Corrosion Study on Duplex Stainless Steel UNS S31803 Subjected to Solutions Containing Chloride Ions.

In the present work, the influence of a corrosive environment and temperature on the corrosion resistance properties of duplex stainless steel S31803 was evaluated. The corrosive process was carried out using solutions of 1.5% HCl (m/m) and 6% FeCl3 (m/m), at temperatures of 25 and 50 °C. The microstructure of UNS S31803 duplex stainless steel is composed of two phases, ferrite and austenite, oriented in the rolling direction, containing a ferrite percentage of 46.2% in the rolling direction and 56.1% in the normal direction. Samples, when subjected to corrosive media and temperature, tend to decrease their mechanical property values. It was observed, in both corrosive media, that with increasing test temperature, there is an increase in the corrosion rate, both uniform and pitting. The sample in HCl solution obtained a uniform corrosion rate of 0.85% at 25 °C and 0.92% at 50 °C and pitting rates of 0.77% and 1.47% at the same temperatures, respectively. When tested in FeCl3 solution, it obtained uniform corrosion of 0.0006% and 0.93% and pitting of 0.53% and 18.5%, at the same temperatures. A reduction in dissolution potentials is also noted, thus characterizing greater corrosion in the samples with increasing temperature.

Alkaline Activation of Binders: A Comparative Study.

Binders formulated with activated alkali materials to replace Portland cement, which has high polluting potential due to CO2 emissions in its manufacture, have increasingly been developed. The objective of this study is to evaluate the main properties of activated alkali materials (AAM) produced by blast furnace slag, fly ash, and metakaolin. Initially, binders were characterized by their chemical, mineralogical and granulometric composition. Later, specimens were produced, with molarity variation between 4.00 and 5.50, using the binders involved in the research. In preparing the activating solution, sodium hydroxide and silicate were used. The evaluated properties of AAM were consistency, viscosity, water absorption, density, compressive strength (7 days of cure), calorimetry, mineralogical analysis by X-ray diffraction, and morphological analysis by scanning electron microscopy. The results of evaluation in the fresh state demonstrate that metakaolin has the lowest workability indices of the studied AAM. The results observed in the hardened state indicate that the metakaolin activation process is optimized with normal cure and molarity of 4.0 and 4.5 mol/L, obtaining compressive strength results after 7 days of curing of approximately 30 MPa. The fly ash activation process is the least intense among the evaluated binders. This can be seen from the absence of phases formed in the XRD in the compositions containing fly ash as binder. Unlike blast furnace slag and metakaolin, the formation of sodalite, faujasite or tobermorite is not observed. Finally, the blast furnace slag displays more intense reactivity during thermal curing, obtaining compressive strength results after 7 days of curing of around 25 MPa. This is because the material's reaction kinetics are low but can be increased in an alkaline environment, and by the effect of temperature. From these results, it is concluded that each precursor has its own activation mechanism, observed by the techniques used in this research. From the results obtained in this study, it is expected that the alkaline activation process of the types of binders evaluated herein will become a viable alternative for replacing Portland cement, thus contributing to cement technology and other cementitious materials.

Influence of drying temperature on coconut-fibers.

The use of natural fibers in cementitious composites has been gaining prominence in engineering. The natural lignocellulosic fibers (NLFs) used in these composites have advantages such as reduced density, reduced fragmentation and concrete cracking, thus improving flexural performance and durability. Coconut-fiber is one of those natural fibers and its use presents technical, ecological, social and economic benefits, as it is improperly disposed of, representing a large waste of natural resources, in addition to causing environmental pollution.. Thus, composites reinforced with natural fibers are promising materials for the construction industry, as in addition to meeting the sustainability of buildings, there will also be a reduction in urban solid waste generated and gains for structures with the use of environmentally friendly materials that meet to active efforts and with greater durability. This work aims to evaluate the tensile behavior of green coconut-fibers subjected to different drying temperatures through chemical, thermal (TG/DSC), morphological, visual and mechanical analysis. Drying temperatures of 70 °C, 100 °C and 130 °C were analyzed and the results indicated that the drying temperature at 70 °C was satisfactory, providing fiber-reinforced composites with good tensile strength, combined with good ductility.

An alternative hybrid lipid nanosystem combining cytotoxic and magnetic properties as a tool to potentiate antitumor effect of 5-fluorouracil.

AIMS: Colorectal cancer is the third most frequent type of cancer and the second leading cause of cancer-related deaths worldwide. The majority of cases are diagnosed at a later stage, leading to the need for more aggressive treatments such as chemotherapy. 5-Fluorouracil (5-FU), known for its high cytotoxic properties has emerged as a chemotherapeutic agent. However, it presents several drawbacks such as lack of specificity and short half-life. To reduce these drawbacks, several strategies have been designed namely chemical modification or association to drug delivery systems. MATERIALS AND METHODS: Current research was focused on the design, physicochemical characterization and in vitro evaluation of a lipid-based system loaded with 5-FU. Furthermore, aiming to maximize preferential targeting and release at tumour sites, a hybrid lipid-based system, combining both therapeutic and magnetic properties was developed and validated. For this purpose, liposomes co-loaded with 5-FU and iron oxide (II, III) nanoparticles were accomplished. KEY FINDINGS: The characterization of the developed nanoformulation was performed in terms of incorporation parameters, mean size and surface charge. In vitro studies assessed in a murine colon cancer cell line confirmed that 5-FU antiproliferative activity was preserved after incorporation in liposomes. In same model, iron oxide (II, III) nanoparticles did not exhibit cytotoxic properties. Additionally, the presence of these nanoparticles was shown to confer magnetic properties to the liposomes, allowing them to respond to external magnetic fields. SIGNIFICANCE: Overall, a lipid nanosystem loading a chemotherapeutic agent displaying magnetic characteristics was successfully designed and physicochemically characterized, for further in vivo applications.

Influence of Pulsed Arc Parameters on the Tig Welding Process for the Stainless Steel Duplex UNS S31803.

The influence of parameters involved in the pulsed electric arc, used as an energy source in the tungsten inert gas (TIG)-mediated welding of Duplex UNS S31803 stainless steel, to attend the manufacture of flexible pipes for the extraction of oil and gas is presented. A fundamental part in the manufacturing process of flexible pipelines is the welding of these strips so that corresponding TIG welds will be subjected to the same process and work conditions. Therefore, it is necessary to maintain the same properties in the welded regions. Covering the effects of each parameter of the pulsed electric arc such as peak and base current as welds, cyclic ratio, and pulsation frequency is a desirable endeavor. The final objective is the mitigation of problems that have a great impact on production, such as weld breakage during the conformation of the strip in the process and test failures. With this, tensile, bending, and ferrite percentage tests were performed on 12 samples that qualified as satisfactory in the visual aspect. A minimum tensile strength of 734.57 MPa and a maximum of 775.77 MPa were obtained where all values found are above the tensile strength limit of the base material of 620 MPa. With the completion of the study, it is possible to understand not only the response of the process to each parameter but also the tendency when changing them. Moreover, it is possible to explore the possibility of guiding the changes to achieve results about the visual aspect and the mechanical properties of the welded material.

Characterization of Artificial Stone Produced with Blast Furnace Dust Waste Incorporated into a Mixture of Epoxy Resin and Cashew Nut Shell Oil.

The demand for materials with improved properties and less negative impact on the environment is growing. Artificial stones are examples of these materials produced with up to 90% of particulate material joined by a binder. This article evaluates the physical and mechanical properties of two artificial stones produced with processing steel residue (blast furnace dust waste) and quartz powder. Two binders were used: pure epoxy resin, denoted as ASPB100, or a mixture of 70 wt% epoxy resin with 30 wt% cashew nut shell oil, denoted as ASPB7030. The process took place under vibration, compression (3 MPa/20 min and 90 °C) and vacuum (80 Pa). ASPB100 showed water absorption of 0.07%, while for ASPB7030, it was 0.54%. They were classified as having high mechanical strength associated with bending stress values equal to 32 and 25 MPa, respectively. Stain resistance indicated that both artificial stones had their stains removed with the tested cleaning agents. In this way, the novel artificial stones produced are sustainable alternatives for the application of blast furnace waste and cashew nut shell oil, reducing their negative impacts on the environment.

Characterization and photocatalytic performance of cement mortars with incorporation of TiO2 and mineral admixtures.

As the main components of the building envelope, construction materials have a straight relation with air contaminants from anthropogenic origins. Titanium dioxide has been recently applied in construction industry products since its photocatalytic properties can be used for pollutant degradation purposes. This study evaluated the performance of cement-based mortars with the incorporation of TiO2 nanoparticles and mineral admixtures. Six mortar compositions were defined by considering two reference mixes (with and without TiO2 incorporation), two mineral admixtures (bentonite and metakaolin) as partial cement replacement and one waste from ornamental stone processing in two levels of partial substitution of natural sand. Consistency index, density, and entrained air content of mixtures were investigated at fresh state. Compressive strength, water absorption, sorptivity, and micrographs from scanning electron microscopy were used to characterize mortars at hardened state. It was observed that incorporation of TiO2 does not considerably change mortar's properties at fresh and hardened state, despite a denser microstructure and improved interfacial transition zone. In general, the relation between the water-to-cement ratio and porosity on the performances of TiO2-added mortars was shown, which is strongly related to their photocatalytic efficiency. Metakaolin mixtures were more efficient to NO conversion, and high selectivity was observed for the bentonite mortars.

Methods for Evaluating Pozzolanic Reactivity in Calcined Clays: A Review.

The search for alternative materials to replace ordinary Portland cement has been the object of work that enhances the investigation of the use of pozzolanic materials and the reduction of the carbon footprint with supplementary cementitious materials. However, not all materials are available to meet the large-scale demand for cement replacement. A relevant exception is the calcined clay, a material found worldwide that, when subjected to appropriate heat treatment, presents pozzolanic reactivity and can be used as a supplementary material to cement. This review presents, through a systematic search, methods for measuring the pozzolanic reactivity of calcined clays, namely, direct, indirect, qualitative, quantitative, chemical and physical methods such as electrical conductivity (Lùxan), the force activity index, the modified Chapelle, R3, Frattini test, thermal analysis, X-ray diffraction and X-ray fluorescence spectrometry. The most usual methods to assess the pozzolanic reactivity of calcined clays were exposed and analyzed. It should be pointed out that there is greater use of the Frattini and modified Chapelle methods as well as the analysis of the mechanical strength behavior of the material in cementitious matrices. X-ray diffraction and thermal analysis were exposed as the most used correlation methods but it was also concluded that different tests are needed to generate accurate results.

Comparison of the Permeability of Potential Ballast Rocks from Northern Rio de Janeiro State under Different Fouling Rates after Sodium Sulfate Attack.

This paper aimed to analyze the reduction in the ballast layer permeability simulated in a laboratory in saturated conditions by the presence of rock dust as a contaminant of three types of rocks explored in different deposits in the northern region of the state of Rio de Janeiro, Brazil, through laboratory testing relating the physical properties of rock particles before and after sodium sulfate attack. Sodium sulfate attack is justified by the proximity of some sections of the planned EF-118 Vitória-Rio railway line to the coast and of the sulfated water table to the ballast bed, which could degrade the material used and compromise the railway track. Granulometry and permeability tests were performed to compare ballast samples with fouling rates of 0, 10, 20, and 40% rock dust by volume. A constant head permeameter was used to analyze hydraulic conductivity and establish correlations between the petrography and mercury intrusion porosimetry of the rocks, namely two types of metagranite (Mg1 and Mg3) and a gneisse (Gn2). Rocks, such as Mg1 and Mg3, with a larger composition of minerals susceptible to weathering according to petrography analyses, tend to be more sensitive to weathering tests. This, in conjunction with the climate in the region studied, with average annual temperature and rainfall of 27 °C and 1200 mm, could compromise track safety and user comfort. Additionally, the Mg1 and Mg3 samples showed greater percentage variation in wear after the Micro-Deval test, which could damage the ballast due to the considerable changeability of the material. The mass loss caused by abrasion due to the passage of rail vehicles was assessed by the Micro-Deval test, with Mg3 (intact rock) declining from 8.50 ± 1.5 to 11.04 ± 0.5% after chemical attack. However, Gn2, which exhibited the greatest mass loss among the samples, showed no significant variation in average wear, and its mineralogical characteristics remained almost unchanged after 60 sodium sulfate cycles. These aspects, combined with its satisfactory hydraulic conductivity rate, indicate that Gn2 is suitable for use as railway ballast in the EF-118 railway line.

A Review of the Use of Coconut Fiber in Cement Composites.

The use of plant fibers in cementitious composites has been gaining prominence with the need for more sustainable construction materials. It occurs due to the advantages natural fibers provide to these composites, such as the reduction of density, fragmentation, and propagation of cracks in concrete. The consumption of coconut, a fruit grown in tropical countries, generates shells that are improperly disposed of in the environment. The objective of this paper is to provide a comprehensive review of the use of coconut fibers and coconut fiber textile mesh in cement-based materials. For this purpose, discussions were conducted on plant fibers, the production and characteristics of coconut fibers, cementitious composites reinforced with coconut fibers, cementitious composites reinforced with textile mesh as an innovative material to absorb coconut fibers, and treatments of coconut fiber for improved product performance and durability. Finally, future perspectives on this field of study have also been highlighted. Thus, this paper aims to understand the behavior of cementitious matrices reinforced with plant fibers and demonstrate that coconut fiber has a high capacity to be used in cementitious composites instead of synthetic fibers.

Evaluation of Light Cementitious Matrix with Composite Textile Reinforcement from Garment Waste.

The use of recycled waste has been the focus of several studies due to its potential to allow a more sustainable use of construction materials and minimize improper waste disposal in landfills or incinerators. More specifically, garment textile waste has been examined as internal reinforcement of cementitious matrices to increase the deformability and control fissure formation. In this study, polyester textiles are analyzed and incorporated in cementitious composites in order to evaluate their mechanical properties. Results show that significant improvements in mechanical properties of composites are obtained depending on the impregnation treatment applied to the textile waste. In the direct tensile stress test, the waste impregnation with styrene butadiene polymer plus silica fume improved 35.95% in the weft direction and 9.33% in the warp direction. Maximum stress increased 53.57% and 64.48% for composites with styrene-butadiene rubber impregnation and styrene-butadiene rubber plus silica fume impregnation, respectively, when compared to the unreinforced composite. The flexural tensile strength of composites impregnated reinforcements with styrene-butadiene rubber and styrene-butadiene rubber plus silica fume presented increases in strength by 92.10% and 94.73%, respectively, when compared to the unreinforced sample. The impact test confirmed that styrene-butadiene rubber plus silica fume impregnation produced greater tenacity of the composite. In the microstructure, it is confirmed that the impregnated textile reinforcement resulted in composites with greater adhesion between the fabric and the cementitious matrix. Thus, light textile waste is concluded to be a viable construction material for non-structural elements.

Effects of Particle Size Distribution of Standard Sands on the Physical-Mechanical Properties of Mortars.

Obtained natural sands can present different particle size distributions (PSD), although they have the same mineralogical origin. These differences directly influence the physical and mechanical behavior of mortars and, therefore, the performance of mortar and ceramic renderings. Standardizing the particle size of sands based on pre-established requirements in normative standards (NBR 7214 or ASTM C778) is one way to minimize these effects. However, these standards do not consider the optimization of the granular skeleton through the analysis of bulk density and PSD, which may be insufficient to obtain satisfactory results. Therefore, this paper analyzes the effects of using different particle size ranges on the physical and mechanical behavior of cement and hydrated lime mortars. The properties of consistency index, bulk density, air content, capillary water absorption, water absorption by immersion, flexural strength, compressive strength, and dynamic modulus of elasticity were evaluated. For this purpose, standardized sands of the same mineralogical origin were made with different particle size ranges, being: (i) standardized sand constituted by 25% of coarse and fine fractions (S25-control), (ii) standardized sand constituted by 30% of coarse fraction and 20% of fine fraction (S30-20), and (iii) standardized sand composed by 40% of coarse fraction, and 10% of fine fraction (S40-10), respectively. The results indicated that variations in the particle size composition of the standardized sands are necessary to obtain mixtures with higher compactness and, therefore, mortars with better physical and mechanical performance. Thus, the dosage of the particle size fractions of standardized sand should consider the optimization of the granular skeleton, being the unit mass and the granulometric composition as important parameters to meet this premise.

Demolition Waste Potential for Completely Cement-Free Binders.

Due to renovation and fighting in the world, a huge accumulation of construction and demolition waste is formed. These materials are effectively used as aggregates, but there is very little information about the use of scrap concrete to create cementless binders. The purpose of the work is to be a comprehensive study of the composition and properties of concrete wastes of various fractions with the aim of their rational use as cementless binders. The scientific novelty lies in the fact that the nature of the processes of structure formation of a cementless binder based on sandy fractions of the screening of fragments of destroyed buildings and structures, as a complex polyfunctional system, has been theoretically substantiated and experimentally confirmed. Different percentages of non-hydrated clinker minerals in concrete scrap were determined. In the smallest fraction (less than 0.16 mm), more than 20% of alite and belite are present. Waste of the old cement paste is more susceptible to crushing compared to the large aggregate embedded in it, therefore, particles of the old cement paste and fine aggregate predominate in the finer fractions of the waste. Comprehensive microstructural studies have been carried out on the possibility of using concrete scrap as a completely cementless binder using scanning electron microscopy, X-ray diffraction analysis, and differential thermal analysis. It has been established that for cementless samples prepared from the smallest fractions (less than 0.315 mm), the compressive strength is 1.5-2 times higher than for samples from larger fractions. This is due to the increased content of clinker minerals in their composition. The compressive strength of the cementless binder after 28 days (7.8 MPa), as well as the early compressive strength at the age of 1 day after steaming (5.9 MPa), make it possible to effectively use these materials for enclosing building structures.

Evaluation of CNTs and SiC Whiskers Effect on the Rheology and Mechanical Performance of Metakaolin-Based Geopolymers.

Despite geopolymers having emerged as a more sustainable alternative to Portland cement, their rheological properties still need to be thoroughly investigated, aiming at the material's applicability. Additionally, studies that evaluated the fresh state of geopolymer composites with nanomaterials are scarce. Thus, two metakaolin-based geopolymer systems were reinforced with nanomaterials with a similar geometry: carbon nanotubes (CNT) and silicon carbide whiskers (SCW). The nanomaterials incorporation was assessed by rotational rheometry (conducted up to 110 min), isothermal calorimetry, compressive strength after 7 and 28 days, and the microstructure was investigated using X-ray diffraction (XRD) and Fourier-transform infrared spectroscopy (FTIR). CNT and SCW incorporation (0.20 wt.%) did not significantly affect the yield stress and viscosity of the R2-group (based on metakaolin type 2), while increasing the rheological parameters up to 56.0% for the R1-group (based on metakaolin type 1). Both additions modified the reaction kinetics. Increments of up to 40.7% were observed in the compressive strength of geopolymer pastes with the incorporation of a SCW content of 0.2 wt.%. XRD and FTIR results suggest similar structural modifications between precursors. Nevertheless, R2 showed substantial transformations while the R1 group exhibited anhydrous material that can react over time. Overall, incorporating CNT and SCW contributed to higher mechanical increments on systems with average mechanical strength (R1) compared to systems with higher potential mechanical performance (R2).

Recycled Aggregate: A Viable Solution for Sustainable Concrete Production.

Construction and demolition activities consume large amounts of natural resources, generating 4.5 bi tons of solid waste/year, called construction and demolition waste (C&DW) and other wastes, such as ceramic, polyethylene terephthalate (PET), glass, and slag. Furthermore, around 32 bi tons of natural aggregate (NA) are extracted annually. In this scenario, replacing NA with recycled aggregate (RA) from C&DW and other wastes can mitigate environmental problems. We review the use of RA for concrete production and draw the main challenges and outlook. RA reduces concrete's fresh and hardened performance compared to NA, but these reductions are often negligible when the replacement levels are kept up to 30%. Furthermore, we point out efficient strategies to mitigate these performance reductions. Efforts must be spent on improving the efficiency of RA processing and the international standardization of RA.

Mechanical Feasibility Study of Pressed and Burned Red Ceramic Blocks as Structural and Sealing Masonry.

In the search for better constructive efficiency and a reduction of the waste of construction materials, several researches have been performed in the last years around the world. Red ceramic blocks are artifacts widely used in civil construction around the world, and they result in a great consumption of raw materials and energy. The great innovation of this research was the development of ceramic blocks through an innovative method of pressing and dosing materials, replacing the traditional stage of extrusion in the manufacture of ceramics. In such a sense, a new manufacturing technology for ceramic blocks was proposed through the pressing process, adapting the soil-cement brick press machine, thus attaining more even pieces with greater compliance to the dimensions and preset geometry. In this work, the physical and mechanical features of the pressed and burned blocks (PBB) are produced in a partnership with Arte Cerâmica Sardinha, a traditional ceramic industry in the region of Campos dos Goytacazes, RJ, Brazil. It was sought to set the quality parameters for the blocks, to set their mechanical compressive strength, deformation modules and the Poisson coefficient. The blocks were tested in use by means of three layers of prism and small wall samples, and it was checked the fragile-type failure of the PBB. Results indicate that the blocks can be employed in small-sized construction works, as the characteristic compressive strength to block measured was 3.62 N/mm2 for average water absorption of 20.84%.

Technogenic Fiber Wastes for Optimizing Concrete.

A promising method of obtaining mineral fiber fillers for dry building mixtures is the processing of waste that comes from the production of technogenic fibrous materials (TFM). The novelty of the work lies in the fact that, for the first time, basalt production wastes were studied not only as reinforcing components, but also as binder ones involved in concrete structure formation. The purpose of the article is to study the physical and mechanical properties of waste technogenic fibrous materials as additives for optimizing the composition of raw concrete mixes. To assess the possibility of using wastes from the complex processing of TFM that were ground for 5 and 10 min as an active mineral additive to concrete, their chemical, mineralogical, and granulometric compositions, as well as the microstructure and physical and mechanical characteristics of the created concretes, were studied. It is established that the grinding of TFM for 10 min leads to the grinding of not only fibers, but also pellets, the fragments of which are noticeable in the total mass of the substance. The presence of quartz in the amorphous phase of TFM makes it possible to synthesize low-basic calcium silicate hydrates in a targeted manner. At 90 days age, at 10-20% of the content of TFM, the strength indicators increase (above 40 MPa), and at 30% of the additive content, they approach the values of the control composition without additives (above 35 MPa). For all ages, the ratio of flexural and compressive strengths is at the level of 0.2, which characterizes a high reinforcing effect. Analysis of the results suggests the possibility of using waste milled for 10 min as an active mineral additive, as well as to give better formability to the mixture and its micro-reinforcement to obtain fiber-reinforced concrete.

Effect of Polymers on Behavior of Ultra-High-Strength Concrete.

The development of ultra-high-performance concrete (UHPC) is still practically limited due to the scarcity of robust mixture designs and sustainable sources of local constituent materials. This study investigates the engineering characteristics of Styrene Butadiene Rubber (SBR) polymeric fiber-reinforced UHPC with partial substitution of cement at 0, 5 and 20 wt.% with latex polymer under steam and air curing techniques. The compressive and tensile strengths along with capillary water absorption and sulfate resistance were measured to evaluate the mechanical and durability properties. Scanning Electron Microscopy (SEM) was carried out to explore the microstructure development and hydration products in the designed mixtures under different curing regimes. The results indicated that the mixtures incorporating 20 wt.% SBR polymer achieved superior compressive strength at later ages. Additionally, the tensile strength of the polymeric UHPC without steel fibers and with 20% polymers was enhanced by 50%, which promotes the development of novel UHPC mixtures in which steel fibers could be partially replaced by polymer, while enhancing the tensile properties.

Mechanical and Physical Properties of Particleboard Made from the Sumatran Elephant (Elephas maximus sumatranus) Dung and Wood Shaving.

Sumatran elephants (Elephas maximus sumatranus) are the world's largest living land mammals. The elephant's digestive system can only absorb 40% of the nutrients in digested feed, and the remainder is excreted as dung. Elephant dung waste can be used as a particleboard material due to its high fiber content. The objectives of this study are: (i) to prepare elephant dung waste as raw material for particleboard, (ii) to improve elephant dung particleboard's physical and mechanical properties using wood shavings, and (iii) to study the influence of several parameters on the physical and mechanical properties of particleboard. The particleboard dimensions and density were set at 20 cm × 20 cm × 1 cm and 0.8 g/cm3, respectively. The mixture ratio of elephant dung and wood shavings was 100/0, 90/10, 80/20, 70/30, 60/40, and 50/50 (% w/w). This mixture ratio of particles was sprayed with 7% isocyanate adhesive. The pressing at a pressure of 30 kg/cm2 for 5 min and 160 °C was used in this study. The physical and mechanical properties of particleboard were tested according to JIS A 5908 (2003) standard. The result shows that the addition of wood shaving improved the elephant dung particleboard's physical and mechanical properties. Except for moisture content and water absorption, the addition of wood shavings has a significant effect on elephant dung particleboard's physical and mechanical properties. The best ratio of elephant dung and wood-shaving for this research is 50/50 and has fulfilled the JIS A 5908-2003 standard, except for thickness swelling.

Eco-friendly ceramic bricks: a comparative study of life cycle impact methods.

The growing need for natural resources for the production of inputs for construction, such as ceramic bricks, as well as the high rates of solid waste generation in the sector, makes construction an industrial segment with unfavorable environmental effects. The Life Cycle Assessment (LCA) emerges as a tool capable of assisting in the quantification and analysis of the impacts associated with construction materials, whether traditional or alternative. Thus, the goal of this paper is to assess the environmental impacts associated with the development of alternative building materials. To compare the conventional and the alternative bricks, both were evaluated according to the LCIA methods Ecoindicator 99, IMPACT 2002+, and ReCiPe 2016, in the midpoint and endpoint levels. The sensitivity analysis was carried out considering as an alternative input for the firing process, a mixture composed of wood and biomass originating from the Pennisetum purpureum. According to Ecoindicator 99 method, the categories respiratory organics, fossil fuels, and radiation stand out, which showed greater sensitivity in altering the input used in the firing process, reducing their impacts by 38.38%, 34.68%, and 31.81%, respectively, when comparing product III (ceramic brick incorporated with OSPW and submitted to the firing process with the mix of wood and Pennisetum purpureum) and product I (ceramic brick incorporated with OSPW and submitted to the traditional firing process). In addition, in the respiratory organics category, the IMPACT 2002+ method showed a reduction of approximately 43% of the impacts associated with product III, when compared to the product with the greatest impact in this category. In a global analysis of the results presented by the ReCiPe 2016 method, the product III had the lowest associated environmental impact when compared to the other evaluated systems.