Concrete Made with Iron Ore Tailings as a Fine Aggregate: A Step towards Sustainable Concrete.

The need for low-cost raw materials is driven by the fact that iron ore tailings, a prevalent kind of hazardous solid waste, have created major environmental issues. Although many studies have focused on using iron ore tailing (IOT) in concrete and have reported positive results, readers may find it difficult to accurately assess the behaviors of IOT in concrete due to the scattered nature of the information. Therefore, a comprehensive assessment of IOT in concrete is necessary. This paper thoroughly reviews the characteristics of concrete that contains IOT such as fresh properties, mechanical properties and durability at different age of curing. The outcome of this review indicates that by using IOT, concrete's mechanical properties and durability improved, but its flowability decreased. Compressive strength of concrete with 20% substitution of IOT is 14% more than reference concrete. Furthermore, up to 40% substitution of IOT produces concrete that has sufficient flowability and compactability. Scan electronic microscopy results indicate a weak interfacial transition zone (ITZ). The optimum IOT dosage is important since a greater dose may decrease the strength properties and durability owing to a lack of fluidity. Depending on the physical and chemical composition of IOT, the average value of optimum percentages ranges from 30 to 40%. The assessment also recommends areas of unsolved research for future investigations.

Overview of Concrete Performance Made with Waste Rubber Tires: A Step toward Sustainable Concrete.

Utilizing scrap tire rubber by incorporating it into concrete is a valuable option. Many researchers are interested in using rubber tire waste in concrete. The possible uses of rubber tires in concrete, however, are dispersed and unclear. Therefore, a compressive analysis is necessary to identify the benefits and drawbacks of rubber tires for concrete performance. For examination, the important areas of concrete freshness, durability, and strength properties were considered. Additionally, several treatments and a microstructure investigation were included. Although it has much promise, there are certain obstacles that prevent it from being used as an aggregate in large numbers, such as the rubber's weak structural strength and poor binding performance with the cement matrix. Rubber, however, exhibits mechanical strength comparable to reference concrete up to 20%. The evaluation also emphasizes the need for new research to advance rubberized concrete for future generations.

Eco-Friendly Incorporation of Crumb Rubber and Waste Bagasse Ash in Bituminous Concrete Mix.

The consumption of waste materials in the construction sector is a sustainable approach that helps in reducing the environmental pollution and decreases the construction cost. The present research work emphasizes the mechanical properties of bituminous concrete mix prepared with crumb rubber (CR) and waste sugarcane bagasse ash (SCBA). For the preparation of bituminous concrete mix specimens with CR and SCBA, the effective bitumen content was determined using the Marshall Mix design method. A total of 15 bituminous concrete mix specimens with 4%, 4.5%, 5%, 5.5% and 6% of bitumen content were prepared, and the effective bitumen content turned out to be 4.7%. The effect of five different CR samples of 2%, 4%, 6%, 8% and 10% by weight of total mix and SCBA samples of 25%, 50%, 75% and 100% by weight of filler were investigated on the performance of bituminous concrete. A total of 180 samples with different percentages of CR and SCBA were tested for indirect tensile strength (ITS) and Marshall Stability, and the results were compared with conventional bituminous concrete mix. It was observed that the stability values rose with an increase in CR percentage up to 6%, while the flow values rose as the percentage of SCBA increased in the mix. Maximum ITS results were observed at 4% CR and 25% SCBA replacement levels. However, a decrease in stability and ITS result was observed as the percentages of CR and SCBA increased beyond 4% and 25%, respectively. We concluded that the optimum CR and SCBA content of 4% and 25%, respectively, can be effectively used as a sustainable alternative in bituminous concrete mix.

Effects of Steel Fibers (SF) and Ground Granulated Blast Furnace Slag (GGBS) on Recycled Aggregate Concrete.

Recycled aggregate is a good option to be used in concrete production as a coarse aggregate that results in environmental benefits as well as sustainable development. However, recycled aggregate causes a reduction in the mechanical and durability performance of concrete. On the other hand, the removal of industrial waste would be considerably decreased if it could be incorporated into concrete production. One of these possibilities is the substitution of the cement by slag, which enhances the concrete poor properties of recycled aggregate concrete as well as provides a decrease in cement consumption, reducing carbon dioxide production, while resolving a waste management challenge. Furthermore, steel fiber was also added to enhance the tensile capacity of recycled aggregate concrete. The main goal of this study was to investigate the characteristics of concrete using ground granulated blast-furnace slag (GGBS) as a binding material on recycled aggregate fibers reinforced concrete (RAFRC). Mechanical performance was assessed through compressive strength and split tensile strength, while durability aspects were studied through water absorption, acid resistance, and dry shrinkage. The results detected from the different experiments depict that, at an optimum dose (40% RCA, 20%GGBS, and 2.0%), compressive and split tensile strength were 39% and 120% more than the reference concrete, respectively. Furthermore, acid resistance at the optimum dose was 36% more than the reference concrete. Furthermore, decreased water absorption and dry shrinkage cracks were observed with the substitution of GGBS into RAFRC.

Influence of Bentonite on Mechanical and Durability Properties of High-Calcium Fly Ash Geopolymer Concrete with Natural and Recycled Aggregates.

In this study, bentonite (a naturally occurring pozzolana) was incorporated as a partial replacement (up to 20%) for high-calcium fly ash (HCFA)-based geopolymeric natural aggregate concrete (GNAC) and geopolymeric recycled aggregate concrete (GRAC). The mechanical (compressive strength and splitting tensile strength), durability (chloride migration coefficient, water absorption, and acid attack resistance), and rheological properties (slump test, fresh density, and workability) were investigated. The results revealed that incorporation of bentonite (10 wt % with ordinary Portland cement) showed appreciable improvement in the strength and durability of both the GNAC and GRAC, though its effect is more significant for GRAC than the GNAC.

Failure Mechanism of Hybrid Steel Beams with Trapezoidal Corrugated-Web Non-Welded Inclined Folds.

Literature of Steel Beams with a thin-walled trapezoidal Corrugated Web (SBCWs) shows that the capacity of SBCWs is affected by both the fatigue cracks initiated along the inclined folds (IFs) and the maximal additional stress located in the middle of the IFs. An experimental investigation on the behaviour of hybrid SBCWs under flexure is presented in this paper. This study focuses on the effect of the welding IF between the web and flanges (IFs welded or non-welded), the horizontal-fold length (200, 260, and 350 mm), and transversal flange stiffeners on the failure mechanism of the SBCW under three line load. Accordingly, six hybrid specimens were fabricated, instrumented, and tested (five SBCW specimens and one specimen with a flat web). The test setup was designed to generate shear and a moment in the testing zone via three-point bending. The results indicated that non-welded IFs specimens with or without flange stiffeners failed owing to web tearing after web and flange local buckling. The failure mode of the specimen with continuous welding between the web and flanges was local flange buckling. Finally, the paper presents a comparison between the experimental results and the European Code to predict the capacity of the flange towards local buckling. It was concluded that the non-welding the IFs affected the inelastic behaviour and the capacity of the SBCWs. In addition, the bending resistance equations presented by EN 1993-1-5 can safely predict the test results of the non-welded inclined fold and yield a high safe variation.

Performance Evaluation of Cementitious Composites Incorporating Nano Graphite Platelets as Additive Carbon Material.

Nano graphite platelets (NGPs) belong to the carbon family and have a huge impact on the construction industry. NGPs are used as multi-functional fillers and have the potential to develop reinforcing within cementitious composites. In this paper, NGPs were incorporated in cementitious composites to investigate the effects of NGPs on the fresh, mechanical, durability, and microstructural properties of concrete. Five mixes were prepared with intrusion of NGPs (0%, 0.5%, 1.5%, 3%, and 5% by weight of cement). The properties studied involved workability, air content, hardened density, compressive strength, tensile strength, flexural strength, sorptivity, ultrasonic pulse velocity (UPV), water absorption, and external sulfate attack. The workability and percent air content decrease by 22.5% and 33.8%, respectively, for concrete with 5% NGPs compared to the control mix. The specimens containing 5% of NGPs revealed the hardened density, compressive, tensile, and flexural strength to increase by 11.4%, 38.5%, 31.6%, and 44.34%, respectively, compared to the control mix. The results revealed that the incorporation of 5%NGPs in cementitious composites reduces the sorptivity and water absorption by 32.2% and 73.9%, respectively, whereas, it increases the UPV value by 7.5% compared to the control mix. Furthermore, the incorporation of NGPs provided better resistance against external sulfate attacks. SEM-EDX spectroscopy was carried out to investigate its microstructural analysis.