Caregiver Knowledge, Attitude, and Behavior toward Care of Children with Cerebral Palsy: A Saudi Arabian Perspective.

The care of children with cerebral palsy (CP) requires a complex system of care that is not only dependent on health care resources, but is also strongly influenced by social and cultural attributes. Hence, it is important to explore the understanding and practices of caregivers within a regional perspective. This study was conducted to investigate the knowledge, attitude, and behavior (KAB) of parents with children diagnosed with CP in Saudi Arabia. A cross sectional survey was conducted on the caregivers of children with CP admitted for inpatient rehabilitation between October 2023 to January 2024. A total of 216 caregivers participated in this survey. About 82.9% of caregivers were the mothers of CP children, half (50.5%) were ≤36 years old, 53.7% were highly educated, and 89.2% lived in urban areas. More than half of the participants (57.7%) owned their homes. Regarding children, spastic quadriplegia was the most common type (46.3% of cases). Overall, the participants recorded good values for all variables for KAB. The mean value for attitude was higher (2.67 ± 0.20) when compared to behavior (2.49 ± 0.36) and knowledge (2.46 ± 0.25). Participants who had children with spastic quadriplegia CP reported lower behavior scores than their peers. Strategies with a special emphasis on improving the behaviors of caregivers for children with quadriplegia need to be adapted. Similarly, the living situations of families need to be taken into consideration given its significant association with the attitude of caregivers. A considerable lack of knowledge in handling emergency situations by caregivers signifies a gap in care, which could have potentially life-threatening consequences.

Evaluation of the Fracture Resistance of Different Designs of All-Resin Post and Core Systems: An In Vitro Study.

Introduction There is a growing demand for post and core systems that offer both ease of use and efficiency. Recently introduced dual-cure build-up and post cement materials exhibit properties similar to dentin. The objective of this laboratory experiment is to compare the fracture resistance among three distinct post and core systems and identify the locations of failures within each group. Material and methods This in vitro experimental study involved 30 epoxy resin-based blocks (Endo Training Bloc J, Dentsply Sirona, Ballaigues, Switzerland) divided into three groups: The first group was a post space preparation and restoration with a fiber post (RelyX™ Fiber Post, 3M ESPE, Saint Paul, Minnesota, United States) 1.6 mm in diameter and 10 mm in length (Group A) where core build-up and cementation were performed using a dual-cure build-up and cement for endodontic post resin material (Core X Flow, Dentsply DeTrey, Konstanz, Germany). The second group was a post space preparation and restoration using a dual-cure build-up and cement for endodontic post resin material, 10 mm in length filled with resin but without fiber post placement (Group B). The third group was where post space and core were filled and restored with a dual-cure build-up and cement for endodontic post resin material, 5 mm in length and without fiber post placement (Group C). Subsequently, samples were mounted and tested using a universal testing machine (Instron, Canton, Massachusetts, United States), and the fracture site was located. Results Significant differences were identified among the three groups, indicating the impact of both post length and type on fracture resistance (p-value <0.05). Group B exhibited the highest mean compressive strength resistance and maximum load at 899.3330 (N), followed by Group C at 848.9690 (N) and Group A at 751.9620 (N). The predominant failures in the samples were core fractures or debonding of the core material. Conclusion All-resin posts demonstrated high fracture resistance, unlike fiber posts which displayed inferior fracture resistance.

The Depth of Cure, Sorption and Solubility of Dual-Cured Bulk-Fill Restorative Materials.

This study aimed to examine depth of cure (DoC), mass change, water sorption and solubility of dual-cured bulk-fill restorative materials (Surfil One and Activa) in comparison with a light-cured bulk-fill composite (Filtek One Bulk-Fill) and a resin-modified glass ionomer (Fuji II LC). Twenty specimens were prepared of each material using stainless steel molds designed with a slot (8 × 4 × 2 mm) and irradiated for either 20 or 40 s. The Vickers hardness (VHN) was measured at every 0.5 mm to assess the DoC after 24 h of storage at 37 °C. The depth of cure was reported as the depth corresponding to 80% of the maximum Vickers hardness. Disc-shaped specimens were prepared of each material (n = 5) to investigate mass change, sorption and solubility after 4 months of water storage. The data were analyzed using a two-way and one-way analysis of variance (ANOVA) followed by the Tukey post hoc test (p ≤ 0.05). Fuji II LC had the greatest DoC while Activa had the lowest. The two different irradiation times did not demonstrate a significant difference in DoC for all dual-cured materials (p > 0.05). Fuji II LC had the highest sorption while Filtek One showed the lowest. Surefil One and Fuji II LC had a negative solubility. This study concluded that dual-cured materials showed different depth of cure values despite having the same setting reaction. Both materials exhibited a high water sorption, which might jeopardize their dimensional stability and effect their clinical performance.

Surface hardness and flexural strength of dual-cured bulk-fill restorative materials after solvent storage.

BACKGROUND: This study aimed to evaluate the surface hardness (VHN) and biaxial flexural strength (BFS) of dual-cured bulk-fill restorative materials after solvent storage. METHODS: Two dual-cured bulk-fill composites (Surefil One® and Activa™ Bioactive), a light-cured bulk-fill composite (Filtek One Bulk-Fill) and a resin-modified glass ionomer (Fuji II LC) were investigated. Surefil One and Activa were used in the dual-cure mode, all materials were handled according to manufacturer's instructions. For VHN determination, 12 specimens were prepared from each material and measured after 1 h (baseline), 1 d, 7 d and 30 d of storage in either water or 75% ethanol-water. For BFS test, 120 specimens were prepared (n = 30/material) and stored in water for either 1, 7 or 30 d before testing. Repeated measures MANOVA, two-way and one-way ANOVA followed by the Tukey post hoc test (p ≤ 0.05) were used to analyze the data. RESULTS: Filtek One had the highest VHN, while Activa had the lowest. All materials exhibited a significant increase in VHN after 1d of storage in water, except for Surefil One. After 30 d of storage, VHN increased significantly in water except for Activa, while ethanol storage caused a significant time-dependent reduction in all tested materials (p ≤ 0.05). Filtek One showed the highest BFS values (p ≤ 0.05). All the materials, except for Fuji II LC, exhibited no significant differences between 1 and 30 d BFS measurements (p > 0.05). CONCLUSIONS: Dual-cured materials had significantly lower VHN and BFS compared to the light-cured bulk-fill material. The low results of Activa VHN and Surefil One BFS, indicate that these materials should not be recommended in posterior stress-bearing areas.