The Difference in Performance and Compatibility between Crystalline and Amorphous Fillers in Mixed Matrix Membranes for Gas Separation (MMMs).

An increasing number of high-performing gas separation membranes is reported almost on a daily basis, yet only a few of them have reached commercialisation while the rest are still considered pure research outcomes. This is often attributable to a rapid change in the performance of these separation systems over a relatively short time. A common approach to address this issue is the development of mixed matrix membranes (MMMs). These hybrid systems typically utilise either crystalline or amorphous additives, so-called fillers, which are incorporated into polymeric membranes at different loadings, with the aim to improve and stabilise the final gas separation performance. After a general introduction to the most relevant models to describe the transport properties in MMMs, this review intends to investigate and discuss the main advantages and disadvantages derived from the inclusion of fillers of different morphologies. Particular emphasis will be given to the study of the compatibility at the interface between the filler and the matrix created by the two different classes of additives, the inorganic and crystalline fillers vs. their organic and amorphous counterparts. It will conclude with a brief summary of the main findings.

Tröger's Base Network Polymers of Intrinsic Microporosity (TB-PIMs) with Tunable Pore Size for Heterogeneous Catalysis.

Heterogeneous catalysis plays a pivotal role in the preparation of value-added chemicals, and it works more efficiently when combined with porous materials and supports. Because of that, a detailed assessment of porosity and pore size is essential when evaluating the performance of new heterogeneous catalysts. Herein, we report the synthesis and characterization of a series of novel microporous Tröger's base polymers and copolymers (TB-PIMs) with tunable pore size. The basicity of TB sites is exploited to catalyze the Knoevenagel condensation of benzaldehydes and malononitrile, and the dimension of the pores can be systematically adjusted with an appropriate selection of monomers and comonomers. The tunability of the pore size provides the enhanced accessibility of the catalytic sites for substrates, which leads to a great improvement in conversions, with the best results achieving completion in only 20 min. In addition, it enables the use of large benzaldehydes, which is prevented when using polymers with very small pores, typical of conventional PIMs. The catalytic reaction is more efficient than the corresponding homogeneous counterpart and is ultimately optimized with the addition of a small amount of a solvent, which facilitates the swelling of the pores and leads to a further improvement in the performance and to a better carbon economy. Molecular dynamic modeling of the copolymers' structures is employed to describe the swellability of flexible chains, helping the understanding of the improved performance and demonstrating the great potential of these novel materials.

CO2 Separation by Imide/Imine Organic Cages.

Invited for the cover of this issue are the groups of Valeria Amendola at the University of Pavia, Mariolino Carta at the University of Swansea, and Johannes C. Jansen at the CNR-ITM. The image depicts one of the novel imide/imine organic cages that were employed as fillers in mixed-matrix membranes for the selective separation of CO2 from N2 and CH4 . Read the full text of the article at 10.1002/chem.202201631.

CO2 Separation by Imide/Imine Organic Cages.

Two novel imide/imine-based organic cages have been prepared and studied as materials for the selective separation of CO2 from N2 and CH4 under vacuum swing adsorption conditions. Gas adsorption on the new compounds showed selectivity for CO2 over N2 and CH4 . The cages were also tested as fillers in mixed-matrix membranes for gas separation. Dense and robust membranes were obtained by loading the cages in either Matrimid® or PEEK-WC polymers. Improved gas-transport properties and selectivity for CO2 were achieved compared to the neat polymer membranes.

Adjustable Functionalization of Hyper-Cross-Linked Polymers of Intrinsic Microporosity for Enhanced CO2 Adsorption and Selectivity over N2 and CH4.

In this paper, we report the design, synthesis, and characterization of a series of hyper-cross-linked polymers of intrinsic microporosity (PIMs), with high CO2 uptake and good CO2/N2 and CO2/CH4 selectivity, which makes them competitive for carbon capture and biogas upgrading. The starting hydrocarbon polymers' backbones were functionalized with groups such as -NO2, -NH2, and -HSO3, with the aim of tuning their adsorption selectivity toward CO2 over nitrogen and methane. This led to a significant improvement in the performance in the potential separation of these gases. All polymers were characterized via Fourier transform infrared (FTIR) spectroscopy and 13C solid-state NMR to confirm their molecular structures and isothermal gas adsorption to assess their porosity, pore size distribution, and selectivity. The insertion of the functional groups resulted in an overall decrease in the porosity of the starting polymers, which was compensated with an improvement in the final CO2 uptake and selectivity over the chosen gases. The best uptakes were achieved with the sulfonated polymers, which reached up to 298 mg g-1 (6.77 mmol g-1), whereas the best CO2/N2 selectivities were recorded by the aminated polymers, which reached 26.5. Regarding CH4, the most interesting selectivities over CO2 were also obtained with the aminated PIMs, with values up to 8.6. The reason for the improvements was ascribed to a synergetic contribution of porosity, choice of the functional group, and optimal isosteric heat of adsorption of the materials.