Intracavitary Applicator for Sequential Delivery of Localized Hyperthermia Through Non-Metallic Uterine Tandem.

In this article, we report the design and demonstration of a flexible coaxial wire antenna with a low profile flexible choke for delivering localized hyperthermia (HT) treatment to the cervix through a custom designed uterine tandem applicator. Resistive and magnetic materials were investigated for determining the flexible choke design suited for intracavitary HT treatment at 915 MHz. Measurements of the intracavitary antenna with the flexible choke in tissue mimicking phantom and ex-vivo bovine muscle through the non-metallic uterine tandem prototype confirm the ability to deliver localized HT to the cervix at 915 MHz and 50 mm insertion depth.

Mechanical response of polyacrylamide breast tissue phantoms: Formulation, characterization and modeling.

In the context of breast cancer detection, mechanical imaging is an emerging technique for screening breast cancer. In view of its promise, it deserves a detailed investigation. Development of material that can emulate tissue behavior is essential for research. This work is concerned with the fabrication of polymeric specimens to capture the mechanical behavior of human breast tissues. Three types of tissue phantoms are fabricated: fat, glandular and ductal carcinoma tissues. The fabricated phantoms are compared to available human breast tissue data obtained through compression tests and stress relaxation tests. Further, the fabricated tissue phantoms are subjected to stress relaxation tests to characterize their viscoelastic response. A finite strain viscoelastic constitute model is proposed to describe the mechanical response of the breast tissue phantoms. The model is calibrated using experimental data for phantom tissue specimens. Both phantom tissue specimens and model predictions show reasonable trends. The phantom tissues and model may be of utility in developing mechanical imaging setups.

Design of Site-Specific Microwave Phased Array Hyperthermia Applicators Using 434 MHz Reduced Cavity-Backed Patch Antenna.

Cancers of the neck, breast, and lower extremities are common malignancies diagnosed in India with a higher incidence of advanced-stage disease. Phased array (PA) applicators reported for hyperthermia treatment (HT) of the breast have small focal region and high cross-coupling, and those reported for lower extremities provide regional heating and limited steering. In this study, we present the numerical design of site-specific PA applicators for HT of large solid tumors in the neck, breast, and lower extremities using a miniaturized 434 MHz cavity-backed water-loaded patch antenna. The fabricated antenna has 38 × 36 mm2 aperture, more than 90% power coupling, 25 MHz bandwidth, and good agreement between simulated and measured specific absorption rate (SAR) in phantom. The site-specific applicators demonstrated less power reflection (<-17.9 dB) and cross-coupling (<-26.8 dB) for 5 mm inter-ring spacing. SAR indicators for 64 cc tumor at varying locations in simplified layered three-dimensional (3D) tissue models of the neck, breast, and leg showed average power absorption ratio (aPAratio ) ≥ 3.16, target to hotspot quotient (THQ) ≥ 0.57, 25% iso-SAR coverage (TC25 ) ≥ 81%, and 50% iso-SAR coverage (TC50 ) ≥51.8%. Simulation results of site-specific applicators for 3D inhomogeneous patient models showed aPAratio ≥ 5.98, THQ ≥ 0.9, TC50 ≥ 86%, and 100% TC25 for all sites. It is concluded that the 434 MHz miniaturized cavity-backed patch antenna can be used to develop high-density PA applicators with 12-24 antennas for HT of large solid tumors (≥4 cm) in the neck, breast, and lower extremities with 3D steering ability and less cross-coupling (≤-26.8 dB). © 2020 Bioelectromagnetics Society.

Study of absorption of radio frequency field by gold nanoparticles and nanoclusters in biological medium.

Gold nanoparticles (AuNPs) and gold nanoclusters (AuNCs) are gaining interest in medical diagnosis and therapy as they are bio-compatible and are easy to functionalize. Their interaction with radiofrequency (RF) field for hyperthermia treatment is ambiguous and needs further investigation. A systematic study of the absorption of capacitive RF field by AuNPs and AuNCs dispersed in phosphate-buffered saline (PBS) is reported here in tissue mimicking phantom. The stability of AuNPs and AuNCs dispersed in PBS was confirmed for a range of pH and temperature expected during RF hyperthermia treatment. Colloidal gold solutions with AuNPs (10 nm) and AuNCs (2 nm), and control, i.e. PBS without nanogold, were loaded individually in 3 ml wells in a tissue phantom. Phantom heating was carried out using 27 MHz short-wave diathermy equipment at 200 and 400 W for control and colloidal gold solutions. Experiments were conducted for colloidal gold at varying gold concentrations (10-100 µg/ml). Temperature rise measured in the phantom wells did not show dependence on the concentration and size of the AuNPs. Furthermore, temperature rise recorded in the control was comparable with the measurements recorded in both nanogold suspensions (2, 10 nm). Dielectric property measurements of control and colloidal gold showed <3% difference in electrical conductivity between the control and colloidal gold for both nanoparticle sizes. From the measurements, it is concluded that AuNPs and AuNCs do not enhance the absorption of RF-capacitive field and power absorption observed in the biological medium is due to the ions present in the medium.

Pre-Clinical Testing of Microwave Radiometer and a Pilot Study on the Screening Inflammation of Knee Joints.

This article presents the pre-clinical evaluation of our custom-built, single-band microwave radiometer centered at 1.3 GHz for deep tissue thermometry, and a pilot study on volunteers for passive detection of inflammation in knee joints. The electromagnetic (EM) compatibility of the battery-operated radiometer for clinical use was assessed as per International Special Committee on Radio Interference (CISPR) 22 standard. The ability to detect inflammation in knee joints was assessed using a substrate integrated waveguide antenna connected to the radiometer. EM compatibility tests carried out in the laboratory indicated device immunity to intentional radiated interference up to -20 dBm injected power in the global system for mobile communication frequency band, and pre-compliance to CISPR 22 standard. Radiometer temperature measurements recorded at the lateral and medial aspects of both knees of 41 volunteers indicated mean temperature greater than 33°C for the diseased sites compared with the mean temperature of 28°C measured for the healthy sites. One-way analysis of variance statistics indicated significantly (P < 0.005) higher radiometer temperature at the diseased sites unlike the healthy sites. Thus, the EM pre-compliance of the device and the potential to measure deep tissue inflammation were demonstrated. Bioelectromagnetics. 2019;40:402-411. © 2019 Bioelectromagnetics Society.

Non-contact in situ microwave material measurements for high temperature process monitoring.

Non-contact real time microwave measurement and signal analysis techniques to extract high temperature material parameters from the mono-static reflections gathered by a compact air cooled corrugated horn are presented in this work. Non-contact in situ microwave measurements gathered over 20-24 GHz inside a closed furnace were processed to identify the thermodynamic phase change temperature of metal and glass melts. The melting point of aluminum alloy and glass transition of a borosilicate glass matrix extracted from the time gated and processed microwave measurements were in good agreement with differential scanning calorimetry measurements. Thus, the ability to measure high temperature material process parameters using non-contact microwave measurements is demonstrated.

Multi-physics modeling to study the influence of tissue compression and cold stress on enhancing breast tumor detection using microwave radiometry.

The influence of tissue compression and external thermal modulation on passive detection of breast tumors using medical microwave radiometry was investigated using multi-physics numerical modeling. A three-dimensional numerical model of the pendant breast with 10 and 6 mm diameter tumors at varying depths (15 mm, 30 mm) was analyzed at thermodynamic equilibrium using a circular waveguide as the receive antenna. The contrast in the brightness temperature, ΔTB , between the unhealthy and healthy breasts was found to be significantly more for breast compression alone, compared to thermal modulation of the tissue surface, irrespective of tissue composition, tumor size, and depth. The study also concludes that small deep-seated tumor with very low metabolic activity that is not detectable by a radiometer with 0.1 °C sensitivity could be detected under breast compression and short duration cold stress. Thus, detection of deep-seated breast tumors can be significantly improved under controlled tissue compression with an optional cold stress. Bioelectromagnetics. © 2019 Bioelectromagnetics Society.

Ultrasound-Based Regularized Log Spectral Difference Method For Monitoring Microwave Hyperthermia.

The feasibility of using normalized cumulative difference attenuation (NCDA) map for tracking the spatial and temporal evolution of temperature during microwave hyperthermia experiment on in-vitro phantoms is explored in this study. The NCDA maps were estimated from the beamformed ultrasound radio frequency (RF) data using a regularized log spectral difference (RLSD) technique. The NCDA maps were estimated at different time instants for the entire period of the experiment. The contour maps of the NCDA and the ground truth temperature map, obtained using an infra-red(IR) thermal camera corresponding to the ultrasound imaging plane, showed that NCDA was able to locate the axial and lateral co-ordinates of the hotspot with the error of <; 1.5 mm axially and <; 0.1 mm laterally. The error in the estimated hotspot area was less than 8 %. This preliminary in-vitro study suggests that NCDA maps estimated using RLSD may have potential in evaluating the spatio-temporal evolution of temperature and may help in the development of ultrasound-based image-guided temperature monitoring system for microwave hyperthermia.

Design and characterisation of miniaturised cavity-backed patch antenna for microwave hyperthermia.

PURPOSE: The aim of this study was to describe the design and characterisation of a miniaturised 434 MHz patch antenna enclosed in a metal cavity for microwave hyperthermia treatment of cancer. MATERIALS AND METHODS: Electromagnetic (EM) field distribution in the near field of a microstrip patch irradiating body tissue was studied using finite element method (FEM) simulations. Antenna miniaturisation was achieved through dielectric loading with very high permittivity, metal enclosure, patch folding and shorting post. Frequency dependent electrical properties of materials were incorporated wherever appropriate using dispersion model and measurements. Antenna return loss and specific absorption rate (SAR) at 434 MHz were measured on muscle phantoms for characterisation. RESULTS: The design was progressively optimised to yield a compact 434 MHz patch (22 mm × 8.8 mm × 10 mm) inside a metal cavity (40 mm × 12 mm) with integrated coupling water bolus (35 mm). The fabricated antenna with integrated water bolus was self resonant at 434 MHz without load, and has better than -10 dB return loss (S11) with 13-20 MHz bandwidth on two different phantoms. SAR at 434 MHz measured using an infrared (IR) thermal camera on split phantoms indicated penetration depth for -3 dB SAR as 8.25 mm compared to 8.87 mm for simulation. The simulated and measured SAR coverage along phantom depth was 3.09 cm(2) and 3.21 cm(2) respectively at -3 dB, and 6.42 cm(2) and 9.07 cm(2) respectively at -6 dB. SAR full width at half maximum (FWHM) at 5 mm and 20 mm depths were 54.68 mm and 51.18 mm respectively in simulation, and 49.47 mm and 43.75 mm respectively in experiments. Performance comparison of the cavity-backed patch indicates more than 89% co-polarisation and higher directivity which resulted in deeper penetration compared to the patch applicators of similar or larger size proposed for hyperthermia treatment of cancer. CONCLUSION: The fabricated cavity-backed applicator is self-resonant at 434 MHz with a negligible shift in resonance when coupled to different phantoms, Δf/f0 less than 1.16%. IR thermography-based SAR measurements indicated that the -3 dB SAR of the cavity-backed aperture antenna covered the radiating aperture surface at 5 mm and 20 mm depths. It can be concluded that the compact cavity-backed patch antenna has stable resonance, higher directivity and low cross polarisation, and is suitable for design of microwave hyperthermia array applicators with adjustable heating pattern for superficial and/or deep tissue heating.

Breast tissue phantoms to assist compression study for cancer detection using microwave radiometry.

Microwave radiometry is a passive imaging modality proposed for breast cancer detection without the need for ionizing radiation. Detection of breast tumor using radiometry is challenging as the intensity of thermal radiation received by the antenna is influenced by tumor stage, location, physiological conditions and the imaging setup. The controllable parameters for setting up a good imaging modality for early detection of breast cancer are ambient temperature (Ta), convection cooling of tissue surface (h), and tissue compression (c). Amongst these parameters tissue compression plays an important role since reducing the breast thickness increases visibility. In this work, fabrication of hydrogel breast tissue phantoms with varying concentrations of polyvinyl alcohol (PVAL) is carried out to mimic breast fat and glandular tissue properties for compression study. The phantoms were subjected to compression to investigate the mechanical properties for varying PVAL concentrations. A 3D numerical model was developed for phantom tissue compression simulations. Simulated tissue compression results were compared with phantom measurements for model validation.

A compact microwave patch applicator for hyperthermia treatment of cancer.

Design and development of a compact microstrip C-type patch applicator for hyperthermia treatment of cancer is presented. The patch antenna is optimized for resonance at 434 MHz, return loss (S11) better than -15dB and co-polarized electric field in tissue. Effect of water bolus thickness on power delivery is studied for improved power coupling. Numerical simulations for antenna design optimization carried out using EM simulation software, Ansys HFSS(®), USA were experimentally verified. The effective field coverage for the optimized patch antenna and experimental results indicate that the compact antenna resonates at ISM frequency 434 MHz with better than -15 dB power coupling.

Preclinical assessment of comfort and secure fit of thermobrachytherapy surface applicator (TBSA) on volunteer subjects.

A thermobrachytherapy surface applicator (TBSA) was developed for simultaneous heat and brachytherapy treatment of chest wall (CW) recurrence of breast cancer. The ability to comfortably secure the applicator over the upper torso relative to the CW target throughout treatment is assessed on volunteers. Male and postmastectomy female volunteers were enrolled to evaluate applicator secure fit to CW. Female subjects with intact breast were also enrolled to assess the ability to treat challenging cases. Magnetic resonance (MR) images of volunteers wearing a TBSA over the upper torso were acquired once every 15 minutes for 90 minutes. Applicator displacement over this time period required for treatment preplanning and delivery was assessed using MR visible markers. Applicator comfort and tolerability were assessed using a questionnaire. Probability estimates of applicator displacements were used to investigate dosimetric impact for the worst-case variation in radiation source-to-skin distance for 5 and 10 mm deep targets spread 17 × 13 cm on a torso phantom. Average and median displacements along lateral and radial directions were less than 1.2 mm over 90 minutes for all volunteers. Maximum lateral and radial displacements were measured to be less than 1 and 1.5 mm, respectively, for all CW volunteers and less than 2 mm for intact breast volunteers, excluding outliers. No complaint of pain or discomfort was reported. Phantom treatment planning for the maximum displacement of 2 mm indicated < 10% increase in skin dose with < 5% loss of homogeneity index (HI) for -2 mm uniform HDR source displacement. For +2 mm uniform displacement, skin dose decreased and HI increased by 20%. The volunteer study demonstrated that such large and uniform displacements should be rare for CW subjects, and the measured variation is expected to be low for multifraction conformal brachytherapy treatment.

Utility of treatment planning for thermochemotherapy treatment of nonmuscle invasive bladder carcinoma.

PURPOSE: A recently completed Phase I clinical trial combined concurrent Mitomycin-C chemotherapy with deep regional heating using BSD-2000 Sigma-Ellipse applicator (BSD Corporation, Salt Lake City, UT, U.S.A.) for the treatment of nonmuscle invasive bladder cancer. This work presents a new treatment planning approach, and demonstrates potential impact of this approach on improvement of treatment quality. METHODS: This study retrospectively analyzes a subset of five patients on the trial. For each treatment, expert operators selected "clinical-optimal" settings based on simple model calculation on the BSD-2000 control console. Computed tomography (CT) scans acquired prior to treatment were segmented to create finite element patient models for retrospective simulations with Sigma-HyperPlan (Dr. Sennewald Medizintechnik GmbH, Munchen, Germany). Since Sigma-HyperPlan does not account for the convective nature of heat transfer within a fluid filled bladder, an effective thermal conductivity for bladder was introduced. This effective thermal conductivity value was determined by comparing simulation results with clinical measurements of bladder and rectum temperatures. Regions of predicted high temperature in normal tissues were compared with patient complaints during treatment. Treatment results using "computed-optimal" settings from the planning system were compared with clinical results using clinical-optimal settings to evaluate potential of treatment improvement by reducing hot spot volume. RESULTS: For all five patients, retrospective treatment planning indicated improved matches between simulated and measured bladder temperatures with increasing effective thermal conductivity. The differences were mostly within 1.3 °C when using an effective thermal conductivity value above 10 W/K/m. Changes in effective bladder thermal conductivity affected surrounding normal tissues within a distance of ∼1.5 cm from the bladder wall. Rectal temperature differences between simulation and measurement were large due to sensitivity to the sampling locations in rectum. The predicted bladder T90 correlated well with single-point bladder temperature measurement. Hot spot locations predicted by the simulation agreed qualitatively with patient complaints during treatment. Furthermore, comparison between the temperature distributions with clinical and computed-optimal settings demonstrated that the computed-optimal settings resulted in substantially reduced hot spot volumes. CONCLUSIONS: Determination of an effective thermal conductivity value for fluid filled bladder was essential for matching simulation and treatment temperatures. Prospectively planning patients using the effective thermal conductivity determined in this work can potentially improve treatment efficacy (compared to manual operator adjustments) by potentially lower discomfort from reduced hot spots in normal tissue.

Comprehensive analysis of the Cramer-Rao bounds for magnetic resonance temperature change measurement in fat-water voxels using multi-echo imaging.

OBJECT: The aim of this paper is to characterize the noise propagation for MRI temperature change measurement with emphasis on finding the best echo time combinations that yield the lowest temperature noise. MATERIALS AND METHODS: A Cramer-Rao lower-bound (CRLB) calculation was used to estimate the temperature noise for a model of the MR signal in fat-water voxels. The temperature noise CRLB was then used to find a set of echo times that gave the lowest temperature change noise for a range of fat-water frequency differences, temperature changes, fat/water signal ratios, and T2* values. CRLB estimates were verified by Monte Carlo simulation and in phantoms using images acquired in a 1.5 T magnet. RESULTS: Results show that regions exist where the CRLB predicts minimal temperature variation as a function of the other variables. The results also indicate that the CRLB values calculated in this paper provide excellent guidance for predicting the variation of temperature measurements due to changes in the signal parameters. For three echo scans, the best noise characteristics are seen for TE values of 20.71, 23.71, and 26.71 ms. Results for five and seven echo scans are also presented in the text. CONCLUSION: The results present a comprehensive analysis of the effects of different scan parameters on temperature noise, potentially benefiting the selection of scan parameters for clinical MRI thermometry.

Vesicoureteral reflux in children: a phantom study of microwave heating and radiometric thermometry of pediatric bladder.

We have investigated the use of microwave heating and radiometry to safely heat urine inside a pediatric bladder. The medical application for this research is to create a safe and reliable method to detect vesicoureteral reflux, a pediatric disorder, where urine flow is reversed and flows from the bladder back up into the kidney. Using fat and muscle tissue models, we have performed both experimental and numerical simulations of a pediatric bladder model using planar dual concentric conductor microstrip antennas at 915 MHz for microwave heating. A planar elliptical antenna connected to a 500 MHz bandwidth microwave radiometer centered at 3.5 GHz was used for noninvasive temperature measurement inside tissue. Temperatures were measured in the phantom models at points during the experiment with implanted fiberoptic sensors, and 2-D distributions in cut planes at depth in the phantom with an infrared camera at the end of the experiment. Cycling between 20 s with 20 Watts power for heating, and 10 s without power to allow for undisturbed microwave radiometry measurements, the experimental results show that the target tissue temperature inside the phantom increases fast and that the radiometer provides useful measurements of spatially averaged temperature of the illuminated volume. The presented numerical and experimental results show excellent concordance, which confirms that the proposed system for microwave heating and radiometry is applicable for safe and reliable heating of pediatric bladder.

Detection of vesicoureteral reflux using microwave radiometry-system characterization with tissue phantoms.

Microwave (MW) radiometry is proposed for passive monitoring of kidney temperature to detect vesicoureteral reflux (VUR) of urine that is externally heated by a MW hyperthermia device and thereafter reflows from the bladder to kidneys during reflux. Here, we characterize in tissue-mimicking phantoms the performance of a 1.375 GHz radiometry system connected to an electromagnetically (EM) shielded microstrip log spiral antenna optimized for VUR detection. Phantom EM properties are characterized using a coaxial dielectric probe and network analyzer (NA). Power reflection and receive patterns of the antenna are measured in layered tissue phantom. Receiver spectral measurements are used to assess EM shielding provided by a metal cup surrounding the antenna. Radiometer and fiberoptic temperature data are recorded for varying volumes (10-30 mL) and temperaturesg (40-46°C) of the urine phantom at 35 mm depth surrounded by 36.5°C muscle phantom. Directional receive pattern with about 5% power spectral density at 35 mm target depth and better than -10 dB return loss from tissue load are measured for the antenna. Antenna measurements demonstrate no deterioration in power reception and effective EM shielding in the presence of the metal cup. Radiometry power measurements are in excellent agreement with the temperature of the kidney phantom. Laboratory testing of the radiometry system in temperature-controlled phantoms supports the feasibility of passive kidney thermometry for VUR detection.

Microwave Radiometry for Non-Invasive Detection of Vesicoureteral Reflux (VUR) Following Bladder Warming.

BACKGROUND: Vesicoureteral reflux (VUR) is a serious health problem leading to renal scarring in children. Current VUR detection involves traumatic x-ray imaging of kidneys following injection of contrast agent into bladder via invasive Foley catheter. We present an alternative non-invasive approach for detecting VUR by radiometric monitoring of kidney temperature while gently warming the bladder. METHODS: We report the design and testing of: i) 915MHz square slot antenna array for heating bladder, ii) EMI-shielded log spiral microstrip receive antenna, iii) high-sensitivity 1.375GHz total power radiometer, iv) power modulation approach to increase urine temperature relative to overlying perfused tissues, and v) invivo porcine experiments characterizing bladder heating and radiometric temperature of aaline filled 30mL balloon "kidney" implanted 3-4cm deep in thorax and varied 2-6°C from core temperature. RESULTS: SAR distributions are presented for two novel antennas designed to heat bladder and monitor deep kidney temperatures radiometrically. We demonstrate the ability to heat 180mL saline in in vivo porcine bladder to 40-44°C while maintaining overlying tissues <38°C using time-modulated square slot antennas coupled to the abdomen with room temperature water pad. Pathologic evaluations confirmed lack of acute thermal damage in pelvic tissues for up to three 20min bladder heat exposures. The radiometer clearly recorded 2-6°C changes of 30mL "kidney" targets at depth in 34°C invivo pig thorax. CONCLUSION: A 915MHz antenna array can gently warm in vivo pig bladder without toxicity while a 1.375GHz radiometer with log spiral receive antenna detects ≥2°C rise in 30mL "urine" located 3-4cm deep in thorax, demonstrating more than sufficient sensitivity to detect Grade 4-5 reflux of warmed urine for non-invasive detection of VUR.

Conformal microwave array (CMA) applicators for hyperthermia of diffuse chest wall recurrence.

PURPOSE: This article summarises the evolution of microwave array applicators for heating large area chest wall disease as an adjuvant to external beam radiation, systemic chemotherapy, and potentially simultaneous brachytherapy. METHODS: Current devices used for thermotherapy of chest wall recurrence are reviewed. The largest conformal array applicator to date is evaluated in four studies: (1) ability to conform to the torso is demonstrated with a CT scan of a torso phantom and MR scan of the conformal water bolus component on a mastectomy patient; (2) specific absorption rate (SAR) and temperature distributions are calculated with electromagnetic and thermal simulation software for a mastectomy patient; (3) SAR patterns are measured with a scanning SAR probe in liquid muscle phantom for a buried coplanar waveguide CMA; and (4) heating patterns and patient tolerance of CMA applicators are characterised in a clinical pilot study with 13 patients. RESULTS: CT and MR scans demonstrate excellent conformity of CMA applicators to contoured anatomy. Simulations demonstrate effective control of heating over contoured anatomy. Measurements confirm effective coverage of large treatment areas with no gaps. In 42 hyperthermia treatments, CMA applicators provided well-tolerated effective heating of up to 500 cm(2) regions, achieving target temperatures of T(min) = 41.4 ± 0.7°C, T(90) = 42.1 ± 0.6°C, T(ave) = 42.8 ± 0.6°C, and T(max) = 44.3 ± 0.8°C as measured in an average of 90 points per treatment. CONCLUSION: The CMA applicator is an effective thermal therapy device for heating large-area superficial disease such as diffuse chest wall recurrence. It is able to cover over three times the treatment area of conventional hyperthermia devices while conforming to typical body contours.

Modeling the detectability of vesicoureteral reflux using microwave radiometry.

We present the modeling efforts on antenna design, frequency selection and receiver sensitivity estimation to detect vesicoureteral reflux (VUR) using microwave (MW) radiometry as warm urine from the bladder maintained at fever range temperature using a MW hyperthermia device reflows into the kidneys. The radiometer center frequency (f(c)), frequency band (Deltaf) and aperture radius (r(a)) of the physical antenna for kidney temperature monitoring are determined using a simplified universal antenna model with a circular aperture. Anatomical information extracted from the computed tomography (CT) images of children aged 4-6 years is used to construct a layered 3D tissue model. Radiometric antenna efficiency is evaluated in terms of the ratio of the power collected from the target at depth to the total power received by the antenna (eta). The power ratio of the theoretical antenna is used to design a microstrip log spiral antenna with directional radiation pattern over f(c) +/- Deltaf/2. Power received by the log spiral from the deep target is enhanced using a thin low-loss dielectric matching layer. A cylindrical metal cup is proposed to shield the antenna from electromagnetic interference (EMI). Transient thermal simulations are carried out to determine the minimum detectable change in the antenna brightness temperature (deltaT(B)) for 15-25 mL urine refluxes at 40-42 degrees C located 35 mm from the skin surface. Theoretical antenna simulations indicate maximum eta over 1.1-1.6 GHz for r(a) = 30-40 mm. Simulations of the 35 mm radius tapered log spiral yielded a higher power ratio over f(c) +/- Deltaf/2 for the 35-40 mm deep targets in the presence of an optimal matching layer. Radiometric temperature calculations indicate deltaT(B) 0.1 K for the 15 mL urine at 40 degrees C and 35 mm depth. Higher eta and deltaT(B) were observed for the antenna and matching layer inside the metal cup. Reflection measurements of the log spiral in a saline phantom are in agreement with the simulation data. The numerical study suggests that a radiometer with f(c) = 1.35 GHz, Deltaf = 500 MHz and detector sensitivity better than 0.1 K would be the appropriate tool to noninvasively detect VUR using the log spiral antenna.

Design of a water coupling bolus with improved flow distribution for multi-element superficial hyperthermia applicators.

A water bolus used in superficial hyperthermia couples the electromagnetic (EM) or acoustic energy into the target tissue and cools the tissue surface to minimise thermal hotspots and patient discomfort during treatment. Parametric analyses of the fluid pressure inside the bolus computed using 3D fluid dynamics simulations are used in this study to determine a bolus design with improved flow and surface temperature distributions for large area superficial heat applicators. The simulation results are used in the design and fabrication of a 19 x 32 cm prototype bolus with dual input-dual output (DIDO) flow channels. Sequential thermal images of the bolus surface temperature recorded for a step change in the circulating water temperature are used to assess steady state flow and surface temperature distributions across the bolus. Modelling and measurement data indicate substantial improvement in bolus flow and surface temperature distributions when changing from the previous single input-single output (SISO) to DIDO configuration. Temperature variation across the bolus at steady state was measured to be less than 0.8 degrees C for the DIDO bolus compared to 1.5 degrees C for the SISO water bolus. The new DIDO bolus configuration maintains a nearly uniform flow distribution and low variation in surface temperature over a large area typically treated in superficial hyperthermia.