Impact of Nanoparticles Additions on the Strength of Dental Composite Resin.

Objective: This study aimed to evaluate the effect of nanoparticles, zirconium dioxide (ZrO2), titanium dioxide (TiO2), and silicon dioxide (SiO2), on flexural strength (FS), hardness, and wear resistance of light cured dental composite resin. Materials and Methods: 210 rectangular and disc-shaped composite resin specimens were fabricated with dimensions (25 × 2 × 2 ± 0.03 mm) and (6×4 ± 0.03 mm) for FS, hardness, and wear resistance, respectively (70/test). Specimens of each test were divided according to nanofillers into four groups, unmodified as control, ZrO2 (Z), TiO2 (T), and SiO2 (S) groups; each one was further subdivided into two subgroups according to nanoparticles concentration, 3wt.% and 7wt.% (Z3, Z7, T3, T7, S3, and S7), 10 specimens of each subgroup. A3-point bending test and Vickers hardness test were used for FS and hardness measurements, respectively. Wear resistance was evaluated by the differences in surface roughness of tested specimens before and after wear test. Two-way and 1-way ANOVA and Bonferroni's post hoc tests were done for data analysis (α = 0.05). Results: Two-way ANOVA for FS and wear resistance showed that there was a significant interaction between type of nanoparticles and concentration of nanoparticles (p < 0.001) while two-way ANOVA for hardness showed that both type of nanoparticles and concentration of nanoparticles had a significant effect (p < 0.001), while the effect of their interaction was not statistically significant (p=0.142). 1-way-ANOVA test showed significant increase in FS and wear resistance for all tested groups (p < 0.001 and p < 0.001, respectively) except T7 and S7. Also, there was a significant enhancement in hardness for all tested groups (p < 0.001). Conclusion: Modification of light cured composite resin with certain amounts of nanoparticles (3% and 7% of ZrO2 and 3% of TiO2 and SiO2) can be beneficial in improving flexural strength and wear resistance while hardness of composite resin was increased with all NPs additions.

Comparative Effect of Incorporation of ZrO2, TiO2, and SiO2 Nanoparticles on the Strength and Surface Properties of PMMA Denture Base Material: An In Vitro Study.

Objective: This study aimed to investigate the effects of nanoparticles (zirconium dioxide (ZrO2), titanium dioxide (TiO2), and silicon dioxide (SiO2)) on the flexural strength, impact strength, hardness, and wear resistance of the acrylic resin denture base material. Materials and Methods: Acrylic resin specimens were fabricated in dimensions according to American Dental Association (ADA) specifications per test. Specimens were divided according to nanofiller into four groups; unmodified as control, ZrO2 (Z), TiO2, (T), and SiO2 (S) groups. Each one was subdivided into two subgroups according to nanoparticle concentrations; 3% and 7% (Z3, Z7, T3, T7, S3, and S7). A 3-point bending test, Charpy impact test, and Vickers hardness test were used for flexural strength, impact strength, and hardness measurements, respectively. Wear resistance was measured by the differences in surface roughness of tested specimens before and after the wear test. A scanning electron microscope was used to assess nanoparticle specifications and distributions and for fracture surfaces analysis. ANOVA, Bonferroni's post hoc test, and the Kruskal-Wallis test were applied for data analysis (α = 0.05). Results: Regarding the flexural and impact strength, there was a statistically remarkable increase for all tested groups compared with the control group, except for the T7 and S7 groups (P value <0.001, effect size = 0.893) and (P value <0.001, effect size = 0.759), respectively. There was a statistically significant improvement in the hardness of all tested groups compared with the control group (P value <0.001, effect size = 0.67) except T3 and S3. Regarding wear, a statistically significant enhancement was noticed in the wear resistance of all tested groups (P value <0.001, effect size = 0.685), except for the T7 and S7 groups. Conclusion: The flexural strength, impact strength, and wear resistance improved with both concentrations of ZrO2 and low TiO2 and SiO2 concentrations. The hardness increased with both concentrations of ZrO2 and high TiO2 and SiO2 concentrations.

Influence of Different Beverages on the Color Stability of Nanocomposite Denture Base Materials.

BACKGROUND: The effect of beverages on nanocomposite denture base materials is neglected. Therefore, this study aimed to investigate the influence of different beverages (coffee, tea, cola, and mineral water) on the color stability of nanoparticles-modified denture base materials (DBMs). MATERIALS AND METHODS: A total of 280 specimens (n = 10/group) were prepared from heat-polymerized acrylic resin modified with different concentrations (3% and 7%) of zirconium dioxide (nano-ZrO2), titanium dioxide (nano-TiO2), and silicon dioxide (nano-SiO2) nanoparticles, while 0% was taken as a control. Color change (∆E) of the specimens was evaluated after simulating 6-month immersion time in four commonly used beverages, coffee, tea, cola, and mineral water, as experimental groups. Color stability was measured using a spectrophotometer, and then values were converted to National Bureau of Standards units (NBS units). The one-way ANOVA test was applied to compare color change (ΔE) results followed by Bonferroni's post hoc test (α = 0.05). RESULTS: The results showed that the heat-polymerized acrylic resin modified with different types of nanoparticles showed lower color changes after being immersed in beverage solutions compared to the unmodified group (P < 0.001), so the color stability of heat-polymerized acrylic resin was significantly enhanced by the addition of several nanoparticles; nano-ZrO2 showed the lowest ΔE followed by nano-TiO2 and then nano-SiO2. Regardless of the filler type, 3% concentration showed lower mean ΔE than 7% concentration. Regarding the beverage solutions, the greatest color change was found in the coffee group followed by tea and cola, while water showed the least changes. CONCLUSION: Modification of heat-polymerized acrylic resin with certain amounts of nano-ZrO2, nano-TiO2, and nano-SiO2 may be useful in improving color stability.

Effect of SiO2 and Al2 O3 nanoparticles on wear resistance of PMMA acrylic denture teeth / Efeito das nanopartículas de SiO2 e Al2 O3 na resistência ao desgaste de dentes em acrílico PMMA para prótese

Objetivo: Este estudo teve como objetivo avaliar a resistência ao desgaste de dentes em acrílico para próteses contendo nanopartículas de dióxido de silício (nano-SiO2 ) e dióxido de alumínio (nanoAl2 O3 ). Material e Métodos: O material em polimetilmetacrilato (PMMA) foi utilizado para fabricar 84 amostras (n=10) contendo nano-SiO2 e nano-Al2 O3 nas concentrações 0,1% em peso, 0,3% em peso e 0,5% em peso de pó acrílico. Uma máquina de teste de desgaste de dois corpos e um microscópio digital foram usados para medir as mudanças na perda de peso e rugosidade da superfície, respectivamente. Testes de ANOVA a um fator e testes de comparações múltiplas de Tukey foram utilizados para análise dos dados (α = 0,05). Resultados: O material modificado com nano-SiO2 demonstrou um aumento significativo na perda de peso em comparação com o material acrílico artificial convencional (p ˂ 0,05) enquanto o material modificado com nano-Al2 O3 demonstrou aumento não significativo na perda de peso, exceto no subgrupo 0,5% (p < 0,05). Não há diferenças significativas em relação à alteração da rugosidade após a simulação de desgaste entre todos os grupos testados (p > 0,05). Conclusão: As nanopartículas de nano-Al2 O3 exibem menos efeito negativo que o nanoSiO2 , podendo ser usado com cautela, se necessário. (AU)

Objective: This study aimed to evaluate the wear resistance of acrylic denture teeth containing silicon dioxide (nano-SiO2 ) and aluminum dioxide (nano-Al2 O3 ) nanoparticles. Material and Methods: Poly methyl methacrylate (PMMA) denture tooth material was used to denture tooth material was used to fabricate 84 specimens (n=10) containing nano-SiO2 and nano-Al2 O3 in concentrations 0.1wt%, 0.3wt%, and 0.5wt% of acrylic powder. A two-body wear testing machine and digital microscope were used to measure the changes in weight loss and surface roughness respectively. One-way ANOVA and pair-wise Tukey's post-hoc tests were used for data analysis (α = 0.05). Results: Nano-SiO2 modified teeth material demonstrated a significant increase in weight loss in comparison conventional artificial acrylic teeth material (p ˂ 0.05) while nanoAl2 O3 modified teeth material demonstrated non-significant increase in weight loss except for 0.5% subgroup (p ˂ 0.05). There is no significant differences regarding roughness change after wear simulation among all tested groups (p > 0.05). Conclusion: Nano-Al2 O3 nanoparticles exhibit less negative effect than nano-SiO2 so; it could be used with caution if necessary. (AU)