Cytotoxicity and Microbiological Properties of Copolymers Comprising Quaternary Ammonium Urethane-Dimethacrylates with Bisphenol A Glycerolate Dimethacrylate and Triethylene Glycol Dimethacrylate.

Using dental composite restorative materials with a copolymeric matrix chemically modified towards bioactive properties can help fight secondary caries. In this study, copolymers of 40 wt.% bisphenol A glycerolate dimethacrylate, 40 wt.% quaternary ammonium urethane-dimethacrylates (QAUDMA-m, where m represents 8, 10, 12, 14, 16 and 18 carbon atoms in the N-alkyl substituent), and 20 wt.% triethylene glycol dimethacrylate (BG:QAm:TEGs) were tested for (i) cytotoxicity on the L929 mouse fibroblast cell line; (ii) fungal adhesion, fungal growth inhibition zone, and fungicidal activity against C. albicans; and (iii) bactericidal activity against S. aureus and E. coli. BG:QAm:TEGs had no cytotoxic effects on L929 mouse fibroblasts because the reduction of cell viability was less than 30% compared to the control. BG:QAm:TEGs also showed antifungal activity. The number of fungal colonies on their surfaces depended on the water contact angle (WCA). The higher the WCA, the greater the scale of fungal adhesion. The fungal growth inhibition zone depended on the concentration of QA groups (xQA). The lower the xQA, the lower the inhibition zone. In addition, 25 mg/mL BG:QAm:TEGs suspensions in culture media showed fungicidal and bactericidal effects. In conclusion, BG:QAm:TEGs can be recognized as antimicrobial biomaterials with negligible biological patient risk.

Can Modification with Urethane Derivatives or the Addition of an Anti-Hydrolysis Agent Influence the Hydrolytic Stability of Resin Dental Composite?

Due to the questionable durability of dental restorations, there is a need to increase the lifetime of composite restoration. The present study used diethylene glycol monomethacrylate/4,4'-methylenebis(cyclohexyl isocyanate) (DEGMMA/CHMDI), diethylene glycol monomethacrylate/isophorone diisocyanate (DEGMMA/IPDI) monomers, and bis(2,6-diisopropylphenyl)carbodiimide (CHINOX SA-1) as modifiers of a polymer matrix (40 wt% urethane dimethacrylate (UDMA), 40 wt% bisphenol A ethoxylateddimethacrylate (bis-EMA), and 20 wt% triethyleneglycol dimethacrylate (TEGDMA)). Flexural strength (FS), diametral tensile strength (DTS), hardness (HV), sorption, and solubility were determined. To assess hydrolytic stability, the materials were tested before and after two aging methods (I-7500 cycles, 5 °C and 55 °C, water and 7 days, 60 °C, 0.1 M NaOH; II-5 days, 55 °C, water and 7 days, 60 °C, 0.1 M NaOH). The aging protocol resulted in no noticeable change (median values were the same as or higher than the control value) or a decrease in the DTS value from 4 to 28%, and a decrease in the FS value by 2 to 14%. The hardness values after aging were more than 60% lower than those of the controls. The used additives did not improve the initial (control) properties of the composite material. The addition of CHINOX SA-1 improved the hydrolytic stability of composites based on UDMA/bis-EMA/TEGDMA monomers, which could potentially extend the service life of the modified material. Extended studies are needed to confirm the possible use of CHINOX SA-1 as an antihydrolysis agent in dental composites.

Physicochemical Properties of Novel Copolymers of Quaternary Ammonium UDMA Analogues, Bis-GMA, and TEGDMA.

This study aimed to elucidate the physicochemical properties of copolymers comprising 40 wt.% bisphenol A glycerolate dimethacrylate (Bis-GMA), 40 wt.% quaternary ammonium urethane-dimethacrylate analogues (QAUDMA-m, where m corresponds to the number of carbon atoms in the N-alkyl substituent), and 20 wt.% triethylene glycol dimethacrylate (TEGDMA) copolymers (BG:QAm:TEGs). The BG:QAm:TEG liquid monomer compositions and reference compositions (40 wt.% Bis-GMA, 40 wt.% urethane-dimethacrylate (UDMA), 20 wt.% TEGDMA (BG:UD:TEG) and 60 wt.% Bis-GMA, 40 wt.% TEGDMA (BG:TEG)) were characterized in terms of their refractive index (RI) and monomer glass transition temperature (Tgm) and then photocured. The resulting copolymers were characterized in terms of the polymer glass transition temperature (Tgp), experimental polymerization shrinkage (Se), water contact angle (WCA), water sorption (WS), and water solubility (SL). The prepared BG:QAm:TEG liquid monomer compositions had RI in the range 1.4997-1.5129, and Tgm in the range -52.22 to -42.12 °C. The BG:QAm:TEG copolymers had Tgp ranging from 42.21 to 50.81 °C, Se ranging from 5.08 to 6.40%, WCA ranging from 81.41 to 99.53°, WS ranging from 25.94 to 68.27 µg/mm3, and SL ranging from 5.15 to 5.58 µg/mm3. Almost all of the developed BG:QAm:TEGs fulfilled the requirements for dental materials (except BG:QA8:TEG and BG:QA10:TEG, whose WS values exceeded the 40 µg/mm3 limit).

Characterization of the Mechanical Properties, Water Sorption, and Solubility of Antibacterial Copolymers of Quaternary Ammonium Urethane-Dimethacrylates and Triethylene Glycol Dimethacrylate.

The use of dental composites based on dimethacrylates that have quaternary ammonium groups is a promising solution in the field of antibacterial restorative materials. This study aimed to investigate the mechanical properties and behaviors in aqueous environments of a series of six copolymers (QA:TEG) comprising 60 wt.% quaternary ammonium urethane-dimethacrylate (QAUDMA) and 40 wt.% triethylene glycol dimethacrylate (TEGDMA); these copolymers are analogous to a common dental copolymer (BG:TEG), which comprises 60 wt.% bisphenol A glycerolate dimethacrylate (Bis-GMA) and 40 wt.% TEGDMA. Hardness (HB), flexural strength (FS), flexural modulus (E), water sorption (WS), and water solubility (SL) were assessed for this purpose. The pilot study of these copolymers showed that they have high antibacterial activity and good physicochemical properties. This paper revealed that QA:TEGs cannot replace BG:TEG due to their insufficient mechanical properties and poor behavior in water. However, the results can help to explain how QAUDMA-based materials work, and how their composition should be manipulated to produce the best performance. It was found that the longer the N-alkyl chain, the lower the HB, WS, and SL. The FS and E increased with the lengthening of the N-alkyl chain from eight to ten carbon atoms. Its further extension, to eighteen carbon atoms, caused a decrease in those parameters.

Novel Antibacterial Copolymers Based on Quaternary Ammonium Urethane-Dimethacrylate Analogues and Triethylene Glycol Dimethacrylate.

The growing scale of secondary caries and occurrence of antibiotic-resistant bacterial strains require the development of antibacterial dental composites. It can be achieved by the chemical introduction of quaternary ammonium dimethacrylates into dental composites. In this study, physicochemical and antibacterial properties of six novel copolymers consisting of 60 wt. % quaternary ammonium urethane-dimethacrylate analogues (QAUDMA) and 40 wt. % triethylene glycol dimethacrylate (TEGDMA) were investigated. Uncured compositions had suitable refractive index (RI), density (dm), and glass transition temperature (Tgm). Copolymers had low polymerization shrinkage (S), high degree of conversion (DC) and high glass transition temperature (Tgp). They also showed high antibacterial effectiveness against S. aureus and E. coli bacterial strains. It was manifested by the reduction in cell proliferation, decrease in the number of bacteria adhered on their surfaces, and presence of growth inhibition zones. It can be concluded that the copolymerization of bioactive QAUDMAs with TEGDMA provided copolymers with high antibacterial activity and rewarding physicochemical properties.

Synthesis and Characterization of Novel Quaternary Ammonium Urethane-Dimethacrylate Monomers-A Pilot Study.

Six novel urethane-dimethacrylate analogues (QAUDMAs) were synthesized and characterized. They consisted of the 2,4,4,-trimethylhexamethylene diisocyanate (TMDI) core and two methacrylate-terminated wings containing quaternary ammonium groups substituted with alkyl chains of 8, 10, 12, 14, 16, or 18 carbon atoms. QAUDMAs, due to the presence of quaternary ammonium groups, may have possible antibacterial effects. Since they showed satisfactory physicochemical properties, they will be subjected to further research towards the development of dental composites with a capacity to reduce secondary caries. The synthesis of QAUDMAs included three stages: (i) transesterification of methyl methacrylate (MMA) with N-methyldiethanolamine (MDEA), (ii) N-alkylation of the tertiary amino group with alkyl bromide, and (iii) addition of TMDI to the intermediate achieved in the second stage. The formation of QAUDMAs was confirmed by 1H and 13C NMR. They were characterized for density (dm), viscosity (η), refractive index (RI), glass transition temperature (Tg), polymerization shrinkage (S), and degree of conversion (DC). QAUDMAs were yellow, viscous resins (the η values ranged from 1.28 × 103 to 1.39 × 104 Pa·s, at 50 °C). Their RI ranged from 1.50 to 1.52, Tg from -31 to -15 °C, DC from 53 to 78%, and S from 1.24 to 2.99%, which is appropriate for dental applications.

Physicochemical and Mechanical Properties of Bis-GMA/TEGDMA Dental Composite Resins Enriched with Quaternary Ammonium Polyethylenimine Nanoparticles.

Modification of dental monomer compositions with antimicrobial agents must not cause deterioration of the structure, physicochemical, or mechanical properties of the resulting polymers. In this study, 0.5, 1, and 2 wt.% quaternary ammonium polyethylenimine nanoparticles (QA-PEI-NPs) were obtained and admixed with a Bis-GMA/TEGDMA (60:40) composition. Formulations were then photocured and tested for their degree of conversion (DC), polymerization shrinkage (S), glass transition temperature (Tg), water sorption (WS), solubility (SL), water contact angle (WCA), flexural modulus (E), flexural strength (σ), hardness (HB), and impact resistance (an). We found that the DC, S, Tg, WS, E, and HB were not negatively affected by the addition of QA-PEI-NPs. Changes in these values rarely reached statistical significance. On the other hand, the SL increased upon increasing the QA-PEI-NPs concentration, whereas σ and an decreased. These results were usually statistically significant. The WCA values increased slightly, but they remained within the range corresponding to hydrophilic surfaces. To conclude, the addition of 1 wt.% QA-PEI-NPs is suitable for applications in dental materials, as it ensures sufficient physicochemical and mechanical properties.

Novel Urethane-Dimethacrylate Monomers and Compositions for Use as Matrices in Dental Restorative Materials.

In this study, novel urethane-dimethacrylate monomers were synthesized from 1,3-bis(1-isocyanato-1-methylethyl)benzene (MEBDI) and oligoethylene glycols monomethacrylates, containing one to three oxyethylene groups. They can potentially be utilized as matrices in dental restorative materials. The obtained monomers were used to prepare four new formulations. Two of them were solely composed of the MEBDI-based monomers. In a second pair, a monomer based on triethylene glycol monomethacrylate, used in 20 wt.%, was replaced with triethylene glycol dimethacrylate (TEGDMA), a reactive diluent typically used in dental materials. For comparison purposes, two formulations, using typical dental dimethacrylates (bisphenol A glycerolate dimethacrylate (Bis-GMA), urethane-dimethacrylate (UDMA) and TEGDMA) were prepared. The monomers and mixtures were tested for the viscosity and density. The homopolymers and copolymers, obtained via photopolymerization, were tested for the degree of conversion, polymerization shrinkage, water sorption and solubility, hardness, flexural strength and modulus. The newly developed formulations achieved promising physico-chemical and mechanical characteristics so as to be suitable for applications as dental composite matrices. A combination of the MEBDI-based urethane-dimethacrylates with TEGDMA resulted in copolymers with a high degree of conversion, low polymerization shrinkage, low water sorption and water solubility, and good mechanical properties. These parameters showed an improvement in relation to currently used dental formulations.

DMA analysis of the structure of crosslinked poly(methyl methacrylate)s.

PURPOSE: This paper presents the study aimed at the development of crosslinked poly(methyl methacrylate)s (X-PMMA) of varied crosslink density and the investigation of the relationships between the polymer network structure and dynamic mechanical properties. METHODS: A series of model X-PMMA networks were crosslinked by the introduction of: 1, 2, 5, 10 and 20% of triethylene glycol dimethacrylate (TEGDMA). The copolymerizations led to various glass-rubber relaxation properties of the polymer networks, as revealed by dynamic-mechanical analysis (DMA). Glass temperature (Tg) and storage modulus above the Tg (Erubbery ) were a sensitive function of network architecture. DMA data were used for calculating the network parameter (Mc), crosslink density (q) and its alternative measure - the degree of crosslinking (DX). RESULTS: The viscoelastic properties as well as structural parameters calculated from those showed correlation with the amount of the crosslinker. The increase in TEGDMA content resulted in the Tg, q and DX increases, whereas Mc decrease. The possible incomplete conversion of double bonds was detected in the DMA analysis, which was confirmed by the degree of conversion (DC), measured by FTIR spectroscopy. Additionally, some amount of sol fraction was found by 1H NMR experiments. CONCLUSIONS: The structure-property relationships developed for the system presented in this work could be useful in tissue engineering, where X-PMMA is applied. The direct measure of storage modulus values before and above glass transition may serve as a simple and fast indicator of the X-PMMA crosslink density.

The novel semi-biodegradable interpenetrating polymer networks based on urethane-dimethacrylate and epoxy-polyester components as alternative biomaterials.

PURPOSE: This paper presents the pilot study aimed at the development of new full interpenetrating polymer networks based on urethane- dimethacrylate and biodegradable epoxy-polyester as the proposition of new biomaterials with gradually emerging porosity. METHODS: The urethane-dimethacrylate monomer was obtained from 4,4'-methylenebis(phenyl isocyanate) and tetraethylene glycol monomethacrylate. The redox-initiating system was employed for its radical polymerization. The epoxy-polyester was produced by oxidation of the polyester, synthesized from succinic anhydride and allyl glicydyl ether. It was cured in a step-growth process with biogenic, aliphatic amine - spermidine. The mixtures of both monomers with adequate curing agents were room temperature polymerized. The hardened materials were characterized for damping behavior and dynamic modulus, hardness, water sorption, the course of hydrolytic degradation as well as the morphology - before and during the degradation process. RESULTS: The cured materials revealed the nonporous, dense morphology. In the hydrolytic environment, the epoxy-polyester network degraded and the porous urethane-dimethacrylate scaffold remained. The epoxy-polyester appeared to prevent the urethane-dimethacrylate from attaining a high degree of conversion, even if the polymerization rate and the molecular mobility of the latter one are higher than those of the epoxy-polyester. The most homogeneous material with the best physico-mechanical properties was obtained when the urethane-dimethacrylate content was smaller than the epoxy-polyester content, respectively 25 and 50 wt%. CONCLUSIONS: The system presented in this work could be useful in tissue engineering, where at the beginning of the tissue regeneration process it would meet the implant mechanical properties and then would deliver its porosity, facilitating the tissue regeneration process.

Characterization of urethane-dimethacrylate derivatives as alternative monomers for the restorative composite matrix.

OBJECTIVE: The aim was accomplished by a comparative analysis of the physicochemical properties of urethane-dimethacrylate (UDMA) monomers and their homopolymers with regard to the properties of basic dimethacrylates used presently in dentistry. The homologous series of UDMA were obtained from four oligoethylene glycols monomethacrylates (HEMA, DEGMMA, TEGMMA and TTEGMMA) and six diisocyanates (HMDI, TMDI, IPDI, CHMDI, TDI and MDI). METHODS: Photopolymerization was light-initiated with the camphorquinone/tertiary amine system. Monomers were tested for viscosity and density. Flexural strength, flexural modulus, hardness, water sorption and polymerization shrinkage of the polymers were studied. The glass transition temperature and the degree of conversion were also discussed. RESULTS: HEMA/IPDI appeared to be the most promising alternative monomer. The monomer exhibited a lower viscosity and achieved higher degree of conversion, the polymer had lower water sorption as well as higher modulus, glass temperature and hardness than Bis-GMA. The polymer of DEGMMA/CHMDI exhibited lower polymerization shrinkage, lower water sorption and higher hardness, however it exhibited lower modulus when compared to HEMA/TMDI. The remaining monomers obtained from HEMA were solids. Monomers with longer TEGMMA and TTEGMMA units polymerized to rubbery networks with high water sorption. The viscosity of all studied UDMA monomers was too high to be used as reactive diluents. SIGNIFICANCE: The systematic, comparative analysis of the homologous UDMA monomers and corresponding homopolymers along with their physico-mechanical properties are essential for optimizing the design process of new components desirable in dental formulations. Some of the studied UDMA monomers may be simple and effective alternative dimethacrylate comonomers.

Fractal analysis of heterogeneous polymer networks formed by photopolymerization of dental dimethacrylates.

OBJECTIVES: In this work the influence of the dimethacrylate monomer chemical structure on structural heterogeneity and physico-mechanical properties of the resulting polymer networks was investigated. Rigid aromatic dimethacrylate (Bis-GMA), triethylene glycol dimethacrylate (TEGDMA) and flexible aliphatic urethane-dimethacrylate (UDMA) were chosen for room-temperature homopolymerizations and copolymerizations induced by camphorquinone/N,N-dimethylaminoethyl methacrylate photoinitiating system. METHODS: Atomic force microscopy (AFM) was used for visualizing the morphology of poly(dimethacrylate)s, which was described by: the fractal dimension (D(F)), the generalized fractal dimensions (D(q) and ΔD) as well as the modified fractal dimension (D(ß)). Estimated fractal characteristics were correlated with polymer density, hardness and impact strength. RESULTS: AFM images of fractured surfaces revealed the highly complex morphology of dimethacrylate polymer networks. They were found to possess the fractal character. The fractal parameters were observed to be proportional to the density, hardness and impact resistance of investigated polymers. ΔD appeared to be a good indicator of the structural heterogeneity of dimethacrylate networks. The results suggest that the fracture behavior of poly(dimethacrylate) matrix of dental materials can be controlled by the fractal morphology. SIGNIFICANCE: Correlating the morphological studies with the mechanical tests would be beneficial in defining the role of morphology in the mechanical behavior of dimethacrylate networks and consequently, lead to the development of a reliable method for identifying the cause of dental material failures under stress. Thus, fractal analysis could become one of the key elements in designing and developing dental materials.

Structure-property relationships in dimethacrylate networks based on Bis-GMA, UDMA and TEGDMA.

OBJECTIVES: In this work the influence of structural heterogeneity of poly(dimethacrylate)s on mechanical properties was investigated. Rigid aromatic dimethacrylate (Bis-GMA), triethylene glycol dimethacrylate (TEGDMA) and flexible aliphatic urethane dimethacrylate (UDMA) have been chosen for room-temperature homopolymerizations and copolymerizations induced by a camphorquinone/N,N-dimethylaminoethyl methacrylate photoinitiating system. METHODS: The following mechanical properties of poly(dimethacrylate)s were investigated: flexural modulus, flexural strength, impact strength and hardness. Atomic force microscopy (AFM) and X-ray powder diffraction (XRPD) were used to describe the morphology of polymer networks. RESULTS: AFM observations showed that the heterogeneity of networks is spatially organized due to the formation of microgels and their agglomeration. Observed agglomerates are unidirectionally oriented, parallel to the direction of polymerization shrinkage. Of all the investigated mechanical properties of poly(dimethacrylate)s, the impact resistance appeared to be the least. The origin of this brittleness could be the presence of heterogeneities which were quantitatively characterized by means of XRPD. The impact resistance was shown to be related to the size of network heterogeneities which is probably influenced by intermolecular interactions, such as hydrogen bonding. SIGNIFICANCE: Differences in monomer structure resulted in significantly different morphology and physical properties of the polymer networks which had been studied. The size and shape of heterogeneities affected the final mechanical properties of the polymers, especially impact resistance. In addition, the combined application of XRPD and AFM techniques can be a successful tool in the analysis of the dimethacrylate network morphology, and finally, in investigations on methacrylate-based dental materials.