The enhanced ionic thermal potential by a polarized electrospun membrane.

Inspired by thermally sensitive ion channels in human skin, a polarized membrane composed of a ferroelectric polymer fiber matrix is used to double the heat-induced potential in ionic thermoelectric devices. The comparison of the thermal potentials between different directions of polarization and temperature gradient indicates the importance of cation-dipole interactions for the enhancement.

Cellulose-Based Radiative Cooling and Solar Heating Powers Ionic Thermoelectrics.

Cellulose opens for sustainable materials suitable for radiative cooling thanks to inherent high thermal emissivity combined with low solar absorptance. When desired, solar absorptance can be introduced by additives such as carbon black. However, such materials still shows high thermal emissivity and therefore performs radiative cooling that counteracts the heating process if exposed to the sky. Here, this is addressed by a cellulose-carbon black composite with low mid-infrared (MIR) emissivity and corresponding suppressed radiative cooling thanks to a transparent IR-reflecting indium tin oxide coating. The resulting solar heater provides opposite optical properties in both the solar and thermal ranges compared to the cooler material in the form of solar-reflecting electrospun cellulose. Owing to these differences, exposing the two materials to the sky generated spontaneous temperature differences, as used to power an ionic thermoelectric device in both daytime and nighttime. The study characterizes these effects in detail using solar and sky simulators and through outdoor measurements. Using the concept to power ionic thermoelectric devices shows thermovoltages of >60 mV and 10 °C temperature differences already at moderate solar irradiance of ≈400 W m-2 .

Methylammonium Lead Iodide Incorporated Poly(vinylidene fluoride) Nanofibers for Flexible Piezoelectric-Pyroelectric Nanogenerator.

This work introduces a piezoelectric-pyroelectric nanogenerator (P-PNG) based on methylammonium lead iodide (CH3NH3PbI3) incorporated electrospun poly(vinylidene fluoride) (PVDF) nanofibers that are able to harvest mechanical and thermal energies. During the application of a periodic compressive contact force at a frequency of 4 Hz, an output voltage of ∼220 mV is generated. The P-PNG has a piezoelectric coefficient (d33) of ∼19.7 pC/N coupled with a high durability (60 000 cycles) and quick response time (∼1 ms). The maximum generated output power density (∼0.8 mW/m2) is sufficient to charge up a variety of capacitors, with the potential to replace an external power supply to drive portable devices. In addition, upon exposure to cyclic heating and cooling at a temperature of 38 K, a pyroelectric output current of 18.2 pA and a voltage of 41.78 mV were achieved. The fast response time of 1.14 s, reset time of 1.25 s, and pyroelectric coefficient of ∼44 pC/m2 K demonstrate a self-powered temperature sensing capability of the P-PNG. These characteristics make the P-PNG suitable for flexible piezoelectric-pyroelectric energy harvesting for self-powered electronic devices.

Remarkable Output Power Density Enhancement of Triboelectric Nanogenerators via Polarized Ferroelectric Polymers and Bulk MoS2 Composites.

Performance enhancement of triboelectric nanogenerators (TENGs) has been largely limited by the relatively low output current density. Thus, extensive research efforts have been made to increase the output current density. In this respect, this work presents a method to effectively increase output current density of TENGs by adopting polarized ferroelectric polymers and MoS2 composite. Specifically, by compositing bulk MoS2 flakes with both Nylon-11 and PVDF-TrFE, respectively, charge density of each triboelectric charging surface was significantly increased. In addition, proper polarization of both ferroelectric composite layers has also led to an additional increase in the charge density. A combination of them synergistically increases the surface charge density, generating huge output current and the power output density. By optimizing the fabrication process, the output voltage and current density up to ∼145 V and ∼350 µA/cm2 are achieved, respectively. Consequently, the TENG exhibits a recordable output power density of ∼50 mW/cm2, which is one of the highest output power densities reported to date. The method introduced in this work can greatly increase the output current density of TENGs, facilitating the development of high-performance triboelectric energy harvesting devices.

Organo-Lead Halide Perovskite Induced Electroactive ß-Phase in Porous PVDF Films: An Excellent Material for Photoactive Piezoelectric Energy Harvester and Photodetector.

Methylammonium lead iodide (CH3NH3PbI3) (MAPI)-embedded ß-phase comprising porous poly(vinylidene fluoride) (PVDF) composite (MPC) films turns to an excellent material for energy harvester and photodetector (PD). MAPI enables to nucleate up to ∼91% of electroactive phase in PVDF to make it suitable for piezoelectric-based mechanical energy harvesters (PEHs), sensors, and actuators. The piezoelectric energy generation from PEH made with MPC film has been demonstrated under a simple human finger touch motion. In addition, the feasibility of photosensitive properties of MPC films are manifested under the illumination of nonmonochromatic light, which also promises the application as organic photodetectors. Furthermore, fast rising time and instant increase in the current under light illumination have been observed in an MPC-based photodetector (PD), which indicates of its potential utility in efficient photoactive device. Owing to the photoresponsive and electroactive nature of MPC films, a new class of stand-alone self-powered flexible photoactive piezoelectric energy harvester (PPEH) has been fabricated. The simultaneous mechanical energy-harvesting and visible light detection capability of the PPEH is promising in piezo-phototronics technology.

Electroactive ß-crystalline phase inclusion and photoluminescence response of a heat-controlled spin-coated PVDF/TiO2 free-standing nanocomposite film for a nanogenerator and an active nanosensor.

The electroactive ß-phase is most desirable due to its highest piezo-, pyro- and ferroelectric properties in poly(vinylidene fluoride) (PVDF). Induction of the ß-phase is successfully accomplished in titanium dioxide (TiO2) nanoparticles (NPs) doped spin-coated PVDF nanocomposite (PNC) films. The optimized yields of ß-phase and homogeneous ultra-smooth free-standing PNC film is utilized in a mechanical-energy harvesting application by fabricating a nanogenerator (NG) where the typical electrical poling step is not undertaken. Under a repeated human finger touch and release process, it delivers an open-circuit voltage of 5 V. Moreover, the physical sensing capabilities of the NG are examined through harvesting mechanical energy from mouse clicking of a laptop and wrist pulse detection, which indicates that it can also be used as a nanosensor. The blue photoluminescence centred at 444 nm, which was also observed in PNC films, makes us anticipate a new type of photonic application where the design feasibility of hybrid sensors, i.e. electromechanical and photonic combination, is also possible.

Improved dielectric constant and breakdown strength of γ-phase dominant super toughened polyvinylidene fluoride/TiO2 nanocomposite film: an excellent material for energy storage applications and piezoelectric throughput.

Titanium dioxide (TiO2) nanoparticles (NPs) embedded γ-phase containing polyvinylidene fluoride (PVDF) nanocomposite (PNC) film turns to an excellent material for energy storage application due to an increased dielectric constant (32 at 1 kHz), enhanced electric breakdown strength (400 MV m-1). It also exhibits a high energy density of 4 J cm-3 which is 25 times higher than that of virgin PVDF. 98% of the electroactive γ-phase has been acheived by the incorporation of TiO2 NPs and the resulting PNC behaves like a super-toughened material due to a dramatic improvement (more than 80%) in the tensile strength. Owing to their electroactive nature and extraordinary mechanical properties, PNC films have a strong ability to fabricate the piezoelectric nanogenerators (PNGs) that have recently been an area of focus regarding mechanical energy harvesting. The feasibility of piezoelectric voltage generation from PNGs is demostrated under the rotating fan that also promises further utility such as rotational speed (RPM) determination.

Native Cellulose Microfiber-Based Hybrid Piezoelectric Generator for Mechanical Energy Harvesting Utility.

A flexible hybrid piezoelectric generator (HPG) based on native cellulose microfiber (NCMF) and polydimethylsiloxane (PDMS) with multi wall carbon nanotubes (MWCNTs) as conducting filler is presented where the further chemical treatment of the cellulose and traditional electrical poling steps for piezoelectric voltage generation is avoided. It delivers a high electrical throughput that is an open circuit voltage of ∼30 V and power density ∼9.0 µW/cm(3) under repeated hand punching. We demonstrate to power up various portable electronic units by HPG. Because cellulose is a biocompatible material, suggesting that HPG may have greater potential in biomedical applications such as implantable power source in human body.

An Effective Electrical Throughput from PANI Supplement ZnS Nanorods and PDMS-Based Flexible Piezoelectric Nanogenerator for Power up Portable Electronic Devices: An Alternative of MWCNT Filler.

We demonstrate the requirement of electrical poling can be avoided in flexible piezoelectric nanogenerators (FPNGs) made of low-temperature hydrothermally grown wurtzite zinc sulfide nanorods (ZnS-NRs) blended with polydimethylsiloxane (PDMS). It has been found that conductive fillers, such as polyaniline (PANI) and multiwall carbon nanotubes (MWCNTs), can subsequently improve the overall performance of FPNG. A large electrical throughput (open circuit voltage ∼35 V with power density ∼2.43 µW/cm(3)) from PANI supplement added nanogenerator (PZP-FPNG) indicates that it is an effective means to replace the MWCNTs filler. The time constant (τ) estimated from the transient response of the capacitor charging curves signifying that the FPNGs are very much capable to charge the capacitors in very short time span (e.g., 3 V is accomplished in 50 s) and thus expected to be perfectly suitable in portable, wearable and flexible electronics devices. We demonstrate that FPNG can instantly lit up several commercial Light Emitting Diodes (LEDs) (15 red, 25 green, and 55 blue, individually) and power up several portable electronic gadgets, for example, wrist watch, calculator, and LCD screen. Thus, a realization of potential use of PANI in low-temperature-synthesized ZnS-NRs comprising piezoelectric based nanogenerator fabrication is experimentally verified so as to acquire a potential impact in sustainable energy applications. Beside this, wireless piezoelectric signal detection possibility is also worked out where a concept of self-powered smart sensor is introduced.

DNA-Assisted ß-phase Nucleation and Alignment of Molecular Dipoles in PVDF Film: A Realization of Self-Poled Bioinspired Flexible Polymer Nanogenerator for Portable Electronic Devices.

A flexible nanogenerator (NG) is fabricated with a poly(vinylidene fluoride) (PVDF) film, where deoxyribonucleic acid (DNA) is the agent for the electroactive ß-phase nucleation. Denatured DNA is co-operating to align the molecular -CH2/-CF2 dipoles of PVDF causing piezoelectricity without electrical poling. The NG is capable of harvesting energy from a variety of easily accessible mechanical stress such as human touch, machine vibration, football juggling, and walking. The NG exhibits high piezoelectric energy conversion efficiency facilitating the instant turn-on of several green or blue light-emitting diodes. The generated energy can be used to charge capacitors providing a wide scope for the design of self-powered portable devices.

Lead-free ZnSnO3/MWCNTs-based self-poled flexible hybrid nanogenerator for piezoelectric power generation.

A high-performance flexible piezoelectric hybrid nanogenerator (HNG) based on lead-free perovskite zinc stannate (ZnSnO3) nanocubes and polydimethylsiloxane (PDMS) composite with multiwall carbon nanotubes (MWCNTs) as supplement filling material is demonstrated. Even without any electrical poling treatment, the HNG possesses an open-circuit voltage of 40 V and a short-circuit current of 0.4 µA, respectively, under repeated human finger impact. It has been demonstrated that the output volume power density of 10.8 µW cm(-3) from a HNG can drive several colour light emitting diodes (LEDs) and a charge capacitor that powers up a calculator, indicating an effective means of energy harvesting power source with high energy conversion efficiency (∼1.17%) for portable electronic devices.