Electrochemical and Structural Study of a Chemically Dealloyed PtCu Oxygen Reduction Catalyst.

A carbon-supported, dealloyed platinum-copper (Pt-Cu) oxygen reduction catalyst was prepared using a multi-step synthetic procedure. Material produced at each step was characterized using high angle annular dark field scanning transmission electron microscopy (HAADF-STEM), electron energy loss spectroscopy (EELS) mapping, x-ray absorption spectroscopy (XAS), x-ray diffraction (XRD), and cyclic voltammetry (CV), and its oxygen reduction reaction (ORR) activity was measured by a thin-film rotating disk electrode (TF-RDE) technique. The initial synthetic step, a co-reduction of metal salts, produced a range of poorly crystalline Pt, Cu, and Pt-Cu alloy nanoparticles that nevertheless exhibited good ORR activity. Annealing this material alloyed the metals and increased particle size and crystallinity. TEM shows the annealed catalyst to include particles of various sizes, large (>25 nm), medium (12-25 nm), and small (<12 nm). Most of the small and medium-sized particles exhibited a partial or complete coreshell (Cu-rich core and Pt shell) structure with the smaller particles typically having more complete shells. The appearance of Pt shells after annealing indicates that they are formed by a thermal diffusion mechanism. Although the specific activity of the catalyst material was more than doubled by annealing, the concomitant decrease in Pt surface area resulted in a drop in its mass activity. Subsequent dealloying of the catalyst by acid treatment to partially remove the copper increased the Pt surface area by changing the morphology of the large and some medium particles to a "Swiss cheese" type structure having many voids. The smaller particles retained their core-shell structure. The specific activity of the catalyst material was little reduced by dealloying, but its mass activity was more than doubled due to the increase in surface area. The possible origins of these results are discussed in this report.

Ultra performance liquid chromatography-atmospheric pressure photoionization-tandem mass spectrometry for high-sensitivity and high-throughput analysis of U.S. Environmental Protection Agency 16 priority pollutants polynuclear aromatic hydrocarbons.

In this work, we demonstrate the utility of ultra performance liquid chromatography-atmospheric pressure photoionization-tandem mass spectrometry (UPLC-APPI-MS/MS) for high-sensitivity and high-throughput analysis of United States Environmental Protection Agency (U.S. EPA) 16 priority pollutants polycyclic aromatic hydrocarbons (PAHs). Analyses were performed on a Waters Acquity-TQD equipped with Syagen's PhotoMate APPI source. All 16 PAHs were analyzed on column in approximately 3.5 min with excellent chromatographic separation for all PAH isomers and with low picogram detection limits on column for all analytes using chlorobenzene as a dopant. Dynamic linear ranges were evaluated and found to cover at least 3-4 orders of magnitude. In comparison with the existing U.S. EPA methods, this approach improves instrument sample throughput by at least 10-fold.

Sonochemical method for producing titanium metal powder.

We demonstrate a sonochemical method for producing titanium metal powder. The method uses low intensity ultrasound in a hydrocarbon solvent at near-ambient temperatures to first create a colloidal suspension of liquid sodium-potassium alloy in the solvent and then to reduce liquid titanium tetrachloride to titanium metal under cavitation conditions. XRD data collected for the reaction products after the solvent removal show only NaCl and KCl, with no diffraction peaks attributable to titanium metal or other titanium compounds, indicating either the formation of amorphous metal or extremely small crystallite size. TEM micrographs show that hollow spheres formed of halide salts and titanium metal, with diameters with diameters ranging from 100 to 500 nm and a shell thickness of 20 to 40 nm form during the synthesis, suggesting that the sonochemical reaction occurs inside the liquid shell surrounding the cavitation bubbles. Metal particle sizes are estimated to be significantly smaller than 40 nm from TEM data. XRD data of the powder after annealing and prior to removal of the alkali chloride salts provides direct evidence that titanium metal was formed during the sonochemical synthesis.

Improved hydrogen release from LiB0.33N0.67H2.67 with noble metal additions.

The hydrogen release behavior of the quaternary hydride LiB(0.33)N(0.67)H(2.67) has been successfully improved through the incorporation of small quantities of noble metal. Adding 5 wt % Pd either as Pd metal particles or as PdCl(2) reduced the temperature T(1/2) corresponding to the midpoint of the hydrogen release reaction by DeltaT(1/2) = -43 degrees C and -76 degrees C, respectively. PtCl(2) and Pt nanoparticles supported on a Vulcan carbon substrate proved to be even more effective, with DeltaT(1/2) = -90 degrees C. The amount of NH(3) released during dehydrogenation is reduced compared to that from additive-free material, and, more importantly, at temperatures below 210 degrees C hydrogen is released with no detectable NH(3). In contrast to additive-free LiB(0.33)N(0.67)H(2.67), which melts completely above 190 degrees C and releases hydrogen from the liquid state only above approximately 250 degrees C, hydrogen release from LiB(0.33)N(0.67)H(2.67) + 5 wt % Pt/Vulcan carbon is accompanied by partial melting plus a cascade through a series of solid intermediate phases. Calorimetric measurements indicate that both additive-free and Pt-added LiB(0.33)N(0.67)H(2.67) release hydrogen exothermically, and hence the reverse reaction is thermodynamically unfavorable. By exposing partially dehydrogenated samples to high H(2) pressures at modest temperatures, fractional hydrogen uptake (roughly 15% of the released hydrogen) has been achieved. The mechanism by which noble metals promote hydrogen release is not known, but the behavior is consistent with that expected for a catalyst, including a large effect with small additions and saturation of the effect at low concentration.

Hydrogen release from mixtures of lithium borohydride and lithium amide: a phase diagram study.

We recently reported the synthesis of a new quaternary hydride in the lithium-boron-nitrogen-hydrogen quaternary phase diagram with the approximate composition LiB0.33N0.67H2.67 having a theoretical hydrogen content of 11.9 wt %. This new compound forms by the reaction of appropriate amounts of lithium amide (LiNH2) and lithium borohydride (LiBH4) and releases greater than 10 wt % hydrogen when heated. A small amount of ammonia, 2-3 mol % of the generated gas, is also released. We now report a study of hydrogen and ammonia release from the series of reactant mixtures (LiNH2)x(LiBH4)1-x, where x=0.667 corresponds to the composition LiB0.33N0.67H2.67. We measured hydrogen and ammonia release amounts as a function of composition and found that maximum hydrogen and minimum ammonia release do occur for x=0.667. We also present evidence for an additional new quaternary phase and for two possibly metastable phases in this system.

On the composition and crystal structure of the new quaternary hydride phase Li4BN3H10.

X-ray data on single crystals of the quaternary metal hydride near the composition LiB(0.33)N(0.67)H(2.67), previously identified as "Li3BN2H8", reveal that its true composition is Li4BN3H10. The structure has body-centered-cubic symmetry [space group I2(1)3, cell parameter a = 10.679(1)-10.672(1) Angstroms] and contains an ordered arrangement of BH4- and NH2- anions in the molar ratio 1:3. The borohydride anion has an almost ideal tetrahedral geometry (angleH-B-H approximately 108-114 degrees), while the amide anion has a nearly tetrahedral bond angle (angleH-N-H approximately 106 degrees). Three symmetry-independent Li atom sites are surrounded by BH4- and NH2- anions in various distorted tetrahedral configurations, one by two B and two N atoms, another by four N atoms, and the third by one B and three N atoms. The Li configuration around B is nearly tetrahedral, while that around N resembles a distorted saddlelike configuration, similar to those in LiBH4 and LiNH2, respectively.

Hydrogen desorption exceeding ten weight percent from the new quaternary hydride Li3BN2H8.

Mobile applications of hydrogen power have long demanded new solid hydride materials with large hydrogen storage capacities. We report synthesis of a new quaternary hydride having the approximate composition Li(3)BN(2)H(8) with 11.9 wt % theoretical hydrogen capacity. It forms by reacting LiNH(2) and LiBH(4) powders in a 2:1 molar ratio either by ball milling or by heating the mixed powders above 95 degrees C. This new quaternary hydride melts at approximately 190 degrees C and releases > or =10 wt % hydrogen above approximately 250 degrees C. A small amount of ammonia (2-3 mol % of the generated gas) is released simultaneously. Preliminary calorimetric measurements suggest that hydrogen release is exothermic and, hence, not easily reversible.

Combined electrospray ionization-atmospheric pressure chemical ionization source for use in high-throughput LC-MS applications.

Fast and accurate analytical methods are essential to keep pace with sample libraries produced from combinational chemistry and high-throughput biological screening. Many laboratories now use a combination of ionization techniques for the characterization of these samples, including atmospheric pressure chemical ionization (APCI), electrospray ionization (ESI), and photoionization (PI). Data are shown here from the analysis of a compound collection plate containing a variety of sample structures. ESI will normally analyze around 80% of these samples, necessitating a source change to analyze a further 10%. In this work, we have developed a new combined ESI-APCI source (ESCi) for use in on-line HPLC applications. The combined source allows alternate on-line ESI and APCI scans with polarity switching within a single analysis. The ESCi source has been designed to be a simple replacement for the existing mass spectrometer interfaces. Each ionization method is optimized independently using separate tuning parameters. Instrument electronics can readily switch between the two ionization methods and polarities within normal interscan time periods. The new source has reduced the analysis time of sample plates by eliminating the need for a source hardware change, source optimization, and repeat analyses.