New Composites Derived from the Natural Fiber Polymers of Discarded Date Palm Surface and Pineapple Leaf Fibers for Thermal Insulation and Sound Absorption.

New composites made of natural fiber polymers such as wasted date palm surface fiber (DPSF) and pineapple leaf fibers (PALFs) are developed in an attempt to lower the environmental impact worldwide and, at the same time, produce eco-friendly insulation materials. Composite samples of different compositions are obtained using wood adhesive as a binder. Seven samples are prepared: two for the loose natural polymers of PALF and DPSF, two for the composites bound by single materials of PALF and DPSF using wood adhesive as a binder, and three composites of both materials and the binder with different compositions. Sound absorption coefficients (SACs) are obtained for bound and hybrid composite samples for a wide range of frequencies. Flexural moment tests are determined for these composites. A thermogravimetric analysis test (TGA) and the moisture content are obtained for the natural polymers and composites. The results show that the average range of thermal conductivity coefficient is 0.042-0.06 W/(m K), 0.052-0.075 W/(m K), and 0.054-0.07 W/(m K) for the loose fiber polymers, bound composites, and hybrid composites, respectively. The bound composites of DPSF have a very good sound absorption coefficient (>0.5) for almost all frequencies greater than 300 Hz, followed by the hybrid composite ones for frequencies greater than 1000 Hz (SAC > 0.5). The loose fiber polymers of PALF are thermally stable up to 218 °C. Most bound and hybrid composites have a good flexure modulus (6.47-64.16 MPa) and flexure stress (0.43-1.67 Mpa). The loose fiber polymers and bound and hybrid composites have a low moisture content below 4%. These characteristics of the newly developed sustainable and biodegradable fiber polymers and their composites are considered promising thermal insulation and sound absorption materials in replacing synthetic and petrochemical insulation materials in buildings and other engineering applications.

Sunflower and Watermelon Seeds and Their Hybrids with Pineapple Leaf Fibers as New Novel Thermal Insulation and Sound-Absorbing Materials.

Pineapple leaf fiber (PALF), striped sunflower seed fiber (SFSF), and watermelon seed (WMS) are considered natural waste polymer materials, which are biodegradable and sustainable. This study presents new novel thermal insulation and sound absorption materials using such waste as raw materials. PALF, SFSF, and WMS were used as loose, bound, and hybrid samples with different compositions to develop promising thermal insulation and sound-absorbing materials. Eleven sample boards were prepared: three were loose, three were bound, and five were hybrid between PALF with either SFSF or WMS. Wood adhesive was used as a binder for both the bound and hybrid sample boards. Laboratory scale sample boards of size 30 cm × 30 cm with variable thicknesses were prepared. The results show that the average thermal conductivity coefficient for the loose samples at the temperature range 20-80 °C is 0.04694 W/(m.K), 0.05611 W/(m.K), and 0.05976 W/m.K for PALF, SFSF, and WMS, respectively. Those for bound sample boards are 0.06344 W/(m.K), 0.07113 W/(m.K), and 0.08344 W/m.K for PALF, SFSF, and WMS, respectively. The hybrid ones between PALF and SFSF have 0.05921 W/m.K and 0.06845 W/(m.K) for two different compositions. The other hybrid between PALF and WMS has 0.06577 W/(m.K) and 0.07007 for two different compassions. The sound absorption coefficient for most of the bound and hybrid boards is above 0.5 and reaches higher values at some different frequencies. The thermogravimetric analysis for both SFSF and WMS shows that they are thermally stable up to 261 °C and 270 °C, respectively. The three-point bending moment test was also performed to test the mechanical properties of the bound and hybrid sample boards. It should be mentioned that using such waste materials as new sources of thermal insulation and sound absorption materials in buildings and other applications would lead the world to utilize the waste until zero agrowaste is reached, which will lower the environmental impact.

Effect of the Aspect Ratio and Tilt Angle on the Free Convection Heat Transfer Coefficient Inside Al2O3-Water-Filled Square Cuboid Enclosures.

This experimental study provides a comprehensive investigation of natural convection heat transfer inside shallow square cuboid enclosures filled with aluminum oxide-water nanofluid at four different volume concentrations: 0.0%, 0.2%, 0.4%, and 0.8%. Two square cuboid enclosures were used with sizes 30 × 30 × H cm3, where H is the inside thickness of the enclosures. This led to two different enclosure aspect ratios (κ = H/30 = 0.033 and 0.066). Four inclination angles to the horizontal position of the enclosures were used: 0°, 30°, 60°, and 90°. The crucial thermophysical properties of the synthetic nanofluid were obtained. The thermal conductivity of the nanofluid was measured experimentally at various volume concentrations. Furthermore, the viscosity and density were also measured experimentally at temperatures ranging from 15 to 40 °C as a function of the volume concentration. The heat transfer data were generated by heating the lower surface of the enclosure using a uniform flexible heat flux heater. The opposite surface was cooled using an air fan. The results of the experimental physical parameter measurements show that the percent of maximum deviation in thermal conductivity with those in the literature were 6.61% at a 1.0% volume concentration. The deviation of dynamic viscosity was between 0.21% and 16.36% at 0.1% and 1% volume concentrations, respectively, and for density it was 0.29% at 40 °C and a 1% volume concentration. The results showed up to a 27% enhancement in the Nusselt number at an angle of 60° and a 0.4% volume concentration in the largest aspect ratio (κ = 0.066). However, for the low aspect ratio enclosure (κ = 0.033), there was no noticeable improvement in heat transfer at any combination of volume concentration and inclination angle. The results show that the inclination angle is a significant factor in natural convection only for large aspect ratio enclosures. Furthermore, for large aspect ratio, the Nusselt number increased until the angle approached 60°, then it decreased again.

Thermophysical Properties of Hybrid Nanofluids and the Proposed Models: An Updated Comprehensive Study.

Thermal performance of energy conversion systems is one of the most important goals to improve the system's efficiency. Such thermal performance is strongly dependent on the thermophysical features of the applied fluids used in energy conversion systems. Thermal conductivity, specific heat in addition to dynamic viscosity are the properties that dramatically affect heat transfer characteristics. These features of hybrid nanofluids, as promising heat transfer fluids, are influenced by different constituents, including volume fraction, size of solid parts and temperature. In this article, the mentioned features of the nanofluids with hybrid nanostructures and the proposed models for these properties are reviewed. It is concluded that the increase in the volume fraction of solids causes improvement in thermal conductivity and dynamic viscosity, while the trend of variations in the specific heat depends on the base fluid. In addition, the increase in temperature increases the thermal conductivity while it decreases the dynamic viscosity. Moreover, as stated by the reviewed works, different approaches have applicability for modeling these properties with high accuracy, while intelligent algorithms, including artificial neural networks, are able to reach a higher precision compared with the correlations. In addition to the used method, some other factors, such as the model architecture, influence the reliability and exactness of the proposed models.

Free convection heat transfer inside square water-filled shallow enclosures.

Experimental study on free convection heat transfer was carried out inside shallow square enclosures filled with water. Two enclosures were used with size L × L × H (m3), where L and H are the side length and the inside thickness of the enclosure, respectively. Two different aspect ratios, κ = L/H, 7.143 and 12.0 were used. Constant heat flux boundary condition was applied at the bottom surface and stream of ambient air was applied at the top surface. Different values of constant heat fluxes were used as boundary conditions. For each aspect ratio of the enclosure, average Nusselt numbers were developed and correlated with the modified Rayleigh number. The results show that the heat transfer coefficient increases with the modified Rayleigh number with observed overlapping region between the two aspect ratios. A general overall correlation was developed using the aspect ratio as a parameter. The results also show that at the overlapping zone, the Nusselt number decreases as the aspect ratio increases for the fixed modified Rayleigh number.