p value = 0.0001]. Similarly, a significant association of rs6505162 was determined by co-dominant [χ2 = 24.29, 2; p value < 0.0001], dominant (C/C vs. A/C+ A/A) [OR = 0.44 (0.32 to 0.61); p value < 0.0001], recessive (A/A vs. A/C + C/C) [OR = 1.29 (0.85 to 1.98); p value = 0.28], and additive models [OR = 0.65 (0.52 to 0.81); p value = 0.0001]. CONCLUSION: Therefore, the current study showed that both variants rs11614913 and rs6505162 are significantly associated with MI in the Pakistani population.

Genome sequencing of Pakistani families with male infertility identifies deleterious genotypes in SPAG6, CCDC9, TKTL1, TUBA3C, and M1AP.

BACKGROUND: There are likely to be hundreds of monogenic forms of human male infertility. Whole genome sequencing (WGS) is the most efficient way to make progress in mapping the causative genetic variants, and ultimately improve clinical management of the disease in each patient. Recruitment of consanguineous families is an effective approach to ascertain the genetic forms of many diseases. OBJECTIVES: To apply WGS to large consanguineous families with likely hereditary male infertility and identify potential genetic cases. MATERIALS AND METHODS: We recruited seven large families with clinically diagnosed male infertility from rural Pakistan, including five with a history of consanguinity. We generated WGS data on 26 individuals (3-5 per family) and analyzed the resulting data with a computational pipeline to identify potentially causal single nucleotide variants, indels, and copy number variants. RESULTS: We identified plausible genetic causes in five of the seven families, including a homozygous 10 kb deletion of exon 2 in a well-established male infertility gene (M1AP), and biallelic missense substitutions (SPAG6, CCDC9, TUBA3C) and an in-frame hemizygous deletion (TKTL1) in genes with emerging relevance. DISCUSSION AND CONCLUSION: The rate of genetic findings using the current approach (71%) was much higher than what we recently achieved using whole-exome sequencing (WES) of unrelated singleton cases (20%). Furthermore, we identified a pathogenic single-exon deletion in M1AP that would be undetectable by WES. Screening more families with WGS, especially in underrepresented populations, will further reveal the types of variants underlying male infertility and accelerate the use of genetics in the patient management.

Trace metals in transboundary (India-Myanmar-Bangladesh) anadromous fish Tenualosa ilisha and its consequences on human health.

Hilsa shad (Tenualosa ilisha, Hamilton, 1822), the highly coveted table fish within the Indian subcontinent, is Bangladesh's most significant single-species fishery. To assess the risk that toxic metals pose to human health, certain health risk indices-estimated daily intake (EDI), target hazard quotient (THQ), total target hazard quotient (TTHQ), and target cancer risk (TR)-were calculated. The hierarchy of toxic metals (µg/g-ww) in Hilsa shad of the bay showed as Zn (13.64 ± 2.18) > Fe (9.25 ± 1.47) > Mn (2.98 ± 0.75) > Cu (0.57 ± 0.18) > Cr (0.23 ± 0.06) > Pb (0.22 ± 0.04) > As (0.08 ± 0.02) > Ni (0.06 ± 0.02) > Co (0.04 ± 0.01) > Cd (0.01 ± 0.003) in the wet season and Zn (11.45 ± 1.97) > Fe (10.51 ± 1.38) > Mn (3.80 ± 0.75) > Cu (0.73 ± 0.17) > Pb (0.30 ± 0.03) > Cr (0.20 ± 0.05) > As (0.09 ± 0.01) > Ni (0.08 ± 0.02) > Co (0.07 ± 0.02) > Cd (0.02 ± 0.004) in the dry season. The EDI of all the examined trace metals indicated no risk to human health from consuming Hilsa fish. The estimation of THQ and TTHQ suggested that the ingestion of both individual and combined trace metals through Hilsa shad consumption was safe from the perspective of human health. Also, there was no evidence of carcinogenic risk for consumers based on the evaluation of the TR value of metals (As, Pb, Cd, and Ni) due to Hilsa shad consumption.

Effect of Reaction Parameters on CO2 Absorption from Biogas Using CaO Sorbent Prepared from Waste Chicken Eggshell.

This study provides an efficient and straightforward approach to eliminate carbon dioxide (CO2) by absorption using a calcium oxide (CaO) sorbent derived from chicken eggshells. The sorbent concentration, stirring speed, and contact time were varied. The optimal condition for CO2 removal was a 10% calcium hydroxide (Ca(OH)2) suspension at 600 rpm with 20 min interaction. This optimum condition conferred the ever-highest absorption (98.71%) of CO2 through Ca(OH)2 suspensions from eggshell-derived CaO. X-ray diffraction was used to identify crystallographic phases and optimum conditions revealed calcium carbonate (CaCO3) formation with the highest intensity, Fourier transform infrared spectroscopy revealed peaks for the carbonate (CO32-) group, field emission scanning electron microscopy was used to investigate the morphological and structural properties of the sorbent before and after CO2 absorption, and thermogravimetric analysis was performed to understand the reaction mechanism. According to the kinetic analysis, the sorbent can be fully decomposed with a minimum activation energy (Ea) of 89.09 kJ/mol.

M gene targeted qRT-PCR approach for SARS-CoV-2 virus detection.

Quantitative reverse transcriptase polymerase chain reaction (qRT-PCR) is the gold standard method for SARS-CoV-2 detection, and several qRT-PCR kits have been established targeting different genes of the virus. Due to the high mutation rate of these genes, false negative results arise thus complicating the interpretation of the diagnosis and increasing the need of alternative targets. In this study, an alternative approach for the detection of SARS-CoV-2 viral RNA targeting the membrane (M) gene of the virus using qRT-PCR was described. Performance evaluation of this newly developed in-house assay against commercial qRT-PCR kits was done using clinical oropharyngeal specimens of COVID-19 positive patients. The limit of detection was determined using successive dilutions of known copies of SARS-CoV-2 pseudovirus. The M gene based assay was able to detect a minimum of 100 copies of virus/mL indicating its capacity to detect low viral load. The assay showed comparable accuracy, sensitivity and specificity with commercially available kits while detecting all the variants efficiently. The study concluded that the in-house M gene based assay might be an effective alternative for the currently available commercial qRT-PCR kits.

ß-tricalcium phosphate synthesized in organic medium for controlled release drug delivery application in bio-scaffolds.

ß-tricalcium phosphate (ß-TCP) was synthesized in an organic medium (acetone) to obtain a single-phase product while calcium carbonate (CaCO3) and ortho-phosphoric acid (H3PO4) were the sources of Ca, and P, respectively. The synthesized ß-TCP was characterized by employing a number of sophisticated techniques vis. XRD, FTIR, FESEM, VSM and UV-Vis-NIR spectrometry. On the other hand, cytotoxicity, hemolysis, and antimicrobial activity for Gram-negative as well as Gram-positive (E. coli and S. aureus) bacteria were explored using this synthesized sample in powder format. However, to assess the drug loading and releasing profile, these powdered samples were first compressed into disks followed by sintering at 900 °C. Prior to loading the drug, porosity, density, and water absorbance characteristics of the scaffolds were examined in deionized water. Both loading and releasing profiles of the antibiotic (ciprofloxacin) were looked over at various selected time intervals which were continued up to 28 days. The observed results revealed that 2.87% of ciprofloxacin was loaded while 37% of this loaded drug was released within the selected time frame as set in this study. The scaffold was also immersed in SBF solution maintaining identical interim periods for the bioactivity evaluation. Furthermore, all three types of samples (e.g. drug-loaded, drug-released, and SBF-soaked) were characterized by FESEM and EDX while antimicrobial activity (against E. coli, S. typhi, and S. aureus) and efficacy to prevent hemolysis were also investigated. The drug-loaded scaffold presented a larger inhibition zone than the standard for all three types of microbes. Although powdered ß-TCP was inactive in killing the Gram-negative bacteria, surprisingly the drug-released scaffold showed an inhibition zone.

Influence of Sn doping on the optoelectronic properties of ZnO nanoparticles.

Zinc Oxide (ZnO) nanoparticles (NPs) obtained a lot of attention from researchers and industries because of their superior properties as an optoelectronic material. Doping, especially tin (Sn), can further fine-tune their optoelectronic properties. In this manuscript, we have reported the optoelectronic properties of Sn-doped ZnO NPs, which were synthesized by a simple chemical solution method. A wide range of dopant (Sn) concentrations were used in the ratios of 0, 1, 3, 5, 7, and 10 weight percent. The effects of dopant (Sn) concentration on the structural, morphological, elemental composition, and optical properties of ZnO NPs were investigated by using an X-ray diffractometer (XRD), Field Emission Scanning Electron Microscope (FESEM), X-ray photoelectron spectrometer (XPS) and UV-Vis-NIR respectively. XRD analysis revealed the shifting of diffraction patterns towards a higher angle along with decreasing intensity. The calculated crystallite size using the XRD varied from 40.12 nm to 28.15 nm with an increasing doping percentage. Sn doping notably influences the size of ZnO NPs, along with crystal quality, strain, and dislocation density. The X-ray photoelectron spectroscopy (XPS) study showed the presence of zinc (Zn), oxygen (O), and tin (Sn) with their preferred oxidation states in the synthesized NPs. UV-Visible spectroscopy (UV-Vis) showed that the bandgap changed from 3.55 to 3.85 eV with the increasing concentration of Sn. FE-SEM revealed that the structures and surfaces were irregular and not homogeneous. The above findings for ZnO nanostructures show their potential application in optoelectronic devices.