Fraxicon for Optical Applications with Aperture ∼1 mm: Characterisation Study.

Emerging applications of optical technologies are driving the development of miniaturised light sources, which in turn require the fabrication of matching micro-optical elements with sub-1 mm cross-sections and high optical quality. This is particularly challenging for spatially constrained biomedical applications where reduced dimensionality is required, such as endoscopy, optogenetics, or optical implants. Planarisation of a lens by the Fresnel lens approach was adapted for a conical lens (axicon) and was made by direct femtosecond 780 nm/100 fs laser writing in the SZ2080™ polymer with a photo-initiator. Optical characterisation of the positive and negative fraxicons is presented. Numerical modelling of fraxicon optical performance under illumination by incoherent and spatially extended light sources is compared with the ideal case of plane-wave illumination. Considering the potential for rapid replication in soft polymers and resists, this approach holds great promise for the most demanding technological applications.

Combined Femtosecond Laser Glass Microprocessing for Liver-on-Chip Device Fabrication.

Nowadays, lab-on-chip (LOC) devices are attracting more and more attention since they show vast prospects for various biomedical applications. Usually, an LOC is a small device that serves a single laboratory function. LOCs show massive potential for organ-on-chip (OOC) device manufacturing since they could allow for research on the avoidance of various diseases or the avoidance of drug testing on animals or humans. However, this technology is still under development. The dominant technique for the fabrication of such devices is molding, which is very attractive and efficient for mass production, but has many drawbacks for prototyping. This article suggests a femtosecond laser microprocessing technique for the prototyping of an OOC-type device-a liver-on-chip. We demonstrate the production of liver-on-chip devices out of glass by using femtosecond laser-based selective laser etching (SLE) and laser welding techniques. The fabricated device was tested with HepG2(GS) liver cancer cells. During the test, HepG2(GS) cells proliferated in the chip, thus showing the potential of the suggested technique for further OOC development.

Femtosecond Laser Assisted 3D Etching Using Inorganic-Organic Etchant.

Selective laser etching (SLE) is a technique that allows the fabrication of arbitrarily shaped glass micro-objects. In this work, we show how the capabilities of this technology can be improved in terms of selectivity and etch rate by applying an etchant solution based on a Potassium Hydroxide, water, and isopropanol mixture. By varying the concentrations of these constituents, the wetting properties, as well as the chemical reaction of fused silica etching, can be changed, allowing us to achieve etching rates in modified fused silica up to 820 µm/h and selectivity up to ∼3000. This is used to produce a high aspect ratio (up to 1:1000), straight and spiral microfluidic channels which are embedded inside a volume of glass. Complex 3D glass micro-structures are also demonstrated.

Optimization of selective laser etching (SLE) for glass micromechanical structure fabrication.

In this work, we show how femtosecond (fs) laser-based selective glass etching (SLE) can be used to expand capabilities in fabricating 3D structures out of a single piece of glass. First, an investigation of the etching process is performed, taking into account various laser parameters and scanning strategies. These results provide critical insights into the optimization of the process allowing to increase manufacturing throughput. Afterward, various complex 3D glass structures such as microfluidic elements embedded inside the volume of glass or channel systems with integrated functional elements are produced. A single helix spring of 1 mm diameter is also made, showing the possibility to compress it by 50%. Finally, 3D structuring capabilities are used to produce an assembly-free movable ball-joint-based chain and magnet-actuated Geneva mechanism. Due to minimized friction caused by low (down to 200 nm RMS) surface roughness of SLE-produced structures, the Geneva mechanism was shown to be capable of rotating up to 2000 RPM.

Femtosecond Laser-Based Integration of Nano-Membranes into Organ-on-a-Chip Systems.

Organ-on-a-chip devices are gaining popularity in medical research due to the possibility of performing extremely complex living-body-resembling research in vitro. For this reason, there is a substantial drive in developing technologies capable of producing such structures in a simple and, at the same time, flexible manner. One of the primary challenges in producing organ-on-chip devices from a manufacturing standpoint is the prevalence of layer-by-layer bonding techniques, which result in limitations relating to the applicable materials and geometries and limited repeatability. In this work, we present an improved approach, using three dimensional (3D) laser lithography for the direct integration of a functional part-the membrane-into a closed-channel system. We show that it allows the freely choice of the geometry of the membrane and its integration into a complete organ-on-a-chip system. Considerations relating to sample preparation, the writing process, and the final preparation for operation are given. Overall, we consider that the broader application of 3D laser lithography in organ-on-a-chip fabrication is the next logical step in this field's evolution.

Stitchless support-free 3D printing of free-form micromechanical structures with feature size on-demand.

Femtosecond laser based 3D nanolithography is a powerful tool for fabricating various functional micro- and nano-objects. In this work we present several advances needed to push it from the laboratory level use to the industrial production lines. First, linear stage and galvo-scanners synchronization is employed to produce stitch-free mm-sized structures. Furthermore, it is shown that by varying objective numerical apertures (NA) from 1.4 NA to 0.45 NA, voxel size can be tuned in the range from sub µm to tens of mm, resulting in structuring rates between 1809 µm3/s and 313312 µm3/s at 1 cm/s translation velocity achieved via simultaneous movement of linear stages and scanners. Discovered voxel/throughput scaling peculiarities show good agreement to ones acquired with numerical modeling. Furthermore, support-free 3D printing of complex structures is demonstrated. It is achieved by choosing pre-polymer that is in hard gel form during laser writing and acts as a dissolvable support during manufacturing. All of this is combined to fabricate micromechanical structures. First, 1:40 aspect ratio cantilever and 1.5 mm diameter single-helix spring capable of sustaining extreme deformations for prolonged movement times (up to 10000 deformation cycles) are shown. Then, free-movable highly articulated intertwined micromechanical spider and squids (overall size up to 10 mm) are printed and their movement is tested. The presented results are discussed in the broader sense, touching on the stitching/throughput dilemma and comparing it to the standard microstereolithography. It is shown where multiphoton polymerization can outpace standard stereolithography in terms of throughput while still maintaining superior resolution and higher degree of freedom in terms of printable geometries.