One-Pot Synthesis of Pd Nanoparticles Supported on Carbide-Derived Carbon for Oxygen Reduction Reaction.

We explored two methods for synthesizing Pd nanoparticles using three different carbide-derived carbon (CDC) support materials, one of which was nitrogen-doped. These materials were studied for oxygen reduction reaction (ORR) in 0.1 M KOH solution, and the resulting CDC/Pd catalysts were characterized using TEM, XRD, and XPS. The citrate method and the polyol method using polyvinylpyrrolidone (PVP) as a capping agent were employed to elucidate the impact of the support material on the final catalyst. The N-doping of the CDC material resulted in smaller Pd nanoparticles, but only in the case of the citrate method. This suggests that the influence of support is weaker when using the polyol method. The citrate method with CDC1, which is predominantly microporous, led to a higher degree of agglomeration and formation of larger particles in comparison to supports, which possessed a higher degree of mesoporosity. We achieved smaller Pd particle sizes using citrate and NaBH4 compared to the ethylene glycol PVP method. Pd deposited on CDC2 and CDC3 supports showed similar specific activity (SA), suggesting that the N-doping did not significantly influence the ORR process. The highest SA value was observed for CDC1/Pd_Cit, which could be attributed to the formation of larger Pd particles and agglomerates.

Iron Triad-Based Bimetallic M-N-C Nanomaterials as Highly Active Bifunctional Oxygen Electrocatalysts.

The use of precious metal electrocatalysts in clean electrochemical energy conversion and storage applications is widespread, but the sustainability of these materials, in terms of their availability and cost, is constrained. In this research, iron triad-based bimetallic nitrogen-doped carbon (M-N-C) materials were investigated as potential bifunctional electrocatalysts for the oxygen reduction reaction (ORR) and oxygen evolution reaction (OER). The synthesis of bimetallic FeCo-N-C, CoNi-N-C, and FeNi-N-C catalysts involved a precisely optimized carbonization process of their respective metal-organic precursors. Comprehensive structural analysis was undertaken to elucidate the morphology of the prepared M-N-C materials, while their electrocatalytic performance was assessed through cyclic voltammetry and rotating disk electrode measurements in a 0.1 M KOH solution. All bimetallic catalyst materials demonstrated impressive bifunctional electrocatalytic performance in both the ORR and the OER. However, the FeNi-N-C catalyst proved notably more stable, particularly in the OER conditions. Employed as a bifunctional catalyst for ORR/OER within a customized zinc-air battery, FeNi-N-C exhibited a remarkable discharge-charge voltage gap of only 0.86 V, alongside a peak power density of 60 mW cm-2. The outstanding stability of FeNi-N-C, operational for about 55 h at 2 mA cm-2, highlights its robustness for prolonged application.

Peat-Derived ZnCl2-Activated Ultramicroporous Carbon Materials for Hydrogen Adsorption.

Highly microporous adsorbents have been under considerable scrutiny for efficient adsorptive storage of H2. Of specific interest are sustainable, chemically activated, microporous carbon adsorbents, especially from renewable and organic precursor materials. In this article, six peat-derived microporous carbon materials were synthesized by chemical activation with ZnCl2. N2 and CO2 gas adsorption data were measured and simultaneously fitted with the 2D-NLDFT-HS model. Thus, based on the obtained results, the use of a low ratio of ZnCl2 for chemical activation of peat-derived carbon yields highly ultramicroporous carbons which are able to adsorb up to 83% of the maximal adsorbed amount of adsorbed H2 already at 1 bar at 77 K. This is accompanied by the high ratio of micropores, 99%, even at high specific surface area of 1260 m2 g-1, exhibited by the peat-derived carbon activated at 973 K using a 1:2 ZnCl2 to peat mass ratio. These results show the potential of using low concentrations of ZnCl2 as an activating agent to synthesize highly ultramicroporous carbon materials with suitable pore characteristics for the efficient low-pressure adsorption of H2.

Cobalt Phthalocyanine-Doped Polymer-Based Electrocatalyst for Rechargeable Zinc-Air Batteries.

Rechargeable zinc-air batteries (RZAB) have gained significant attention as potential energy storage devices due to their high energy density, cost-effectiveness, and to the fact that they are environmentally safe. However, the practical implementation of RZABs has been impeded by challenges such as sluggish oxygen reduction reaction (ORR) and oxygen evolution reaction (OER), including poor cyclability. Herein, we report the preparation of cobalt- and nitrogen-doped porous carbon derived from phloroglucinol-formaldehyde polymer networks with 2-methyl imidazole and cobalt phthalocyanine as precursors for nitrogen and cobalt. The CoN-PC-2 catalyst prepared in this study exhibits commendable electrocatalytic activity for both ORR and OER, evidenced by a half-wave potential of 0.81 V and Ej=10 of 1.70 V. Moreover, the catalyst demonstrates outstanding performance in zinc-air batteries, achieving a peak power density of 158 mW cm-2 and displaying excellent stability during charge-discharge cycles. The findings from this study aim to provide valuable insights and guidelines for further research and the development of hierarchical micro-mesoporous carbon materials from polymer networks, facilitating their potential commercialisation and widespread deployment in energy storage applications.

Iron, Cobalt, and Nickel Phthalocyanine Tri-Doped Electrospun Carbon Nanofibre-Based Catalyst for Rechargeable Zinc-Air Battery Air Electrode.

The goal of achieving the large-scale production of zero-emission vehicles by 2035 will create high expectations for electric vehicle (EV) development and availability. Currently, a major problem is the lack of suitable batteries and battery materials in large quantities. The rechargeable zinc-air battery (RZAB) is a promising energy-storage technology for EVs due to the environmental friendliness and low production cost. Herein, iron, cobalt, and nickel phthalocyanine tri-doped electrospun carbon nanofibre-based (FeCoNi-CNF) catalyst material is presented as an affordable and promising alternative to Pt-group metal (PGM)-based catalyst. The FeCoNi-CNF-coated glassy carbon electrode showed an oxygen reduction reaction/oxygen evolution reaction reversibility of 0.89 V in 0.1 M KOH solution. In RZAB, the maximum discharge power density (Pmax) of 120 mW cm-2 was obtained with FeCoNi-CNF, which is 86% of the Pmax measured with the PGM-based catalyst. Furthermore, during the RZAB charge-discharge cycling, the FeCoNi-CNF air electrode was found to be superior to the commercial PGM electrocatalyst in terms of operational durability and at least two times higher total life-time.

Bifunctional Oxygen Electrocatalysis on Mixed Metal Phthalocyanine-Modified Carbon Nanotubes Prepared via Pyrolysis.

Non-precious-metal catalysts are promising alternatives for Pt-based cathode materials in low-temperature fuel cells, which is of great environmental importance. Here, we have investigated the bifunctional electrocatalytic activity toward the oxygen reduction reaction (ORR) and the oxygen evolution reaction (OER) of mixed metal (FeNi; FeMn; FeCo) phthalocyanine-modified multiwalled carbon nanotubes (MWCNTs) prepared by a simple pyrolysis method. Among the bimetallic catalysts containing nitrogen derived from corresponding metal phthalocyanines, we report the excellent ORR activity of FeCoN-MWCNT and FeMnN-MWCNT catalysts with the ORR onset potential of 0.93 V and FeNiN-MWCNT catalyst for the OER having EOER = 1.58 V at 10 mA cm-2. The surface morphology, structure, and elemental composition of the prepared catalysts were examined with scanning electron microscopy, X-ray diffraction, and X-ray photoelectron spectroscopy. The FeCoN-MWCNT and FeMnN-MWCNT catalysts were prepared as cathodes and tested in anion-exchange membrane fuel cells (AEMFCs). Both catalysts displayed remarkable AEMFC performance with a peak power density as high as 692 mW cm-2 for FeCoN-MWCNT.

Transition-Metal- and Nitrogen-Doped Carbide-Derived Carbon/Carbon Nanotube Composites as Cathode Catalysts for Anion-Exchange Membrane Fuel Cells.

Transition-metal- and nitrogen-codoped carbide-derived carbon/carbon nanotube composites (M-N-CDC/CNT) have been prepared, characterized, and used as cathode catalysts in anion-exchange membrane fuel cells (AEMFCs). As transition metals, cobalt, iron, and a combination of both have been investigated. Metal and nitrogen are doped through a simple high-temperature pyrolysis technique with 1,10-phenanthroline as the N precursor. The physicochemical characterization shows the success of metal and nitrogen doping as well as very similar morphologies and textural properties of all three composite materials. The initial assessment of the oxygen reduction reaction (ORR) activity, employing the rotating ring-disk electrode method, indicates that the M-N-CDC/CNT catalysts exhibit a very good electrocatalytic performance in alkaline media. We find that the formation of HO2 - species in the ORR catalysts depends on the specific metal composition (Co, Fe, or CoFe). All three materials show excellent stability with a negligible decline in their performance after 10000 consecutive potential cycles. The very good performance of the M-N-CDC/CNT catalyst materials is attributed to the presence of M-N x and pyridinic-N moieties as well as both micro- and mesoporous structures. Finally, the catalysts exhibit excellent performance in in situ tests in H2/O2 AEMFCs, with the CoFe-N-CDC/CNT reaching a current density close to 500 mA cm-2 at 0.75 V and a peak power density (P max) exceeding 1 W cm-2. Additional tests show that P max reaches 0.8 W cm-2 in an H2/CO2-free air system and that the CoFe-N-CDC/CNT material exhibits good stability under both AEMFC operating conditions.

Transition metal-containing nitrogen-doped nanocarbon catalysts derived from 5-methylresorcinol for anion exchange membrane fuel cell application.

Highly active electrocatalysts for electrochemical oxygen reduction reaction (ORR) were prepared by high-temperature pyrolysis from 5-methylresorcinol, Co and/or Fe salts and dicyandiamide, which acts simultaneously as a precursor for reactive carbonitride template and a nitrogen source. The electrocatalytic activity of the catalysts for ORR in alkaline solution was studied using the rotating disc electrode (RDE) method. The bimetallic catalyst containing iron and cobalt (FeCoNC-at) showed excellent stability and remarkable ORR performance, comparable to that of commercial Pt/C (20 wt%). The superior activity was attributed to high surface metal and nitrogen contents. The FeCoNC-at catalyst was further tested in anion exchange membrane fuel cell (AEMFC) with poly-(hexamethyl-p-terphenylbenzimidazolium) (HMT-PMBI) membrane, where a high value of peak power density (Pmax = 415 mW cm-2) was achieved.

Preparation and characterization of hot-melt extruded polycaprolactone-based filaments intended for 3D-printing of tablets.

Hot-melt extruded (HME) filaments are an essential intermediate product for the three- dimensional (3D) printing of drug delivery systems (DDSs) by the fused deposition modelling (FDM) process. The aim of this study was to design novel polymeric 3D-printable HME filaments loaded with active pharmaceutical ingredients (APIs). The physical solid-state properties, mechanical properties, drug release and short-term storage stability of the filaments and 3D-printed DDSs were studied. Physical powder mixtures of polycaprolactone (PCL), plasticizer and API were manually blended, extruded by a single-screw extruder, and printed by a table-top FDM 3D-printing system. The composition of PCL and arabic gum (ARA) enabled the incorporation of 20%, 30% and 40% (w/w) of indomethacin (IND) and theophylline (THEO) into the HME filaments. The uneven distribution of API throughout the filaments impaired 3D printing. The HME filaments loaded with 20% IND or THEO were selected for the further analysis and printing tests (the ratio of PCL, ARA and IND or THEO was 7:1:2, respectively). The IND filaments were yellowish, mechanically strong and flexible, and they had a uniform filament diameter and smooth outer surface. The filaments containing THEO were smooth and off-white. The 3D-printed tablets fabricated from IND or THEO-loaded filaments showed sustained drug release in vitro. The drug release rate, however, significantly increased by changing the geometry of 3D-printed tablets from a conventional tablet structure to an unorthodox lattice ("honeycomb") structure. Overall, the combination of PCL and ARA provides an interesting novel polymeric carrier system for 3D-printable HME filaments and tablets.

Peat-derived hard carbon electrodes with superior capacity for sodium-ion batteries.

Herein we demonstrate how peat, abundant and cheap biomass, can be successfully used as a precursor to synthesize peat-derived hard carbons (PDCs), applicable as electrode materials for sodium-ion batteries (SIB). The PDCs were obtained by pre-pyrolysing peat at 300-800 °C, removing impurities with base-acid solution treatment and thereafter post-pyrolysing the materials at temperatures (T) from 1000 to 1500 °C. By modification of pre- and post-pyrolysis temperatures we obtained hard carbons with low surface areas, optimal carbonization degree and high electrochemical Na+ storage capacity in SIB half-cells. The best results were obtained when pre-pyrolysing peat at 450 °C, washing out the impurities with KOH and HCl solutions and then post-pyrolysing the obtained carbon-rich material at 1400 °C. All hard carbons were electrochemically characterized in half-cells (vs. Na/Na+) and capacities as high as 350 mA h g-1 at 1.5 V and 250 mA h g-1 in the plateau region (E < 0.2 V) were achieved at charging current density of 25 mA g-1 with an initial coulombic efficiency of 80%.

Interactions between Chloramphenicol, Carrier Polymers, and Bacteria-Implications for Designing Electrospun Drug Delivery Systems Countering Wound Infection.

Antibacterial drug-loaded electrospun nano- and microfibrous dressings are of major interest as novel topical drug delivery systems in wound care. In this study, chloramphenicol (CAM)-loaded polycaprolactone (PCL) and PCL/poly(ethylene oxide) (PEO) fiber mats were electrospun and characterized in terms of morphology, drug distribution, physicochemical properties, drug release, swelling, cytotoxicity, and antibacterial activity. Computational modeling together with physicochemical analysis helped to elucidate possible interactions between the drug and carrier polymers. Strong interactions between PCL and CAM together with hydrophobicity of the system resulted in much slower drug release compared to the hydrophilic ternary system of PCL/PEO/CAM. Cytotoxicity studies confirmed safety of the fiber mats to murine NIH 3T3 cells. Disc diffusion assay demonstrated that both fast and slow release fiber mats reached effective concentrations and had similar antibacterial activity. A biofilm formation assay revealed that both blank matrices are good substrates for the bacterial attachment and formation of biofilm. Importantly, prolonged release of CAM from drug-loaded fibers helps to avoid biofilm formation onto the dressing and hence avoids the treatment failure.

Suberin Fatty Acids from Outer Birch Bark: Isolation and Physical Material Characterization.

The isolation and physical material properties of suberin fatty acids (SFAs) were investigated with special reference to their potential applications as novel pharmaceutical excipients. SFAs were isolated from outer birch bark (OBB) with a new extractive hydrolysis method. The present simplified isolation process resulted in a moderate batch yield and chemical purity of SFAs, but further development is needed for establishing batch-to-batch variation. Cryogenic milling was the method of choice for the particle size reduction of SFAs powder. The cryogenically milled SFAs powder exhibited a semicrystalline structure with apparent microcrystalline domains within an amorphous fatty acids matrix. The thermogravimetric analysis (TGA) of SFAs samples showed a good thermal stability up to 200 °C, followed by a progressive weight loss, reaching a plateau at about 95% volatilization at about 470 °C. The binary blends of SFAs and microcrystalline cellulose (MCC; Avicel PH 101) in a ratio of 25:75 (w/w) displayed good powder flow and tablet compression properties. The corresponding theophylline-containing tablets showed sustained or prolonged-release characteristics. The physicochemical and bulk powder properties of SFAs isolated from OBB are auspicious in terms of potential pharmaceutical excipient applications.

Towards improved solubility of poorly water-soluble drugs: cryogenic co-grinding of piroxicam with carrier polymers.

Amorphous solid dispersions (SDs) open up exciting opportunities in formulating poorly water-soluble active pharmaceutical ingredients (APIs). In the present study, novel catalytic pretreated softwood cellulose (CPSC) and polyvinylpyrrolidone (PVP) were investigated as carrier polymers for preparing and stabilizing cryogenic co-ground SDs of poorly water-soluble piroxicam (PRX). CPSC was isolated from pine wood (Pinus sylvestris). Raman and Fourier transform infrared (FTIR) spectroscopy, X-ray powder diffraction (XRPD) and differential scanning calorimetry (DSC) were used for characterizing the solid-state changes and drug-polymer interactions. High-resolution scanning electron microscope (SEM) was used to analyze the particle size and surface morphology of starting materials and final cryogenic co-ground SDs. In addition, the molecular aspects of drug-polymer interactions and stabilization mechanisms are presented. The results showed that the carrier polymer influenced both the degree of amorphization of PRX and stabilization against crystallization. The cryogenic co-ground SDs prepared from PVP showed an enhanced dissolution rate of PRX, while the corresponding SDs prepared from CPSC exhibited a clear sustained release behavior. In conclusion, cryogenic co-grinding provides a versatile method for preparing amorphous SDs of poorly water-soluble APIs. The solid-state stability and dissolution behavior of such co-ground SDs are to a great extent dependent on the carrier polymer used.